Beruflich Dokumente
Kultur Dokumente
Computer Engineering
Sriwijaya University
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
- Students know the concept of data communication using bridging mode access.
- Students know differences bridging mode access.
- Students know how to set up the configuration bridging access mode.
Introduction
WiMAX Purpose
Software Configuration
1. Connect console cable from serial com on laptop to console port in BS IDUSet BS
IDU parameter for the first time are using console serial cable. This console serial
cable can be made by crossover connectivity from serial laptop to serial port on BS
IDU with Pinout reference that shown in this table :
1
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
Make sure serial port setting on laptop is same with these parameters :
If console cable connections is OK, login and password request will appear. Input
Login : admin and Password : admin, then prompt will pop out :
+ AN100U#>
2
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
6. Connect UTP straight cable from laptop LAN port to Management port in BS IDU
IP Address : 192.168.101.110
Additional Explananation :
- IP 192.168.101.3 is default management IP address.
3
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
1. Connect straight UTP cable from LAN port in laptop to Data port in PoE. Connect
the cable until the LED in PoE showing OK indicator.
2. Setting IP in laptop with this configuration:
IP Address : 192.168.101.110
Subnet Mask : 255.255.255.0
3. Make sure the laptop connection to BS IDU is connected by Pinging test to IP
Address 192.168.101.1 using Command Prompt. Good connection is showed by
good PING result.
4. Access to SU-O using Telnet 192.168.101.1 via Command Prompt, then Login
request will appear. Input admin on both Login and Password.
4
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
Keterangan :
If LoRfFreq1 and HiRfFreq1 have been set up in another channel, to change channel
with another new channel, use this command:
1 SUO(set ->)#>rfConfig LoRfFreq1 0
2 SUO(set ->)#>rfConfig HiRfFreq1 0
6. phyConfig CyclicPrefix must be same with Guard Interval that has been set up in
BS IDU :
1 SUO#>
2 SUO#> set
3 SUO(set ->)#>phyConfig CyclicPrefix 4
5
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
Additional Note :
- Make sure Link Status : Registered (1)
- Registered (1) indicator is showing SU-O are connected and accessible to BS-IDU
11. Do Monitoring to radio SU-O link status performance with this command :
1 SUO#>
2 SUO#>show status
6
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
7
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
Objectives
- Students know how to create Service Class.
- Students know what are the functions of Service Class.
- Students know what parameters of Service Class aim for.
Introduction
Service class is mechanism that used to handle data packet which can be found in MAC
WiMAX for data transfer usage. These Service Class are functionate for filling QoS
requirement for applications that been used in WiMAX network. Service Class are
located in Base Station and divided into downlink and uplink.
Software Configuration
Username : admin
Password : admin
8
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
9
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
10
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
[X] = 2 254
2. Login to Subscriber Station using Telnet and access to 192.168.101.1
11
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
12
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
Objectives
- Students know how to configure VoIP Server using Asterisk
- Students know how to configure VoiP Clients using softphone
- Students know about VoIP System
Introduction
VoIP is communication technology based on Internet Protocol (IP). VoIP can be used
in both internet and intranet. VoIP has advantages like low cost communication
because VoIP is able to be used in intranet network.
VoIP Purpose
- As a telecommunication media
- Low cost communication
- Give better voice quality
type=friend
context=[VoIP]
username=[100]
secret=[100]
host=dynamic
nat=no
dtmfmode=auto
disallow=all
allow=ulaw
allow=alaw
allow=gsm
13
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
There are some softphone that can be used such as Zoiper, Ekiga, X-Lite and etc.
Here we use Zoiper as the softphone. Most of these softphones have same
configuration.
14
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
6. Try to call another VoIP client to make sure that account creation was successfully.
15
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
VoIP has QoS parameters that are used as a measure to determine the quality of the
service. There are three parameters that affect the quality of VoIP, those are delay, jitter
and packet loss. Delay is the time it takes a data packet to reach its destination. Packet
loss occurs when data transmission is in progress. To know the value of these
parameters, can be used Wireshark to know and analyaze its value.
Analyzing Purpose
16
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
6. Change VoIP Server IP Address to 10.1.1.2 (if you use Virtual Machine, you have to
change the IP Address, but if not, you can skip this step) by running this command:
sudo gedit /etc/network/interfaces
17
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
1. Open Wireshark app and choose Network Adapter then click Start
18
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
3. Click Telephony menu and highlight RTP submenu and click RTP Streams
19
Computer Network Laboratory
Faculty of Computer Science
Sriwijaya University
To get Delay value, we need two parameters, Duration and Sent Data Packet. Based on
data we got, we have these information :
To get Packet Loss Percentage, we need two parameters, Sent Data Packets and
Received Data Packets. Based on data we got, we have these information :
20