Beruflich Dokumente
Kultur Dokumente
1 thru 10
Features
Specifically designed for slurry service.
No metal parts in contact with the
flowing slurry.
Molded elastomer sleeve, no fabric.
Inherent abrasion resistance of sleeve
provides both high performance and
long life.
The C-Valve closes in compression,
not tension, creating less stress on
the sleeve, therefore the sleeve is not
subject to tear propagation resulting
from solid particles passing through
the valve at high velocity.
Rubber muscle constricts a full
360-degrees around the sleeve
maintaining a perfectly round and
concentric aperture across the full
throttling range.
Round orifice provides high capacity,
straight through, unobstructed slurry
flow.
Modified linear characteristic make
the valve compatible with most
automatic control requirements.
Throttling range from wide open to
50% reduction in diameter, or 75%
reduction in orifice open area, up to
a 90% reduction of maximum flow.
Field-replaceable, elastomer wear Shown with optional actuator and
parts are standard. control accessories
Flow Control
Total Flow Control Solutions Tyco reserves the right to change product designs and specifications CLKMC-0109-US-0307
without notice. Copyright 2003 by Tyco International Ltd.
Clarkson C-Valve Slurry Throttling Valve
1 thru 10
Features
The design of the C-Valve takes into account
the many culprits in slurry systems that cause
problems for other types of valves including
abrasion, cavitation, corrosion, sanding,
scaling, and temperature. It is rugged and
abrasion-resistant with good control
characteristics. It features a straight-through
flow path with no metal parts in direct contact
with the slurry.
The C-Valve consists of an elastomer sleeve,
available in various materials, surrounded by
an elastomer muscle, inside a cast ductile
iron body housing. To throttle the slurry flow,
the muscle is compressed inward by hydraulic
pressure, reducing the orifice size of the
sleeve in a 360-degree squeeze. As it
constricts, a round and concentric aperture is
maintained across the entire throttling range,
from wide open to 50% reduction in diameter.
Elastomer
This equates to a 75% reduction in open area
sleeve
or up to 90% reduction of maximum flow. Its
closure pattern provides modified linear
control.
Various sleeves available to suit Sleeve retainer
application in size and media
The standard C-Valve sleeve orifice is full port
in the wide-open condition; however, many Elastomer muscle Ductile iron body housing
times a reduced port is better suited to the Face drilled and tapped to ANSI B16.5/150
application. Optional reduced-port sleeves are
available to change the size of the orifice.
Available Sleeve Sizes
They are inexpensive, easily installed and give
the user the flexibility of varying the valve size Valve Size 1 1.50 2 3 4 6 8
to meet changing conditions. Additionally, in Full Port 1x1 1.5 x 1.5 2x2 3x3 4x4 6x6 8x8
applications where the exact process
Reduced Port 1 x .75 1.5 x 1 2 x 1.50 3 x 2.5 4x3 6x5 8x7
conditions are not initially known, a smaller
1 x .50 2x1 3x2 4x2 6x4 8x6
bore reducing sleeve valve can be installed to
correct inadvertent oversizing. 1 x .38 3 x 1.50 6x3 8x4
1 x .25
The standard sleeve is made from gum 1 x .19
rubber, the best all-around elastomer.
It combines superior physical properties with a
wide range of chemical compatibility.
Other available elastomers include:
Chlorobutyl: A high temperature elastomer
having good physical properties for services
up to 260F.
EPDM: High temperature applications up to
250F.
Neoprene: Compatible with many oils and
solvents at temperatures up to 200F. Modest
abrasion resistance limits its use and poor
permanent set qualities.
Viton, Nitrile, Hypalon and Urethane are
also available on an application basis.
Note
Contact the factory for assistance in sizing
and proper application of the available Viton is a registered trademark of DuPont Dow Elastomers.
elastomers.
Tyco reserves the right to change product designs and specifications CLKMC-0109
without notice. Copyright 2003 by Tyco International Ltd. 2
Clarkson C-Valve Slurry Throttling Valve
1 thru 10
Throttling position
Valve Sizes
Valve Size 1 1.5 2 3 4 6 8
A 5.38 6.13 7.81 10.44 12.81 18.5 28
B 6 7.63 9.25 13 14.5 19 24.88
C 4.25 5 6 7.5 9 11 13.5
BC 3.12 3.88 4.75 6 7.5 9.5 11.75
nxd 4x 1/2-13 4x 1/2-13 4x 5/8-11 4x 5/8-11 8x 5/8-11 8x 3/4-10 8 x 3/4-10
nxd
Tyco reserves the right to change product designs and specifications CLKMC-0109
without notice. Copyright 2003 by Tyco International Ltd. 3
Clarkson Series C-Valve Actuator
for 1, 1-1/2 and 2 Slurry Control Valves
Tyco reserves the right to change product designs and specifications CLKMC-0109
without notice. Copyright 2003 by Tyco International Ltd. 4