Beruflich Dokumente
Kultur Dokumente
Random access
4 RarAndPagingCR response message 117
and a paging
message code rate
channel
interference
PrachIntrfRejSwitch
suppression
function control
5 PrachIrcSwitch,PR OFF
ACH channel using
PrachIrcSwitch
MRC/IRC adaptive
function is enabled.
receiving RB occupied by
the reliability more bigger,
the message will, the more
random access response
messages or paging
messages lower than
Coverage and interference many, may be the system
MOD CELLDLSCHALGO:
problems led to success rate LocalCellId=x, throughput. The more
of paging is low, can improve parameters too big,
the paging power. RarAndPagingCR=117;
random access response
message and RB occupied
by the paging messages
will be less, but random
access response message
interference RACH access and
rise; aPRACH
paging channel
message
success rate of paging is low, receiving will reduce
interference suppression
can improve the paging power. function is enabled, you
MOD CELLALGOSWITCH:
Hardware restrictions:LBBPc can improve PRACH
LocalCellId=0, PrachIntrfRejSwitch
plate and uplink receiving adopts channel of false alarms,
= ON,
single antenna or antenna and RACH channel access
IrcSwitch= PrachIrcSwitch-1;
number is greater than 2:LBBPc success rate, success rate
baseband board does not of switching success rate,
support interference suppression heavy synchronization or
38-007-H113000132
ONET
35
False alarm
number is too high,
it can increase the
RACH threshold
detection
2 RachThdBoostRatio percentage
threshold.
improvement
Changed the
RachThdBoostRati
o to 50
PRACH IRC
3 PrachIrcSwitch OFF
algorithm switch
Random access
4 RarAndPagingCR response message 50
and a paging
message code rate
B56_MSG_SIZE_GRO
2 MessageSizeGroupA Judgment threshold Msg3 size
UPA;
38-007-H113000132
-62
B56_MSG_SIZE_GRO
UPA
MS1000_T300
15
This is a
No. The parameter name The description of recommended
the parameters.
Wait for the MME S1 interface value.
1 S1MessageWaitingTimer 20s
response message timer
a
No. The parameter name The description of recomme Configuration
the parameters. principles
the road, you can reduce the
nded hysteresis, switch to speed
1 IntraFreqHoA3TimeToTrig Intra-frequency handover 320ms up.
time delay Signal fluctuation is
considerably large section of
Within the system switchover the road, you can enlarge the
T304 switch inside the timer, Switching success rate is low.
2 T304ForEutran ms1000
indicating that the system within the system
timer T304 duration of use.
cell quality is higher the road, will be reduced
than that of the offset small threshold, to speed up
3 IntraFreqHoA3Offset values of the serving the switch.
cell. The value is more Signal fluctuation is
bigger, it indicates that considerably large section of
you needmeasures
switch to target cellA3
event the road, can increase the
time delay. Signal fast fading section of
When intra-frequency the road, you can reduce the
handover event meets hysteresis, switch to speed
4 IntraFreqHoA3Hyst trigger conditions cannot up.
be immediately reported, Signal fluctuation is
but when the event within considerably large section of
the time delay, always the road, you can enlarge the
meets the reporting hysteresis.
frequency
condition,measurement-
only then
based RSRP trigger threshold For inter-frequency handover
value of the event. When failure cause call drops more
5 InterFreqHOA4ThdRSRP
RSRP measurement result scenarios, may make increase
exceeds the threshold, will the threshold.
trigger the inter-frequency
MOD
INTERFREQHOGROUP:LocalCellI The load transfer 20M will reduce,20M load is
d=x,InterFreqHoGroupId=x,InterFre heavy traffic balance result is affected.
qHoA4ThdRSRP=1dB;
a
No. The parameter The description of the recommen
name parameters. ded
Configuration principles
When configuration adaptive strategy,
MML command
if the RB required by the user number
is less than 1 a RBG, according to the
actual number of RB need scheduling;
If the RB required by the user number
greater than 1 a RBG and does not MOD CELLDLSCHALGO: LocalCellId=x,
equal to the RBG integer times, namely RbgAllocStrategy=ADAPTIVE;
between N between a RBG and (N+1) RBG,
the current TTI assign (N+1) a RBG.
Compared with the RBG roundup of
strategy RbgAllocStrategy=ROUND_UP,
You can save PRB resources.
In high load scenario, general air interface MOD RLCPDCPPARAGROUP:
quality will have different degree of DiscardTimer=DiscardTimer_Infinity
deterioration, bit error rate will have Pay attention to the parameter reference
different degree of deterioration, relationship, set in the
accompanied by air interface RLCPDCPPARAGROUP DiscardTimer
retransmission rate will increase, which value; Referenced in the STANDARDQCI
results in PRB is wasted. RLCPDCPPARAGROUP accordingly.
command by the base station status
report, but directly to the target access.
initiated by In this case, the base station of
MOD ENODEBALGOSWITCH:
the source side will repeatedly retransmit
HighLoadNetOptSwitch=SPECSIGRETR
the status report, leading to unnecessary
ANSOPTSWITCH-1;
overhead. air interface resources This
optimization items to open after the inter-
system handover command of RLC
MOD
It is recommended that only in large- CELLALGOSWITCH: LocalCellId=x,
traffic scenarios. CellSchStrategySwitch=AbnUeSchSwitch
-1;
Traffic equilibrium
RBG resource
1 RbgAllocStrategy ADAPTIVE
allocation strategy
PUSCH DTX
3 UlSchSwitch Turn it off.
detection
UlEnhancedSrSch Optimization of SR
4 Turn it off.
Switch rescheduling
MLB based on UE
7 Feature
UL Traffic
indicates that
trigger the inter-
frequency load-
balancing
8 MlbMinUeNumThd algorithm uplink
synchronization
state minimum
judgment threshold
of the number of
indicates the ratio of
cell spectral
9 RsvdPara51 efficiency in the local
cell to that in a
neighboring cell.
Configuration principles
When configuration adaptive strategy, if
MML command
the RB required by the user number is
less than 1 a RBG, according to the
actual number of RB need scheduling; If
the RB required by the user number MOD CELLDLSCHALGO:
greater than 1 a RBG and does not equal LocalCellId=x,
to the RBG integer times, namely between
N between a RBG and (N+1) RBG, the RbgAllocStrategy=ADAPTIVE;
current TTI assign (N+1) a RBG.
Compared with the RBG roundup of
strategy RbgAllocStrategy=ROUND_UP,
You can save PRB resources.
MOD SRSCFG:
LocalCellId=0,
Number of subscribers in heavy traffic, SrsCfgInd=BOOLEAN_TRUE,
cell than many scenarios.
FddSrsCfgMode=ADAPTIVEM
ODE;
MOD CELLALGOSWITCH:
UE the omission DCI0 or DRX state have SR LocalCellId=0,
false alarm UlSchSwitch=PuschDtxSwitch
-1;
MOD
CELLALGOSWITCH:UlSchSw
Open the scenario DRX
itch=UlEnhancedSrSchSwitch-
1;
MOD CELLULSCHALGO:
Low coding efficiency: it is generally believed
LocalCellId=x,
that PUSCH MCS < 10, just think the coding
UlRbAllocationStrategy=FS_I
efficiency is very low.
NRANDOM_ADAPTIVE;
Traffic equilibrium
Traffic equilibrium
Solution
No. Brief introduction Optimization method
properties
Mod ENBRSVDPARA:
Open the adaptive cycle CQI RsvdSwPara0=RsvdSwPara0_bit9-1;
reported by optimizing (eRAN6.1 version is changed to visible
2 characteristics Feature parameters:
(LBFD-002025 Basic Mod CQIADAPTIVECFG:
Scheduling) PucchPeriodicCqiOptSwitch=ON;)
//IR
Uplink interference Mod CELLULSCHALGO: LocalCellId=0,
randomization + line frequency UlRbAllocationStrategy=FS_INRANDOM_A
choose enhanced DAPTIVE;
3 Feature
(LBFD-002025 Basic
Scheduling) //UL EFSS
To be implemented. Mod CELLALGOSWITCH: LocalCellId=0,
UlSchSwitch=UlEnhancedFssSwitch-1;
Open the PUSCH DTX detection Mod CELLALGOSWITCH: LocalCellId=0,
4 (LBFD-002025 Basic Feature UlSchSwitch=PuschDtxSwitch-1;
Scheduling)
11/10/2017 , 3345
371265785.xlsx
11/10/2017 , 3445
371265785.xlsx
The Optimize
baseline Applicability the role.
value.
The
uplink
1.LBBPd plate, and the configuration DeltaShift=DS1_DELTA_SHIFT scenario is
OFF throughp
recommended. ut is
improved.
The
uplink
OFF ALL throughp
ut is
improved.
The
Before version, only LBBPd 1.eRAN6.0 SPC260/280 board support,LBBPc board is uplink
OFF expected in eRAN6.0 SPC260/280 version supports. throughp
In particular, 2 in SR false alarm serious scenario, can open the DTX mitigation. ut is
1 macro stations:eRAN3.0 and eRAN6.0 SPC190 before version, only LBBPd board improved.
support,eRAN6.0 SPC200 and later versions LBBPc board also supports;
2 small station:V100R005C00SPC210 SRS, and later versions support closed The
before version does not support; uplink
OFF 3 after closing the SRS open-closed loop MIMO adaptive can be used. throughp
4, heavy traffic scenarios (single-cell at the same time the number of online ut is
users in busy hour above 200, use L.Traffic.User.Max collected over) are not improved.
advised to disable SRS (SRS flower arrangement does not affect the
configuration);
The
1 before eRAN6.0 SPC280 version, non-Ran Sharing scenario. uplink
OFF 2 in eRAN6.0 SPC280 and later solve Ran Sharing match problem, remove the throughp
limit. ut is
improved.
11/10/2017 , 3545
371265785.xlsx
1.SRS which are closed and for low-speed user-based network (Highest Speed
Supported<110km/h). The
2 TA Timer proposal is stretched to 5120ms, such as 1920ms 5120ms instead. uplink
SF1920 3 will bind DRX long-period of configuration, and DRX cooperation: measured throughp
with DMRS timing when, in order to meet the needs of the uplink timing, TA ut is
placing cycle must be met, and there are at least once within DRX in active stage, improved.
do as follows to DRX long-period constraint:LongDRXCycle<=TA placing cycle.
11/10/2017 , 3645
371265785.xlsx
11/10/2017 , 3745
371265785.xlsx
11/10/2017 , 3845
371265785.xlsx
Solution
No. Brief introduction propertie
s
The number of open PDCCH symbol 1 ~ 3 adaptive Paramete
1 (LBFD-002003 Physical Channel Management) r
Paramete
5 Open the closed-loop MIMO r
Paramete
6 Optimization of SCH power r
Paramete
7 Downlink IBLER target initial value r
Paramete
8 DL SSFN timer r
11/10/2017 , 3945
371265785.xlsx
The
Optimization method baseline
value.
Mod CELLPDCCHALGO: LocalCellId=0,
InitPdcchSymNum=1, PdcchSymNumSwitch=ON; OFF
//ECFI
Mod CELLPDCCHALGO: LocalCellId=0,
PdcchSymNumSwitch =ECfiAdaptionON;
OFF
//DL FSS
Mod CELLALGOSWITCH: LocalCellId=0,
DlSchSwitch=FreqSelSwitch-1;
MOD MIMOADAPTIVEPARACFG:
MimoAdaptiveSwitch=CL_ADAPTIVE;
MOD CELLCQIADJALGO:InitDlIblerTarget=12
MOD CELLULSCHALGO
11/10/2017 , 4045
371265785.xlsx
Optimize
Applicability the role.
Downlink
throughp
All ut is
improved.
Downlink
1 non-high-speed rail FDD mode scenarios, it is recommended throughp
that the value is ECfiAdaptionON. ut is
improved.
11/10/2017 , 4145
371265785.xlsx
11/10/2017 , 4245
371265785.xlsx
This is a
No. The parameter name The description of the
This parameter indicates that cell recommended
parameters.
PRACH configuration index is value.
configured. When the RACH resource
1 PrachConfigIndexCfgInd adjustment algorithm switch and CFG
PRACH configuration index indicating
open at the same time, priority PRACH
The
indexparameter and instructions.
configuration their corresponding
PRACH cycle more bigger,eNodeB
support access load uplink resources
occupied by the lower, less; The
2 PrachConfigIndex 6 (5ms)
smaller the parameter and their
corresponding PRACH cycle,eNodeB
support access load more bigger, the
more uplink resources are occupied.
11/10/2017 , 4345
371265785.xlsx
11/10/2017 , 4445
371265785.xlsx
The performance
impact.
11/10/2017 , 4545