Beruflich Dokumente
Kultur Dokumente
DHCP Sim
October 16th, 2016 Go to comments
You can download this lab and practice with Packet Tracer at
http://www.9tut.com/download/9tut.com_DHCP_Sim.zip (note: In this Packet Tracer file we use FastEthernet
instead of Ethernet connections; and interfaces Fa1/0, Fa1/1 instead of interfaces Et0/2, Et0/3)
Question 1
Examine the DHCP configuration between R2 and R3, R2 is configured as the DHCP server and R3 as the
client. What is the reason R3 is not receiving the IP address via DHCP?
Answer: A
http://www.9tut.com/dhcp-sim#more-2841 1/10
11/3/2017 CCNA Training DHCP Sim
Explanation
First we should check which interface on R3 that is connected to R2 via the show run command.
From the description we learn interface E0/1 is connected to R2. Use the show ip interface brief command to
verify the IP address of this interface.
Therefore we can conclude this interface does not have any IP address and there is no configuration on this
interface (except the description Link to R2 line).
If R3 wants to receive an IP address from R2 via DHCP, interface E0/1 should be configured with the command
ip address dhcp so the answer DHCP is not enabled on this interface is correct.
Question 2
R1 router clock is synchronized with ISP router. R2 is supposed to receive NTP updates from R1. But you
observe that R2 clock is not synchronized with R1. What is the reason R2 is not receiving NTP updates from
R1?
Answer: D
Explanation
First we should verify if the ports connected between R1 and R2 is in up/up state with the show ip interface
brief command on R1 & R2.
http://www.9tut.com/dhcp-sim#more-2841 2/10
11/3/2017 CCNA Training DHCP Sim
Note: We learn R1 & R2 connect to each other via E0/2 interface because the IP addresses of these interfaces
belong to 192.168.10.0/30 subnet. Both of them are up/up so the link connecting between R1 & R2 is good.
Next we need to verify the ntp configuration on R2 with the show running-config command.
So there is only one command related to NTP configuration on R2 so we need to check if the IP address of
192.168.100.1 is correct or not. But from the show ip interface brief command on R1 we dont see this IP ->
This IP address is not correct. It should be 192.168.10.1 (IP address of interface E0/2 of R1), not 192.168.100.1.
Question 3
Why applications that are installed on PCs in R2 LAN network 10.100.20.0/24 are unable to communicate with
Server1?
A. A standard ACL statement that is configured on R1 is blocking the traffic sourced from R2 LAN network.
B. A standard ACL statement that is configured on R1 is blocking the traffic sourced from Server1 network.
C. A standard ACL statement that is configured on R2 is blocking the traffic sourced from Server1 network.
D. A standard ACL statement that is configured on R2 is blocking the traffic sourced from R2 LAN network.
Answer: C
Explanation
http://www.9tut.com/dhcp-sim#more-2841 3/10
11/3/2017 CCNA Training DHCP Sim
The ping worked well so maybe R1 is good so we should check R2 first. We notice on R2 there is an access-list:
This access-list is applied to E0/2 interface with inbound direction. The purpose of this access-list is to block
traffic with source IP address of 172.16.200.0/24 so it will block all traffic sent from Server 1 to us.
Question 4
Users complain that they are unable to reach internet sites. You are troubleshooting internet connectivity
problem at main office. Which statement correctly identifies the problem on Router R1?
Answer: A
Explanation
If all users cannot access internet then R1 is most likely to cause the problem so we should check it first. From
the show running-config command we will see:
http://www.9tut.com/dhcp-sim#more-2841 4/10
11/3/2017 CCNA Training DHCP Sim
We notice that interface E0/0 (connected to ISP) has been configured as nat inside while interfaces E0/1 &
E0/2 (connected to our company) have been configured as nat outside. This is not correct because nat inside
should be configured with interfaces connected to our company while nat outside should be configured with
interfaces connected to the internet. Therefore we can conclude the NAT configuration on these interfaces is not
correct.
1. Dumps
September 11th, 2017
Hi everyone,
Please send me latest dumps for CCNA 200-125 on email: georgi_levski_1914 @ abv.bg
Thanks!
2. I have dumps
September 17th, 2017
3. Dumps
September 17th, 2017
Please sent me the latest dumps for CCNA 200-125 on email: {email not allowed}
4. Dumps
September 17th, 2017
5. Bilal
September 19th, 2017
Interface IDS are not listed correctly in this lab zip file
6. David
September 20th, 2017
7. kaleem
September 22nd, 2017
8. Mr X
September 26th, 2017
9. Anonymous
September 26th, 2017
I have the latest dumps if any one need please contact me .. bakhtkakar9@gmail-dot-com
11. inthemoment
September 29th, 2017
hello can someone please send me the latest 200-125 dumps to forthedroid at gmail dot com.
12. MS
October 2nd, 2017
passed my exam last week got 9xx this Sim was one of my questions, 80 percent of the questions from this
dumps. thanks 9tut
13. Radutir
October 8th, 2017
9tut, at q3, pls change Server0 with Server0 and vice-versa acording .zip topo, for new lerners.
14. Radutir
October 8th, 2017
15. moatasem
October 10th, 2017
http://www.9tut.com/dhcp-sim#more-2841 6/10
11/3/2017 CCNA Training DHCP Sim
moatasem82 at hotmail.com
16. Mik
October 13th, 2017
PLEASE!
17. Miki
October 13th, 2017
18. Machoy
October 16th, 2017
Hi everyone,
Please send me latest dumps for CCNA 200-125 on email: machoy1200-at-gmail-dot-com
Thanks!
19. zakrota
October 17th, 2017
20. Ben
October 21st, 2017
Hi Everyone,
In this example, do we still need to configure or correct the error in the lab exam? or you can just answer it
via multiple choice?
1 more month and Im gonna take the exam.
thanks in advance!! :)
21. H
October 22nd, 2017
22. Tyler
October 24th, 2017
@H what are your reviewing materials? Did you use chinese dump 10.10 and 100q himzo?
23. Ben
October 24th, 2017
http://www.9tut.com/dhcp-sim#more-2841 7/10
11/3/2017 CCNA Training DHCP Sim
@Tyler
Can you please send me the latest dumps? only have 9.18 dump. Please?
send latest dump please, exam on 4th; email at: unseenwoes@gmail dot com
25. LouGees
November 3rd, 2017
Comment pages
Previous 1 2 3 4 2841
Add a Comment
Name
Submit Comment
Subscribe to comments feed
RIPv2 Troubleshooting Sim TCP and UDP Tutorial
CCNA 200-125
CCNA Lab Sim
CCNA FAQs & Tips
Basic Questions
OSI TCP/IP Model Questions
Cloud & Virtual Services
WAN Questions
PPP Questions
QoS Questions
PPPoE Questions
MPLS Questions
DMVPN Questions
CDP & LLDP Questions
IP Address Questions
Switch Questions
Switch Questions 2
VLAN Questions
VLAN Questions 2
Trunking Questions
STP Questions
STP Questions 2
http://www.9tut.com/dhcp-sim#more-2841 8/10
11/3/2017 CCNA Training DHCP Sim
RSTP Questions
VTP Questions
Port Security Questions
SPAN Questions
EtherChannel Questions
InterVLAN Routing
Router Questions
Switch Stacking & Chassis Aggregation
Access list Questions
IP Routing
IP Routing 2
Subnetting Questions
RIP Questions
OSPF Questions
OSPF Questions 2
EIGRP Questions
BGP Questions
IP SLA Questions
NAT/PAT Questions
HSRP Questions
IPv6 Questions
IPv6 Questions 2
IPv6 Questions 3
Security Questions
Security Questions 2
Troubleshooting Questions
DHCP Questions
Syslog Questions
SNMP Questions
NTP Questions
SDN Solution
Wireless Questions
Miscellaneous Questions
Drag and Drop
Share your CCNA v3.0 Experience
CCNA Self-Study
Practice CCNA GNS3 Labs
CCNA Knowledge
CCNA Lab Challenges
Network Resources
Free Router Simulators
ICND1/ICND2 Website
CCIE Website
Top
http://www.9tut.com/dhcp-sim#more-2841 10/10