Beruflich Dokumente
Kultur Dokumente
GT-C3200L
1. Safety Precautions
2. Specification
3. Product Function
4. Exploded View and Parts list
5. MAIN Electrical Parts List
6. Level 1 Repair
7. Level 2 Repair
8. Level 3 Repair
9. Reference data
Notice
All functionality, features, specifications and o
ther product information provided in this docu
ment including, but not limited to, the benefit
s, design, pricing, components, performance,
availability, and capabiliti-es of the product
are subject to change without notice or oblig
ation. Samsung reserves the right to make
changes to this document and the product
described herein, at anytime, without
obligation on Samsung to provide notification
of such change.
5. MAIN Electrical Parts List
5-1
5-2
5-3
5-4
5-5
5-6
5-7
Loosen screws
3 4
Separate
window
7-1
7-1-2. Assembly
1 2
1) Assemble LCD and window with FRONT. 1) Place keypad at the FRONT.
Caution Caution
1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage!
3 4
1) Put PBA and connect LCD. 1) Assemble rear and joint screws at 4 points.(toque 1.2)
Caution Caution
1) Be careful not to make scratch and molding damage! 1) Be careful not to make scratch and molding damage!
7-2
8-1
HY20-AB0310
3710-002683
IFC400
8-2
8-2-1. Bottom
8-3
8-3-1. Power On
Yes
Yes
Yes
Yes
END
8-6
8-7
8-8
8-3-2. Initial
Initial Failure
Yes
Yes
No
UCP200 pin D2 > 1.7V ? Change PBA to check TP_RST.
(TP:TP_RST)
Yes
Yes
END
8-9
8-10
8-11
Yes
Yes
No Resolder R309
R309 > 4.9V ?
(be possible that it's not soldering well)
Yes
Yes
END
8-12
8-13
Yes
Yes
Yes
Yes
Yes
END
8-14
8-15
Yes
Yes
Yes
Yes
END
8-16
8-17
Yes
L407, L408
> 2.0 V No Resolder L407 & L408
(Wiring the SPK N/P and
checking an waveform using (be possible because of soldering not well)
oscilloscope)
Yes
No
Does not work Voice call ? Replace UCP200 using a Heatgun
(be possible of being UCP a bad sample)
Yes
Yes
Yes
END
8-18
8-19
Yes
Change Domesheet
When you pushed all of the (#1 : look over the Dome situation
No whether be sunken
Key, does the key have
tension? #2 : look over the Dome location
whether be out of line)
Yes
Yes
END
8-20
8-21
Yes
Yes
Yes
END
8-22
8-23
Yes
Yes
Yes
END
8-24
8-25
RX ON
Cell Power : -60dBm
Yes
PAM100 Pin17
-65dBm No Resolder PAM100, L113,C102,
(TP:L113 using L100
spectrum analyzer)
Yes
PAM100 Pin11
-68dBm No Check PAM100 No Check ANT Switch
(TP:L108 using pin5=L, pin6=L control circuit
specturm analyzer)
Yes
Resolder PAM100
Yes
Yes
Check UCP200
Yes
END
8-29
RX ON
Cell Power : -60dBm
Yes
PAM100 Pin17
-65dBm No Resolder PAM100, L113,C102,
(TP:L113 using L100
spectrum analyzer)
Yes
PAM100 Pin12
-68dBm No Check PAM100 No Check ANT Switch
(TP:L109 using pin5=L, pin6=H control circuit
specturm analyzer)
Yes
Resolder PAM100
Yes
Yes
Check UCP200
Yes
END
8-30
RX ON
Cell Power : -60dBm
Yes
PAM100 Pin17
-65dBm No Resolder PAM100, L113,C102,
(TP:L113 using L100
spectrum analyzer)
Yes
PAM100 Pin13
-68dBm No Check PAM100 No Check ANT Switch
(TP:L110 using pin5, pin6=H control circuit
specturm analyzer)
Yes
Resolder PAM100
Yes
TCXO CLOCK
No
CHECK? Resolder OSC201
26MHz @ OSC201
Yes
Check UCP200
Yes
END
8-31
RX ON
Cell Power : -60dBm
Yes
PAM100 Pin17
-65dBm No Resolder PAM100, L113,C102,
(TP:L113 using L100
spectrum analyzer)
Yes
PAM100 Pin14
-68dBm No Check PAM100 No Check ANT Switch
(TP:L111 using pin5=H, pin6=L control circuit
specturm analyzer)
Yes
Resolder PAM100
Yes
TCXO CLOCK
No
CHECK? Resolder OSC201
26MHz @ OSC201
Yes
Check UCP200
Yes
END
8-32
8-33
8-34
YES
PAM100 pin27 -4 NO
dBm Re-solder or change
(TP:R106 using UCP200
spectrum analyzer)
YES
NO
Check the Voltage Check the UCP200 & VBAT
C106 < 3.3V? circuit.
YES
PAM100 Pin17 NO
30dBm Resolder PAM100
(TP:L113 using
spectrum analyzer)
YES
NO
Check the RFS100
connection with PCB? Resolder RFS100.
YES
Antenna
re-solder or change
8-35
YES
PAM100 pin29 -4 NO
dBm Re-solder or change
(TP:L116 using UCP200
spectrum analyzer)
YES
NO
Check the Voltage Check the UCP200 & VBAT
C106 < 3.3V? circuit.
YES
PAM100 Pin17 NO
30dBm Resolder PAM100
(TP:L113 using
spectrum analyzer)
YES
NO
Check the RFS100
Resolder RFS100.
connection with PCB?
YES
Antenna
re-solder or change
8-36
8-37
8-38
- NC Point(Top View)
: NC
U101
1 2 3 4 5 6 7
UME200
1 2 3 4 5 6 7 8 9
8-39
UCP200
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
8-40