Beruflich Dokumente
Kultur Dokumente
Q2
Slab area 30 m^2
axial load 720 kN/m
Point A B C D E F
Axial load 720 720 720 720 720 720
In-plane Mt 0 0 0 0 0 0
Tranverse Mt 52.68787322 52.687873222 52.68787322 52.68787322 52.68787322 52.68787322
N/bh 0 0 0 0 0 0
M/bh^2 4.215029858 4.2150298578 4.215029858 4.215029858 4.215029858 4.215029858
p(%), close to 3% 3% 3% 3% 3% 3%
Re-bars(BF)
bar 25 @ 125 at both face
mm f_cu 30 MPa
mm Surcharge 5 kN/m^2
mm Water pressur 10 kN/m^3
mm conc density 24 kN/m^3
mm soil density 21 kN/m^3
0.848
kN/m^2
kN/m^2
KN/m^2
kN/m
kN/m
kN/m
kN
kN
kN Q1
4.215029858 M/bh^2 % get
51562.5 % * area
25781.25 go for one side
3437.5 go for unit meter
bar 25 @ 125 at both face
52.68787322 or 10.8
0
4.215029858
3% 60000
30000
r 25 @ 125 at both face 3750
I. Determine the design forces Round Clause Eqn
Ka 0.2174428321 0.22
Lateral Force from soil
F_A 57.75 58 kN
Lateral Force from surcharge
F_S 5.5 5.5 kN
Lateral Force from water pressure
F_W 125 125 kN
II. Determine the design moment
Design moment at base
M_D 446.25 446 kNm
Effective Depth
d 200 200 mm
K 0.2027272727 0.2 6.1.2.4 6.7
K' 0.156 6.1.2.4 6.8
K<K'? N,Doubly reinforced
z 155.377492419 155 mm 6.1.2.4 6.13
z<0.95d? Y,z is the limit
Level arm
x (for f_cu 100 100 mm 6.1.2.4 6.14
x (for 40< f 112.5 113 mm
x (for 70< f 125 125 mm
d'/x 0.2654867257 0.27
d'/x<0.43? Y,comp. bars have yielded
For d'x<=0.43 For d'/x >0.43
f_sc=0.87*f_v sigma_sc = 0.0035(x-d')/x & f_sc = Es* sigma_sc
As' 1511.00920128 1511 mm^2 6.1.2.4 6.15
As 7043.71751221 7044 mm^2 6.1.2.4 6.16
Tension steel required
Provide T 40 - 175
For Cond.2
Say fy_v = 250 MPa
Shear links
A_sv/s_v 2.2528735632 2.25 mm s_v= bar spacing
Say fy = 250 MPa
Provide Y 10 - 200
A_sv_prov/s_ 1.5707963268 1.57 mm
A_sv_prov/s_v>A_sv/s_v N,try again
Shaded region
500
b1=250
b2=250 500
L-shaped wall
c/c
he procedures to design for moment, M, are:
he effective sectional dimensions and design parameters.
the K value and check if K < K'.
the lever arm z and check its limits.
the amount of steel required, As and/or A's.
e the size and number of bars.
he limits to steel area ratio are complied with.
forcement
N,more rebar
T 16 - 150
201.0619298
70
14074.33509
1.125946807 >=1? Y
52 >=6? Y
16 >=16 Y
150 <=150 Y
ll bars tied by links