Beruflich Dokumente
Kultur Dokumente
1 Belt scale
zero and span weight Please recalibrated if scale
Daily/Weekly
be calibrated readings from your scale error
Check material build up in
mechanical installation
critical areas, such as under the Daily/Weekly
of the scale
weigh idlers
2 Bag Filter
3 CRUSHER unit
noise & vibration daily fixed or change
leaking oil or fluids daily fixed or change
4 General Conveyor
Walk Way Damage daily fixed or change
fixed or change
adjustment
Misalignment daily
cleaning
Cleaning daily
fixed or change or
Belt cleaner damage daily
adjustment
meke sure the fungtion ok
Switch / safety fungtion daily
before start conveyor
5 Metal Detector
6 Belt Scale
Ensure inside of panel keep
Panel and connection clean and dry, check to Weekly Clean control box
bolt ensure all wires, plugs, and
integrated circuits are tight in
Mechanical Coal
7
Sampler
8 Crusher unit
fixed or change
Side combs damage or wear weekly
fixed or change
segments crusher damage or loose bolts weekly
fixed or change
auto greasing reservoir and re-
pump unit weekly
fill
fixed or change
auto greasing & piping for leaks weekly
fixed or change
auto greasing unit distribution
weekly
block indikator pin
fixed or change
Spur Gear Chamber oil levels
weekly
and top up
9 General Conveyor
Belt belt tension 2 week add weight if needed
10 Metal Detector
Check sensitivity and belt clip
Control Setting Mountly Fixed/ recallibration
nullifier control seing
Passing some tramp metal Remove foreign object
Metal Detector Unit Mountly
through the detector from metal detector
11 Bag Filter
Check that the entire filter is
cleaned by means of acoustic 1 month/ 300 hour
control of the cleaning valves
Mechanical Coal
12
Sampler
Hub between hammer used,A torque wrench
tightening of screws mounthly
and main shaft
13 Vibrating Feeder
14 Vibrating Screen
vibrating screen Check the spring elements mounthly
Fixing screws for the shaft drive, 50 hour operation
spring elements and wear linings
15 General Conveyor
Tighten bolt/ change loose
Drive unit Tightening Bolt monthly
bolt
coupling oil level monthly add if needed
Tighten bolt/ change loose
bearing Tightening Bolt monthly
bolt
Pulley Lagging monthly change if lagging broken
movement roller and bracket change if lagging broken
Idler monthly
roller
Tighten bolt/ change loose
Bolt and nut Tightening Bolt monthly
bolt
16 Bag Filter
Any flexible connections must be
Bag Filter unit checked for wear 3month / 500 hour
and leakage
Mechanical Coal
17
Sampler
Refer to the gear
Lubrication Gear:
manufacturers
specification
The motor is equipped
motor
with sealed bearings
without
Amount lubricator nipples
of grease for first
Bearings: 3month
application: SNH511TG:
100 g of type TG.
18 Vibrating feeder
vibration stroke if change V-belt, please
Check of rubber spring 3mounth
increases/decreases see series in IOM
20 General Conveyor
Drive unit gear condition 6 mounthly fixed or change
coupling hub an other element 6 monthly fixed or change
21 Crusher unit
remove spur gear oil and replace 6 monthly/4000 re-change new oil
pump unit
per t 0138 hour
22 Bag Filter
-Check power
-Check fuse
-Check that the power
switch is on and that power
supplied to the unit
-Check unit connetion
-Check that all termination
Unit Trouble IF Necessary
are secure
-chect to ensure the display,
module, and keypad connectors
are firmly seated in their
connectors
-check that all jumpers are in
their correct position
23 Crusher unit
pump unit replace voith coupling oil 15000 hour re-change new oil
gear box crusher change gearbox oil and refill 1500 hour re-change new oil
with box
gear newinput
lubricant
shaftinseals 2000 hour fixed or change
gear box output shaft seals 6000 hour fixed or change
Crusher unit all bolts must be check for annual maintanance Tighten bolt/ change loose
thightness and re torqued to the bolt
24 General Conveyor
coupling Misalignment annual maintanance if coupling have
misalignment please re