Beruflich Dokumente
Kultur Dokumente
The Lumentum Tunable SFP+ Optical Transceiver is a full duplex, integrated fiber optic
transceiver that provides a high-speed serial link at 9.95 to 11.3 Gbps signaling rates. The
transceiver supports the enhanced small form factor pluggable module (SFP+) specification
SFF-8431 Rev. 4.1 for the electrical interface, SFF-8432 Rev. 5.0 for the mechanical interface,
SFF-8690 Rev. 1.4 for the tunability interface, and SFF-8472 Rev. 11.0 for the
management interface.
The transceiver complies with IEEE 802.3-2012 clause 52 and it Key Features
supports 10GBase-ZR/ZW (Ethernet), 10 G Fibre Channel (FC), Supports 9.95 to 11.3 Gbps line rates
and corresponding forward error correction (FEC) rates. It SFF-8431 MSA Revision 4.1 compliant
supports Telcordia GR-253-CORE OC-192 LR-2 and ITU-T G.959.1
SFF-8690 MSA Revision 1.4 compliant
P1L1-2D2 data rates.
Full C-band tunable laser source
It integrates the receive and transmit path on one module. On the 50 GHz ITU channel spacing
transmit side, the serial data stream is passed from the electrical 80 km reach
connector to a modulator driver. The modulator driver biases and
Operating temperature range of 5 to 70C
modulates a C-band cooled tunable transmitter, enabling data
transmission over up to 80 km of single-mode fiber through an Maximum power dissipation of 1.7 W
industry-standard LC connector. On the receive side, the 10 G RoHS6/6 compliant
optical data stream is recovered from an avalanche Linear SFI AC-coupled electrical output interface
photodetector (APD) through a transimpedance amplifier to the
Supports digital diagnostic monitoring
electrical connector. This module features a hot-pluggable
SFI-compliant linear electrical interface.
Applications
Wide area networks (WAN)
Local area networks (LAN)
Storage area networks (SAN)
Ethernet switches and applications
FC switches and applications
Compliance
IEEE 802.3-2012 clause 52 standard
10 G FC standard
SFF-8431 Rev 4.1
SFF-8432 Rev 5.0
SFF-8472 Rev 11.3
SFF-8690 Rev 1.4
Class 1 laser safety
Tested in accordance with Telcordia GR-468
ROHS 6/6
www.lumentum.com 2
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
RS1 MOD_ABS
Low-Speed Interface
Connections Definition
Figure 1. Lumentum tunable SFP+ optical transceiver functional
block diagram SCL/SDA 2-wire serial interface clock and data line.
Tx_Fault Output pin. When asserted high, indicates that the
The transceiver has several low-speed interface connections. module has detected a transmitter fault condition
These connections include: transmitter fault (Tx_Fault), related to laser operation or safety.
transmitter disable (Tx_Disable), module absent (Mod_ABS), Tx_Disable Input pin. When asserted high or left open, the
receive loss of signal (Rx_LOS), and a 2-wire serial interface transmitter output is turned off. When Tx_Disable
clock (SCL) and data (SDA). Rate select (RS0 and RS1) is not used is asserted low or grounded, the module
in this product. transmitter is operating normally.
RS0 and RS1 Input pins. These pins are not used in this product.
The transceiver supports the SFI electrical interface. Mod_ABS Output pin. Asserted high when the SFP+ module
The electrical interface is based on a high-speed, low-voltage is absent and is pulled low when the SFP+ module
logic AC-coupled linear interface with a 100 nominal is inserted.
differential impedance. Rx_LOS Output pin. Asserted high when insufficient
optical power for reliable signal reception is
received.
www.lumentum.com 3
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
Tunable SFP+ modules are hot pluggable and active connections are powered by individual power connections for the transmitter (VCCT)
and the receiver (VCCR). Multiple modules can share a single 3.3 V power supply with individual filtering for each VCCT and VCCR. The host
shall generate an effective weighted integrated spectrum RMS noise of less than 25 mV in the 10 Hz to 10 MHz frequency range.
Detailed power supply specifications are given in SFF-8431 Rev. 4.1 Section 2.8. Figure 2 shows a typical application schematic.
www.lumentum.com 4
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
Section 3.9 OSNR Characteristics with External EDC 4 LVTTL- SDA2 2-wire interface data line
I/O
Section 3.10 Tunable SFP+ Channel Number and Wavelength
5 LVTTL-I SCL2 2-wire interface clock
Section 3.11 SFP+ 2-wire Interface Protocol and 6 Mod_ABS2 Indicates module is not present.
Management Interface Grounded to VEET or VEER in the module.
Section 3.12 Digital Diagnostic Monitoring Accuracy Asserted high when SFP+ module is
absent and pulled low when the SFP+
Section 3.13 Timing Requirement of Control and Status I/O
module is inserted.
Section 3.14 Timing Diagram for Power-On/Hot-Plug and 7 LVTTL-I RS03 Rate select 0 (not used)
Tx_Disable
8 LVTTL-O Rx_LOS2 Receiver loss of signal indicator. Asserted
Section 3.15 Regulatory Compliance high when receiving insufficient optical
Section 3.16 T-SFP+ Transceiver Mechanical Diagram power for reliable signal reception.
9 LVTTL-I RS13 Rate select 1 (not used)
3.1 Pin Function Definitions 10 VEER 1
Module receiver ground
11 VEER1 Module receiver ground
RS0 7
14 VEER 16 VCCT Module transmitter +3.3 V supply
MOD_ABS 6
15 VCCR 17 VEET1 Module transmitter ground
SCL 5
16 VCCT 18 CML-I TD+ Transmitter non-inverted data input
SDA 4
17 VEET 19 CML-I TD Transmitter inverted data input
Tx_Disable 3
18 TD+ 20 VEET1 Module transmitter ground
Tx_Fault 2
19 TD
VEET 1 1. Module ground pins (GND) are isolated from the module case and chassis ground
20 VEET within the module
2. Shall be pulled up with 4.7 to 10 k to a voltage between 3.135 and 3.465 V on
the host board
3. Pulled high to VCCT with >100 k in the module
Figure 3. Tunable SFP+ optical transceiver host board pin assignments
Tx_Disable
D C' C
GND VEER
Mod_ABS
GND VEET
SCL/SDA
Tx_Fault
Rx_LOS
2 Rx
Connector
RS0
RS1
ASIC/
SFP+ Module
SERDES
Tx
2
TD +/
SFP+ Module A B' B
2
RD +/
www.lumentum.com 5
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
1. Vcc_host (min) 3.135 V (max) 3.465 V 3. PRBS31 or valid 64B/66B, 10.3 Gbps
2. PRBS9 pattern, 10.3 Gbps 4. PRBS31 pattern, BER<1x10 -12, 10.3 Gbps
www.lumentum.com 6
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
Data Rate (Gbps) BER Dispersion (ps/nm) Min Max OSNR (dB)
9.95, 10.3, 10.5 1x10-12 0 19 7 24
9.95, 10.3, 10.5 1x10 -12
400 to +1600 19 7 26
10.709 1x10-4 0 19 7 15.5
10.709 1x10-4 400 to +1600 19 7 17.5
11.1 1x10-4 0 19 7 16
11.1 1x10-4 400 to +1600 19 7 18.5
1. Optical power and wavelength range are only guaranteed when the electrical input applied to TD+ and TD is greater than the minimum specified in Section 3.6
2. Tested with a PRBS 2311 pattern
3. ITU grid wavelength in Section 3.14
4. At 20 dB, 0.01 nm RBW
5. Minimum optical return loss at the source reference point, MPI-S (per ITU-T G.959.1)
6. Maximum discrete reflectance between source reference point, MPI-S, and receive reference point, MPI-R (per ITU-T G.959.1)
7. Receiver LOS assert level (per average power) is programmable upon request.
8. Measured with worst ER; PRBS 2311; over specified wavelength range; OSNR >30 dB; with external electronic dispersion compensation (EDC)
9. Specifications apply under these conditions:
www.lumentum.com 7
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
www.lumentum.com 8
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
www.lumentum.com 9
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
3.14 Timing Diagram for Power-On/Hot-Plug and Tx Disable Event (Not to Scale)
www.lumentum.com 10
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
www.lumentum.com 11
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
www.lumentum.com 12
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
Housing
The transceiver housing is made from zinc. Caution
Operating this product in a manner inconsistent with
intended usage and specifications may result in hazardous
4.2 Electrostatic Discharge
radiation exposure.
Handling
Normal electrostatic discharge (ESD) precautions are required Use of controls or adjustments or performance of procedures
during the handling of this module. This transceiver is shipped in other than these specified in this product data sheet may result
ESD protective packaging. It should be removed from the in hazardous radiation exposure.
packaging and otherwise handled in an ESD protected
environment utilizing standard grounded benches, floor mats, Tampering with this laser product or operating this product
and wrist straps. outside the limits of this specification may be considered an act
of manufacturing and may require recertification of the
modified product.
www.lumentum.com 13
Tunable SFP+ Optical Transceiver with Linear Electrical Interface
This equipment has been tested and complies with the limits for a Translation: This is a Class B product based on the standard of the
Class B digital device, pursuant to Part 15 of the FCC Rules. These Voluntary Control Council for Interference from Information
limits are designed to provide reasonable protection against Technology Equipment (VCCI). If this is used near a radio or
harmful interference in a residential installation. This equipment television receiver in a domestic environment, it may cause radio
generates, uses, and can radiate radio frequency energy and, if interference. Install and use the equipment according to the
not installed and used in accordance with the instructions, may instruction manual.
cause harmful interference to radio communications. However,
we cannot guarantee that interference will not occur in a
particular installation. If this equipment causes harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, users are
encouraged to try to correct the interference by one or more of
these measures:
www.lumentum.com 14
Ordering Information
For more information on this or other products and their availability, please contact your local Lumentum account manager or
Lumentum directly at customer.service@lumentum.com.
North America
Toll Free: 844 810 LITE (5483)
China
Toll Free: 400 120 LITE (5483)