Beruflich Dokumente
Kultur Dokumente
LED TV
SERVICE MANUAL
CHASSIS : LW45A
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CONTENTS . ............................................................................................. 2
SERVICING PRECAUTIONS..................................................................... 4
SPECIFICATION........................................................................................ 6
ADJUSTMENT INSTRUCTION................................................................. 8
BLOCK DIAGRAM................................................................................... 24
Copyright LG Electronics. Inc. All rights reserved. -2- LGE Internal Use Only
Only for training and service purposes
SAFETY PRECAUTIONS
Copyright LG Electronics. Inc. All rights reserved. -3- LGE Internal Use Only
Only for training and service purposes
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this service 2. After removing an electrical assembly equipped with ES
manual and its supplements and addenda, read and follow the devices, place the assembly on a conductive surface such as
SAFETY PRECAUTIONS on page 3 of this publication. aluminum foil, to prevent electrostatic charge buildup or expo-
NOTE: If unforeseen circumstances create conflict between the sure of the assembly.
following servicing precautions and any of the safety precautions 3. Use only a grounded-tip soldering iron to solder or unsolder
on page 3 of this publication, always follow the safety precau- ES devices.
tions. Remember: Safety First. 4. Use only an anti-static type solder removal device. Some sol-
der removal devices not classified as anti-static can generate
General Servicing Precautions electrical charges sufficient to damage ES devices.
1. Always unplug the receiver AC power cord from the AC power 5. Do not use freon-propelled chemicals. These can generate
source before; electrical charges sufficient to damage ES devices.
a. Removing or reinstalling any component, circuit board 6. Do not remove a replacement ES device from its protective
module or any other receiver assembly. package until immediately before you are ready to install it.
b. Disconnecting or reconnecting any receiver electrical plug (Most replacement ES devices are packaged with leads elec-
or other electrical connection. trically shorted together by conductive foam, aluminum foil or
c. Connecting a test substitute in parallel with an electrolytic comparable conductive material).
capacitor in the receiver. 7. Immediately before removing the protective material from the
CAUTION: A wrong part substitution or incorrect polarity leads of a replacement ES device, touch the protective mate-
installation of electrolytic capacitors may result in an explo- rial to the chassis or circuit assembly into which the device will
sion hazard. be installed.
2. Test high voltage only by measuring it with an appropriate CAUTION: Be sure no power is applied to the chassis or cir-
high voltage meter or other voltage measuring device (DVM, cuit, and observe all other safety precautions.
FETVOM, etc) equipped with a suitable high voltage probe. 8. Minimize bodily motions when handling unpackaged replace-
Do not test high voltage by "drawing an arc". ment ES devices. (Otherwise harmless motion such as the
3. Do not spray chemicals on or near this receiver or any of its brushing together of your clothes fabric or the lifting of your
assemblies. foot from a carpeted floor can generate static electricity suf-
4. Unless specified otherwise in this service manual, clean ficient to damage an ES device.)
electrical contacts only by applying the following mixture to the
contacts with a pipe cleaner, cotton-tipped stick or comparable General Soldering Guidelines
non-abrasive applicator; 10 % (by volume) Acetone and 90 % 1. Use a grounded-tip, low-wattage soldering iron and appropri-
(by volume) isopropyl alcohol (90 % - 99 % strength) ate tip size and shape that will maintain tip temperature within
CAUTION: This is a flammable mixture. the range or 500 F to 600 F.
Unless specified otherwise in this service manual, lubrication 2. Use an appropriate gauge of RMA resin-core solder composed
of contacts in not required. of 60 parts tin/40 parts lead.
5. Do not defeat any plug/socket B+ voltage interlocks with which 3. Keep the soldering iron tip clean and well tinned.
receivers covered by this service manual might be equipped. 4. Thoroughly clean the surfaces to be soldered. Use a mall wire-
6. Do not apply AC power to this instrument and/or any of its bristle (0.5 inch, or 1.25 cm) brush with a metal handle.
electrical assemblies unless all solid-state device heat sinks Do not use freon-propelled spray-on cleaners.
are correctly installed. 5. Use the following unsoldering technique
7. Always connect the test receiver ground lead to the receiver a. Allow the soldering iron tip to reach normal temperature.
chassis ground before connecting the test receiver positive (500 F to 600 F)
lead. b. Heat the component lead until the solder melts.
Always remove the test receiver ground lead last. c. Quickly draw the melted solder with an anti-static, suction-
8. Use with this receiver only the test fixtures specified in this type solder removal device or with solder braid.
service manual. CAUTION: Work quickly to avoid overheating the circuit
CAUTION: Do not connect the test fixture ground strap to any board printed foil.
heat sink in this receiver. 6. Use the following soldering technique.
a. Allow the soldering iron tip to reach a normal temperature
Electrostatically Sensitive (ES) Devices (500 F to 600 F)
Some semiconductor (solid-state) devices can be damaged eas- b. First, hold the soldering iron tip and solder the strand
ily by static electricity. Such components commonly are called against the component lead until the solder melts.
Electrostatically Sensitive (ES) Devices. Examples of typical ES c. Quickly move the soldering iron tip to the junction of the
devices are integrated circuits and some field-effect transistors component lead and the printed circuit foil, and hold it there
and semiconductor chip components. The following techniques only until the solder flows onto and around both the compo-
should be used to help reduce the incidence of component dam- nent lead and the foil.
age caused by static by static electricity. CAUTION: Work quickly to avoid overheating the circuit
1. Immediately before handling any semiconductor component or board printed foil.
semiconductor-equipped assembly, drain off any electrostatic d. Closely inspect the solder area and remove any excess or
charge on your body by touching a known earth ground. Alter- splashed solder with a small wire-bristle brush.
natively, obtain and wear a commercially available discharg-
ing wrist strap device, which should be removed to prevent
potential shock reasons prior to applying power to the unit
under test.
Copyright LG Electronics. Inc. All rights reserved. -4- LGE Internal Use Only
Only for training and service purposes
IC Remove/Replacement 3. Solder the connections.
Some chassis circuit boards have slotted holes (oblong) through CAUTION: Maintain original spacing between the replaced
which the IC leads are inserted and then bent flat against the cir- component and adjacent components and the circuit board to
cuit foil. When holes are the slotted type, the following technique prevent excessive component temperatures.
should be used to remove and replace the IC. When working with
boards using the familiar round hole, use the standard technique Circuit Board Foil Repair
as outlined in paragraphs 5 and 6 above. Excessive heat applied to the copper foil of any printed circuit
board will weaken the adhesive that bonds the foil to the circuit
Removal board causing the foil to separate from or "lift-off" the board. The
1. Desolder and straighten each IC lead in one operation by following guidelines and procedures should be followed when-
gently prying up on the lead with the soldering iron tip as the ever this condition is encountered.
solder melts.
2. Draw away the melted solder with an anti-static suction-type At IC Connections
solder removal device (or with solder braid) before removing To repair a defective copper pattern at IC connections use the
the IC. following procedure to install a jumper wire on the copper pattern
Replacement side of the circuit board. (Use this technique only on IC connec-
1. Carefully insert the replacement IC in the circuit board. tions).
2. Carefully bend each IC lead against the circuit foil pad and
solder it. 1. Carefully remove the damaged copper pattern with a sharp
3. Clean the soldered areas with a small wire-bristle brush. knife. (Remove only as much copper as absolutely necessary).
(It is not necessary to reapply acrylic coating to the areas). 2. carefully scratch away the solder resist and acrylic coating (if
used) from the end of the remaining copper pattern.
"Small-Signal" Discrete Transistor 3. Bend a small "U" in one end of a small gauge jumper wire and
Removal/Replacement carefully crimp it around the IC pin. Solder the IC connection.
1. Remove the defective transistor by clipping its leads as close 4. Route the jumper wire along the path of the out-away copper
as possible to the component body. pattern and let it overlap the previously scraped end of the
2. Bend into a "U" shape the end of each of three leads remain- good copper pattern. Solder the overlapped area and clip off
ing on the circuit board. any excess jumper wire.
3. Bend into a "U" shape the replacement transistor leads.
4. Connect the replacement transistor leads to the corresponding At Other Connections
leads extending from the circuit board and crimp the "U" with Use the following technique to repair the defective copper pattern
long nose pliers to insure metal to metal contact then solder at connections other than IC Pins. This technique involves the
each connection. installation of a jumper wire on the component side of the circuit
board.
Power Output, Transistor Device
Removal/Replacement 1. Remove the defective copper pattern with a sharp knife.
1. Heat and remove all solder from around the transistor leads. Remove at least 1/4 inch of copper, to ensure that a hazardous
2. Remove the heat sink mounting screw (if so equipped). condition will not exist if the jumper wire opens.
3. Carefully remove the transistor from the heat sink of the circuit 2. Trace along the copper pattern from both sides of the pattern
board. break and locate the nearest component that is directly con-
4. Insert new transistor in the circuit board. nected to the affected copper pattern.
5. Solder each transistor lead, and clip off excess lead. 3. Connect insulated 20-gauge jumper wire from the lead of the
6. Replace heat sink. nearest component on one side of the pattern break to the
lead of the nearest component on the other side.
Diode Removal/Replacement Carefully crimp and solder the connections.
1. Remove defective diode by clipping its leads as close as pos- CAUTION: Be sure the insulated jumper wire is dressed so the
sible to diode body. it does not touch components or sharp edges.
2. Bend the two remaining leads perpendicular y to the circuit
board.
3. Observing diode polarity, wrap each lead of the new diode
around the corresponding lead on the circuit board.
4. Securely crimp each connection and solder it.
5. Inspect (on the circuit board copper side) the solder joints of
the two "original" leads. If they are not shiny, reheat them and
if necessary, apply additional solder.
Copyright LG Electronics. Inc. All rights reserved. -5- LGE Internal Use Only
Only for training and service purposes
SPECIFICATION
NOTE : Specifications and others are subject to change without notice for improvement.
5. RGB-PC Input
No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz)
1. 640*480 31.469 59.94 25.175
2. 800*600 37.879 60.317 40.0
3. 1024*768 48.363 60.0 65.0
4. 1280*720 47.77 59.85 74.5
5. 1152*864 54.34 60.05 80
6. 1366*768 47.71 59.79 85.5
Copyright LG Electronics. Inc. All rights reserved. -6- LGE Internal Use Only
Only for training and service purposes
6. Component Video Input(Y, PB, PR)
No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed
1. 720*480 15.73 59.94 13.500 SDTV, DVD 480I(525I)
2. 720*480 15.75 60.00 13.514 SDTV, DVD 480I(525I)
3. 720*576 15.625 50.00 13.500 SDTV, DVD 576I(625I) 50Hz
4. 720*480 31.47 59.94 27.000 SDTV 480P
5. 720*480 31.50 60.00 27.027 SDTV 480P
6. 720*576 31.25 50.00 27.000 SDTV 576P 50Hz
7. 1280*720 44.96 59.94 74.176 HDTV 720P
8. 1280*720 45.00 60.00 74.250 HDTV 720P
9. 1280*720 37.50 50.00 74.25 HDTV 720P 50Hz
10. 1920*1080 28.125 50.00 74.250 HDTV 1080I 50Hz,
11. 1920*1080 33.72 59.94 74.176 HDTV 1080I
12. 1920*1080 33.75 60.00 74.25 HDTV 1080I
13. 1920*1080 56.25 50 148.5 HDTV 1080P
14. 1920*1080 67.432 59.94 148.350 HDTV 1080P
15. 1920*1080 67.5 60.00 148.5 HDTV 1080P
7. HDMI Input(DTV)
No. Resolution H-freq(kHz) V-freq.(kHz) Pixel clock(MHz) Proposed Remarks
1. 720*480 15.73 59.94 13.500 SDTV, DVD 480I(525I)
2. 720*480 15.75 60.00 13.514 SDTV, DVD 480I(525I) Spec. out but display.
3. 720*576 15.625 50.00 13.500 SDTV, DVD 576I(625I) 50Hz
4. 720*480 31.47 59.94 27 SDTV 480P
5. 720*480 31.5 60.00 27.027 SDTV 480P
6. 720*576 31.25 50.00 27 SDTV 576P
7. 1280*720 44.96 59.94 74.176 HDTV 720P
8. 1280*720 45 60.00 74.25 HDTV 720P
9. 1280*720 37.5 50.00 74.25 HDTV 720P
10. 1920*1080 28.125 50.00 74.25 HDTV 1080I
11. 1920*1080 33.72 59.94 74.176 HDTV 1080I
12. 1920*1080 33.75 60.00 74.25 HDTV 1080I
13. 1920*1080 56.25 50.00 148.5 HDTV 1080P
14. 1920*1080 67.432 59.94 148.350 HDTV 1080P
15. 1920*1080 67.5 60.00 148.5 HDTV 1080P
16. 1920*1080 27 24.00 74.25 HDTV 1080P
17. 1920*1080 33.75 30.00 74.25 HDTV 1080P
18. 1920*1080 26.97 23.97 74.25 HDTV 1080P
19. 1920*1080 33.716 29.976 74.25 HDTV 1080P
Copyright LG Electronics. Inc. All rights reserved. -7- LGE Internal Use Only
Only for training and service purposes
ADJUSTMENT INSTRUCTION
1. Application Range 3.2. EDID Download
This specification sheet is applied to all of the LED TV with 3.2.1. Overview
LW45A chassis. - I t is a VESA regulation. A PC or a MNT will display an
optimal resolution through information sharing without any
necessity of user input. It is a realization of Plug and Play.
2. Designation 3.2.2. Equipment
(1) Because this is not a hot chassis, it is not necessary to
- Since EDID data is embedded, EDID download JIG, HDMI
use an isolation transformer. However, the use of isolation
cable are not need.
transformer will help protect test instrument.
(2) Adjustment must be done in the correct order.
(3) The adjustment must be performed in the circumstance of 3.2.3. Download method
25 C 5 C of temperature and 65 % 10 % of relative - The EDID data is automatically saved.
humidity if there is no specific designation.
(4) The input voltage of the receiver must keep 100-220 V, 3.2.4. EDID DATA
50/60Hz. ** RGB : 128Bytes
(5) The receiver must be operated for over 5 minutes prior to 0 1 2 3 4 5 6 7 8 9 A B C D E F
the adjustment when module is in the circumstance of 0 00 FF FF FF FF FF FF 00 1E 6D C8 59 01 01 01 01
above 15 C. 10 01 17 01 03 68 34 1D 78 EA 53 4D A3 56 4F 9E 26
20 0F 47 4A A1 08 00 01 40 45 40 61 40 71 40 81 00
In case of keeping module is in the circumstance of 0 C, it
30 81 C0 01 01 01 01 66 21 56 AA 51 00 1E 30 46 8F
should be placed in the circumstance of above 15 C for 2
40 33 00 3F 43 21 00 00 1E 00 00 00 FD 00 38 3D 1E
hours. 50 45 09 00 0A 20 20 20 20 20 20 00 00 00 FC 00 32
In case of keeping module is in the circumstance of below 60 44 20 48 44 20 4C 47 20 54 56 0A 20 00 00 00 FF
-20 C, it should be placed in the circumstance of above 15 70 00 0A 20 20 20 20 20 20 20 20 20 20 20 20 00 67
C for 3 hours.
** HDMI 1 : 256Bytes
0 1 2 3 4 5 6 7 8 9 A B C D E F
* Caution 0 00 FF FF FF FF FF FF 00 1E 6D CA 59 01 01 01 01
When a still image is displayed for 20 minutes or longer 10 01 17 01 03 80 34 1D 78 EA 53 4D A3 56 4F 9E 26
(especially where W/B scale is strong. Digital pattern 13ch 20 0F 47 4A 21 08 00 81 80 81 C0 71 40 B3 00 81 40
and/or Cross hatch pattern 09ch), there can some 30 90 40 95 00 A9 C0 66 21 56 AA 51 00 1E 30 46 8F
afterimage in the black level area. 40 33 00 09 25 21 00 00 1A 02 3A 80 18 71 38 2D 40
50 58 2C 45 00 09 25 21 00 00 1E 00 00 00 FD 00 38
60 3D 1E 45 0F 00 0A 20 20 20 20 20 20 00 00 00 FC
70 00 32 44 20 48 44 20 4C 47 20 54 56 0A 20 01 30
3. ADC calibration 80 02 03 21 F1 4F 84 05 03 02 20 22 10 11 13 12 14
Adjust Sequence
4. White Balance Adjustment
aa 00 00 [Enter Adjust Mode] 4.1. Overview
xb 00 40 [Component1 Input (480i)] 4.1.1. W/B adj. Objective & How-it-works
ad 00 10 [Adjust 480i Comp1] (1) Objective: To reduce each Panels W/B deviation
xb 00 60 [RGB Input (1024*768)] (2) How-it-works: When R/G/B gain in the OSD is at 192, it
ad 00 10 [Adjust 1024*768 RGB] means the panel is at its Full Dynamic Range. In order to
aa 00 90 End Adjust mode prevent saturation of Full Dynamic range and data, one of
R/G/B is fixed at 192, and the other two is lowered to find
the desired value.
(3) Adj. condition: normal temperature
1) Surrounding Temperature: 25 C 5 C
2) Warm-up time: About 5 Min
3) Surrounding Humidity: 20% ~ 80%
4) B efore White balance adjustment, Keep power on
status, dont power off
Copyright LG Electronics. Inc. All rights reserved. -8- LGE Internal Use Only
Only for training and service purposes
4.1.2. Adj. condition and cautionary items 4.5. Adjustment method
(1) Lighting condition in surrounding area surrounding lighting 4.5.1. Auto WB calibration
should be lower 10 lux. (1) Set TV in ADJ mode using P-Only key(or POWER ON key).
Try to isolate adj. area into dark surrounding. (2) Place optical probe on the center of the display.
(2) Probe location: Color Analyzer(CA-210) probe should be - It need to check probe condition of zero calibration before
within 10 cm and perpendicular of the module surface adjustment.
(80~ 100) (3) Connect RS-232C Cable.
(3) Aging time (4) Select mode in ADJ Program and begin a adjustment.
1) After Aging Start, Keep the Power ON status during 5 (5) When WB adjustment is completed with OK message, check
Minutes. adjustment status of pre-set mode.(Cool, Medium, Warm)
2) In case of LCD, Back-light on should be checked using (6) Remove probe and RS-232C cable.
no signal or Full-white pattern. W/B Adj. must begin as start command wb 00 00 , and
finish as end command wb 00 ff, and Adj. offset if need.
4.2. Equipment
(1) Color Analyzer: CA-210(NCG: CH 9/ WCG: CH12/ LED: 4.5.2. LED White balance table
CH14) - If Model is Polaris Model, G-gain fix is applied.
(2) Adj. Computer(During auto adj., RS-232C protocol is needed) (1) Cool Mode
(3) Adjust Remte control 1) Purpose : Adjust the color temperature to reduce the
(4) Video Signal Generator MSPG-925F 720p/204-Gray deviation of the module color temperature.
(Model: 217, Pattern: 49) 2) P rinciple : To adjust the white balance without the
* Color Analyzer Matrix should be calibrated using CS-1000. saturation, Adjust the G gain more than 172 (If R gain or
G gain is more than 255, G gain can adjust less than
172) and change the others (R/B Gain).
4.3. Equipment connection 3) Adjustment mode : mode - Cool
Co lo r Analyzer
RS -232C
(2) Medium / Warm Mode
Probe
1) Purpose : Adjust the color temperature to reduce the
Co m p ut er
deviation of the module color temperature.
RS -232C
RS -232C
2) P rinciple : To adjust the white balance without the
Pat t ern Generat o r saturation, Fix the one of R/G/B gain to 192 (default
Signal Source
data) and decrease the others.
* If TV internal pattern is used, not needed 3) Adjustment mode : Two modes - Medium / Warm
4.6. R
eference(White Balance Adjustment
4.4. Adjustment Command (Protocol)
(1) RS-232C Command used during auto-adj. coordinate and color temperature)
(1) Luminance: 204 Gray, 80IRE
RS-232C COMMAND
Explanation (2) Standard color coordinate and temperature using CS-1000
CMD DATA ID
(over 26 inch)
wb 00 00 Begin White Balance adjustment
The spec of color temperature and coordinate.
End White Balance adjustment
wb 00 ff
(internal pattern disappears )
Mode Color Temp Color coordinate Remark
Cool x = 0.276 (0.03) * Test signal
13,000 K
(C50) y = 0.279 (0.03) - Inner pattern for
(2) Adjustment Map Medium x = 0.290 (0.03) W/B adjust
9,300 K
Command Data Range Default (0) y = 0.298 (0.03) - External white
Adj. item pattern
(lower caseASCII) (Hex.) (Decimal) Warm x = 0.318 (0.03)
CMD1 CMD2 MIN MAX 6,500 K (85IRE, 204gray)
(W50) y = 0.334 (0.03)
R Gain j g 00 C0
G Gain j h 00 C0
B Gain j i 00 C0
* Note : x,y coordinates are drifted about 0.007 after 30 mins
Cool
R Cut heat-run. So checking color coordinate within 5-min at
G Cut total assembly line, consider x,y coordinates might be
B Cut up to 0.007 than x,y target of each color temperature.
R Gain j a 00 C0
G Gain j b 00 C0
B Gain j c 00 C0
Medium
R Cut
G Cut
B Cut
R Gain j d 00 C0
G Gain j e 00 C0
Warm B Gain j f 00 C0
R Cut
G Cut
Copyright LG Electronics. Inc. All rights reserved. -9- LGE Internal Use Only
Only for training and service purposes
5. Tool Option setting & Inspection 9. USB S/W Download
* optional, Service only
per countries
(1) Press 'IN START' key at Factory Service remote control. (1) Put the USB Stick to the USB socket.
(2) Select 'Tool Option 1'. (2) Automatically detecting update file in USB Stick.
(3) Punch in the number and press 'OK'. (Each of models has - If your downloaded program version in USB Stick is lower
their number) than that of TV set, it didnt work.
(4) Correct 'Tool Option2' ~ 'Tool Option5'. Otherwise USB data is automatically detected.
(5) Completed adjusting Tool option. (3) Show the message Copying files from memory.
8.3. Checkpoint
(1) Test voltage
- GND: 1.5 KV / min at 100 mA
- SIGNAL: 3 KV / min at 100 mA
(2) TEST time: 1 second
(3) TEST POINT
-G ND Test = POWER CORD GND and SIGNAL CABLE
GND.
-H i-pot Test = POWER CORD GND and LIVE &
NEUTRAL.
(4) LEAKAGE CURRENT: At 0.5 mArms
Copyright LG Electronics. Inc. All rights reserved. - 10 - LGE Internal Use Only
Only for training and service purposes
10. Optional adjustments
10.1. Manual ADC Calibration
Enter EZ ADJUST mode by pressing ADJ key.
Enter Internal ADC calibration mode by pressing or OK
key at 7. ADC Calibration
EZ ADJUST ADC Calibration
0. Tool Option1
ADC Comp 480i NG
1. Tool Option2
ADC Comp 1080p NG
2. Tool Option3
ADC RGB NG
3. Tool Option4
4. Tool Option5
Start Reset
5. Country Group
6. Area Option
7. ADC Calibration
8. White Balance
9. 10 Point WB
10. Test Pattern
11. EDID D/L
12. Sub B/C
13. Touch Sensitivity Setting
14. Ext. Input Adjust
10.2.2. Equipment
(1) Color Analyzer: CA-210 (NCG: CH 9 / WCG: CH12 / LED:
CH14)
(2) Adj. Computer(During auto adj., RS-232C protocol is needed)
(3) Adjust Remot control
(4) Video Signal Generator MSPG-925F 720p/216-Gray
(Model: 217, Pattern: 78)
10.2.3. Adjustment
(1) Set TV in Adj. mode using POWER ON.
(2) Zero Calibrate the probe of Color Analyzer, then place it on
the center of LCD module within 10cm of the surface.
(3) Press ADJ key EZ adjust using adj. R/C 6. White-
Balance then press the cursor to the right (Key). When
Key() is pressed 216 Gray internal pattern will be
displayed.
(4) One of R Gain / G Gain / B Gain should be fixed at 192,
and the rest will be lowered to meet the desired value.
(5) Adj. is performed in COOL, MEDIUM, WARM 3 modes of
color temperature.
Copyright LG Electronics. Inc. All rights reserved. - 11 - LGE Internal Use Only
Only for training and service purposes
TROUBLE SHOOTING
1. NO POWER-Main PCBA
NO POWER
1 Is Adapter
NO check open or short at Line.
Output VOLTAGE 19.4V
or change Adapter.
through of JK700?
YES
YES
3
NO check the Lines of IC711,IC704
Is 1.8V at C745? If there is any problem at Line,
is 1.25V at C742? Change IC704,IC706.
YES
4
Check Line short or open between
NO
Check wavef orm of X501 IC501 and X501,
Change IC501 or change X501
YES
5
is 3.3V at 1pin of P120?
NO Change control
when push power key,
Or check Line short or open of P120
Is 0v at 2pin of P120?
YES
6
is there any waver at 11pin of P120, NO change IR board
when use remote controller? Or check Line short or open of P120
Insert F/W 4
X501
Copyright LG Electronics. Inc. All rights reserved. - 12 - LGE Internal Use Only
Only for training and service purposes
2. No raster (Power LED blue, black screen)
NO RASTER
(Screen is not displayed)
YES
Check Line short or open between
2 NO IC711/IC704 and IC501,
Is 1.25V at 4pin of IC704?
If there is any problem at Line,
Is 1.8V at 2pin of IC711?
Change IC711/IC704 or change IC501
YES
It is not over 3V at 1pin of IC601.
3 NO Change Q601.
is 3V at 1pin of IC601? Or check Line short or open between
R603 and 95pin of IC501.
Change IC 501.
YES
Copyright LG Electronics. Inc. All rights reserved. - 13 - LGE Internal Use Only
Only for training and service purposes
3. Abnormal/No screen (All input)-Main PCBA
Abnormal/No screen
(all input)
YES
If is not under 1.5V at R722,
change Q721 or check open and short
2 NO of Line among Q720 and Q721.
Is 12V at 1pin of P101?
If is under 11V at L110,
Check open and short
Of line between L110 and P101.
YES
YES
Change module
WAVEFORMS
Copyright LG Electronics. Inc. All rights reserved. - 14 - LGE Internal Use Only
Only for training and service purposes
4. Abnormal screen (TV)-Main PCBA
YES
If 1.7V is not at plus pin of TU401, check
2 NO It is over 3V at 2pin of IC711,
Is 1.8V at 7pin of TU401? if it is not, Check Line between TU401
and IC711 is open or short.
Another is change IC711 or TU401
WAVEFORMS
3 4
Copyright LG Electronics. Inc. All rights reserved. - 15 - LGE Internal Use Only
Only for training and service purposes
5. Abnormal screen (AV)-Main PCBA
1 NO
Put into AV cable completely? Insult AV cable tight
YES
YES
YES
Change IC501
WAVEFORMS
3
R505 (CVBS)
Copyright LG Electronics. Inc. All rights reserved. - 16 - LGE Internal Use Only
Only for training and service purposes
6. Abnormal screen (RGB PC)-Main PCBA
YES
YES
YES
Change IC501
WAVEFORMS
3
Copyright LG Electronics. Inc. All rights reserved. - 17 - LGE Internal Use Only
Only for training and service purposes
7. Abnormal screen (COMPONENT)-Main PCBA
YES
YES
YES
Change IC501
WAVEFORMS
3
Copyright LG Electronics. Inc. All rights reserved. - 18 - LGE Internal Use Only
Only for training and service purposes
8. Abnormal screen (HDMI)-Main PCBA
YES
YES
3 Can read EDID and Check Line between JK203 and IC501
HDCP key though is open or short, Another is
16,15pin of JK203 Change HDMI cable
YES
YES
YES
Check Line between JK203 and IC501
6 Is wavef orm at 1,3,4,6,7,9pin NO
is open or short, Another is
Of JK203? Change HDMI cable
YES
Change IC501
Copyright LG Electronics. Inc. All rights reserved. - 19 - LGE Internal Use Only
Only for training and service purposes
9. No sound (all source )-Main PCBA
1
NO
Does wire connect P301 with speaker? Connect wire between P301 and speaker.
YES
If 8V is not plus at L703, check
2 of JK700 is open.
Is 19.4V at 19,20,31,32pin NO
If is not Check Line between L703
of IC301 ? and IC301 is open or short.
.Another is change IC301
YES
If 3V is not plus 30pin of IC301,
3 check It is over 3V at L301
NO
Is 3.3V at 40pin of IC301? if it is not, Check Line between L301
and IC301 is open or short.
Another is change IC701,IC301
YES
4
Check Line between IC301 and IC501
Is I2C wavef orm at NO
is open or short, Another is change
10,11pin of IC301?
IC301 or IC501.
YES
5 Check Line between IC301 and IC501
Is I2S wavef orm at NO
is open or short, Another is change
R301,R302,R303,R304? IC301 or IC501.
4 5
5 6
Copyright LG Electronics. Inc. All rights reserved. - 20 - LGE Internal Use Only
Only for training and service purposes
10. Abnormal sound (TV)-Main PCBA
YES
WAVEFORMS
3 4
Copyright LG Electronics. Inc. All rights reserved. - 21 - LGE Internal Use Only
Only for training and service purposes
11. Abnormal sound (AV)-Main PCBA
1 NO
Put into AV cable completely? Insult AV cable tight
YES
YES
Change IC501
WAVEFORMS
C520,C521(audio in)
Copyright LG Electronics. Inc. All rights reserved. - 22 - LGE Internal Use Only
Only for training and service purposes
12. Abnormal sound (HDMI)-Main PCBA
YES
YES
YES
YES
YES
Check Line between JK203 and IC501
6 Is wavef orm at 1,3,4,6,7,9pin NO
is open or short, Another is
Of JK203? Change HDMI cable
YES
Change IC501
Copyright LG Electronics. Inc. All rights reserved. - 23 - LGE Internal Use Only
Only for training and service purposes
Copyright
Module Module Module
Adaptor BLU BLU
2224 28
IR
ST_3.5V
KEY2
KEY1
Output
19V
P Dim
Inv. ON
Led_PWR
102 105 XXX 117 111 110 108
DT1641S
USB_5V
BLU_24V
TPS40210 IR/KEY
USB_DN
98
IC502 94 SPI_CLK USB_DP
95 99
IF_P
24Mhz
P_ST 3.5V
- 24 -
77 62 54 40
MP2315 10 11
41 30 18 100
Main_1.2V
MP20051 9 116 107 45 9 IF_AGC
M_3.3V 53 4 Tuner SDA
Q710 52 3 Tuner SCL
Main_1.8V 48
BLOCK DIAGRAM
50 TUNER
51 113 112 XXX 22,20,24, 27,35,36 37 38
B+
40 35 5
I2S_MCLK
S_AMP_19V 7 I2S_WS
32 19 HDMI OP-AMP +18V
8 I2S_SCK
31 20 SCL/SDA
9 x4 Gain
CVBS In
RGB or
33
COMPONENT In
(( LPF
30
NTP7514
Audio_SDA
21 10 11
LPF Audio_SCL
18
(( or M_3.3V
910
400
521
120
540
LV1
900
Option
800
801
200
510
301
A31
300
A2
Copyright LG Electronics. Inc. All rights reserved. - 25 - LGE Internal Use Only
Only for training and service purposes
EAX65643103
44A/45A/450A
[RD1]E-LUG
6B IR & LED C126
4.7uF 1
R120 R121 10V
R122 JP120
3.3K 3.3K
100
2
5B [RD1]C-SPRING KEY1
C121 JP121
ROUT R123
100
0.1uF
16V
3
42A
KEY2 P121
D121
20V
D120
C120 JP122 SMAW200-05
20V
4B [RD1]CONTACT 0.1uF
16V 4
JP123
1
EEP_SCL 5
6G [RD3]E-LUG JP127
5
9
C JP128
R126
10K B Q120 10
5G [RD3]C-SPRING LED_B MMBT3904(NXP)
JP129
RIN READY
R127
E
11
10K
100pF 50V
100pF 50V
D126 20V
20V
[RD3]CONTACT
READY
READY
C122
C123
4G 12
D127
13
5F [WH2]C-SPRING
LIN
JP108
5E [RD2]C-SPRING
COMPONENT
COMMON_R R130
100
COMPONENT
ZD105 R145 IR
SD05
[RD2]E-LUG-S
D123
75 C124
20V
JP130
7E ZD106
SD05 +3.5V_ST 1000pF
50V
COMPONENT
JP131
JP107
5D [BL]C-SPRING
COMPONENT
COMMON_B
COMPONENT C125 D124
ZD103 4.7uF
SD05 R146 5.6V
4C [GN/YL]CONTACT ZD104
75 10V
SD05
COMPONENT
5C [GN/YL]C-SPRING
6C [GN/YL]E-LUG
MODULE_HD MODULE_FHD MODULE_HD_18.5
P101
10031HR-30
LVDS P102
10031HR-30
P103
10031HR-30
12.12.19. ESD(Add zenerDiode) PANEL_VCC PANEL_VCC
JP111 JP112
1 1 1
2 2 2
3 3 3
JK101 33A/4050 INTERLACE MODE
4 4 4
PPJ234-03 AV_IN/OUT 22LB
Change Option Name.(22LN4300 -> 22LB)
5 5 -. TN FHD : PWM OUT(If not use : NC) 5
6E [YL]E-LUG R100 -. IPS FHD : Interlace(If not use : GND)
6 6 0 6
RXA3+
12.12.18 : ESD(Add to zener diode) 7 7 7
RXA3-
RXA3+
5E [YL]O-SPRING 8 8
RXA3+ 8
COMMON_VIN 9
RXACK+ 9
RXA3-
RXA3- 9
ZD101 RXACK+
R101 10 10 10
SD05 RXACK- RXACK+
4E [YL]CONTACT JP103 ZD102
75
11 11
RXACK-
11
SD05
RXA2+
RXACK-
12 12 12
RXA2+ RXA2+
RXA2-
13 13 13
5D [WH2]O-SPRING JP101
R106
RXA2- RXA2- RXA3+
10K C102
AUDIO_LIN 14 14
RXA1+
14
RXA3-
D103 R105 R107 15 15 15
20V 220K 12K 1000pF RXA1+ RXA1+
RXA1-
4C [RD2]CONTACT 50V 16
RXA1- 16
RXA1- 16
RXACK+
EMS Improve(12.12.28)
LIN READY -> 1000PF 17 17 17
RXACK-
RXA0+
18 18 18
RXA0+ RXA0+
5C [RD2]O-SPRING JP102
R103 19 19
RXA0-
19
RXA0- RXA0- RXA2+
10K C101
AUDIO_RIN 20 20
RXB3+
20
D102 R102 R104 1000pF RXB3-
RXB3+ RXA2-
20V 220K 12K 21 READY 21 21
7C [RD2]E-LUG-S 50V R110
10K RXBCK+
RXB3-
RIN 22
+3.3V_M 22
RXBCK-
RXBCK+ 22
RXA1+
23 23 23
To improve EMS S2a issue. C104
10uF R111
RXBCK- RXA1-
5B [WH1]O-SPRING JP104 2013.11.27 by BJ.KIM
R108
10V 24 10K 24 24
C103 1K MNT_LOUT 25 25
RXB2+
RXB2+ 25
RXA0+
D104 RXB2-
1000pF C B 26 26 26
[WH1]E-LUG-S
20V 50V
E MUTE_AOUT RXB1+
RXB2- RXA0-
7B R112
3.9K
POP NOISE 27 PANEL_VCC 27
RXB1+ 27
Q101 RXB1-
28 28 28
MMBT3904(NXP)
RXB1-
LOUT 29
JP110
29
RXB0+
29
4A [RD1]CONTACT RXB0-
RXB0+
30 30 30
READY RXB0-
C106 C112
To improve EMS S2a issue. 10uF 31 10uF 31 31
C105 1K MNT_ROUT
D105 1000pF C B
6A [RD1]E-LUG
20V 50V
E R113
POP
MUTE_AOUT
NOISE
3.9K
Q103
MMBT3904(NXP)
ROUT
Copyright 2014 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
EAX65643103
44A/45A/450A
75 COMPONENT
75 COMPONENT
75 COMPONENT
RGB HDMI2
R202-*1
R203-*1
R201-*1
JK201 EAH39491601 -> EAF61771401
2013.11.27 by BJ.KIM HDMI2
SPG09-DB-010 R231
1K
HDMI2
C
R230
91 RGB
91 RGB
10K
91 RGB
B Q230
HDMI1_HPD
R202
R203
MMBT3904(NXP)
R201
HDMI2
D201 E
D202
D203
RGB
RGB
RGB
+3.5V_ST
+5V_USB
10K
R235
2013.11.27 by BJ.KIM
HDMI1_DET
GND_2
HDMI2
SHIELD
D231
1 11
RGB
R214
READY
RED 20
D209
15
COMMON_R 19 HPD
COMPONENT HDMI2 HDMI2
GREEN_GND JP220
R214-*1
0 GND_G
18 +5V_POWER EAH39491601 -> EAF61771401 R232 R233
7 2013.11.27 by BJ.KIM 2.7K 2.7K
READY
R204
D248
DDC_DATA 33 17 DDC/CEC_GND
2 12 RGB JP204
GREEN JP221
R215
15
16 SDA HDMI1_SDA
BLUE_GND JP222
COMPONENT
R215-*1 GND_B
2013.05.30 CJ.LIM DSUB_G 15 SCL
JP205
HDMI1_SCL
8 0 14 NC
HDMI2
RGB D234 D233
D232
R205 EAH39491601 -> EAF61771401
H_SYNC 33 13 CEC READY RCLAMP0544T.TCT
6.5VTO11.0V
HDMI2 HDMI2 2013.11.27 by BJ.KIM
3 13 RGB
R216
DSUB_HSYNC
12 CLK- 1 8 R253
BLUE JP223 15
10
HDMI2
HDMI1_CK-
COMMON_B 11 CLK_SHIELD R254
NC JP224 2 7 10
HDMI2
9 COMPONENT
RGB 10
CLK+
R255
HDMI1_CK+
V_SYNC
R216-*1
0 R206 DATA0- 3 6 10
HDMI2
4 14
33
DSUB_VSYNC
9
R256
HDMI1_D0-
GND_1 8
DATA0_SHIELD 4 5 10
JP225
DATA0+ HDMI1_D0+
+3.3V_ST 7
SYNC_GND DATA1- 9 HDMI2
10 RGB
6
R257
JP226
DDC_CLOCK R207
33 R208
5
DATA1_SHIELD 1 8 10
HDMI2
5 15 JP227
10K
DATA1+ R258
HDMI1_D1-
DDC_GND 4 2 7 10
HDMI2
DSUB_DET 3 DATA2- R259
HDMI1_D1+
3 6 10
HDMI2
RGB C203 68pF
DATA2_SHIELD
HDMI1_D2-
RGB C204 68pF
RGB R212 22K
READY 2
R260
C201
1
DATA2+ 4 5 10
JP228
68pF
HDMI1_D2+
D205
D206
50V READY
16
D204
D207
D208
C202
SHILED 68pF
50V
D235 9
JK203 RCLAMP0544T.TCT
6.5VTO11.0V
RGB
RGB
RGB
HDMI2
1.RED
READY
2.GRN
3.BLU EAH39491601 -> EAF61771401
4.NC 2013.11.27 by BJ.KIM +5V_USB
5.ST-DET
7.GNC R210
8.B_GND 4.7K
9.G_GND DSUB_SCL
10.R_GND
11.GND DSUB_SDA
12.SDA R209 READY
4.7K READY
13.HSYNC C205 C206
14.VSYNC
15.SCL
18pF
50V
18pF
50V
HDMI1 HDMI1
R242
1K
HDMI1
C
R241 HDMI1
10K B Q240
HDMI2_HPD MMBT3904(NXP) +3.5V_ST To improve HDMI Detect speed.(OPT(HDMI1)->Apply)
2013.11.27 by BJ.KIM
E
+5V_USB
10K
R816
HDMI2_DET
READY
D246
SHIELD
HDMI1
20 D241
20V
19 HPD EAH39491601 -> EAF61771401
HDMI1 HDMI1
2013.11.27 by BJ.KIM
18 +5V_POWER R243 R244
2.7K 2.7K
D247
READY
17 DDC/CEC_GND
JP206
16 SDA HDMI2_SDA
15
SCL
HDMI1 HDMI1
HDMI2_SCL
14 NC JP207
D244 D242 D243
20V 20V
13 CEC READY RCLAMP0544T.TCT
6.5VTO11.0V
HDMI1
R245
12 CLK- 1 8
SIDE USB +5V_USB REAR USB +5V_USB 11 CLK_SHIELD
10
CLK+
2 7
10
HDMI1
R246
10
HDMI1
R247
HDMI2_CK-
HDMI2_CK+
Close to SIDE_USB Close to SIDE_USB DATA0- 3 6 10
HDMI1
SIDE_USB
REAR_USB 9
R248
HDMI2_D0-
SIDE_USB C221
JK205 REAR_USB
C222 8
DATA0_SHIELD 4 5 10
3AU04S-305-ZC-(LG) 22uF US-04A-VSD 22uF DATA0+ HDMI2_D0+
JK202 6.3V 6.3V 7
DATA1- 9 HDMI1
6
R249
1 1 8
1
DATA1_SHIELD 10
HDMI1
5
HDMI2_D1-
USB DOWN STREAM
JP208 JP250
DATA1+ R250
2 4 2 7 10
HDMI1
2
SIDE_USB_DN REAR_USB_DN
JP209 JP251 3 DATA2- R251
HDMI2_D1+
DATA2_SHIELD
3 6 10
HDMI1
3 HDMI2_D2-
3
SIDE_USB_DP REAR_USB_DP 2
JP210 READY JP252 READY R252
ZD220
READY
ZD221 ZD222
READY
ZD223 1
DATA2+ 4 5 10
JP211
4
JP253 HDMI2_D2+
4
D245 9
5
Copyright 2014 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
EAX65643103
44A/45A/450A
SW_RESET R310 100
C320
1000pF
50V
+19V
50V
I2S_MCLK R304 100
4.7K
22000pF
C319
+3.3V_M TAIYO YUDEN
R311
READY L303-*1
C318 C317 C348 10.0uH
C321 0.1uF 10uF 10uF
10uF 25V 25V 25V
[EP]GND
10V
ABCO
VDD_IO
GND_IO
PGND1A
PVDD1A
PVDD1B
R313 R314 SPK_L+
L303
CLK_I
RESET
BST1A
OUT1A
12 12
10uH
To improve CST issue.(X5R -> X7R) R322
C330
EAE31360401->EAE52158501 0.1uF
2013.11.27 C325 50V 4.7K
AD
390pF
50V
C329
C326 ABCO 0.47uF
50V
SPEAKER_L
390pF
50V C331 R323
L304
40
39
38
37
36
35
34
33
32
31
0.1uF
10uH 50V 4.7K
R315 R316 SPK_L-
NC_1 1 30 OUT1B 12 12
TAIYO YUDEN
C314 SPK_L-
I2S_SDO
R301 100 SDATA 7 24 VDR2 1uF SPK_L- JP302
3
AUAMP_SDA
R305 100 SDA 10 21 OUT2A 50V .
11
12
13
14
15
16
17
18
19
20
R306 100 SMAW250-H04R
AUAMP_SCL
20130914 cjlim P301
R308 R309 TAIYO YUDEN
4.7K 4.7K READY -> APPLY C305 C306
33pF 33pF
L305-*1
SCL
FAULT
MONITOR_0
MONITOR_1
MONITOR_2
BST2B
PGND2B
OUT2B
PVDD2B
+3.3V_M 50V 50V PVDD2A 10.0uH
+19V
R317 R318 ABCO SPK_R+
12 12 L305
10uH C334
0.1uF R324
50V 4.7K
READY C327
390pF
C309
0.1uF
C310
10uF
C349
10uF
50V C333 SPEAKER_R
25V 0.47uF
25V 25V 50V
C328
390pF ABCO C335 R325
50V 0.1uF 4.7K
C308 50V
22000pF R319 R320 L306
12 12 10uH
50V
SPK_R-
TAIYO YUDEN
L306-*1
10.0uH
POWER_DET
C341
0.1uF
25V Q341
MMBT3904(NXP)
C
E
B R342 1K 1 OUT1 OUT4 14
C342
0.0068uF R343 10K
MNT_LOUT 50V
R341
4.7K C343 33pF 50V 2 INPUT1- INPUT4- 13
R344
6.8K
MNT_L_AMP
R345 5.6K 3 INPUT1+ INPUT4+ 12
+18V
4 VCC GND 11
C344
0.1uF
25V
MNT_R_AMP
R346 5.6K 5 INPUT2+ INPUT3+ 10
+18V C345 33pF 50V
Copyright 2014 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
TBD
44A/45A/450A
NTSC IF
TU402
TDSS-H701F +1.8V_M
READY
L402
BLM18PG121SN1D
NTSC
NTSC C409
C408 10uF
0.1uF 10V
16V
NC_1 MULTI_TUNER
1 +3.3V_TU
TU401 +3.3V_M
NC_2
2 TDJH-G101D Near the pin
L401
BLM18PG121SN1D
B1[+3.3V]
SDA 1 READY
R404
4 NC_1
To set multi option for NTSC
2013.11.27 by BJ.KIM
READY
R403
100K
2 100 +3.3V_TU
+B1[3.3V] TUNER_RESET
NTSC READY
5 IF_AGC R412
PAL 100
R412-*1
1K C401
0.1uF
3 IF_AGC 16V
C410
NC_3 SCL
0.1uF
16Vshould be guarded by ground
R407
1K
R408
1K
6 4 C402
R415 33
C406 TUNER_SCL
20pF 20pF
NC_4 SDA 50V
R416 33
50V
READY
7 5 C403 C407 TUNER_SDA
NTSC 20pF 20pF
PAL
IF[P] R413
R413-*1
33 50V 50V
NC_5 6 10 READY
IF_P
8 IF[N] PAL
R414
NTSC
R414-*1
33
10
7 IF_N
IF_AGC
9 NC_2 Close to the tuner
10 9
DIF[N]
11
A1 B1
A1 B1
B1 A1 47
B1 A1
SHIELD
12
SHIELD
READY
0 R402
READY
Copyright 2014 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
TBD
AUAMP_SCL
AUAMP_SDA
BLU_CURRENT_CTL
HDMI1_SDA
HDMI1_D0+
HDMI1_D0-
HDMI1_CK+
HDMI1_HPD
SW_RESET
HDMI1_CK-
HDMI1_D1+
HDMI1_D1-
+3.3V_ST
*H/W OPTION
MUTE_AOUT
HW_RESET
I2S_MCLK
HD FHD
IR
44A/45A/450A
LED_B
HW_OPT LOW HIGH
MSTAR Vcc
PWM_DIM
DSUB_SDA
DSUB_SCL
+1.8V_M
2.2uF
READY
C552
R519
4.7K +3.3V_M
GPIO69/I2S_OUT_MCK
KEY2
10K
KEY1
R535 1K
FHD
READY
R518 R550
R545
C549 R540 R537 R536 4.7K +1.2V_VDDC ST 1.26V
100 0.1uF 1K 22 C501
22
R531
100 10uF
HDMI2
HW_OPT1
33
C553 10V
R528
0.1uF R542 R541 HD
SAR3/GPIO72
SAR2/GPIO73
SAR1/GPIO74
SAR0/GPIO75
PWM1/GPIO25
PWM0/GPIO26
100 100 R551
AVDD_DDR_2
R534 4.7K
R546
HOTPLUG_D
C501 X5R(EAE31360401) -> X7R(EAE52158501)
100 1K
DDCDD_DA
To improve CST Issue
2013.11.27 by BJ.Kim
RXCKP_D
RXCKN_D
HWRESET
DDCA_DA
DDCA_CK
TESTPIN
R533
RX1P_D
RX1N_D
RX0P_D
RX0N_D
GPIO70
GPIO68
GPIO67
0
[EP]
IRIN
+1.8V_M DDR 1.8V
GND
CEC
C503
22uF
6.3V
INV_ON
128
127
126
125
124
123
122
121
120
119
118
117
116
115
114
113
112
111
110
109
108
107
106
105
104
103
HDMI2 READY
R522 100
R500
33 DDCDD_CK 1 102 GPIO64 L502 ST 3.3V
HDMI1_SCL +3.5V_ST +3.3V_ST
BLM18PG121SN1D
RX2N_D 2 101 GPIO63 +3.3V_ST C504
HDMI1_D2-
THERMAL C548
10uF
10V
RX2P_D 3 100 AVDD_MOD_4 0.1uF SIDE_USB
HDMI1_D2+ 129 R552 0
SIDE_USB_DP
HOTPLUG_A 4 99 USB0_DP C501 X5R(EAE31360401) -> X7R(EAE52158501)
HDMI2_HPD REAR_USB_DP To improve CST Issue
REAR_USB
RXCKN_A 5 98 USB0_DM R553 0 2013.11.27 by BJ.Kim
HDMI2_CK- SIDE_USB_DN
SIDE_USB
RXCKP_A 6 97 SPI_CZ R554 0
REAR_USB_DN
HDMI2_CK+ SPI_CZ
REAR_USB
RX0N_A 7 96 SPI_DO R555 0
HDMI2_D0- SPI_DO
RX0P_A 8 95 SPI_DI
HDMI2_D0+ SPI_DI
AVDD_MOD_1 9 94 SPI_CK
+3.3V_ST SPI_CLK
C505
0.1uF
RX1N_A 10 93 PWM3/GPIO25 FLASH_WP
IC503-*1
BR24G256FJ-3
IC503-*2
AT24C256C-SSHL-T
HDMI2_D1-
HDMI2_D1+
R505
RX1P_A 11 IC501 92 PWM2/GPIO24 R549 READY
33 EEPROM(256K)Renesas
IC503
A0
A1
1
2
8
7
VCC
WP
A0
A1
1
2
8
7
VCC
WP
HDMI2_D2-
HDMI2_D2+
RX2P_A
13
14
LGE6841 (ATV_13) 90
89 GPIO2
HDMI1_DET
POWER_SW
A0
1 8
VCC
C572
Rohm Atmel
R824 A1 WP 0.1uF R569 R577
33 DDCDA_CK 15 88 GPIO3 2 7
16V 4.7K 4.7K
HDMI2_SCL PANEL_ON
HDMI1 R527
ARC 16 87 GPIO4 10K A2 SCL
+1.2V_VDDC HW_OPT1
3 6
EEP_SCL
C506
0.1uF VDD 17 86 GPIO5 R529 100 VSS SDA
DSUB_DET
+3.3V_ST C507 R526
4 5
EEP_SDA
C512
4.7uF 0.1uF AVDD3P3_ADC 18 85 GPIO6 33 C573 C574
22pF
10V 22pF
EEP_SDA READY
R525 READY
HSYNC1 19 84 GPIO7 33
DSUB_HSYNC RGB/COMPONENT C508 EEP_SCL
R501 R516
33 0.047uF BIN1P 20 83 INT/GPIO65 100
COMMON_B POWER_DET
R523 C509 RGB/COMPONENT
470 1000pF SOGIN1 21 82 VDDC_2 C547 +1.2V_VDDC
0.1uF
DSUB_G
RGB/COMPONENT RGB/COMPONENT
GIN1P 22 81 LVB0M Add ROHM & ATMEL
R502
33
C510
0.047uF
RGB
R503
C511
0.047uF GIN1M LVB0P
RXB0- RXB0- SERIAL FLASH(8MB) 2013.11.27 by BJ.KIM
COMPONENT
RGB/COMPONENT RGB/COMPONENT
75
23 80 RXB0+
RXB0+
R515
0
RGB/COMPONENT COMPONENT
R503-*1 68 RIN1P 24 79 LVB1M
COMMON_R
R504 C550 RGB/COMPONENT RXB1- RXB1- +3.5V_ST
33 0.047uF VSYNC1 25 78 LVB1P FLASH_MXIC
DSUB_VSYNC RXB1+ IC502-*1
RXB1+
COMMON_VIN CVBS1 26 77 AVDD_MOD_3 MX25L6406EM2I-12G
R506
+3.3V_ST CS
1 8
VCC
C513
33 0.047uF CVBS0 27 76 LVB2M C546
0.1uF FLASH_WINBOND
SO/SIO1
2 7
HOLD
RXB2-
RXB2- WP SCLK
68 0.047uF
CVBSOUT1 LVBCKM
R581
10K
29 74 RXBCK-
RXBCK- R571 CS VCC
+3.3V_ST C515 AVDD_AU33 LVBCKP SPI_CZ 1 8
0.1uF 30 73 RXBCK+
100 C575
RXBCK+ 0.1uF
L506 AUREF 31 72 LVB3M SPI_DO
R572 DO[IO1]
2 7
%HOLD[IO3]
16V
C516 C517 RXB3-
RXB3- 100
120-ohm
10uF
16V
0.1uF VAG 32 71 LVB3P R576 WP[IO2] CLK R574
RXB3+ FLASH_WP 3 6 SPI_CLK
RXB3+ 100 100
LINEIN_L1 33 70 LVB4M
GND DI[IO0] R575
4 5 SPI_DI
LINEIN_R1 34 69 LVB4P 100
C576
C520 2.2uF LINEIN_L3 35 68 LVA0M 0.1uF
AUDIO_LIN
RXA0- RXA0- 16V
READY
C522 R510 C521 2.2uF LINEIN_R3 36 67 LVA0P
220pF 220K AUDIO_RIN
RXA0+ RXA0+
R508
100 LINEOUTL3 37 66 LVA1M
MNT_L_AMP RXA1-
RXA1-
LINEOUTR3 38 65 LVA1P
MNT_R_AMP RXA1+
R509 RXA1+
100
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
C523 R511
220pF 220K
+3.5V_ST H/W RESET
XTALO
XTALI
AVDD3P3_DMPLL
AVDD3P3_DADC
VIFP
VIFM
IFAGC
VSS
AVDD_DDR
GPIO55/I2S_OUT_WS
GPIO56
GPIO57/I2S_OUT_BCK
GPIO58/I2S_OUT_SD
GPIO60
GPIO61
VDDP
VDDC_1
LVA4P
LVA4M
LVA3P
LVA3M
LVACLKP
LVACLKM
AVDD_MOD_2
LVA2P
LVA2M
IC504 R561
JP501
JP502
JP503
JP504
APX803D29 10K
GND
33
R520
33
R521
RXACK-
1M 470
RXACK+
RXA2+
RXA3+
RXA3-
RXA2-
C542 C560
NTSC
NTSC
0.1uF 0.1uF
+3.3V_ST
R513-*1
R514-*1
4.7uF
24MHz 4.7uF
R513
C562
R514 R517 +1.8V_M
10V
100 10V
100 10K R564
0
I2S_SCK
I2S_SDO
RXACK-
0
RXA3+
RXA3-
RXA2-
TUNER_RESET
RXA2+
HW_RESET
RXACK+
R513,R514 : 0 ohm
R524
C531 C534 C535
TUNER_SCL
C530
TUNER_SDA
+3.3V_M 0 C563
R563
62K
15pF 15pF 2013.11.27 by BJ.KIM 0.1uF READY 0.1uF 0.1uF
C551 16V
220pF
50V
PAL PAL C541
C536 C537 0.022uF
33pF 33pF 16V
C544 C545
L521 0.1uF
+1.2V_VDDC
2013.11.27 by BJ.KIM
Close to MSTAR IF_AGC
+3.3V_ST
IF_P
IF_N
Copyright 2014 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
TBD
44A/45A/450A
+5V_USB
+19V
BLU_ON
DRIVER DRIVER
BOOST L601 D602
R627 33UH BR210
0
READY R602
R601 3K R604 DRIVER DRIVER 100V
10K 1K C606 C607
DRIVER 10uF 10uF
C 1% DRIVER 25V 25V
R603 R605
C601
10K B Q601 100K
1000pF
INV_ON MMBT3904(NXP)
1%
50V
EMI Improve
DRIVER
E 0-> 3.3ohm(12.12.25)
IC601 3.3-> 5.6ohm(12.12.25)
DT1641AS [EP]GND
D
DRIVER DRIVER
VOUT R620 Q602
EN VIN 5.6 G AOD478
1 24
THERMAL
DRIVER S
R606 DRIVER
25
560K OVP VREF C614
2 23
1uF
1% DRIVER DRIVER
C602 25V
R607
1000pF NC_1 CS
27K 3 22
1% 50V
R618
PGND_1 NDRV 0.1
DRIVER 4 21
R608 1%
100 DRIVER DRIVER
PWM_DIM READY
READY PGND_2
5 20
RSS
DRIVER
R616 R617
C603
R609 50V 240K 1% 10K 1% DRIVER
100K 100pF C605
PDIM COMP
6 19
READY DRIVER DRIVER 4700pF
R610 DRIVER 50V
100K RISET RT R613 R614
BLU_CURRENT_CTL 7 18 R615
39K 1% 1.5K 1% 1.5K 1% DRIVER
LS8 LS1 C604
HD_24/FHD_22 8 17 0.047uF
18.5_AUO 18.5_BOE 18.5_CMI FHD_22_HEESUNG/FHD_24 R611 25V
R611-*4 R611-*3 R611-*2 R611-*1 680
2.7K 1.8K 2.7K 0 LS7 LS2
1% 1% HD_24/FHD_22 9 16
18.5_AUO 18.5_CMI FHD_22_HEESUNG/FHD_24 R612
18.5_BOE R612-*2 R612-*1 20K
R612-*4 R612-*3 39K
33K 39K 36K LS6 LS3
1% 1% 10 15
LS5 LS4
Add BLU Current Option 11 14
2013.01.05
NC_2 LGND
12 13
VA600
VA601
VA603
VA604
VA605
VA606
VA602
VA607
READY
READY
READY
READY
READY
READY
READY
READY
JP601 JP603 JP605
VOUT
2CH/4CH
JP608
R624
0
2CH/4CH
05002HR-H12J05
12507WR-06L
12
11
10
1
2CH/4CH
6
P601
8CH
13
P602
7
Copyright 2014 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
TBD
44A/45A/450A
19V TO ST3.3V DCDC CONVERTER
+19V
IC701
MP2315GJ
R702
100K
** 3.5V_ST -> 1.26V VDDC
R701 R705 V0 = 0.8*(1+(R2/R1))
JK700
JP701 47K AAM
1 8
FB 33K +3.5V_ST IC704
KJA-DC-1-0032 AP7173-SPG-13 HF(DIODES)
+3.5V_ST +1.2V_VDDC OUT:1.26V
4 IN VCC [EP]
4 2 NEW 7
L702
10uH
2 2 C701
68uF
C703
10uF
25V
C704
0.1uF
SW
3 3A 6
EN/SYNC IN
1 8
OUT
THERMAL
35V 25V
C706 R706
ZD702
1 GND BST C707 C708 C709 2013.08.07 PG FB R1
9
1 20130528 cJ.LIM 0.1uF
5V
4 5 10uF 10uF 0.1uF 5.1K 5.6B->5V 2 7
25V 25V C742
R704 10V 10V READY->APPLY 1%
R703 1% 10uF
20K 1% R740
68 R707 VCC SS R741 10V
3 6 2.7K
27K
4.7K
JP702 C705 C746
X5R(EAE31360401) -> X7R(EAE52158501)
1% R744 560pF X5R(EAE31360401) -> X7R(EAE52158501)
0.1uF 10K EN GND 50V
50V To improve CST Issue. 4 5 To improve CST Issue.
2013.11.27 by BJ.KIM 2013.11.27 by BJ.KIM
C740
R708 10uF
10K 10V
1%
X5R(EAE31360401) -> X7R(EAE52158501)
To improve CST Issue.
2013.11.27 by BJ.KIM
470
READY READY +18V
READY
R715 C714
18V
Q712
AO3407A
READY READY
R713
READY
5.6K
R710 C
10K
B
+3.3V_M
READY
R716
Q713
E MMBT3904(NXP)
READY
** +3.5V_ST -> 3.3V_M
7.5K
+3.5V_ST
Q710
AO3435
D
+3.3V_M
IC702 READY
C724
BOOST_EN
MP2315GJ 0.47uF
16V C
R747
10K B Q711
R720 R724
47K AAM FB 33K POWER_SW MMBT3904(NXP)
1 8
L720 E
10uH
IN VCC
+19V 2 NEW 7 P_12V
ZD701
PANEL_12V
3A
READY
C727
15V
D
READY 25V R726 FET Multi_DMP2130L_DIODE
R722 100K Q720-*1
R721 20K 1% PANEL_5V
68 DMP2130L
R725-*1
G
47K
** Switch Panel-Vcc
D
C722 PANEL_12V 1%
R727 FET Multi_A03407B_AOS
0.1uF PANEL_5V
10K Q720-*3
50V 1% R726-*1
G
33K AO3407B
1%
P_12V
D
FET Multi_A03407A_AOS
PANEL_5V Q720 PANEL_VCC
R727-*1
G
15K AO3407A
1%
D
PANEL_12V C761 READY
0.1uF R765 R766
R767 PANEL_12V 3.3K 4.7K
24K C760 16V
R761
G
Q722 39K 4.7uF
C MMBT3904(NXP) 25V
PANEL_5V
R767-*1 B PANEL_5V
R771 2K PANEL_12V R761-*1 C760 X5R(EAE58111501) -> X7R(EAE62772301)
19V TO USB 5V DCDC CONVERTER 20130821 20K
D802 75K To improve CST Issue.
E BAT54C 2013.11.27 by BJ.KIM
IC709 C777 +3.3V_M A2
MP2315GJ 1uF C
2013.08.09 READY 10V
APPLY -> READY A1
DCM -> CCM R770 R774
47K AAM FB 33K PANEL_12V
1 8 R762
L770 PANEL_5V 39K
PANEL_5V
+19V IN VCC
10uH R768
0 R762-*1
2 NEW 7
+5V_USB 12K
C770 C771 SW
3A EN/SYNC C774 C775 C776 R775
ZD700
3 6 0.1uF C
5.6B
1%
GND BST
C773 PANEL_ON
20130528 cJ.LIM 0.1uF R776 Q721
4 5 READY 25V 33K E MMBT3904(NXP)
R773
R772 20K 1%
68
C772 R777
0.1uF 15K
50V
1%
Copyright 2014 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes
TBD
44A/45A/450A
22/26
P801
27.5
+24V_BLU SM14B-SRSS-TB P802
JP801 20022WR-14A00
24V 1
1
24V 2
+19V
2
BOOST BOOST +24V_BLU 24V 3
L801 D801
10uH BR210 3
24V 4
100V
BOOST READY
C802 C803 BOOST 4
BOOST BOOST READY
C804 BOOST BOOST
10uF 0.1uF R812 R813 24V
100pF 220K 30K C811 C814 C815 5
25V 25V
68uF 1uF 1uF
5
50V 35V 50V 50V
BOOST GND
BOOST BOOST C816 6
IC801 R814 270pF
TPS40210DGQR [EP] 10 50V 6
GND
7
RC VDD 7
1 10
GND 8
BOOST
THERMAL
BOOST
R801 C805
8
11
10K 0.22uF SS BP
2 9
D GND 9
BOOST BOOST BOOST
16V
R802 R811 Q801
1K DIS/EN GDRV 5.6 9
3 8 G AOD478
BOOST_EN GND 10
BOOST S
R810 JP802 READY
COMP ISNS 1K R820 10
4 7 100 ERROR_OUT 11
BOOST READY
BOOST C809 C810 BLU_ON
BOOST
READY
BOOST
R808
R809
0.1
READY
0.1uF
R821
R822 NC
12.07.03 To improve backlight blinking 4.7K 25V 13
BOOST JP804
BOOST R807
0
C1103 47pF->2200pF 13
R805 51K
C1105 47pF->Apply PWN_DIM
R1103 18K->470K PWM_DIM 14
470K
BOOST 14
R806 READY 15
1.5K C820
1uF 15
GND
10V
Copyright 2014 LG Electronics. Inc. All rights reserved. LGE Internal Use Only
Only for training and service purposes