Beruflich Dokumente
Kultur Dokumente
v. Provision of 4mm PVDF Roof Cladding with complete hardware and accessories.
vi. Provision of 6mm solid colored polycarbonate sheet on steel tubular frame roof ventilator
at service area, main entrance and entrance canopy with complete hardware and accessories.
vii. Provision and application of Elastomeric Water Proofing and Polythelene vapor barrier
sheet.
I. DOORS AND WINDOWS
i. Provision and installation of Doors and Windows with complete hardware and accessories
(see plan for details).
J. FINISHES
i. Provision and installation of Ceiling using 600mm x 600mm semi-recessed acoustic board
including tee runner, hangers, supports and hardware.
ii. Installation of 3.0mm fiber cement board in light steel framing system.
iii. Provision of 150x3600mm pre-painted G.I. Strip and 125x3000mm PVC Panel.
K. SPECIAL CONSTRUCTION (ATRIUM)
i. Provision of Glass Frames and complete accessories for Atrium Block.
ii. Application of Dirt Resistive exterior latex paint finishes (exterior).
L. TILE WORKS
i. Provision of 600mm x 1200mm, 600mm x 1800mm and 600mm x 2400mm Polished
Granite Slab for Concrete Counter.
ii. Provision of 200mm x 200mm, 300mm x 300mm (Glazed and Unglazed) Ceramic Tiles
and 600mm x 600mm Granite Tiles and 600mm x 600mm Granite Stone (see Floor Finish
Legend).
iii. Provision and Installation of 600mm x 600mm Granite Stone on Exterior Floor (Main
Step Entry and Main Entry Porch).
iv. Provision and Installation of 200mm x 200mm Button Tile on Exterior Floor (Staff Entry
Ramp and Entry Porch, Service Ramp and Steps, Rear Exit Ramps and Stairs).
v. Provision and Installation of Compact Roll and Anti-Bacterial Roll Vinyl Continuous Floor
Finish with cove and grove at ends as indicated in the drawing. Use Rugby Contact Cement.
vi. Provision of Laminate Sheets on 10mm Wood Backing, 4 Resilient Vinyl Baseboard and
150mm Wood Baseboard and other accessories as indicated in the drawings.
vii. Provision of Brass Nosing and Lining.
viii. Application of Tile Grout.
ix. Cleaning and removing of Excess cement.
M. ELECTRICAL WORKS
i. Interior Rough-ins: Laying of Electrical Wires, Pipes & fittings
ii. Provision & Installation of Electrical Fixtures and Accessories: Panel Board with Circuit
Breakers, Switches, Convenience Outlets, Lighting Fixtures and other accessories as
indicated in the drawings.
iii. Provision and installation of Auxiliary Devices ( Smoke Detector, Heat Detector,
Annunciator 9 Zones, Fire Alarm Bell, Fire Alarm Manual Station (push-button), Paging
Equipment Amplifier System, Paging Speakers, PABX System Equipment see plan for
details).
iv. Provision and installation of Electrical Equipment (Lightning Air Terminals with complete
assembly and accessories.
v. Provision of 333KVA Transformer, Single Phase, Double Bushing, Primary Voltage
240/480Volts, 60HZ Oil Emerge.
N. PAINTING WORKS
i. Removal of Excess Concrete, Smudges and Clean areas to receive paint
ii. Application of Concrete Neutralizer.
iii. Application of Primer Coats for Concrete, Wood and Steels.
iv. Application of Acrytex Cast, Body Filler and Patching Compound.
v. Application of Putty.
Contract Name & Location: ITB No. 2017-18 (1) CONSTRUCTION OF REGIONAL BLOOD CENTER
BUILDING, BRGY. CABALAWAN, TACLOBAN CITY.
-------------------------------------------------------------------------------------------------------------------------------
----------
3. Specimen Preparation (Top and Bottom Cabinet): Provision and Fabrication of thick
Marine Plywood with 0.70mm thick Laminates on Contact Cement as Adhesive (back to
back), on x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging, 2x3 S4S KDVT
Wood as Cabinet Frame with Automotive Lacquer Finish (2 coats) and other accessories
(cabinet / drawer handle, hinge, drawer slide, etc.)
iii. Blood Sample Reception (Bottom Cabinet): Provision and Fabrication of thick
Marine Plywood with 0.70mm thick Laminates on Contact Cement as Adhesive (back to
back), on x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging, 2x3 S4S KDVT
Wood as Cabinet Frame with Automotive Lacquer Finish (2 coats) and other accessories
(cabinet / drawer handle, hinge, drawer slide, etc.)
iv. Hemoglobin Test (Top and Bottom Cabinet): Provision and Fabrication of thick
Marine Plywood on x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging, 2x3
S4S KDVT Wood as Cabinet Frame with Automotive Lacquer Finish (2 coats) and other
accessories (cabinet / drawer handle, hinge, drawer slide, etc.)
v. Hand Washing 2nd (Bottom Cabinet): Provision and Fabrication of thick Marine
Plywood on x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging, 2x3 S4S
KDVT Wood as Cabinet Frame with Automotive Lacquer Finish (2 coats) and other
accessories (cabinet / drawer handle, hinge, drawer slide, etc.)
vi. Directors Pantry 2nd (Top and Bottom Cabinet): Provision and Fabrication of thick
Marine Plywood on x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging, 2x3
S4S KDVT Wood as Cabinet Frame with Automotive Lacquer Finish (2 coats) and other
accessories (cabinet / drawer handle, hinge, drawer slide, etc.)
vii. Collection Staff Base 1 (Bottom Cabinet): Provision and Fabrication of thick Marine
Plywood with 0.70mm thick Laminates on Contact Cement as Adhesive (back to back), on
x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging, 2x3 S4S KDVT Wood as
Cabinet Frame with Automotive
Lacquer Finish (2 coats) and other accessories (cabinet / drawer handle, hinge, drawer slide,
etc.)
viii. Collection Staff Base 2 (Top and Bottom Cabinet): Provision and Fabrication of
thick Marine Plywood on x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging,
2x3 S4S KDVT Wood as Cabinet Frame with Automotive Lacquer Finish (2 coats) and
other accessories (cabinet / drawer handle, hinge, drawer slide, etc.)
ix. Screening Post Donation (Bottom Cabinet): Provision and Fabrication of thick
Marine Plywood with 0.70mm thick Laminates on Contact Cement as Adhesive (back to
back), on x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging, 2x3 S4S KDVT
Wood as Cabinet Frame with Automotive Lacquer Finish (2 coats) and other accessories
(cabinet / drawer handle, hinge, drawer slide, etc.)
x. Donor Lounge Counter (Bottom Cabinet): Provision and Fabrication of thick Marine
Plywood with 0.70mm thick Laminates on Contact Cement as Adhesive (back to back), on
x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging, 2x3 S4S KDVT Wood as
Cabinet Frame with Automotive Lacquer Finish (2 coats) and other accessories (cabinet /
drawer handle, hinge, drawer slide, etc.)
xi. Information Recep. Registration (Bottom Cabinet): Provision and Fabrication of
thick Marine Plywood with 0.70mm thick Laminates on Contact Cement as Adhesive (back
to back), on x1 S4S Kiln Dried Vacuum Treated as Cabinet Door Edging, 2x3 S4S
KDVT Wood as Cabinet Frame with Automotive Lacquer Finish (2 coats) and other
accessories (cabinet / drawer handle, hinge, drawer slide, etc.
Submitted by: