Sie sind auf Seite 1von 2

www.jntuworld.com www.android.jntuworld.com www.jwjobs.

net

Code: 9D54104

M.Tech - I Semester Regular & Supplementary Examinations, April/May 2013


ANALYSIS OF POWER ELECTRONIC CONVERTERS
(Common to PE & ED, PE , PED and PID)
Time: 3 hours Max Marks: 60
Answer any FIVE questions
All questions carry equal marks
*****
1 (a) Explain in detail the operation of 1- half wave ac voltage controller with R-L load
with the help of necessary waveforms and circuit diagram.
(b) A 1- ac voltage controller has a resistive load of R = 10 and the input voltage

D
is The delay angle of thyristor is Determine
(i) The RMS value of output voltage.

2 (a)
(ii) The input power factor.
(iii) The average input current.

R L
Analyze the 3- bidirectional - connected controller circuit with resistive load.
(b)

O
The 3- bidirectional - connected controller has a resistive load of R = 10
The line to line voltage is = 208 V(rms), 60 Hz. The delay angle is 2
.

Determine

W
(i) The expressions for instantaneous currents ia, iab, ica.

U
(ii) The RMS output phase current.

T
(iii) The RMS line current.
(iv) The RMS current of thyristor.

3 (a)

(b)
J N
Describe the power circuit of 3- to 3- cyclo converter (mid - point configuration)
and also explain its operation with resistive load.
Discuss the advantages and applications of cyclo converters.

4 (a) A 1- bridge type cyclo converter has input voltage of 230 V, 50 Hz and load of R
= 10 , output frequency is one -third of input frequency. For a firing angle delay
of 30 degrees, calculate:
(i) RMS value of output voltage.
(ii) RMS current of each converter.
(iii) Input power factor.
(b) Describe the power circuit of 1- dual converter and explain its operation for R-L
load.
Contd. in Page 2

Page 1 of 2

www.jntuworld.com
www.jntuworld.com www.android.jntuworld.com www.jwjobs.net

Code: 9D54104

5 (a) Explain the operation of 3- to 3- half controlled cyclo converter (bridge


configuration) with R-L load for continuous conduction mode.
(b) Explain the procedure for evaluation of input power factor and harmonic factor in 3-
cyclo converter.

6 (a) Analyze step down DC-DC converter circuit with R-L load.
(b) A step down DC-DC converter feeding an R-L load with mH
k = 0.5 and E = 0 V, calculate:
(i) The peak instantaneous load current.
(ii) The average value of load current.
(iii) The RMS chopper current.

7 (a)
(iv) The effective input resistance seen by source.

L D
What is the significance of performance parameters in practical inverters? List out
various performance parameters and explain.
(b)

R
The single-phase half bridge inverter (employing transistors) with resistive load of
R = 2.4 and dc input voltage is = 48 V. Determine:

O
(i) The RMS output voltage at the fundamental frequency.
(ii) The output power.

W
(iii) The average and peak currents of each transistor.
(iv) The peak reverse blocking voltage of each transistor.

U
(v) The total harmonic distortion.

8
(a)
(b) T
In 3- bridge inverters, explain:
Sinusoidal PWM method of voltage control.

N
Space vector modulation method of voltage control.

J *****

Page 2 of 2

www.jntuworld.com

Das könnte Ihnen auch gefallen