Beruflich Dokumente
Kultur Dokumente
0
4
3
31
23
2
2
33
29
21010101
2s
4
4
Yes
5
10
60
60
60
60
No
Parameter Name Object Name HW setting range HW default value Ericsson
NetWork Optimization Index of Original Cell Basic Parameters 0~2048 cell specific
Name of Original Cell Basic Parameters A string of 32 characters cell specific
Allow Dynamic Voltage Adjustment Basic Parameters Yes,No No Yes
Allow Dynamic Shutdown of TRX Power Amplifier Basic Parameters Yes,No No Yes
UL DTX Basic Parameters May use, Shall use, Shall use Shall Use
PT(s) Idle Mode 0-30 (20s to 620s) 3 0 0
AMR ACS(H) Call Control 6.70 Kbps, 5.90 Kbp 01101 010101
Qsearch C Initial Call Control Use Qsearch_I, Alw Use Qsearch_I Use Qsearch_I
Special Access Control Class Call Control Level11 Forbidden, 00000 00000
Common Access Control Class Call Control Level0 Forbidden, L 0000000000 0000000000
MS MAX Retrans Call Control 1247 2 Times 4 Times
TRX Aiding Function Control Call Control TRX Aiding Not All Allowed & Recover Allowed & Recove
Preference for 2G
Cell, Preference for Preference for 2G Preference for
TDD Inter-RAT HO Preference Handover Control 3G Cell, Preference Cell By Threshold 2G Cell By
for 2G By Threshold
Threshold
Load HO of OL Subcell to UL Subcell Enabled Handover Control Yes,No Yes Cell specific
Load HO From UL Subcell to OL Subcell Allowed Handover Control Yes,NO No Cell specific
En Iuo Out Cell Serious OverLoad Thred Handover Control 0100 90 90/cell specific
En Iuo Out Cell Low Load Thred Handover Control 0100 20 cell specific
Incoming-to-BSC HO Optimum Layer Handover Control Overlaid Subcell, Underlaid Subcell, No Underlaid Subcell
Pref. Subcell in HO of Intra-BSC Handover Control System OptimizationThe default value is System Optimizat
Assign Optimum Layer Handover Control System OptimizationUnderlaid Subcell: System Optimizat
RX_LEV for UO HO Allowed Handover Control Yes, No The default value is Yes
Sent Freq.of preprocessed MR Handover Control Do not Report, Twic Twice every second Once every secon
HwIII Down Link Power Control Adjust Period Power Control 0255 3 3
Power Control Algorithm Switch Power Control HWII Power Contrl, HWII Power Contrl HWIII Power Cont
Busy Threshold of TCH Traffic in Overlaid Subcell Channel Management0-100 50 cell specific
AMR TCH/H Prior Cell Load Threshold Channel Management099 40 cell specific
MAX Paging Message Number 0f Cell In Period Other Property 160 220
cell specific
cell specific
No
Yes
63
Yes
A5/0A5/2
Yes
Yes
Yes
No
Yes
Shall Use
0
No
No
Yes
6dB
50
2 Multiframe Peri
1
11111111
No
50
Yes
0
15
63
31
23
15
63
31
23
010101
25
17
12
28
19
15
10010101
1
Different Band
No
No
No
No
No
Yes
0
0
15
+0dB
No
Yes
15
RSCP
Use Qsearch_I
15
Yes
Yes
20
No
00000
0000000000
4 Times
No
34
29
23
No
60
60
200
150
50
50
60
-110
180
101111
20
24
20
24
70
No
16
20
45
No
50
25
Preference for 2G
68
63
10
35
50
50
90
5
5
25
30
10
No
No
10
10
90
80
No
Yes
50
No
35
50
25
Preference for 2G
35
25
60
50
90/cell specific
cell specific
cell specific
10
40
15
Yes
cell specific
cell specific
Underlaid Subcell
System Optimizati
61
No
61
cell specific
System Optimizati
61 / cell specific d
60
5
cell specific
10
No
No
Yes
Yes
Yes
80
25
20
15
10
25
70
90
10
60
60
60
60
40
41
42
43
44
45
46
47
48
49
50
60
55
No
10
10
10
10
10
10
10
10
60
60
61
Open
255
10
10
10
63
cell specific
cell specific
63
4
3
16
Yes
No
No
No
Yes
No
2
2
Close
3
4
NO
10
20
4
5
Yes
8
0
2
30
No
2
3
3
3
2
cell specific
10
Yes
Yes
Yes
Yes
Yes
No
Yes
No
No
No
No
No
Yes
6
13
13
12
12
14
14
14
14
18
18
13
13
12
12
14
14
14
14
18
18
16
25
33
3
18
25
Yes
16
10
Yes
5
5
25
45
18
25
95
Yes
cell specific
cell specific
Close
Close
80
80
60
cell specific
Yes
2
30
30
45
30
35
Yes
Yes
Yes
Yes
Yes
No
Not Support
Quality Preferred
Yes
60
cell specific
cell specific
26000
34000
10000
10
15000
1000
30000
25000
30000
5000
10000
10000
5000
3000
220
180
Forced turn-on
Interference Band
Yes
No
No
Yes
Yes
Maximum/Mean V
1
1
No
15
Yes
Yes
Yes
360
360
5000
15
100
15
10
36671
NO
2
65535
20
48
90
98
104
108
115
90
Yes
0001110110
StartUp
Not Report
Invalid
10
3
20
Not Support
No handover betwe
16
6
Not Support
Not Support
Not Support
MCS6
UNFIXED
MCS2
UNFIXED
8
LA
20
10
20
10
5
5
CS2
UNFIXED
20
10
20
10
5
5
CS1
UNFIXED
30
2
No preempt of CC
30
Only convert at UL
80
70
cell specific
cell specific
cell specific
Report the frequenc
-110dB
2
2
2
NoExclusive
Permit
2dB
10sec
Yes
0
c31standard
2dB
No
No
6
16
14
13
12
20
20
7
7
7
7
0
1
4
1
0.96sec
15.36sec
0.24sec
-2db
10sec
10dB
60sec
type1
1
1
em0
Yes
Yes
Area specific
Packet access of le
No
nc0
12
4
2
10
Four access pulses
8bit
4
500ms
500ms
Network Operation
0.6
14
10
10
pdch
2
Parameter Description
This parameter determines the actual coverage area of a cell. When the BTS receives a CHANNEL REQUEST message or a
HANDOVER ACCESS message, it compares the TA with the value of this parameter to determine whether channel assignment or
handover is performed in this cell.
This parameter indicates the whether the directed retry on the TCH is allowed. If this parameter is set to Yes, the handover
procedure is used and the MS is handed over to the neighboring cell. Direct retry is an emergency measure for abnormal peak
traffic in the local wireless network. It is not a primary method of clearing traffic congestion. If direct retry is preformed frequently
in a local network, you must adjust the sector carrier configuration of the BTS and the network layout.
Yes: It indicates that the TCH is immediately assigned when the SDCCH has no available resource during the processing of access
request. No: It indicates that only the SDCCH can be assigned.
Cell Reselect Temporary Offset (TO) indicates the temporary correction of C2.This parameter functions only before the penalty time
of cell reselection expires
Additional Cell Reselectiom Param Indication:If ACS=0,Invalid in SySTEM INFO=3,but works in SYSTEM INFO=4 to tell SYTEM INFO
4.IF ACS=1,tells it means that the MS should obtain PI and other parameters for calculating C2 from other bytes of system
information 7 and 8.
If this parameter is reasonably configured, the number of handovers can be reduced and a better cell can be assigned to.When PT
is set to 31, it becomes more difficult for an MS to access a cell when CRO increases
Cell Reselection Parameter:Indicates whether to perform C2-Based Cell reselection.When PI=1 MS will calculate C2 from SYSTEM
INFO and perform Cell Reselection.If PI=0 then C1=C2,Cell-Reselection will be based on C1
CELL_RESELECT_HYSTERESIS,As MS does not responds to Paging messages during Location Update,too much Cell-Selection will
lead to Connection drop.If it too Low,Frequent Cell-Rselection will Occur causing Load on Signaling.Too High value can cause MS t o
"Forced Periodic Location Update".T3212
CAMPisoused
Olderforcell
Forced
evenLocation
when LAC Update
Area isofChanged
Every mobile in Cell-Coverage Area.Unit id 6
minutes.
PagingIfMutiFrame
any mobileperiod:Defines
failed to respond to Paging
Period message
for sending for a REQUEST
PAGING long time message
it will be for
considered
to same as "Off-Line",and if this
Paging-Subgroup,the mobileofcell-
number
Reselection,T3212 will Reset &paging
Network still Can`t find
sub-channels on aLocation of MS,So
specific paging it will be "OFF-Line" for a Long time.
channel.
.When MFR increases, the number of paging sub-channels increases, thus reducing the number of subscribers served by each
Number of CCCH Blocks used forsub-channel
paging Access GrantandChannel remaining
prolonging are usedwork
the average for Paging
time ofchannels.In each downlink non-combined
the MS battery.
SDCCH 51 frames
Network Colourmulti-frame there
Code that are are 9 different
Permitted,Sent in CCCH
System blocks and in the
Information typecombined
2&6,ThisBCCH/SDCCH
parameter can there are 3todifferent
be used make MS blocks
's
measurements on some adjacent cells optionally.Cells with NCC ranging in NCC permitted range will MS report Measurement
Reports
This Indicates whether a Cell Access is Barred or not. Together with CBQ it is used for determinig Priority of Cells.
It indicates the number of timeslots in an interval when an MS sends continuously multiple channel requests.Used to Reduce
Collision on RACH & to Increase Efficiency of RACH.
IMSI Attach?detach allowed:Detach,This is the Last message that MS Sends when it is Powered-Off,If set to No then System will
This
haveparameter
to wait forindicates
T3212 forthe half rate used
considering when
MS to a call is initially established.As
be "OFF-Line".IMSI AMR.ACSgenerated
Attach is First message (H) includes fourtocoding
by MS Informrates at most,
Network its
this parameter can only be given four values: 0, 1, 2, and 3. These four values correspond to low-to-high half rates in AMR ACS (H).
Presence
The AMRconditions:AMR
This parameter must meet the following Starting Mode (H)
DL should
Coding be within
Rate the(H)
adj.th2 AMR ACS (H).
< AMR DL Coding Rate adj.th3 (H) [AMR DL
Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2 (H) ] < [AMR DL Coding Rate adj.th3 (H) + AMR DL Coding Rate adj.hyst3
(H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2 (H) < AMR DL Coding Rate adj.th3 (H) [AMR DL
Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2 (H) ] < [AMR DL Coding Rate adj.th3 (H) + AMR DL Coding Rate adj.hyst3
(H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th1 (H) < AMR DL Coding Rate adj.th2 (H) [AMR DL
Coding Rate adj.th1 (H) + AMR DL Coding Rate adj.hyst1 (H) ] < [AMR DL Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2
(H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2 (H) < AMR DL Coding Rate adj.th3 (H) [AMR DL
Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2 (H) ] < [AMR DL Coding Rate adj.th3 (H) + AMR DL Coding Rate adj.hyst3
(H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2 (H) < AMR DL Coding Rate adj.th3 (H) [AMR DL
Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2 (H) ] < [AMR DL Coding Rate adj.th3 (H) + AMR DL Coding Rate adj.hyst3
(H)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th1 (H) < AMR DL Coding Rate adj.th2 (H) [AMR DL
Coding Rate adj.th1 (H) + AMR DL Coding Rate adj.hyst1 (H) ] < [AMR DL Coding Rate adj.th2 (H) + AMR DL Coding Rate adj.hyst2
(H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2 (H) < AMR UL Coding Rate adj.th3 (H) [AMR UL
Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H) ] < [AMR UL Coding Rate adj.th3 (H) + AMR UL Coding Rate adj.hyst3
(H)]
This parameter must meet the following conditions:AMR uL Coding Rate adj.th2 (H) < AMR uL Coding Rate adj.th3 (H) [AMR UL
Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H) ] < [AMR UL Coding Rate adj.th3 (H) + AMR UL Coding Rate adj.hyst3
(H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th1 (H) < AMR uL Coding Rate adj.th2 (H) [AMR UL
Coding Rate adj.th1 (H) + AMR UL Coding Rate adj.hyst1 (H) ] < [AMR UL Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2
(H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2 (H) < AMR UL Coding Rate adj.th3 (H) [AMR UL
Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H) ] < [AMR UL Coding Rate adj.th3 (H) + AMR UL Coding Rate adj.hyst3
(H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2 (H) < AMR UL Coding Rate adj.th3 (H) [AMR UL
Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2 (H) ] < [AMR UL Coding Rate adj.th3 (H) + AMR UL Coding Rate adj.hyst3
(H)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th1 (H) < AMR UL Coding Rate adj.th2 (H) [AMR UL
Coding Rate adj.th1 (H) + AMR UL Coding Rate adj.hyst1 (H) ] < [AMR UL Coding Rate adj.th2 (H) + AMR UL Coding Rate adj.hyst2
(H)]
4.75 Kbps-12.2 Kbps 12.2 Kbps, 10.2 Kbps, 7.95 Kbps, 7.40 Kbps, 6.70 Kbps, 5.90 Kbps, 5.15 Kbps, 4.75 Kbps,If only value is selscted
then AMR starting Mode(F) must be 0,If two are selected then AMR Starting Mode(F) must be 1.
This parameter must meet the following conditions:[ AMR DL Coding Rate adj.th2 (F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR
DL Coding Rate adj.th3 (F)+ AMR DL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR DL Coding Rate adj.th2 (F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR
DL Coding Rate adj.th3 (F)+ AMR DL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR DL Coding Rate adj.th1 (F) + AMR DL Coding Rate adj.hyst1 (F) ] < [AMR
DL Coding Rate adj.th2 (F)+ AMR DL Coding Rate adj.hyst2(F)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2(F) < AMR DL Coding Rate adj.th3(F) [ AMR DL
Coding Rate adj.th2(F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR DL Coding Rate adj.th3(F) + AMR DL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th2(F) < AMR DL Coding Rate adj.th3(F) [ AMR DL
Coding Rate adj.th2(F) + AMR DL Coding Rate adj.hyst2 (F) ] < [AMR DL Coding Rate adj.th3(F) + AMR DL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR DL Coding Rate adj.th1(F) < AMR DL Coding Rate adj.th2(F) [ AMR DL
Coding Rate adj.th1(F) + AMR DL Coding Rate adj.hyst1 (F) ] < [AMR DL Coding Rate adj.th2(F) + AMR DL Coding Rate adj.hyst2 (F)]
This parameter must meet the following conditions:[ AMR UL Coding Rate adj.th2 (F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR
UL Coding Rate adj.th3 (F)+ AMR UL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR UL Coding Rate adj.th2 (F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR
UL Coding Rate adj.th3 (F)+ AMR UL Coding Rate adj.hyst3(F)]
This parameter must meet the following conditions:[ AMR UL Coding Rate adj.th1 (F) + AMR UL Coding Rate adj.hyst1 (F) ] < [AMR
UL Coding Rate adj.th2 (F)+ AMR UL Coding Rate adj.hyst2(F)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2(F) < AMR UL Coding Rate adj.th3(F) [ AMR UL
Coding Rate adj.th2(F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR UL Coding Rate adj.th3(F) + AMR UL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th2(F) < AMR UL Coding Rate adj.th3(F) [ AMR UL
Coding Rate adj.th2(F) + AMR UL Coding Rate adj.hyst2 (F) ] < [AMR UL Coding Rate adj.th3(F) + AMR UL Coding Rate adj.hyst3 (F)]
This parameter must meet the following conditions:AMR UL Coding Rate adj.th1(F) < AMR UL Coding Rate adj.th2(F) [ AMR UL
Coding Rate adj.th1(F) + AMR UL Coding Rate adj.hyst1 (F) ] < [AMR UL Coding Rate adj.th2(F) + AMR UL Coding Rate adj.hyst2 (F)]
12.2 Kbps, 10.2 Kbps, 7.95 Kbps, 7.40 Kbps, 6.70 Kbps, 5.90 Kbps, 5.15 Kbps, 4.75 Kbps,Default is 11100100,
Indicates Max No. of Assignment Retry times.Valid only when TCH Assignment Retry is Enabled.
In normal Assignment proceedure,after receiving "Assignment Failure" message from MS,BSc does not Inform this to MSC
immediately.Instead it Re-Assigns Radio Channel & Re-Origenates assignment Proceedure.Option Different Band can cause
Assignment failure to occur again when Assignment Failure Occurs due to Interference or Faulty TRX
Whether to disable all users in a particular cell to receive messages in DL,but MS in call can receive messages in DL
This parameter is used to concurrently deliver the channel activation message and immediate assignment command message to
quicken
This parameter Whether
indicates to disable
the processing
whether all users
toofenable
signaling. in a particular
theThus cellTCHH
the response
function that the to send
speedisof messages in DL.
the network
adjusted is ensured.
according to Abis resources.
ThisThe
function is used inassigns
BSC preferably satellite transmission
TCHH to the MSmode. In satellite
according to the transmission
Abis resourcemode, the Immediate
load when Assignment
the Abis resources are Opt parameter
insufficient.
must be set to Yes to minimize the effect of the satellite transmission on time delay. In terrestrial transmission mode, the default
value
After this parameter is set to Yes, the BSC preferably of this
assigns parameter
TCHH is No.
to the MS if the Abis resource load exceeds the Flex Abis Prior
This parameter indicates whether the enhanced
Abis multi level
Load Threshold precedence
or Fix Abis Priorand
Abispreemption (eMLPP) function is allowed. The eMLPP
Load Threshold
means that the network is allowed to use different policies such as queuing, preemption, and direct retry according to the calls
with different priorities when the network resources are seized.
This parameter indicates whether the reassignment function is allowed.
This parameter indicates the reporting threshold for TDD cells.When the receive level of the TDD cell in the measurement report is
greater than the value of this parameter, the measurement report is valid.After the valid measurement report is filtered, the TDD
cell joins in the cell priority rank
This parameter indicates the reporting offset for TDD cells.When ranking the priority of a TDD cell, it is recommended to first add
the value of this parameter to the receive level of it in the measurement report.
This parameter indicates whether the reassignment function is allowed.
If this parameter is set to Yes, the BSC originates a second assignment when the BSC receives the Assignment Failure message. If
this parameter is set to Yes, it is good to raise the call completion rate of the MS. If there are a lot of MS assignment failures,
however, the BSC originates re-assignments for a lot of MSs. As a result, the BSC will experience more load.
The TDD cell can become a candidate cell only when the average receive level of the TDD cell is greater than the "FDD Q Offset" of
the serving cell.
This parameter indicates the reporting offset for 3G cells.When ranking the priority of a 3G cell, it is recommended to first add the
value of this parameter to the receive level of it in the measurement report.
This parameter indicates the report offset for 3G cells.
When ranking the priority of a 3G cell, it is recommended to first add the value of this parameter to the receive level of it in the
measurement report
This parameter indicates the reporting offset for DCS1800 cells.When ranking the priority of a GSM1800cell based on its frequency
band, it is recommended to first add the value of this parameter to the receive level of it in the measurement report
This parameter indicates the reporting offset for DCS1800 cells.When ranking the priority of a GSM1800cell based on its frequency
band, it is recommended to first add the value of this parameter to the receive level of it in the measurement report
This parameter indicates the reporting threshold for GSM900 cells.When ranking the priority of a GSM900 cell based on its
frequency band, it is recommended to first add the value of this parameter to the receive level of it in the measurement report
This parameter indicates the reporting offset for GSM900 cells.When ranking the priority of a GSM900 cell based on its frequency
band, it is recommended to first add the value of this parameter to the receive level of it in the measurement report.
This parameter indicates the threshold of level for cell reselection in connection mode.In connection mode, if the signal level in the
service cell is below (0-7) or above (8-15), the MS starts to search for 3G cells.
For example:If this parameter is set to 5 and the signal level in the service cell is below 5, the MS starts to search for 3G cells.
If this parameter is set to 10 and the signal level in the service cell is above 10, the MS starts to search for 3G cells
This parameter indicates the strength added to the received signal strength before the MS delivers the enhanced measurement
report
This parameter indicates whether a cell with invalid BISC is allowed in the measurement report
This parameter indicates whether the MS is allowed to search for a 3G cell when the BISC must be decoded
This parameter indicates one of the threshold of level for cell reselection in packet mode.In packet mode, if the signal level in the
This parameter indicatesservice
one of cell
the is
threshold of level
below (0-7) for the
or above reselection
(8-15), the MSofstarts
3G cells. Only when
to search for 3Gthe receive level of a 3G cell is
cells.
greater than FDD Qmin, the 3G cell can be one of the candidate cells for reselection.0= -20dB
For example:If this parameter is set to 5 and the signal level1=in-6dB
the service cell is below 5, the MS starts to search for 3G cells.
2=service
If this parameter is set to 10 and the signal level in the -18dB cell is above 10, the MS starts to search for 3G cells
3= -8dB
4= -16dB
5= -10dB
6= -14dB
This parameter indicates the number of UTRAN FDD cells 7= -12dB.
that a best cell list or a measurement report should include
Default value= -20dB
This parameter indicates the strength added to the received signal strength before the MS delivers the enhanced measurement
report
Only when the average receive level of a 3G cells is FDD Q Offset greater than that of the current service cell, the 3G cell can
become a candidate cell
This parameter indicates the threshold of level for cell reselection in connection mode befour the BTS receives the Qsearch C.
This parameter indicates the threshold of level for cell reselection in idle mode.In idle mode, if the signal level in the service cell is
below (0-7) or above (8-15), the MS starts to search for 3G cells.
If the
For system
example:Ifinformation indicates
this parameter "MBR",
is set the MS
to 5 and the reports the quantities
signal level of neighbor
in the service cells5,onthe
cell is below different frequency
MS starts to searchbands.When
for 3G cells.the
MS reports If thisthe quantity is
parameter ofset
neighbor cellsthe
to 10 and onsignal
the same
levelfrequency bandcell
in the service with the serving
is above cell,
10, the MSa starts
maximum of thefor
to search value of "Serving
3G cells
This parameter is used for the MS to report neighboring cell explanation
Band Reporting" of multiple bands. It is sent in the system messages 2ter
can be reported.
and 5ter.0: The MS reports the measurement These neighbor results
cellsofmust
six neighboring cells known
meet the following and permitted by the NCC at the bands with
requirements:
(1) The receive levels of the best
the signal regardless
neighbor cells must ofbethe band
higher at which
than the neighboring
"900 Reporting cell isorlocated.
Threshold" "1800 Reporting Threshold".
1: The MS reports the measurement result(2) ofThe
a neighboring
BSIC of thecell knowncells
neighbor and must
permitted by the NCC at each band with the best signal
be valid.
If a(the band
(3)
class The
3 MS serving
on thethe
signals current
ofDCS1800
the cell not
neighbor
band included).
cells
does must Thethe
be the
not receive MSoriginal
reports
strongest the measurement
among
power allcommand
the neighbor result
aftercellsofon
random thethe
neighboring
samethe
access, cell atthat
frequency
power the the
band
band. MS
serving the current cell in the redundant position. If the redundant position is still available, the
uses is the MS maximum transmit power level plus the power calculated from the power deviation. See protocol GSM 05.08 MS reports the measurement
results of other neighboring cells regardless of the bands at which the neighboring cells are located.2: The MS reports the
measurement results of two neighboring cells known and permitted by the NCC at each band with the best signal (the band serving
The
the MS doescell
current notnot
receive the original
included). The MS power
reportscommand after random
the measurement access.
result of theThis parametercell
neighboring indicates whether
at the band the power
serving deviation
the current cell
in the redundantisposition. added toIfthe
theclass 3 MS on
redundant the DCS1800
position band on the
is still available, the basis of the the
MS reports maximum MS transmit
measurement resultspower
of other neighboring
cells regardless of the bands at which the neighboring cells are located.
3: The MS reports the measurement results of three neighboring cells known and permitted by the NCC at each band with the best
signal (the band serving the current cell not included). The MS reports the measurement result of the neighboring cell at the band
serving the current cell in the redundant position. If the redundant position is still available, the MS reports the measurement
Use for
results of Dual-Band support cells
other neighboring MS to inform that
regardless Dualbands
of the Bandat
is which
Supported. Invalid for Single-Band
the neighboring MS
cells are located.
determins
When the time
the traffic of Disconnecting
volumes a call when
of multiple bands are theMS failsand
same to Decode
there isSAACH sentrequirement
no special by BTS,Once on
a dedicated
the band,channel
the MBRis(Multi
assigned a
Band
Timer Sisisset
Report) started. Every the
to 0. When timetraffic
BTS sussceesfully Decdes bands
volumes of multiple a SACCH,it Increments
are different andbythe2 MS
otherwise Decrement
is expected bya1.
to enter When
band this timer
preferentially,
the MBR (Multi Band Report) is set to 3. In other cases reaches 0 Radio
except theLink
first will
twobe Fail the MBR (Multi Band Report) is set to 1 or 2. For
cases,
For MSs whose access class is from 0 to 9, if the Emergent Callsee
details, Disable is set to No, emergency calls are allowed.For MSs whose
protocol
access class is from 11 to 15, emergency calls are not allowed only when the access control bit is set to 0 and the Emergent Call
Disable is set to Yes
This parameter is used for load control. It determines whether the users of special access class are allowed to access the network.
This parameter is used to control the load. It determines whether the users of common access class are allowed to access the
network
This parameter indicates the maximum times for sending Channel Request messages by the MS during an immediate assignment.
This parameter indicates the maximum number of retransmissions of the immediate assignment message. When this number is
reached, no retransmission is performed
Within the period specified by this parameter, the immediate assignment message can be dispatched and retransmitted.
Otherwise, the message cannot be dispatched or retransmitted
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the Max retransmit times of frame I on the FACCH (a full-rate channel).
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the Max retransmit times of frame I on the FACCH (a full-rate channel).
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the Max retransmit times of frame I on the SDCCH.
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the Max retransmit times of frame I on the SACCH
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the maximum retransmission times of frame I during the multi-frame
release.
When establishing LAPDm between the BTS and MS, the BTS sends frame I to the MS. When the MS detects error in the frame I,
the BTS should resend frame I.This parameter indicates the maximum retransmission times of frame I.
This parameter controls whether the BSC delivers the LAPDm N200 parameter to the BTS.
This parameter determines the expiry value of T200 when the SDCCH supports SAPI3 services.
This parameter determines the expiry value of T200 on the SACCH on the SDCCH
This parameter determines the expiry value of T200 on the SACCH over the Um interface when the TCH supports SAPI3 services
This parameter determines the expiry value of T200 on the SACCH over the Um interface when the TCH supports SAPI0 services
This parameter determines the expiry value of T200 on the FACCH or full-rate channel over the Um interface
This parameter determines the expiry value of T200 on the FACCH or full-rate channel over the Um interface
This parameter determines the expiry value of timer T200 on the SDCCH over the Um interface,T200 Prevents Dead-Lock on Data
Link Layer of Um Interface.two Entities use Acknowlege & Retransmission method. Whenever any one entity sends any message it
This parameter
shouldindicates which speech version is supported.
have acknowlegment,Otherwise It consists
T200 will be Expired. of six bits.
Theissixmin
This bits, fromofthe
Level most
RACH significant
upon which itone
willto
bethe least significant
accepted one, each
bythe network.If bit is
level indicates
less thanwhether thethen
this thrsh BSC RACH
supports
willthe following
be disgarded.
TRX Aiding Not Allowed indicates speech
thatversions:
the TRX aiding function is not allowed.
the system can determine whether the received signal is the random access signal of the MS through the correlation of training
Allowed and Recover Forbidden indicates that the
sequence TRX
TSC Half-rate
(41aiding
bits) and version
function 3
is allowed
can calculate butTAswitchback
the value. is forbidden after the faulty TRX is
recovered.
Half-rate version 2
Allowed and Recover Immediately indicates that the TRX aiding function is allowed and immediate switchback is allowed after the
Half-rate
faulty TRX isversion 1
recovered.
Allowed and Recover When Check Res indicates that the Full-rate version
TRX aiding 3
function is allowed but immediate switchback is forbidden
after the faulty TRX is recovered. The switchback is not performed until the resources are checked in the early morning.
Full-rate
Indicates RLT ofversion 2, Rate
AMR Half
Full-rate version 1.
Indicates RLT of AMR FULL Rate
If the value of one bit is 1, it indicates that the BSC supports the corresponding speech version. If the value of one bit is 0, however,
it indicates that the BSC does not support the corresponding speech version.
Indicates SACCH MultiFrame of AMR Half Rate
For example, if the parameter is set to 001011, infer that full-rate version 1, full-rate version 2, and half-rate version 1 are
supported.
Indicates SACCH MultiFrame of AMR FULL Rate
When target cells are selected during direct retry, only the cells whose loads are smaller than or equal to the Directed Retry Load
Access Threshold are selected as candidate target cells
RACH busy state. When the receive level of the random access burst timeslot is greater than this threshold, the BTS considers that
the timeslot is busy. In the BTS3X, this parameter only indicates whether the timeslot is busy. The threshold setting does not affect
the normal access of the MS.
In the BTS2X version (BTS24 not included), this parameter indicates the level threshold for the system to determine MS random
access. When the receive level of the random access burst timeslot is greater than this threshold and the access demodulation is
successful, the BTS considers that the timeslot is busy and determines whether the RACH access is valid based on the parameter
When
RandomtheAccess
Assignment Cell Load Judge
Error Threshold. In theEnabled is set to the
BTS2X version, Yes,parameter
the direct try
RACHflow is allowed
Busy if the
Threshold following whether
determines two conditions are met:
the timeslot is
busy and affects the normal access of the MS. The MS access is allowed only when the level of the MS random access burst is
The cell supports
greater the direct
than the RACH Busytry function.
Threshold.
The load of the cell is larger than or equal to the Cell Direct Try Forbidden Threshold.
In the BTS24 version, this parameter indicates the level threshold of the MS random access for the system to determine the RACH
busy state. When the receive level of the random Maxaccess
Times burst
a Celltimeslot
send Paging to MSthan the threshold, the BTS considers that the
is greater
timeslot is busy. This parameter also indicates whether the MS access is allowed. The MS access is allowed only when access level
(including random access and handover access) is greater than the threshold.
0-63 withthe
Informs 0 indicating
Network -110aboutdBm and Connection
UPLINK 63 indicatingStatus.Every
-47 dBm time BTS successfully decodesInMeasurement the BTS2X version Report(BTS24
sent not
by
included),
When BTSthis
MS,Counter parameter
sends physical
for indicates
information
determining the level
Radio to
Linkthethreshold
MS,isthe
Path for the
BTS system
starts
Incremented.But iftofails
the timer determine
T3105.If MS random
the
then decrements timer by access.When
T3105
1 untilltimes outthe
0 then BTSreceive
before ends levelthe
receive
Radio of a
random accessfrom
SAMB frame burstMS,
timeslot of the RACH
BTS re-sends physicalis greater
Connection than this
information
& sends to MSthreshold,
Connection the BTS
and restarts
Failure the considers
timer T3105.
Indication thatThe
to BSC the maximum
timeslot istimesbusy. forThisre-sending
parameter
During
mustasynchronous
physical be set basedison
information handover,
the actual
Ny1.The thesensitivity
MS constantly
physical of thesends
information BTS handover
and
is sent the lowest
through access
FACCH, bursts
access toisthe
level
which of BTS.
the
sent MS
everyUsually,
tofour
ensure the the
TDMA Timer T3124
uplink
frames andlasts
and 320
18 ms.
downlink
takes ms.
If the Upon
valuedetecting
balance. This
of T3105 the
parameter
is bursts,
also than
smaller the BTS
affects returns
or handover
equal to 18physical
access ofinformation
ms, then RACH BURST
BTS should to re-send
the MSasynchronous
during through
the physical the main DCCH/FACCH
handover.
information For
to the MS andwhen
BTS3X sends theand
series
the timer
MSG_ABIS_HO_DETECT
double-transceiver
T3105 times out forBTSs, the message
this parameter
first to thetimeout
time.This BSC. Meanwhile,
does notis affect MSthe
meaningless timer
access T3105
but
if the starts.The
affects
physical the report
information physical
of information
CCCH_LOAD_IND.
sent at the previous containing
Iftime information
theislevel
not received
sent on
on different
by
the the BCCH
FACCH physical
at thelayers
because network
the timeguarantees
isside correct
is greater
shorter MS
than athan access. If the timer
the period.Considering
FACCH RACH Busy T3105
Threshold, theexpires
the before
CCCH_LOAD_IND
previous the20
factors, BTSmsisreceives
counted the
once SAMB
is the reasonable frame
whether
minimum from
the
decoding is successful.value The RACH the
for this MS, the
whose levelBTS
parameter. isAtre-sends
lower thanthe
present, thephysical
the RACH Busy
default information
of thisto
valueThreshold the MS.
and
parameter whose is 70decoding
ms. is successful is also
counted. The measurement period is the RACH mean load timeslot. If the value of this parameter is too small, the BTS easily
If the numberthat
considers of resending
the RACHtimes timeslot exceeds
is busythisand
parameter (Ny1) andmessages
reports overload the BTS has receive
to the BSC. no correct
If the valueSAMB is tooframe,
high, the theBTS
BTScannot
sends the
determine This parameter
BSC a connection indicates whether
failure the better
In message, which 3Galsocellindicates
handover algorithm
handover istoallowed
failure.
During thethe state ofofthe
decision 3GRACH
bettertimeslot correctly.
cell handover the BTS24
algorithm, 3G betterversion,
cell ifhandover
this parameter is used
is originated only judge
whenbusy timeslot,
the period thatitsmeets
setting
isthe
consistent
conditionsthat
of in the
the 3GBTS30.
betterIfcellthishandover
parameter is the level
algorithm in thethreshold for validperiod
measurement random access, than
is greater its setting is consistent
3G Better Cell HO Validwith that
Time. in
the BTS20. The setting of this parameter for the BTS312, BTS3001C, BTS3001C+, BTS3002C and the double-transceiver BTSs is the
This parameter indicates the same
validastimethatofinthe
the3G BTS30.
better cell handover algorithm.
This parameter indicates the measurement time of the 3G better cell handover algorithm
If the Outgoing-RAT HO Allowed parameter is set to Yes and the Better 3G Cell HO Allowed parameter is set to Yes,better 3G cell
handover is triggered when the RSCP of a 3G neighboring cell is greater than RSCP Threshold for Better 3G CELL HO in a period.
This parameter indicates whether a 2G cell or a 3G cell is preferentially selected during cell handover
A quick switchover can be initiated only when the path loss difference between chain-type adjacent cells and serving cells is not
smaller than the value of this parameter within a measurement period.
This parameter indicates the level value to punish the original cell afthe a quick handover is triggerd
This parameter indicates the length of time to punish the orignal cell after a quick handover is performed
When the received number of measurement reports is no larger than the "Neglected Number of Measurement Reports", the
measurement reports are not filtered and the quick handover is not decided either.
This
The parameter
triggering prevents
of quick you frommust
switchover making an incorrect
conform switchover
to the P/N rule. Thatdecision on Pthe
is, within basis ofthere
seconds, an inaccurate
must be Nmeasurement report.
seconds in succession
when the triggering conditions are met: This parameter is applied in conjunction with the following parameters:Quick Handover Up
This parameter indicates the numberTrigger Level (dB) or Quick
of measurement Handover
reports filtered Down Trigger
after the Level (dB)
BSC receives measurement reports from serving
cells
Quick Handover Static Time
The quick switchover can be initiated only whenQuick the MS Move Speed
speed Thres (m/s)
is greater than Quick Move Speed Thres within a measurement
period.This parameter is applied in conjunction with the following parameters:
This parameter indicates the P mentioned previously. If the
Quick durationOffset
Handover when (dB)
the triggering conditions are met is not smaller than the
The quickvalue
switchover
of thiscan be initiated
parameter only
within when
the timethe downlink
preset level
by Quick of a serving
Handover cellTime,
Static is lower than
quick Quick Handover
switchover Down Trigger
is triggered.
Quick Handover Up Trigger Level (dB) or Quick Handover
Level within a measurement period after the measurement reports of the cell are Down Trigger Level
compensated.This (dB)
parameter is applied in
conjunction with the following parameters:
The quick switchover can be initiated only when the Quick Handover
uplink level ofStatic Timecell is lower than Quick Handover Up Trigger Level
a serving
within a measurement period after the measurement Quickreports of the Thres
Move Speed cell are filtered.This parameter is applied in conjunction with
(m/s)
Quick Handover
the following Last Time
parameters:
Quick Handover Static Time
Quick
Quick Handover
Handover Offset
Static (dB)
Time(0.5s)
Quick Handover Last Time
Quick Move Speed Thres (m/s)
Quick Handover Offset (dB)
If the ratio of channel occupancy in overlaid subcellQuickis greater than the
Handover Lastvalue
Timeof this parameter, it is not allowed to make the load
handover from underlaid cell to overlaid cell in an enhanced dual-band network.
Quick Handover Offset (dB)
P/N criterion: In P measurement reports, N measurement results meet handover requirements. Handover is started.
In P measurement reports, N measurement results meet handover requirements. Handover is started.This parameter indicates the
P in P/N criterion
After the handover succeeds, handover is not allowed within the time this parameter sets.
This parameter indicates the lowest threshold of overlaid subcell level of the handover from underlaid subcell to overlaid subcell.
This parameter indicates the lowest threshold of overlaid subcell level of the handover from underlaid subcell to overlaid subcell
This parameter indicates the period of the hierarchical handover from underlaid subcell to overlaid subcell. When the ratio of
This
overlaid subcell cellparameter indicates the
channel occupancy level step
is greater thanofthe
thevalue
load handover fromCell
of En Iuo Out overlaid subcell
General to underlaid
OverLoad subcell
Threshold, all the calls in the
cell request for handover at the same time. The BSC load is sharply increased, Thus the call may drop because the target cell is
congested.Therefore the algorithm of hierarchical handover is applied to hand over the calls in the cell hierarchically to the
underlaid subcell.
This parameter
This parameter indicates indicates
whether the
the load time duration
handover of everysubcell
from overlaid hierarchical handover.
to underlaid subcell is allowed.
If underlaid subcell load is higher than the value of Out Cell Serious OverLoad Threshold, the period of handover from underlaid
subcell cell to overlaid subcell cell is shortened by the value of Out Cell Serious OverLoad Threshold every second based on the
value of the Out Cell Load classification HO Period.
This parameter indicates the period of the hierarchical handover from underlaid subcell to overlaid subcell. When the ratio of
This parameter
overlaid subcell indicates
cell channel the level
occupancy step of
is greater thethe
than hierarchical handover
value of En Iuo Out from underlaid
Cell General subcell to
OverLoad overlaid all
Threshold, subcell
the calls in the
cell request for handover at the same time. The BSC load is sharply increased, Thus the call may drop because the target cell is
congested.Therefore the algorithm of hierarchical handover is applied to hand over the calls in the cell hierarchically to the
underlaid subcell.
When the ratio of underlaid subcell channel indicates
This parameter occupancy is high,
the whether of
time duration some calls
every in the overlaid
hierarchical subcell are allowed to be handed
handover.
over to the overlaid subcell.
To prevent ping-pong handover, the BSC determines whether the handover of the MS from overlaid subcell cell to underlaid subcell
cell based on the value of this parameter.Suppose the signal strength of serving cell is SS(s), and neighboring cell SS(n). If the value
of SS(s)-SS(n) is smaller than the value of Distance Between Out And Inn Cell boundary-Distance Hyst Between Out And Inn Cell
boundary, the MS handover from overlaid subcell cell to underlaid subcell cell is allowed
This parameter indicates the distance between the overlaid subcell and underlaid subcell. The value of this parameter is
comparative. The greater the value is, the longer the distance is.
If the current system flow level is greater than the value of this parameter, the handover between the overlaid subcell and
underlaid subcell because the underlaid subcell load is too high or too low, is not allowed.
If the ratio of the underlaid cell channel occupancy is greater than the value of this parameter, the period of handover from
underlaid subcell to overlaid subcell is reduced by the value of Out Cell Load HO Modify Step every second based on the value of
Out Cell Load Classification HO Period. Thus the handover from underlaid subcell to the overlaid subcell speeds up.
If the ratio of underlaid subcell channel occupancy is greater than the value of this parameter, some calls in the underlaid subcell
are handed over to the underlaid subcell. Moreover, calls initiated in the overlaid subcell are preferably assigned to the overlaid
subcell.
This parameter indicates whether the channel request in the overlaid subcell is preferably assigned between overlaid subcell and
underlaid subcell according to the Out Cell Low Load Threshold.
This parameter indicates whether the access request initiated in the underlaid subcell is preferably assigned between overlaid
subcell cell and underlaid subcell cell according to the Out Cell Low Load Threshold.
If the underlaid subcell channel occupancy ratio is smaller than the value of this parameter, some calls of the overlaid subcell is
handed over to the underlaid subcell. Moreover, the MS that requests for the overlaid subcell channel is preferably assigned to the
underlaid subcell.
This parameter indicates whether the better 3G cell handover algorithm is allowed
During the decision of 3G better cell handover algorithm, 3G better cell handover is originated only when the period that meets
the conditions of the 3G better cell handover algorithm in the measurement period is greater than 3G Better Cell HO Valid Time
This parameter indicates the measurement time of the 3G better cell handover algorithm
If the Outgoing-RAT HO Allowed parameter is set to Yes and the Better 3G Cell HO Allowed parameter is set to Yes, better 3G cell
handover is triggered when the Ec/No of a 3G neighboring cell is greater than Ec/No Threshold for Better 3G CELL HO in a period.0-
If the Outgoing-RAT HO Allowed parameter is set
49 with to Yes and-24
0 indicating thedB
Better 3G indicating
and 63 Cell HO Allowed
0 dB parameter is set to Yes,better 3G cell
handover is triggered when the RSCP of a 3G neighboring cell is greater than RSCP Threshold for Better 3G CELL HO in a period.
Received level threshold of the handover from the UL subcell to the OL subcell of the PS service in the PS concentric algorithm
Received level threshold of the handover from the OL subcell to the UL subcell of the PS service in the PS concentric algorithm
The values 0-70 of ReveiveQualThrshAMRHR correspond to RQ (received quality 0-7) x 10.
Cell congestion
Afterindicates
This parameter an OL tothe
UL penalty
handover fails,
time forno OL to UL ping-pong
forbidding handover request is allowed
handovers. before
After an OL tothe
UL penalty
handovertime expires. UL to OL
is performed,
handover is not allowed before the penalty time expires.
This parameter indicates the length of a grade in level grade-based UL to OL handover. Thus, high-level calls are handed over with
higher priority.This parameter and Underlay HO Step Period control the level band of the step-by-step handover from underlaid
This parameter indicates the interval between two grades
subcells of level-based
to overlaid handovers.When
subcells together. multiple UL to OL handover requests are
initiated simultaneously, it is possible that calls with low level are handed over. This does not conform to the principle that the call
with the best quality should be handed over firstly. Thus, level grade-based handover is used to hand over high-level calls with
higher priority.
This parameter indicates whether the traffic in the underlaid subcell determines the Enhanced Concentric underlaid to overlaid (UL
to OL) handover and the Enhanced Concentric overlaid to underlaid handover.
This is one of the parameters that determine the regions of overlaid and underlaid subcells,When Enhanced Concentric Cell is
allowed, the regions are co-determined by RX_QUAL Threshold, UtoO HO Receive Level Threshold, OtoU HO Receive Level
This is one of the parameters that determine the regions
Threshold, of overlaidand
TA Threshold, andTAunderlaid subcells. When Enhanced Concentric Cell is
Hysteresis
allowed, the regions are co-determined by RX_QUAL Threshold, UtoO HO Receive Level Threshold, OtoU HO Receive Level
Threshold, TA Threshold, and TA Hysteresis.
This parameter indicates the method of selecting an optimum layer for an incoming handover.
The default value is System Optimization. For a hybrid cell, the default value is Underlaid Subcell.The default value is System
Optimization. For a dual-timeslot extended cell or a hybrid cell, the default value is Underlaid Subcell
This parameter indicates the threshold of overlaid cell-based immediate assignment.If TA Pref of Imme-Assign Allowed is set to Yes,
the system prefers the channel in overlaid subcell while ACCESS_DELAY is smaller than TA Thrsh. of Imme- Assign pref. Otherwise,
This parameter indicates whether access_delay
the system isprefers
used in the
the channel
channel in request message
Underlaid subcell.for immediate assignment. When this
parameter is set to No, a channel in the underlaid subcell is assigned.
When this parameter is set to Yes, a channel in the overlaid subcell is assigned if access_delay is less than TA Threshold of Imme-
Assign
When the optimal layer is selected Pref. Ifsystem
through not, a channel in thethe
optimization, underlaid
currentsubcell
SDCCHislevel
assigned.
can be estimated (inserted/filtered)
based on the uplink measurement result in the previous SDCCH MR. Then, overlaid and underlaid subcells are allocated by
comparing this parameter and the receive level of SDCCH, and by comparing TA and the TA threshold of optimum assignment
This
Whenparameter indicates
the optimal layer the methodthrough
is selected of TCH assignment a concentric
system optimization, thecell.System Optimization:
current SDCCH The
level can be system selects
estimated the optimum
(inserted/filtered)
based on the uplink measurement serving layerinaccording
result to the
the previous MR provided
SDCCH MR. Then, through the
overlaid SDCCH.
and underlaid subcells are allocated by
comparing this parameter with the receive level of SDCCH, and by comparing TA with the TA threshold of optimum assignment.
Underlaid Subcell: Channel assignment in the underlaid subcell has higher priority.
Overlaid Subcell: Channel assignment in the overlaid subcell has higher priority.
This parameter indicates the duration when the conditions
No Preference: for a concentric
No specific cellis handover
instruction given. are met within UO HO Watch Time.
ThisThis parameter
is one indicates the
of the parameters thatduration
determineduring which the
the regions BSC counts
of overlaid andthe durationsubcells.When
underlaid when the conditions for an
Concentric concentric
Circles cell is
HO Allowed
set to No, the regions are handover are met
co-determined by to decideThreshold,
RX_LEV whether to triggerHysteresis,
RX_LEV a concentric cell handover.
RX_QUAL Threshold, TA Threshold, and TA
Hysteresis.
This is one of the parameters that determine the regions of overlaid and underlaid subcells.When Concentric Circles HO Allowed is
set toConcentric
When No, the regions
Circlesare
HOco-determined
Allowed is set by RX_LEV
to Yes, the Threshold,
regions areRX_LEV Hysteresis,
co-determined RX_QUALThreshold,
by RX_QUAL Threshold,UtoO
TA Threshold,
HO ReceiveandLevel
TA
Threshold, OtoU HO Receive LevelHysteresis.
Threshold, TA Threshold, and TA Hysteresis.
This is one of the parameters that determine the regions of overlaid and underlaid subcells.When Concentric Circles HO Allowed is
set toConcentric
When No, the regions
Circlesare
HOco-determined
Allowed is set by RX_LEV
to Yes, the Threshold,
regions areRX_LEV Hysteresis,
co-determined RX_QUALThreshold,
by RX_QUAL Threshold,UtoO
TA Threshold,
HO ReceiveandLevel
TA
Threshold, OtoU HO Receive LevelHysteresis.
Threshold, TA Threshold, and TA Hysteresis.
This is one of the parameters that determine the regions of overlaid and underlaid subcells. It is invalid when Enhanced Concentric
Cell Concentric
When is allowed.This is one
Circles HOof the parameters
Allowed thatthe
is set to Yes, determine theco-determined
regions are regions of overlaid and underlaid
by RX_QUAL subcells.
Threshold, UtoO It is
HOinvalid when
Receive Level
Enhanced
Threshold, OtoU HO Receive Concentric
Level CellTA
Threshold, is allowed.
Threshold, and TA Hysteresis.
When Enhanced Concentric Cell is not allowed, the regions are co-determined by RX_LEV Threshold, RX_LEV Hysteresis, RX_QUAL
Threshold, TA Threshold, and TA Hysteresis
This is one of the parameters that determine the regions of overlaid and underlaid subcells. It is invalid when Enhanced Concentric
Cell is allowed:When Enhanced Concentric Cell is not allowed, the regions are co-determined by RX_LEV Threshold, RX_LEV
Hysteresis,
This parameter indicates the signal RX_QUAL Threshold,
intensity compensation betweenTA the
Threshold,
overlaidand
andTA Hysteresis
underlaid subcells.It equals the sum of power
difference between overlaid and underlaid power amplifiers, insertion loss difference between combiners, path loss difference
caused by antennas, and path loss difference caused by frequencies.
This parameter indicates whether the TA is used to determine a Concentric Cell handover.
This parameter indicates whether the downlink receive level is used to determine a Concentric Cell handover
This parameter indicates whether the downlink receive quality is used to determine a Concentric Cell handover
This parameter indicates whether an underlay (UL) to overlay (OL) handover is allowed
The load threshold for the tight BCCH handover. To initiate the intra-cell tight BCCH handover, the load should be greater than the
threshold.
Signal quality threshold for the tight BCCH handover. To initiate the intra-cell tight BCCH handover, the downlink receiving quality
should be lower than the threshold
This parameter indicates the K offset used for K Ordering.To reduce the ping-pong effect during switchover, the BSC first deducts K
Bias from the actual downlink receiving level of a candidate cell. Then, the BSC performs K ordering over the downlink receiving
level of the candidate cell.
This parameter indicates the expected uplink receive level on a new channel after an MS is handed over to a new cell.
This parameter indicates the period during which penalty is performed on the neighboring cells of the fast moving MS.During this
period, penalty on the neighboring cells (on only the other three layers except the umbrella layer) of fast moving MS is valid.
This parameter indicates the penalty given to the level in a neighboring cell when an MS is moving fast.Only the cells in the
umbrella layer can give penalty to the cells in other three layers.
This parameter indicates the period for judging whether two continuous intra-cell handovers are consecutive
This parameter indicates the timer that starts when the threshold of maximum consecutive intra-cell handovers is reached.Intra-
This parameter indicates the maximumcell handovers
number is allowedintra-cell
of consecutive only when the timerallowed.If
handovers expires the interval of two continuous intra-
cell handovers is less than a specified threshold, the two handovers are regarded as consecutive handovers.
This parameter indicates
Intra-cellthe threshold
handover for judgingif whether
is forbidden an MS
the number moves fast across
of consecutive a cell.The
handovers threshold
exceeds is obtained based on the
this threshold.
cell radius and specified velocity.
If the time for crossing a cell is lower than this threshold, the MS is regarded as moving fast.
Suppose that the actual number of the micro cells that the MS fast crosses is N.According to the P/N rule,when the MS fast crosses
N ones among the P micro cells, a fast moving handover is triggered by the BSC when this parameter satisfies the required
conditions.
During
Duringthe
thehierarchical
moving, theload switchover,
MS passes thecells.According
P micro load switchovertoband starts
the P/N from
rule, Edgethe
when HOMSDLfast
RX_LEV Threshold
crosses N ones and a Load
among the HO Step
P micro
Level is added to the upper threshold of the
cells, the BSCload switchover
starts to triggerband every onemicro
a fast-moving Load cell
HO handover.
Step Period. In this way, the BSC conducts
switchover level by level. Finally, all the calls with the receiving level of the current serving cell ranging from Edge HO DL RX_LEV
Threshold to Edge HO DL RX_LEV Threshold + Load HO Bandwidth are switched over. The value of Load HO Step Level must be
If a cell load is not smaller than Load HO smaller than the
Threshold, allvalue of Load
the calls withHOthisBandwidth.
cell as the serving cell send switchover requests
simultaneously. As a result, the system load soars.In serious situations, the congestion may occur to this cell, thus leading to call
drop. To avoid call drop, the BSC uses the hierarchical load switchover algorithm to control the number of users who experience
The setting of this parameter is relevant with Edge HO DL RX_LEV
switchover at aThreshold.A
certain level.user is allowed to initiate load switchover only when
the receiving level of the user's current serving cell is within the range from Edge HO DL RX_LEV Threshold to Edge HO DL RX_LEV
Threshold + Load HO Bandwidth.
When the load handover is switched on, it is recommended that the Load HO Threshold is set to 85.
The cell load refers to TCH usage.
When the cell load exceeds the value of Load HO Threshold, the BSC starts the load handover. That is, the BSC starts the load
When the load handover is switched on, it isafter
handover recommended
the TCH in that the are
the cell Load HO Thresholdoccupied.
proportionally is set to 85.When the cell load exceeds the
value of Load HO Threshold, the BSC starts the load handover. That is, the BSC starts the load handover after the TCH in the cell are
System Flux Threshold for Load HO is obtained based on message load,
proportionally CPU load, and FID queuing load. The system flow level is
occupied.
the current flow control level of the system. 0-11: There are 12 flow control levels.Level 11 is the highest and level 0 is the lowest.
A load handover is allowed only when the system flow is lower than this threshold. Otherwise, unexpected situations may occur.
Therefore,
This parameter indicates the urgent switchover this
uplink parameter
quality must
control be set
for the AMRproperl)
HR service.The values of this parameter match
quality levels 0-7 multiplying 10. The urgent switchover is triggered only when the uplink receiving quality of the MS is greater than
the switchover threshold, that is, the receiving quality is poor.
This parameter indicates the urgent switchover downlink quality control for the AMR HR service.The values of this parameter
match quality levels 0-7 multiplying 10. The urgent switchover is triggered only when the downlink receiving quality of the MS is
greater than the switchover threshold, that is, the receiving quality is poor.
This parameter indicates the urgent switchover uplink quality control for the AMR FR service.The values of this parameter match
quality levels 0-7 multiplying 10.The urgent switchover is triggered only when the uplink receiving quality of the MS is greater than
the switchover threshold, that is, the receiving quality is poor.
This parameter indicates the urgent switchover downlink quality control for the AMR FR service. The values of this parameter
match quality levels 0-7 multiplying 10.The urgent switchover is triggered only when the downlink receiving quality of the MS is
When determining whethergreater
to initiate
thaninterference switchover,
the switchover thethat
threshold, system compares
is, the thequality
receiving difference between the receiving quality
is poor.
of the MS and this parameter with the switchover threshold.For the AMR calls, this parameter, together with RXQUALn, is used in
interference handover decision. An uplink interference handover is easily triggered if this parameter is set to a smaller value.
Quality threshold 12 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 11 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 10 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 9 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 8 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 7 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 6 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 5 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 4 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 3 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10
Quality threshold 2 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10.
Quality threshold 1 for the interference handover of non-AMR FR voice services. The value corresponds to (quality level 0-7) x 10
This parameter indicates the upper threshold of consecutive MRs containing no downlink measurement result for a call.Each call is
configured with a global timer, which counts the number of consecutive MRs containing no downlink measurement. When the
timer exceeds this threshold, the handover is disabled and the timer is reset.
This parameter indicates the uplink receive quality threshold of triggering an emergency handover when no measurement result
on downlink channels is contained in the MR.
This parameter is used to control the handover algorithm without downlink measurement report.If this parameter is set to 0, the
no handover algorithm without downlink measurement report is disabled. Therefore, handover decision without downlink
This parameter indicates the general trend measurement report is not
of a cell on receiving allowed
levels withininathis cell You can set this parameter for the filter
period.
when the levels of a cell plunge.If you attempt to initiate the switchover upon quick level decrease, the decrease trend of cell levels
These
must beparameters
increasinglyare used for the
remarkable configuration
as the of the Bfast
filter parameter drop filter.
becomes TheyThis
greater. are parameter
used in conjunction
should bewith the filter
applied parameterwith
in conjunction B,
which are 9 parameters in total as filter parameters. In the
the filter program,A1
parameters 10through
is deducted
A8. from the actual values of A1-A8.C1(nt) = A1 x
C(nt) + A2 x C(nt-t) + A3 x C(nt-2t) + ... + A8 x C(nt-7t), where:
The parameters A1-A8 of the filter must meet the requirement: A1 + A2 + A3 + A4 + A5 + A6 + A7 + A8 = 80
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
These parameters are used for the configuration of the fast drop filter. They are used in conjunction with the filter parameter B,
which are 9 parameters in total as filter parameters.
This parameter indicates the uplink receive quality threshold of triggering an emergency handover.When the receive quality of the
This parameter
uplink is greaterindicates the downlink
than UL Qual Threshold,receive quality threshold
an emergency handover ofistriggering
triggeredan emergency
due handover.When
to bad quality.When the receive
frequency quality
hopping of
or DTX
the downlink is greater thanof DLthe
Qual
cellThreshold, an emergency
is enabled,it handover
is recommended thatisyou
triggered.When frequency
set this parameter to 70 hopping or DTX of the cell is
enabled,
When an it isemergency
recommended that you
handover set this parameter
is triggered, to 70. When
inter-cell handover takes anpriority.
emergency handoverhandover,
An intra-cell is triggered, inter-cell
however, handoverif takes
is triggered no
priority. An intra-cell handover, however,cell
candidate is triggered if no
is available andcandidate
intra-cellcell is available
handovers and intra-cell handovers are allowed.
are allowed
This is one of the parameters that determine the regions of overlaid and underlaid subcells.When Concentric Circles HO Allowed is
set to No, the regions are co-determined by RX_LEV Threshold, RX_LEV Hysteresis, RX_QUAL Threshold, TA Threshold, and TA
Hysteresis.
When Concentric Circles HO Allowed is set to Yes, the regions are co-determined by RX_QUAL Threshold, UtoO HO Receive Level
By setting this parameter,Threshold, OtoUvalues
you can select HO Receive
from a Level Threshold,
measurement TA Threshold,
report. and TA
If the sender Hysteresis.
uses DTX when this parameter is set to
Open, select SUB from measurement reports. Otherwise, select FULL from measurement reports
This parameter indicates the length of the penalty timer for handover failure between adjacent cells due to incorrect data
configuration.
This parameter indicates the length of the penalty timer for handover failure between adjacent cells due to failed air interface
connection.
This parameter indicates the length of the penalty timer for handover failure between adjacent cells due to cell congestion
This parameter indicates the length of the filter on the NBR_RCVD_BLOCK traffic channel when the measurement report type is
EMR.By setting this
This parameter parameter,
indicates you can
the length usefilter
of the NBR_RCVD_BLOCK of multiple signaling
on the NBR_RCVD_BLOCK EMRs, thus avoiding
channel inaccuracy
when owing to the
the measurement use of
report only
type is
EMR.By setting this parameter, you can use NBR_RCVD_BLOCK oneofEMR
multiple EMRs, thus avoiding inaccuracy owing to the use of only
This parameter determines the penalty time for AMR full rate one
to EMR.
half rate (FR-to-HR) handovers. Before the timer expires, no AMR
FR-to-HR handover request is allowed if the previous full-half handover fails due to channel unavailability or channel mismatch.
As the MS stays on the signaling channel shorter than on the traffic channel, this parameter should be set to a smaller value.
The greater the value of this parameter is, the longer the penalty time after AMR TCHF-H HO fails is. That is, triggering AMR
handover becomes more difficult.
This parameter indicates the length of the filter on the REP_QUANT voice channel when the measurement report type is EMR.By
This parameter
setting indicates
this parameter, youthe
canlength of the filter of
use REP_QUANT onmultiple
the REP_QUANT
EMRs, thussignaling channel
avoiding whenowing
inaccuracy the measurement
to the use of report type
only one is
EMR
EMR.By setting this parameter, you can use REP_QUANT of multiple EMRs, thus avoiding inaccuracy owing to the use of only one
EMR.
As the MS stays on the signaling channel shorter than on the traffic channel, this parameter should be set to a smaller value.
This parameter indicates the number of previous measurement reports obtained when you average CV_BEP of the traffic channel
This parameter indicates the number of previous
during measurement
the process forreports obtained
averaging EMRs when you average CV_BEP of the signaling
channel during the process for averaging EMRs.By setting this parameter, you can use CV_BEP of multiple EMRs, thus avoiding
inaccuracy owing to the use of only one EMR.
This parameter
As the MS staysindicates the number
on the signaling of previous
channel measurement
shorter than reports
on the traffic obtained
channel, this when you average
parameter MEAN_BEP
should be of the traffic
set to a smaller value
channel during the process for averaging.By setting this parameter, you can use MEAN_BEP of multiple EMRs, thus avoiding
This parameter indicates the number of previous measurement reports obtained when
inaccuracy owing to the use of only one EMR. you average MEAN_BEP of the signaling
channel during the process for averaging EMRs.By setting
enhanced this parameter,
measurement you (EMRs).
reports can use MEAN_BEP of multiple EMRs, thus avoiding
inaccuracy owing to the use of only one EMR.
As the MS camps on the signaling channel shorter than on the traffic channel, this parameter should be set to a smaller value.
This parameter indicates the penalty time given to the original serving cell where emergency handover is performed due to TA.
This parameter indicates the penalty level given to the original serving cell where emergency handover is performed due to
TA.After emergency handover is performed due to TA, the receive level of the original serving cell is decreased by the penalty level.
Thus, other cells are given higher priority and handover to the original serving cell is not allowed.
This parameter indicates the penalty time given to the original serving cell where emergency handover is performed due to bad
quality.
This parameter indicates the penalty level given to a target cell.A penalty level is given to a target cell to avoid further attempts
when a handover fails due to any of the following reasons:
After emergency handover is performed due to bad quality, the receive level of the original serving cell is decreased by the penalty
level. Thus, other cells are given higher priority
Celland handover to the original serving cell is not allowed.
congestion
A message
This parameter indicates indicating
the number ofUm interface
previous handover failure
measurement reportsisobtained
received when
duringyou
out-going
averageBSC
thehandover.
timing advances during the
process for averaging the measurement reports.
A message indicating Um interface handover failure is received during internal handover
This parameter indicates the number of previous measurement reports obtained when you average the signal strength of adjacent
cells during the process for averaging measurement reports
This is Filter Length(How many MR are to be taken) Network will require for decision of SDCCH Qual HO.TVH HO will initiate
depending upon specific no of MR.
This is Filter Length(How many MR are to be taken) Network will require for decision of SDCCH HO.TVH HO will initiate depending
upon specific no of MR.
This is Filter Length(How many MR are to be taken) Network will require for decision of TCH Qual HO.TVH HO will initiate
depending upon specific no of MR.
This is Filter Length(How many MR are to be taken) Network will require for decision of TCH HO.TVH HO will initiate depending
upon specific no of MR.
This parameter indicates the number of measurement reports allowed to be continuously lost in the interpolation calculation.
If the number of continuously lost measurement reports is not larger than the value, the value of the lost measurement reports is
obtained through the linear interpolation method based on the beginning and ending values of the continuously lost measurement
reports.
This parameter
Otherwise, the lost measurement reports areisdiscarded
used to select the measurement
and the candidate cellsreports
during are
directed retry again when the new reports
calculated
arrive.
After the MR is preprocessed by BTS, the BTS transfers the preprocessed MR to the BSC.This parameter indicates the frequency that
the BTS transfers the preprocessed MR to the BSC
This parameter indicates whether the original BS/MS power class is transferred to the BSC
Determines whether MS will process measurement Report & then send it or just send MR to BTS. If it is Pre-process then MS must
also send Originl MR with that MR
Determines whether MS will process measurement Report & then send it or just send MR to BTS. If it is Pre-process then MS must
also send Originl MR with that MR
This parameter indicates whether the MS uses the optimum transmit power to access a new channel after the handover.
This parameter indicates whether penalty is given to certain cells, including target cells where handover fails and serving cells
where handover is triggered due to excessive TA or poor signal strength.
This parameter indicates whether an inter-BSC SDCCH handover is allowed. An inter-BSC SDCCH handover is triggered when an MS
succeeds in requesting SDCCH but fails to request TCH in a BSC.
This parameter indicates the minimum interval between two consecutive emergency handovers.
This parameter is used to prevent Ping-Pong HO due to any reason. Any kind of HO is not activated after the time of first HO
This parameter indicates the duration of a timer, which starts upon new SDCCH assignment and triggers handover upon timeout. To
avoid incorrect handovers caused by the inaccurate measurements at early stage of call establishment.
To indicate the duration of a timer, which starts upon new TCH assignment and triggers handover upon timeout. To avoid incorrect
handovers caused by the inaccurate measurements at early stage of call establishment.
This parameter indicates whether to switch on/off the concentric DTCB handover.
This parameter indicates P of the P/N criterion for the tight BCCH handover
This parameter indicates N of the P/N criterion for the tight BCCH handover.
This parameter indicates whether an quick handover is allowed.
This parameter indicates the threshold of TCHH to TCHF handover.
This parameter indicates the threshold of a handover from full rate data TCH (TCHF) to half rate data TCH (TCHH).
This parameter indicates the period that satisfies full rate to half rate handover.
This parameter indicates the time threshold that satisfies full rate to half rate handover.
To indicate whether the handover between the full rate and half rate is allowed or not.
This parameter indicates the lower threshold of downlink receive level when a cell becomes a candidate cell.
This parameter indicates the lower threshold of Uplink receive level when a cell becomes a candidate cell.
This parameter indicates the hysteresis of an inter-layer or inter-priority handover. It is used to avoid inter-layer ping-pong
This parameter indicates the Threshold of an inter-layerhandovers.
or inter-priority handover. It is used to avoid inter-layer ping-pong
handovers.
To indicate the UL receive level threshold of an edge handover. An edge handover will be triggered if the uplink receive level is
constantly lower than "Edge HO UL RX_LEV Thrsh." for a period longer than Edge HO Valid Time(s) within Edge HO Watch Time(s).
To indicate whether an interference handover is allowed. An interference handover is triggered when the receive level is higher
than the receive threshold, but the transmission quality is lower than the handover triggering threshold
This parameter indicates whether a concentric circle handover is allowed ( 900 to 1800 & 1800 to 900 )
The parameter indicates whether a Timing Advance (TA) handover is allowed. A TA handover is triggered when the TA is higher
than the triggering threshold
To indicate whether a Bad quality handover is allowed. BQ handover is triggered when Bit Error Ratio (BER) over uplink/downlink
channels is higher than the triggering threshold.
To indicate whether a fringe handover is allowed. A fringe handover is used to prevent call drops in cell edges and initiated when
the downlink level in the serving cell is lower than Edge HO DL RX_LEV Threshold or the uplink level in the serving cell is lower than
Edge HO UL RX_LEV Threshold.
The parameter indicates whether the layer level handover is allowed. To guide the traffic to the cell that has high priority.
To indicate whether a power budget handover is allowed. Calculations for the power budget handovers are based on path loss and
search for desired cell in real time and the cell must provide less path loss and other requirements.
The parameter indicates whether the emergency handover algorithm is allowed. The emergency handover algorithm is used to
prevent call drops when the receive level of the MS drops rapidly
This parameter indicates whether a fast moving handover is allowed. The fast moving handover enables a fast moving MS to hand
over rapidly to a macro cell, thus reducing handovers.
This parameter indicates whether a traffic load-sharing handover is allowed. Load-sharing functions only within the same BSC or in
cells of the same layer. It applies to only TCH.
This parameter indicates whether the sequence of candidate cells is adjusted. After the sequence is adjusted, the handover within
the same BSC/MSC takes priority
To indicate the receive quality gain when the number of frequency hopping is 8. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 7. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 6. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 5. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 4. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 3. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 2. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
To indicate the receive quality gain when the number of frequency hopping is 1. The receive quality is brought out when the cell is
configured with the frequency hopping. BSC performs power control based on the gain.
This parameter indicates the maximum permissible adjustment step when the BSC increases uplink transmit power according to
signal quality.
This parameter indicates the maximum permissible adjustment step when the BSC reduces uplink transmit power according to
signal quality.
This parameter indicates the lower threshold of downlink power control quality level of AMR half-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of uplink power control quality level of AMR half-rate traffic channel. When the
receive quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of AMR full-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of uplink power control quality level of AMR full-rate traffic channel. When the
receive quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of half-rate traffic channel. When the receive
quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of uplink power control quality level of half-rate traffic channel. When the receive
quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of full-rate traffic channel. When the receive
quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of uplink power control quality level of full-rate traffic channel. When the receive
quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of uplink power control signal level. When the receive level is smaller than the value
of this parameter, the BSC performs the HW III power control.
This parameter indicates the upper threshold of uplink power control signal level. When the receive level is higher than the value
of this parameter, the BSC performs the HW III power control.
This parameter indicates the step ratio of the quality level adjusted by uplink power control.
This parameter indicates the step ratio of the signal strength adjusted by uplink power control
This parameter indicates the period of the filtering of quality level smooth window through uplink power control.
This parameter indicates the period of the filtering of signal level smooth window through uplink power control.
This parameter indicates the period of the filtering quality level index through uplink power control.
This parameter indicates the period of the filtering of signal level index through uplink power control.
This parameter indicates the maximum permissible adjustment step during up power control adjustment based on signal quality.
This parameter indicates the maximum permissible adjustment step during down power adjustment based on signal quality.
This parameter indicates the lower threshold of downlink power control quality level of AMR half-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of downlink power control quality level of AMR half-rate traffic channel. When the
receive quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of AMR half-rate traffic channel. When the
receive quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of downlink power control quality level of AMR full-rate traffic channel. When the
receive quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of half-rate traffic channel. When the receive
quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of downlink power control quality level of half-rate traffic channel. When the receive
quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control quality level of full-rate traffic channel. When the receive
quality is lower than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the upper threshold of downlink power control quality level of full-rate traffic channel. When the receive
quality is higher than the value of this parameter, the BSC performs HW III power control.
This parameter indicates the lower threshold of downlink power control signal level. When the receive level is lower than the value
of this parameter, the BSC performs the downlink power control.
This parameter indicates the upper threshold of downlink power control signal level. When the receive level is higher than the
value of this parameter, the BSC performs the downlink power control.
This parameter indicates the step ratio of the quality level adjusted by downlink power control.
This parameter indicates the step ratio of the signal strength adjusted by downlink power control.
This parameter indicates the smooth window filter length of quality level through downlink power control.
This parameter indicates the smooth window filter length of signal level through downlink power control.
This parameter indicates the exponent filter length of quality level through downlink power control.
This parameter indicates the exponent filter length of signal level through downlink power control.
This parameter indicates the maximum number of allowed discarded TCH measurement reports in a power control period.
This parameter indicates the maximum number of allowed discarded SDCCH measurement reports in a power control period.
This parameter indicates the shortest interval between two continuous downlink power control commands
This parameter indicates the shortest interval between two continuous uplink power control commands.
When the number of discarded measurement reports within the power control period is greater than the value of this parameter,
the BSC stops power control.
This parameter indicates the maximum range of dynamic power adjustment for the BTS. If the value of this parameter is too small,
the dynamic power adjustment capability of the BTS is lowered.
During downlink power control, when the quality of received downlink signals is larger than or equal to DL Qual Bad TrigThreshold,
the actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff.
During downlink power control, when the quality of received downlink signals is larger than or equal to this trigger threshold, the
actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff in the data configuration
During downlink power control, when the quality of received downlink signals is larger than or equal to DL Qual Bad TrigThreshold,
the actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff.
During uplink power control, when the quality of received uplink signals is larger than or equal to this trigger threshold, the actual
value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff in the data configuration
This parameter determines the maximum permissible adjustment step during power adjustment based on the quality.
This parameter determines the maximum permissible adjustment step during up power adjustment based on the level.
This parameter determines the maximum power adjustment step permitted by power control when the RQ value is 0.
When the power control step is calculated according to the signal quality, the quality of the received signal has an upper threshold
and a lower threshold. When the signal quality exceeds the upper threshold or is below the lower threshold, power control is
performed. This parameter determines the downlink quality lower threshold for power control
This parameter determines the downlink quality upper threshold for power control.
This parameter determines the lower threshold of the downlink signal for the AMR power control. If the signal level is below this
threshold, calculate an increased value (= (AMR DL RX_LEV Upper Threshold +AMR DL RX_LEV Lower Threshold)/2 - Received
Level).
This parameter determines the upper threshold of the downlink signal for the AMR power control. If the signal level exceeds this
threshold, calculate a decreased value (= Received Level- (AMR DL RX_LEV Upper Threshold +AMR DL RX_LEV Lower Threshold)/2).
This parameter determines the uplink quality lower threshold for the AMR power control.
This parameter determines the uplink quality upper threshold of the stable state quality zone.
This parameter determines the lower threshold of the uplink signal for power control. If the signal level is below this threshold,
calculate an increased value (= (AMR UL RX_LEV Upper Threshold +AMR UL RX_LEV Lower Threshold)/2 - Received Level).
This parameter determines the upper threshold of the uplink signal for power control. If the signal level exceeds this threshold,
calculate a level adjustment value (=Received Level-(AMR UL RX_LEV Upper Threshold +AMR UL RX_LEV Lower Threshold)/2 ).
In Huawei II power control algorithm, the prediction function is added in the filter to compensate the dela of power adjustment.
This parameter determines the number of downlink measurement reports for prediction.
This parameter determines the number of uplink measurement reports for prediction
When this parameter is set to Yes, the Huawei II power control algorithm puts the received measurement reports in the
measurement report compensation queue and then records the change in transmit power based on the MS power and the BTS
When the network receives measurement reports, power in the measurement
an average report
value of downlink signal quality values in consecutive measurement
reports should be obtained to reflect the radio environment where the BTS locates. This parameter indicates the number of
measurement reports in which the average of the downlink signal quality is taken before BTS power adjustment.
When the network receives measurement reports, an average value of uplink signal quality values in consecutive measurement
reports should be obtained to reflect the radio environment where the MS locates. This parameter indicates the number of
measurement reports in which the average of the uplink signal quality is taken before MS power adjustment.
This parameter indicates the number of measurement reports in which the average of the downlink signal strength is taken before
BTS power adjustment
This parameter indicates the number of measurement reports in which the average of the uplink signal strength is taken before
AMR MS power adjustment.
Minimum time interval between two continuous AMR power control commands
To indicate the maximum range of dynamic power adjustment for the BTS. Smaller the value, dynamic adjustment capability of BTS
is lowered.
During downlink power control, when the quality of received downlink signals is larger than or equal to DL Qual Bad TrigThreshold,
the actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff.
During downlink power control, when the quality of received downlink signals is larger than or equal to this trigger threshold, the
actual value of DL RX_LEV Upper Threshold is the one plus the value of DL Qual Bad Up LEVDiff.
During uplink power control, when the quality of received uplink signals is larger than or equal to UL Qual Bad TrigThreshold, the
actual value of UL RX_LEV Upper Threshold is the one plus the value of UL Qual Bad Up LEVDiff.
During uplink power control, when the quality of received uplink signals is larger than or equal to this trigger threshold, the actual
value of UL RX_LEV Upper Threshold is the one plus the value of UL Qual Bad Up LEVDiff in the data configuration.
This parameter determines the maximum permissible adjustment step during down power adjustment based on the quality of
received signals.
This parameter determines the maximum permissible adjustment step during up power adjustment based on the level.
This parameter determines the maximum permissible adjustment step during power adjustment based on the quality.
In the Huawei II power control algorithm, three quality zones (0, 1-2, 3) are defined according to the quality of received signals.
This parameter indicates the maximum power control step permitted when the received signals are within quality zone 2 (RQ value
3) and when the power is lowered based on the level.
This parameter indicates the maximum power control step permitted when the received signals are within quality zone 1 (0 < RQ
value < 3) and when the power is lowered based on the level.
This parameter
After indicates
the BSC delivers the the maximum
power control power control
command, step
it will bepermitted when the
a period before the received signals
BSC receives an are within quality zone
acknowledgement 2 (1< RQ
message. The
measurement reports lag behind value <3) and when
the changes in thethe
MS power is lowered
received level andbased
in theon
MSthe level. signal quality. Thus the power
received
adjustment is delayed. in a short period of time, the BSC samples several downlink measurement reports and performs weighted
filtering, predicting N measurement reports after the current time. This parameter indicates the number of downlink measurement
reports predicted by the BSC. The value of the parameter equals the previous number N.
This parameter indicates the number of uplink measurement reports predicted by the BSC. The value of the parameter equals the
previous number N.
If this parameter is set to Yes, the BSC or BTS puts the received measurement reports in the measurement report compensation
queue. Then record the change of transmit power based on the MS power and the BTS power in the measurement report. After
values are added in the measurement report, compensate the received level value in the historical measurement report based on
To reflect the current radio environment where MS locates, BSS receive
the change measurement reports and an average value of uplink signal
of power.
quality is obtained in consecutive MR. This parameter indicates the number of measurement reports in which the average of the
downlink signal quality is taken before BTS power adjustment.
This parameter indicates the number of measurement reports in which the average of the uplink signal quality is taken before MS
power adjustment
This parameter indicates the number of measurement reports in which the average of the downlink signal strength is taken before
BTS power adjustment.
This parameter indicates the number of measurement reports in which the average of the uplink signal strength is taken before MS
power adjustment.
To indicate whether BSC applies HW III power control algorithm. Yes: BSC Applies; NO: BSC does not apply
In order to calculate the power control according to the signal quality, the quality of the received signal has upper threshold and
lower threshold. This parameter determines the downlink quality lower threshold for the power control.
This parameter determines the downlink quality upper threshold for the power control.
This parameter determines the lower threshold of the downlink signal for power control. If the signal level is below this threshold,
calculate an increased value (= (DL RX_LEV Upper Threshold+DL RX_LEV Lower Threshold)/2 - Received Level).
This parameter determines the upper threshold of the downlink signal for power control. If the signal level exceeds this threshold,
calculate a decreased value (= Received Level - (DL RX_LEV Upper Threshold+DL RX_LEV Lower Threshold)/2).
This parameter determines the uplink quality lower threshold for the power control.
This parameter determines the uplink quality upper threshold of the stable state quality zone. The upper threshold is larger than or
equal to the lower threshold.
The step of power control is determined by UL RX_LEV Upper Threshold and UL RX_LEV Lower Thrsh. If the uplink signal strength is
within the range from UL RX_LEV Upper Threshold to UL RX_LEV Lower Thrsh, power control on the MS is not performed. If the
uplink signal strength is beyond the range, power control on the MS is performed.
If the uplink signal strength is within the range from UL RX_LEV Upper Threshold to UL RX_LEV Lower Thrsh, power control on the
MS is not performed. If the uplink signal strength is beyond the range, power control on the MS is performed.
Minimum time interval between two continuous power control commands
If the uplink received level difference of calls of the same timeslot exceeds threshold of the difference between uplink received
levels, the situation must be recorded.During the observation of N seconds, if this situation lasts P seconds, the call with the
highest uplink signal intensity in the timeslot should be handed over to another timeslot.
If the uplink received level difference of calls of the same timeslot exceeds threshold of the difference between uplink received
levels, the situation must be recorded.During the observation of N seconds, if this situation lasts P seconds, the call with the
highest uplink signal intensity in the timeslot should be handed over to another timeslot.
The value is 0-1 in fact; however, RRM and CM are multiplied by 10 to prevent floating-point values.
This parameter indicates whether the BSC is allowed to assign the half-rate channels and full-rate channels to the MS according to
the channel seizure ratio of the underlaid subcell and overlaid subcell.
The BSC assigns channels in underlaid subcell to the MS in the concentric cell. If the channel seizure ratio of underlaid subcell is
higher than the value of this parameter, half-rate channels are assigned; if the channel seizure ratio of underlaid subcell is not
higher than the value of this parameter, full-rate channels are assigned.
The BSC assigns channels in overlaid subcell to the MS in the concentric cell. If the channel seizure ratio of overlaid subcell is
greater than the value of this parameter, half-rate channels are assigned. If the channel seizure ratio of overlaid subcell is not
greater than the value of this parameter, full-rate channels are assigned.
This parameter indicates whether dynamic HSN is permissible to use. To reduce the inter frequency interference
This parameter indicates whether the BSC enables the function of FlexMAIO. When the frequency hopping and FlexMAIO are
enabled in a cell, part of the intra-frequency interferences can be avoided.
To control the Abis resource load threshold. When Abis resource load is lower than this threshold, full rate channel is assigned.
When the static Abis resource load is greater than the static Abis load threshold, half-rate channel is preferably assigned if the
dynamic Abis resource load is greater than the value of this parameter; full-rate channel is preferably assigned when if the dynamic
Abis resource load is not greater than the value of this parameter.
If the dynamic PDCHs configured in the cell are occupied by the PCU, the BSC periodically reclaims dynamic PDCHs from the PCU
when the CS services of the cell are overloaded.
The channel type to be assigned is decided according to the channel types that are allowed by the MSC and the percentage of
seized TCHs in the cell.
This parameter indicates whether the TCH/H prior function is allowed during the channel assignment.
Lower threshold for updating the history priorities of channels
This parameter indicates the duration after which the flow of updating the history channel priority starts.
This parameter indicates how many measurement reports are used to determine the quality of SDCCHs.
This parameter indicates how many measurement reports are used to determine the level of SDCCHs.
This parameter indicates how many measurement reports are used to determine the quality of TCHs.
This parameter indicates how many sequential measurement reports are used to determine the level of TCHs.
This parameter indicates the interference threshold of the downlink channel quality.
This parameter indicates the interference threshold of the downlink channel level.
This parameter indicates the interference threshold of the uplink channel quality. The higher the level, the greater the signal
strength is. The greater the quality, the lower the signal strength is.
This parameter indicates the interference threshold of the uplink channel level. The higher the level, the greater the signal strength
is. The greater the quality, the lower the signal strength is.
This parameter indicates whether the random selection of the channels as the start of the channel traversal is allowed.
This parameter indicates whether the factor of the history record priority is effective in the channel priority.
This parameter indicates whether the TRX priority factor is effective in the channel priority.
This parameter indicates whether the interference measurement of the occupied channels is allowed.
This parameter indicates whether the interference priority factor is effective in the channel priority. Yes: Effective; No: ineffective
This parameter indicates whether to turn on the switch for the tight BCCH algorithm, and thus controls whether to enable the
BCCH aggressive frequency reuse algorithm.
This parameter indicates whether the current cell supports the dynamic transmission diversity or dynamic PBT
This parameter sets the priority of different types in channel allocation. These types include:priority by capacity, priority by quality,
relative priority by PS domain, absolute priority by PS domain
This parameter indicates whether the channel rearrangement (two single TCHHs are rearranged as a TCHF) is allowed.
This parameter indicates the minimum time for the recovery of a TCH from an SDCCH.
This parameter indicates the maximum number of SDCCHs that can be configured in a cell.
When the number of idle SDCCHs in a cell is smaller than or equal to the value of this parameter, more TCHs in the cell are changed
into SDCCHs.
The BSC delivers the ChannelRelease message and the AMRHR encoding mode, and enables the T3109 (AMRHR) timer. If the BSC
receives the ReleaseIndication message before the T3109 (AMRHR) timer expires, the T3109 (AMRHR) timer stops; if the T3109
(AMRHR) timer expires, the BSC deactivates the channel.
The BSC delivers the ChannelRelease message and the AMRFR encoding mode, and enables the T3109 (AMRFR) timer. If the BSC
receives the ReleaseIndication message before the T3109 (AMRFR) timer expires, the T3109 (AMRFR) timer stops; if the T3109
(AMRFR) timer expires, the BSC deactivates the channel.
The T3103 timer starts when the intra-BSC handover command is sent and ends when the handover is complete. If the timer
expires, the intra-BSC handover fails.
This parameter indicates the timer that the WaitIndcation information element carries when the BSC sends the Immediate
Assignment Reject message to the MS. The MS receiving the Immediate Assignment Reject message attempts to access the
network after the period specified by this parameter.
The T8 starts when the handover command is sent and ends when the successful handover message is received. If the timer
expires, the out-BSC handover is regarded as unsuccessful
The T3121 timer starts when the handover request is sent and ends when the handover complete message is received. If the timer
expires, the ClearReq message is sent.
The T3107 timer starts when the assignment command is sent and ends when the assignment complete message is sent. If the
timer expires, the assignment fails and the seized channels are released.
The T7 timer starts when the handover request message is sent and ends when the handover response message is reported. If the
timer expires, the outgoing BSC handover fails.
The T3103 timer starts when the intra-BSC handover command is sent and ends when the handover is complete. If the timer
expires, the intra-BSC handover fails.
This timer starts when the CR message is reported and ends when the CC message is received. If the timer expires, the seized
SDCCH is released.
If the timer expires, the seized SDCCH is released. If the reception of the EST IND message expires, the BSS releases the seized
SDCCH.
This parameter indicates the maximum number of paging messages that a cell is allowed to send within a statistical period.
This parameter indicates the average number of paging messages that a cell is allowed to send within a statistical period.
This parameter indicates the maximum number of messages in the buffer of the cell paging group packet when the Cell Paging
Message Group Packet Function Switch is turned on.
This parameter indicates the interval between two cell paging group packets, which is an integral multiple of 50 ms.
The cell paging message packaging is determined by the system load. If the paging message packaging timer is enabled, the paging
messages are packaged according to cells; otherwise, the paging messages are packaged according to the MTLS.
This parameter indicates the algorithm type of the interference band measurement when frequency scan is enabled: interference
band algorithm I or interference band algorithm II.
This parameter indicates the algorithm type of the interference band measurement when frequency scan is enabled: interference
band algorithm I or interference band algorithm II.
This parameter indicates when BTSs are cascaded, whether the BSC allows the CS service to preempt the sublink resources of the
PS service of the lower-level BTS if the sublink of the BTS cannot be preempted.
This parameter indicates whether the BSC allows the CS service to preempt the sublink resources of the PS service.
This parameter indicates whether the BSC forces the MS to send the handover access message.
This parameter indicates whether the MS can be handed over to other channels through assignment procedure in intra-cell
handover.
Every UL frequency is scanned for 10 times. The average of the 10 levels is reported. The result type is main/diversity before, and
maximum/average is new added.
If this parameter is set to 0, the call drop caused by the expiration of the intra-cell handover is not measured as a call drop. If this
parameter is set to 1, the call drop caused by the expiration of the intra-cell handover is measured as a call drop.
If this parameter is set to 0, the call drop caused by the expiration of the intra-BSC out-cell handover is not measured as a call drop.
If this parameter is set to 1, the call drop caused by the expiration of the intra-BSC out-cell handover is measured as a call drop.
If this parameter is set to 0, the call drop caused by the expiration of the out-BSC handover is not measured as a call drop. If this
parameter is set to 1, the call drop caused by the expiration of the out-BSC handover is measured as a call drop.
If this parameter is set to 0, the call drop caused by the expiration of the into-BSC handover is not measured as a call drop. If this
parameter is set to 1, the call drop caused by the expiration of the into-BSC handover is measured as a call drop.
If this parameter is set to 0, the call drop caused by the resource check is not measured as a call drop. If this parameter is set to 1,
the call drop caused by the resource check is measured as a call drop.
this parameter is set to 0, the call drop caused by the unavailability of measurement reports on the MS for a long time is not
measured as a call drop. If this parameter is set to 1, the call drop caused by the unavailability of measurement reports on the MS
for a long time is measured as a call drop.
If this parameter is set to 0, the call drop caused by the forced handover failure is not measured as a call drop. If this parameter is
set to 1, the call drop caused by the forced handover failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the Abis territorial link failure is not measured as a call drop. If this parameter is
set to 1, the call drop caused by the Abis territorial link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the Abis territorial link failure is not measured as a call drop. If this parameter is
set to 1, the call drop caused by the Abis territorial link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by either of the following factors is not measured as a call drop,If this parameter is
set to 0, the call drop caused by either of the following factors is not measured as a call drop:
If this parameter is set to 0, the call drop caused by other reasons of connection failure (besides the previous four connection
failures) is not measured as a call drop. If this parameter is set to 1, the call drop caused by other reasons of connection failure
(besides the previous four connection failures) is measured as a call drop.
If this parameter is set to 0, the call drop caused by the unavailability of radio resources is not measured as a call drop. If this
parameter is set to 1, the call drop caused by the unavailability of radio resources is measured as a call drop.
If this parameter is set to 0, the call drop caused by the OM intervention is not measured as a call drop. If this parameter is set to 1,
the call drop caused by the OM intervention is measured as a call drop.
If this parameter is set to 0, the call drop caused by the HO access failure is not measured as a call drop. If this parameter is set to 1,
the call drop caused by the HO access failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the radio link failure is not measured as a call drop. If this parameter is set to 1,
the call drop caused by the radio link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the radio link failure is not measured as a call drop. If this parameter is set to 1,
the call drop caused by the radio link failure is measured as a call drop.
If this parameter is set to 0, the call drop caused by the error of unsolicited DM response is not measured as a call drop. If this
parameter is set to 1, the call drop caused by the error of unsolicited DM response is measured as a call drop.
If this parameter is set to 0, the call drop caused by the T200 timeout is not measured as a call drop. If this parameter is set to 1,
the call drop caused by the T200 timeout is measured as a call drop.
To indicate whether a repeater is present. This parameter influence the handover between the repeaters. For repeaters that are far
away from each other should have asynchronous handovers, otherwise handovers will be failed.
To indicates the delay time after the cell initialization to detect whether the TRX mutual-aid function is enabled. To delay detecting
whether the trx mutual aid function is enabled because the cell that has been initialized is not in the stable state.
To indicate whether the flow on Abis interface is allowed. When BSS is congested some requests are rejected or delayed to
decrease the system load. This function applies to call management.
To indicate whether half rate is supported in the cell or not. It is one of the cell re-selection parameters in system message 3.
This parameter indicates the maximum transmit power level of MSs. It is one of the cell re-selection parameters in system message
3.
This parameter indicates whether the power control function is allowed. It is one of the cell selection parameters in system
message 3.
---
To indicate the interval between the transmission of an overload message and the retransmission of the overload message from
the BTS to the BSC
TO indicate the load on CCCH timeslot. Overload message is sent to the BSC by BTS if the load on CCCH is greater than this
threshold.
To indicates the interval between the transmission of a load message and the retransmission of the load message. Used by BTS to
inform the BSC about the load on the CCCH timeslot.
Used by BTS to inform the BSC of the interference levels on the idle channels of a TRX. This parameter indicates the period of
sending the RF Resource indication message.
This parameter indicates the value of frequency adjustment. The parameter consists of 16 bits. The most significant bit indicates
whether the parameter is valid. Bits 14-8 indicate the level threshold. Bits 7-0 indicate the BER threshold.
If this parameter is set to Yes, the BTS calculates the speed of the MS with the BTS as the reference object and reports the speed in
the uplink measurement report to the BSC. The value Yes is used for deciding whether to initiate quick cell switchover.
This parameter is used to detect whether the antenna feeder system connecting the TRX is faulty. Smaller the value, smaller will be
the error and vice versa.
This parameter is used to detect whether the antenna feeder system connecting the TRX is faulty. Smaller the value, smaller will be
the error and vice versa.
Indicates the threshold of the error and triggering condition for the generation of alarm. If the output power of a trx of a
transmitter is lower than a fixed value, an error is generated. Greater the value, smaller the error and vice versa.
Indicates the threshold of the error and triggering condition for the generation of alarm. If the output power of a trx of a
transmitter is lower than a fixed value, an error is generated. Greater the value, smaller the error and vice versa.
This parameter is used for BTS 2X to compensate the difference between the RSSI when the TMA is installed and the RSSI when the
TMA is not installed and to ensure the accuracy of the RSSI value when BTS 2X has no TMA. For other BTS version, this parameter is
not used.
To indicate the start frame number of the BTS. To Keep synchronization between MS and BTS after BTS is re-initialized.
This parameter indicates the maximum number of levels that the BTS RF power decreases. It controls the reduction in the BTS RF
power. Higher this value, lower will be BTS RF power and vice versa.
Before the BTS transmits the radio resource indication message to the BSC, the interference levels measured on idle channels in the
period defined by this parameter are averaged.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
This parameter indicates the threshold used for the interference measurement. The BSS measures the uplink quality of the radio
channels occupied by the serving MSs, calculates, and reports the interference level for each of the idle channels. This helps the
BSC to assign channels. The measurement result of the interference bands helps to set variable thresholds and analyze the
interference.
If the parameter Assignment Cell Load Judge Enabled is set to Yes, the direct retry process is started and channels are assigned
when the cell supports direct retry and the load of the current cell is equal to or greater than the value of Cell Direct Try Forbidden
Threshold during channel assignment.
Short message of cell broadcast DRX mode. Here, DRX means SMSBC DRX MODE (cell broadcast short message incontinuous
receiving mode). BSC supporting SMSBC DRX must send scheduling message for MS to receive cell broadcast messages
incontinuously. A scheduled message includes many broadcast messages to be sent in a cell. The duration occupied by the
broadcast messages in scheduled message is called scheduled period. The scheduled message includes both the description of
short messages (arranged in the order of transmission sequence) to be broadcasted and their respective positions in the scheduled
period. Therefore, MS can fetch the wanted broadcast message in the least time, and the power consumption is also decreased.
Indicates the types of data services supported. This parameter is set according to the requirements
If this parameter is set to StartUp, the BSC sends the handoff command to the MS and adjusts the transmission power of the BTS to
the maximum. During the handoff, the BSC does not change the BTS power to ensure the handoff success.
This parameter controls whether the BTS reports the voice quality index (VQI). Voice quality becomes better as the voice level
decreases.
In the BTS3002C, the signals transmitted through the primary and secondary antennas are optimized by the low noise amplifier
(LNA) bypass circuit. The BTS3002C supports the configuration
Maximum of diversity
value antennas. That is, the main diversity signals transmitted
of N3105.
on a DRU are treated by the LNA circuit and then connected to the diversity port of another DRU through a tributary.
After the a downlinkMaximum value of N3103.
TBF is established, the network starts N3105.
IfAfter
the network receives theRRBP
last RLC data block when Maximum value of N3101.
the network set the
GPRS GSN on the
provides downlink
subscribers withthe
RLC datauplink
block,
flexible transmission
QoS it mechanism.
resets N3105 is complete,
when
The it sends
QoSreceiving
level athe MS
valid a Packet
packet
is determined Uplink Ack/Nack
acknowledgment
in the subscription. message
message on with
the
uplink RLC FAI=1 andadded
starts on
N3103.network side and the network resends the downlink RLC data
In data block
uplink corresponding
dynamic assignment tomode,
the RRBP. Otherwise,
multiple MSs can N3105
shareisone uplink thechannel if the downlink data blocks carry the USF value.
The QoS control parameters include the service block where
prioritythe RRBP
class, is set. class, delay class, and throughput class.
reliability
If the network does not receive a packet control acknowledgment message within scheduled time, N3103 is added on the network side and the
After the network starts to assign a USF valuenetworkto the uplink
resendsTBF (uplink
the Packet TBF is
Uplinkestablished),
Ack/Nack N3101 is started. The network waits for the uplink data
message.
During
by the
In version
sent MS When
negotiation
theV9R8, onthe N3105
thebuilt-in overflows,
of a QoS
PCU
reserved profile,
supports
uplink the
RLC network
anblock
MS
the can
PDCH starts
apply a T3195.
value
configured
corresponding in
to When
for each
the
the T3195
QoS
overlaid
USF. If the expires,
attribute.
subcell orthe
MS sends Aftercurrent
inathe TBFthe
receiving
underlaid
valid uplink isRLC
released
request
subcell, abnormally
from
block,and the MS,the
supports
N3101 the
is reset. network
handover
Otherwise,
negotiates a class for each attribute of each QoS profile
between
Upper thebased
N3101
limit ofison
overlaid the
added
the current
subcell
on
bandwidth and
the effective
the
network
for the GPRS
underlaid
side.
Poc resources.
subcell.
services. The network provides the negotiated QoS
When this counter overflows, the network startswith
profile T3169. When T3169
corresponding expires, the current TBF is released abnormally.
resource.
Value
The Pocrange: Handover
services from requirement
have a strict underlaid
When this subcellLower
counter
on limit ofsubcell,
to overlaid
overflows,
transmission thethe
delay. bandwidth
Handover
current
The network forfrom
uplink the TBF
shouldPoc
overlaidservices.
issupportsubcell
released to underlaid
abnormally.
the detection subcell,
of the Handover
Poc service typebetween
and take
underlaid subcell and overlaid subcell,
measures toand
reduce theNot
No handover Supported:
between
transmission Not
delay support
underlaid
to meet QoSrequirement
subcell
the Optimize
and overlaidofsubcell. the PocDefault
services.value: No handover between
The Poc services have a strict requirement on transmission underlaid delay.
subcell Theand network
overlaid should
subcell. support the detection of the Poc service type and take
ThePacket
GRLMassignment
detects the refers to measures
service the
type to reduce
assignment
carried in of the
thea received
packet Supported:
transmission
channel
message. Support
todelay
the
If theMS QoS
toservice
meet
on Optimize
thethe requirement
PACCH.
type is Poc,Packet of the Poc services.
assignment
the uplink/downlink involves only theGbrValue
bandwidth move-down of theby
required
uplink packet assignment. Tothe increase
ABQPthe Thisaccess
must parameter
be lowerrate of isMSs,
thanbased
theafteron the
upper uplink
thelimit
packet immediate
of theassignment
bandwidth assignment.
is moved
for the down to the BTS, the BSC reserves uplink
Poc services
Theresources
GRLM detects
for thethe service
BTS. The BTStypetranslates
carried inthe thedownlink
receivedacknowledgment
message. If the service message type sentis Poc,
by thetheMS uplink/downlink bandwidth
to obtain the channel GbrValue
request required
message, and by
To increase the access rate of MSs, the
assignsthethe
ABQP BSS
mustpre-assigns
be higher
reserved uplinkuplink
than TBFlower
the
resources resources limitMS.
to QoS
the to
of the
the
Then BTS. theWhen
bandwidth an MS
thesends
forsend
MSobtained
can Poc ablocks.
channel request, the BTS uses these
dataservices.
When both the MS and the network support PFC, the parameters are
pre-assigned resources to send the immediate assignment message to the MS. After receiving the immediate assignment message, the MS can from the ABQP in the PFC.
send data blocks. The BTS also sends a secondary channel Default request
MCS type message
used on tothethedownlink.
BSC. After receiving this request message, the BSC sends a
When the MS or the networksecondary does not support
immediate PFC,assignment
the QoS parameters
message toare the obtained from the the
BTS to complete DL UNITDAT of the SGSN or from the uplink request
TBF establishment.
MCS type fixedly usedMS.
of the on the downlink.
If Downlink Fixed MCS Type is set to UNFIXED, you need to set this parameter to determine the MCS type for transmitting the first TBF. The MCS
types of the
To fixedly useother
a MCSTBFstypeareon dynamically
the downlink, adjusted
setused onparameter
this thethe basis of the signalamong
transmission quality.
During the data transmission process, the modulation Default
scheme MCS type
and coding on
scheme can betochanged
uplink. a value MCS1-MCS9.
to dynamically adapt to the radio transmission
environment,MCS type thus improving
fixedly used on thethe quality
uplink. of links.
If Uplink Fixed MCS Type is set to ToUNFIXED,
dynamically youadjust
need the to setMCSthistype on the downlink,
parameter to determine set this
the parameter
MCS type for to transmitting
UNFIXED. the first TBF. The MCS types
Tooffixedly
the other useTBFs
a MCS aretype
dynamically
on the uplink,adjusted
- Setting on
set thisand the basis of the
effect
parameter to asignal
value transmission
among MCS1-MCS9. quality.
Average period of bit error probe.
Link Adaption (LA): The network dynamically
To dynamically adjusts
adjust the thecoding
MCS type scheme on theof auplink,
channel setbased on the transmission
this parameter to UNFIXED. quality of the channel link. The link
This parameter
quality is determined by 8PSK canMEAN
be used BEPtoand obtain
8PSKthe CVforgetting
BEP carried factor,
in the which
Packet is used
EGPRS forDownlink
the MS to calculatemessage.
Ack/Nack the measurement
The networkresults.
selects a proper
Retransmission rate threshold for the downlink TBF to change
coding scheme for transmission based on the measurement reports from the MS. For cells with good Um interface quality, the LA mode is usually from CS4 to CS3.
Retransmission rate threshold fororthe used.
downlink
When the retransmission rate of the downlink TBF is greater than equal to theTBF value to ofchange from CS3 to
this parameter, theCS2.
coding scheme of the downlink TBF
Incremental Redundancyrate (IR):ofThe network should changes from CS4 to CS3.
When the retransmission Retransmission
the downlink TBF isretransmit
rate threshold
greater only
than different
fororthe equal todata
downlink theTBF blocks
value to of with
thisthe
change puncturing
from
parameter,CS2 to the coding
codingscheme.
CS1. scheme of ThetheMSdownlink
buffers the
TBF
history error information and the data blocks are retransmitted through
changes fromcombined
CS3 to TBF error correction. In the cell with bad Um interface quality, the IR
CS2.
modethe
When canretransmission
achieve good transmission Retransmission
quality, but
rate of the downlink rate
TBFthe threshold
MS must
is greater than for
supportthe
or equal downlink
thistomode.
the value to change
For cells
of this with from CS3 to
bad Um interface
parameter, CS4.
the coding quality,
scheme theofIRthe
mode is usually
downlink TBF
changes used.
from CS2 to TBF CS1.to change from CS2 to CS3.
When the retransmission rate of the Retransmission
downlink TBF rate threshold
is smaller than fororthe downlink
equal to the value of this parameter, the coding scheme of the downlink TBF
Retransmission rate threshold changesfororthe from CS3 to TBF
downlink CS4.to change from CS1 to CS2.
When the retransmission rate of the downlink TBF is smaller than equal to the value of this parameter, the coding scheme of the downlink TBF
When the retransmission rate of the downlink TBF is smaller Defaultchanges
CS type
than
from
usedCS2
or equal on to CS3.
the
to the downlink.
value of this parameter, the coding scheme of the downlink TBF
CS type fixedly from
changes used CS1 on the downlink.
to CS2.
If Downlink Fixed CS Type is set to UNFIXED, you need to set this parameter to determine the CS type for transmitting the first TBF. The CS types of
the otherYou TBFs areset
can dynamically
this parameter adjusted on theuse
to fixedly basisa CSoftype
the signal
on thetransmission
downlink. quality.
Retransmission rate threshold for the uplink TBF to change from CS4 to CS3. When the retransmission rate of the uplink TBF is greater than or
equal to To Retransmission
thedynamically
value of thisadjust ratethe
parameter, threshold
CS the for
on the
typecoding uplink
thescheme
downlink, TBF
of the to change
set from
this parameter
uplink TBF CS3totoUNFIXED.
changes CS2. CS4 to CS3.
from
Retransmission rate threshold for the uplink
When the retransmission rate of the uplink TBF is greater than or equal to the value of this parameter, the TBF to change from CS2 to CS1.coding scheme of the uplink TBF
changes from CS3 to CS2.
When the retransmission rate of the uplink TBF is greater than or equal to the value of this parameter, the coding scheme of the uplink TBF
Retransmission rate threshold for the uplink TBF to changechanges from CS3 to CS4.
from CS2 When
to CS1. the retransmission rate of the uplink TBF is smaller than or
equal to theRetransmission rate threshold
value of this parameter, for the
the coding uplink
scheme TBF
of the to change
uplink TBF from CS2 to from
changes CS3. CS3 to CS4.
Retransmission rate threshold for the uplink
When the retransmission rate of the uplink TBF is smaller than or equal to the value of this parameter, the TBF to change from CS1 to CS2.coding scheme of the uplink TBF
Defaultchanges
CS type from CS2
usedtoon to CS3.
the uplink.
When the retransmission rate of the uplink TBF is smaller than or equal the value of this parameter, the coding scheme of the uplink TBF
Timer set
CS type to
changes release
fixedly used
from the
CS1onAbis
tothe timeslots.
CS2.uplink.
If Uplink Fixed CS Type is set to UNFIXED, you need to set this parameter to determine the CS type for transmitting the first TBF. The CS types of the
other TBFs Youarecan setWhen
dynamically a adjusted
channel to
this parameter isonidle,
thethis
fixedly basistimer
use of
a CS istype
the started.
signalontransmission
the uplink. quality.
Level of dynamicTimer
Number channel
set to
of preemption
release
channels the idle
reserved bydynamic
CS
for services
CS and PS services
channel.
services.
To dynamically When the timer
adjust the CSexpires,
type onthe theAbis timeslots
uplink, set thisare released.to UNFIXED.
parameter
If an dynamicIn channel Full-rate TCHs are the dynamic channels that canunderlaid
beapre-empted.
If this parameter is set to an excessive value, the idle Abis timeslotstimer
a is
concentricno
If longer
this
cell, used,
parameter
the it
overlaid is
is not
set toreleased
subcellan immediately.
excessive
uses DCS1800 value, the
and Instead,
PS
the services are isaffected.
started
subcell
cannot useswhen
be fully the channel is idle.
GSM900.
utilized.
thisAll
BeforeIfthe dynamic
timer
parameter channels
Ifexpires,is ifset
this parameter to acan
there are be
new
modest
is set
pre-empted:
PDCH
to avalue,
modest
The
downlink
services,
thethe
CS CS services
multiplex
dynamic
services
Value
value, are
range:
the Abis
can continues
pre-empt
threshold
channel
affected
timeslots when
may be
all theare
dynamic
toapplied
be
there used and
too channels.
the
many timer is stopped.
PS services
frequently.
Control channels
If this parameter is set tocannot
a lowerbevalue,
pre-empted:
theWhenTBFsThe CS PDCH
services
established
the timer uplink
on can
the
expires, multiplex
pre-empt
PDCH
the and
dynamic threshold.
all
thethe dynamic
subscribers
channel channels
are fewer,except
is released. and thefordownlink
the control channels.for each
bandwidth
Convert dynamic channel in underlaid subcell.
subscriber is higher.
If If
this parameter
Dynamic channels
this parameter is set to a lower
carrying
is set value,
to anservices
excessive the
cannot TBFs
value,be theestablished
pre-empted:
dynamic on the PDCH
Thechannel
channel CSresources
servicesand the
cannot
may besubscribers
pre-empt are
wasted when fewer,
the dynamic and the uplink
there arechannels bandwidth
thatfor
no services carry for each
services.
a long time.
Convert dynamicsubscriber in overlaid
is and
higher. subcell.
If this threshold is set to a higher value, the TBFs established on the PDCH the
Downlink multiplex threshold of dynamic channel conversion. subscribers are more, and the downlink bandwidth for each
If this parameter is set to a modest value,dynamic
it is possible thatin asubscriber
dynamic is lower.
channel andisthe requested immediately after being released. Therefore, the
If this threshold is set to a higherConvert
value, the
UplinkTBFs channel
established
dynamic channel
multiplex
both
on
threshold thesubcells
PDCH
request
of dynamic and underlaid
is sentchannel
frequently.
subcell
subscribers preferred.
are
conversion. more, and the uplink bandwidth for each
When the number of subscribers reaches
subscriberthis threshold,
is lower. the dynamic channels are used.
Value 10 indicates
Convert a maximum
dynamic channel of one
in both TBF
subcells can
andbe established
overlaid onpreferred.
subcell the PDCH.
Multi-frequency reporting.
When the numberIf this of subscribers
threshold is reaches
high, it is this threshold,
difficult to seize the dynamic
dynamic channels are used.
channels.
Value
The totalValue
number10 indicates
of TCHs and
80 indicates a maximum of
PDCHs isoffixed.
a maximum one
eightTheTBF
TBFs can
PDCH be
can be established
ratio on
onthe
thePDCH.
equals PDCHs/(TCHs
established + PDCHs).
PDCH.
Value range:
If this
If threshold
this thresholdis high,
is low,it is
it difficult
is easy to to seize
seize dynamic
dynamic channels.
channels
Value 70 indicates
If this parameter is set to an excessive value, a maximum of seven
there areofexcessive TBFs can
PDCHs be established on the PDCH.
and insufficient TCHs. This affects CS services.
Normal reporting ofThresholdthe six strongestHCS signal strength.
cells respective of the band used.
If this threshold is low, it is easy to seize dynamic channels.
IfThe
thisMS
parameter
uses the issignal
set tostrength
a modest in value,
the MR there
and are
this insufficient
threshold toPDCHs and C31,
calculate excessive
whichTCHs. This affects PS services.
The MS shall report the strongest cell in each of the frequency bands inisthe
used
BAfor cell reselection.
lists.
If the
The MSthreshold of the
shall report HCStwo
signal strengthcell
strongest is high, it isofdifficult
in each for the cell
the frequency bandsto be selected.
in the BA lists.
If the
The MS threshold
shall of HCS
report the signal
three strength
strongest cellisinlow,
eachit of
is easy for the cellbands
the frequency to be in
selected.
the BA lists.
HCS priority of a GPRS cell.
If the priority is high, it is easy for the MS to select this cell during cell reselection.
Maximum TX power level for an MS to access the packet control channel.
Minimum
If the priority is low,RXit power
is difficultlevelfor fortheanMS MSto in select
the cell thisto cell
access the cell
during system.reselection.
If this parameter is set to an excessive value, the power consumption and radiation of the MS are high.
If this parameter is set to an excessive value, the coverage area
0: lowest of theaccess
priority;
Exclusive cell
7: ishighest
large.
or not.The MS on the edge of the cell may not be able to access the
priority
If this parameter is set to a modest value,system. the MS may not be able to access the channel.
Whether the cell Exclusive: exclusive access. reselection.
can be accessed during cell
If this parameter is set to a modest value, the coverage area of the cell is small. The usage of cell resources decreases.
Hysteresis of cell reselectionisinpermitted.
Permit:access different routing areas.
NoExclusive: No exclusive access.
When an MS in the ready state performs cell reselection,NoPermit: Period when cell
if the originating reselectioncell andis prohibited.
the target cell belong to different routing areas, the MS starts
access is prohibited.
cell reselection only when the signal level of the neighbor Whether cells in
thethe different
MS period
can access routing areas cell.
another is higher than that of this cell, and when the signal level
If this parameter is setdifference to a higher value,
is greater than the value of this when cell reselection
parameter. is prohibited increases.
Whether GPRS_RESELECT_OFFSET is used
Yes: value,
The MSthe for C32
canperiodcalculation
accesswhen another duringcell. cell reselection Value range: 0, 1.
If this parameter is set to a lower
Hysteresis of cell reselection in the same cell reselection
routing area. is prohibited decrease
Whether GPRS Cell Reselect
0: GPRS_RESELECT_OFFSET is MS Hysteresis
not cannot
used foraccess
C32 is applied
calculation to the C31 cell
during standards.
reselection.
No: The another cell.
When an MS in the ready state performs cell reselection, if the originating cell and the target cell belong to the same routing area, the C2 value
measured in the overlapped area of two adjacent cells fluctuates
1: GPRS_RESELECT_OFFSET c31standard:
is usedgreatlyfor C32applied.
because
calculation of the fading
during cellfeature of radio channels. Therefore, the MS
reselection.
frequently performs cell reselection. The frequent cell reselection
Whether the PSInot onlymessage
status increasesisthe signaling flow on the network and affects the utilization of
supported.
radio resources, but also greatly affects the datac31notuse: transmission notrate applied.
of the MS and decreases the QoS as a consequence.
Whether the measurement report command is allowed.
Yes: supported
When this parameter is used, the MS starts cell reselection Persistence onlylevelwhen4 the signalpriority
level ofaccess.
the neighbor cells in the same routing area is higher than
Repetition period ofofthe radio
PS information PSI1. If this parameter is set to an excessive value, it is
that of this cell, and when the signal level difference is greater No:Yes:
than the
not allowed.
value
supported of this parameter.
A priority is set before anIf MS Persistence hard to
level start
3 ofcell
radioreselection.
priority access.
thisaccesses
parameter theiscell. If the
set to priority is value,
an excessive higherthe
No: not
than PSI1
allowed.
themessage
persistence cannotlevel,
bethe MS can
received in access the cell. Otherwise, the MS
real time.
Persistence cannot 2access thepriority
cell. access.
A priority is set before an MS accesses the cell. If the priority islevel higher of
thanradio the persistence level, the MS can access the cell. Otherwise, the MS
If this parameter is set to a modest value, the PSI1 access
cannot message the iscell.
sent frequently. This occupies many resources.
A priorityIf this
is setparameter
before anisMS setaccesses
to an excessive
the cell.value,
If the itpriority
is difficult
Persistence islevelfor1anof
higher MS
thanradio to
theaccess
priority
persistencethe cell.
access. Therefore,
level, the MSradio resources
can access may Otherwise,
the cell. be wasted. the MS
If this parameter is set to an excessive value, it is cannot
difficult for access
an MS the
to cell. the cell. Therefore, radio resources may be wasted.
access
If this parameter
A priority is setisbefore
set to ana modest
MS accesses value,aitcell.
is easy
If theforpriority
an MS to access than
is higher the cell. the However,
persistence toolevel,
many theMSs MSmaycan access
access the
the cell.
cell. Therefore,
Otherwise,the
thesystem
MS
If this parameter may
cannot beaccess
overloaded.
the cell.
If this parameter is set to aismodest
set to an excessive
Minimum
value, value,
number
it is easy for itan isMS
of difficult
timeslots
to accessfor anthe
between MScell. to
two access thetoo
successive
However, cell. Therefore,
channel
many MSs radio
requests.
may resources
access may
the cell. be wasted.
Therefore, the system
If this parameter may beanoverloaded.
IfThe
thisMSparameter
sends anisaccess aismodest
set toand
set to request an excessive
value,
waits it for
Number avalue,
isMaximum
easyoffor
response.itanisMS
timeslots
difficult
number to of
foraccess
If no for
response
extension theMS
retransmissions to access
iscell. However,
received
transmission
thetoo
forafter
radio cell.
in the
Therefore,
priority
many
minimum
random
4. may
MSs
access.
radio
number resources
access may
the cell.
of timeslots, be wasted.
Therefore,
the the system
MS resends the
may be overloaded.
access request.
If this parameter is set to a modest value,Value it isMaximum
easy for an
1 indicates number
MS of
thetomaximum retransmissions
access thenumber offor
cell. However, radio toopriority
retransmissionsmany MSs 3.is 1.may access the cell. Therefore, the system
If this parameter is set to an excessive value, the MS needs may be
foroverloaded.
Value
Value
Maximum
1 indicates
2 indicates thetomaximum
number
the
wait
maximum a number
long time
of retransmissions
number of
before
offor radiosending
prioritythe
retransmissions
retransmissions
next request. This may affect MS services.
2.is 1.
is 2.
If this parameter is set to a modest value, Value Maximum
it is possible number
that the of
a response retransmissions
is made, butof for radio priority 1.
Value
Value
1
2 indicates
4 indicates
indicates the maximum
maximum number
number ofthe MS has not received
retransmissions
retransmissions is
is 1.2. it because of transmission delay. In this
case, thethe MSmaximum
also resends number of
the access retransmissions
request. is 4.
Value
Value 1 indicates
2 indicates the the maximum
maximum number number of retransmissions
of retransmissions is
is 1.2.
Value
Value 47 indicates
indicates the the maximum
maximum number number of of retransmissions
retransmissions is is 4.
7.
Number of PRACH blocks. Value range: 1-12.
Value
Value 2
4 indicates
indicates the
the maximum
maximum number
number of
of retransmissions
retransmissions is
is 2.
4.
Value 7 indicates the maximum number of retransmissions is 7.
Number of PAGCH blocks.one Value range: 1-12.
ValueAccess controlValue class;116-bitindicates bitmap; value PRACH. range: 0-65535. 4.
Value 47 indicates
indicates the the maximum
maximum number number of of retransmissions
retransmissions is is 7.
Number of PBCCH
Value21 indicates blocks.
indicatestwo Value
one PRACHs.
PAGCH. range: 1-4.
Value
Value 7 indicates the maximum number of retransmissions is 7.
Value21indicates
Value indicatestwo onePAGCHs.
PBCCH.
...
Minimum duration Periodwhen of cellthereselection
MS stays Valuein measurement
2non-DRX
indicates two report
PBCCHs. inthepacket transfer mode.report is sent.
Value 12 ... mode
indicates after
12 PRACHs. NC-measurement
Period
If this parameter of cell reselection
is set to measurement
an excessive value, report
some in packet
information idle
maymode. be missing.
The MS should stay in non-DRX Value
mode
Valuefor 312 indicates
aindicates
period three
of12 timePBCCHs.
after
PAGCHs. the measurement report is sent.
GPRS reselection
If this parameter is set to a modestIfvalue,If this offset
parameter is used
is set
the reselection to calculate
an excessive
measurement C32. A
value, higher
some
report value indicates
information
isservices
sent frequently. a
may higher
This occupiespriority.
be access
missing. many bandwidth resources.
this parameter Value
is set to 4 indicates
an excessivefour value,PBCCHs. may be affected.
If this parameter is set to a modest value, the Thereselection
principles of cell reselection
measurement offset
report are as
is sent follows: This occupies many bandwidth resources.
frequently.
If this parameter is set to a modest value, the MS may send the measurement report frequently.
1 Forthe
When theBCCH
cell with low traffic
frequency of aand
cell low equipment
is listed utilization,
in the neighbor Huawei
cells for therecommends that MSs
MS, the negative work
offset in the
of C2 cell. The value
is calculated beforerange
timer0-20dB is
T expires.
Timer used for the MS to calculate C32. The timer isRemarks
recommended.
sent through the system information broadcast in each cell.
None.
This parameter is set to avoid the ping-pong cellInterval reselection by the fast-moving MS. Therefore, the MS does not select this cell when the duration
of 2signal
For the cellbetween
strengthwith extension
on medium
the BCCHtraffic,
measurement
valuethan
is shorter 0 is thereports.
recommended.
penalty time.
If this parameter is set to a modest value, the extension measurement report is sent frequently.
Value infinity indicates an infinity offset.
IfFrequency
this parameter
type is in set
theto an excessive
extension value, measurement
measurement report. Valueinformation is not
range: type1, obtained
type2, timely.
and type3
Frequency index of the interference measurement. Value range: 0-31.
Whether MSs are permitted to report the NCC bitmap of measurement reports. 0-255 are the parameters of the NCC bitmap.
The network can require the MS to send measurement
Whether the reports. When
CS paging onthetheMS is in idleismode,
A interface it sends the extension measurement reports. This
supported.
parameterthe
This parameter determines canpriority
be set to of em0
packet or access
em1. of MSs to a cell.
Yes: The MS can receive Whether the 11-bit
CS paging on theEGPRS accesswhen
A interface is supported.
handling the GPRS service.
The values of this parameter are:
No: The MS cannot receive CS paging Yes: the
supported.
Routing areaon A interface
color code of a GPRSwhen handling the GPRS service.
cell.
No packet access.
Whether the cell supports No: notSPLIT_PG_CYCLE
supported on the CCCH.
Value range: 0-7. The parameter should be configured according to the requirements of the network operator.
In the cell reselection required by the network, the network requests the MSoftolevel
Packet access send 1.measurement reports to control its cell reselection. There are
SPLIT_PG_CYCLE defines the DRX period. Whether the BTS andnetwork
three MS supportcontrolthemodes.
SPLIT_PG_CYCLE-based paging group on the CCCH is optional.
Packet access of levels 1-2.
Yes: The
nc0: Normal cell supports
MS control. The MSSPLIT_PG_CYCLE
performs automatic on thecellCCCH.
reselection.
Pan Max.isPacket access
also the of levels
maximum 1-3.of N3102.
value
nc1: MS control with measurement No: The cell
MSdoes notmeasurement
support SPLIT_PG_CYCLE onnetwork
the CCCH. performs automatic cell reselection.
This parameter is used to set the valuereports.
of N3102.The When sends
the MS reportsUplink
receives a Packet to the Ack/Nack andmessage that allows V(S) or V(A) increase,
Value 4 indicates that Pan Max. is 4; value
N310232 is PacketPan
indicates
increased access
by Max.
the ofislevels
value 1-4.
32;ofvalue
this nouse indicates that this parameter is not used.
parameter.
nc2: Network control. The MS sends measurement Maximumreports countdown
to thevalue
networkof the
butMSdoes not perform automatic cell reselection.
This parameter is used to set the value of N3102. When T3182 expires, N3102 is decreased by the value of this parameter.
Value 0 indicates that
This Pan Increment
parameter is 0;for
is used value
the 7MS
indicates that Pan
to calculate Increment
CV. The parameteris 7; also
valuedetermines
nouse indicates thatof
the value this parameter is not used.
T3198.
Value 0 indicates thatacknowledgment
Control Pan Decrement istype.0; value
This7parameter
indicates that Pan Decrement
determines is 7; value nouse
the acknowledgment indicates
message typethat this
used byparameter
the MS. is not used.
Every time the MS sends an uplink RLC data block, it sets the receive state of the data block to Pending and starts T3198. If the MS receives a Packet
Uplink Ack/Nack messageIfbefore T3198pulses
four access expires,areitused,
updates thethe receive
timing statecan
advance of each uplink RLC
be obtained data block
without based
a polling on the acknowledgment bitmap
message.
contained in the message. If T3198 for the RLC data block in the Pending state expires, the MS sets the receive state of this data block to Nack and
If the RLC/MAC control block is used, the timing advance can be obtained resends it.by sending a polling message. Four access pulses are recommended.
only
Maximum duration of the non-DRX mode. DRX_Timer_Max (DRX: discontinuous reception) is a parameter carried by the cell broadcast message.
Access burst type used by the MS in the PRACH, PTCCH/U, and packet control acknowledgment message.
When the MS switches from the Timer set for
Timer
packet setthe
transferforMSthetoMS
mode wait for
totothewaittheforTBF
packet the release
idlePacket
mode, after
Uplink receiving
it stays Assignment the last
in non-DRX data for
message.
mode block.
a period of time. After the TBF is
released, the MS monitors all the CCCH blocks during the 8bit: accessmode
non-DRX using period
the 8-bit and burst.
the BSC6000 reserves the MS context. The reservation time
When
After theMS
the
depends MS receives
onsends thethe
the smaller last Resource
Packet
value RLC dataDRX_Timer_Max
among block
Request carrying
or Packettheandlast block flag
Downlink Ack/Nack
NON_DRX_TIMER. (FBI=1)message
and confirms
NON_DRX_TIMERcarrying that all
Channelthe RLC data
Request
is negotiated blocks
Description,
with on theT3168
the SGSN TBF are
during received,
isthe
started
GPRSto
the MS sends
attach of the the
MS Packet
and its Downlink
wait is
value Ack/Nack
forusually
the Packet
high. message
11bit: access
Uplink
Therefore, carrying
using
the the
Assignment the11-bit
final burst.
message
reservation acknowledgment
fromactually
time the network. flag (FAI=1)
depends and starts T3192.
on DRX_TIMER_MAX.
Based on the paging channel used by the system, the network operation modes are classified into Network Operation Mode I, Network Operation
IfWhen
the MS T3192 expires,
receives the MSUplink
the Packet releases the TBFValue
Assignment resources
message
0 and
before
indicates
Mode monitors
II, and T3168
entering
Network paging
expires, channels.
T3168
theOperation
DRX mode During
isimmediately.
Mode reset. the TBF release
III. Otherwise, the MS process,
initiates if the
the MS is in half-duplex
PS access procedure
mode and
again for four times. receives
If the Packet the
UplinkPacket Uplink Assignment
Assignment message iscommand, the MSthe
still not received, responds
MS regards to thethiscommand
uplink TBF immediately.
establishment as failure.
Value 1 indicates entering Whenthe the DRX
This mode
GSparameter
interfaceoneisissecond later.
configured,
usedduring
for Value
theNetwork
open n indicates
powerentering
Operation Mode Ithe DRX mode n seconds later.
is used.
If the MStimer
If the doesvalue
not receive
is short,the Packet
the Uplink
time for the Assignment
MS to decidecommand that a TBF the
establishment TBFloop
release control.
fails is process,
short. If athe TBFMS enters the packet
establishment idleaverage
fails, the mode. Ifdelay
the MS
of is
packet access is short, but the success Gsrate in dual transfer mode, itpower
enters the dedicated mode. Mode
When the
ALPHA is of TBF
interface
used establishment
or
for the
the PCCCH
MS isinnot
bad
Initial
to calculate radio
configured, environment
level.
the output Network
power on decreases.
Operation
the uplink In addition, the short timer value increases
II is used.
PDCH.
the probability of the retransmission of the packet access request, thus increasing the probability of reassignment by the PCU. Therefore, many
system
When the resources
This
MS are
parameter
uses wasted.
When
GPRS the IfGsthe
determines
dynamic timer
interface
power value
is notisconfigured
the expected
control, long,
receive
Signal the time
signal
strength
this parameter for
the
filterthe
but strength
PCCCH MS
length
determines to
on is
the decide
BTS
configured,
inthe
packet
reducedthat
side a TBFthe
idlewhen
Network
mode.
level ofestablishment
MSMS uses
Operation
the GPRS fails
Mode
transmit isIIIlong.
dynamic
power If a TBF
power
is used.
based establishment
control.
on the path loss.
fails, the average delay of packet access is long, but the success rate of TBF establishment in bad radio environment increases.
Signal
This strength
parameter filter
mainly length
affects in packet
the transmission
output power of mode.
the
This parameter is used when the MS measures the downlink signal strength in packet idle mode and calculates Cn of the MS output power. The MS.
parameter indicates the relation between Cn and Cn-1.
This parameter is used when the MS measures the downlink signal strength in packet transmission mode and calculates Cn of the MS output
Constant
power.
This parameter determines the channel of the
The interference
parameter
where the indicatessignal
receive strength
the
power levelfiltering
relation ofbetween
the MS by ispowerandcontrol.
CnmeasuredCn-1.for the uplink power control.
Remarks
None.