Beruflich Dokumente
Kultur Dokumente
INPUT DATA
Loadings
Bending moment xx - M x := 50 kN m
Bending moment yy - M y := 5 kN m
Axial force - F := 62 kN
Shear force - S := 20 kN
Flange Thick. - T := 30 mm
Area of section = A := [ ( 2 b T) + [ ( d 2 T) t ] ]
d 2 T
Torsional area = AT := b T + t
3
b3 3
Moments of Inertia - Iy := 2 T + ( d 2 T) t
12 12
T3 d T ( d 2 T)
2 3
Ix := 2 b + b T + t
12 2 2 12
3 3
b d 2 T t
IyT := T +
12 3 12
Iy Ix
Section modulii - zy := 2 rx :=
b A
Iy Ix IyT
Radii of gyration - ry := zx := 2 rT :=
A d AT
TORSION RESISTANCE 3
2 b
( Taken from Roark Warping constant = Cw := ( d T) T
P367-table 21-case6) 24
K G
:=
Cw E
1
Tors 1
Angles of rotation - 1 :=
2 Ly
2 Cw E cosh
4
Tors y L
11 := tanh
2 Cw E 1
Tors
111 :=
2 C w E
ACTUAL STRESSES
Mx
Major axis bending = fbx := fbx = 9 mPa
zx
My
Minor axis bending = fby := fby = 6 mPa
zy
F
Tensile stress = fa := fa = 2 mPa
A
S
Shear stress = fq :=
d t fq = 2 mPa
Torsional stress - 1 := T G 1
2
( d T) b
2 := E 111
16
d T b E 11
x := 4
:= 1 + 2 + x = 20 mPa
ALLOWABLE STRESSES
TENSILE STRESS
Section D1; the allowable tensile stress of
members is detailed herein:- Ft := 0.6 Fy Ft = 213 mPa
SHEAR STRESS
Section F4; the allowable shear stress - Fq := 0.4 Fy Fq = 142 mPa
BENDING STRESSES
Section F; for members bent about their strong or weak axes, members with compact or non-compact sections as defined in Sect
B5, the allowable bending stress is defined in F1 and F2
Fb1 := 0.66 Fy
Ly
2
Fyimp 170000 Cb
2 rT F
Fb3 := mPa
2
Fb2 := y Ly
3 1530000 Cb r
T
Ly 510000 C b
Fbx := if > , Fb3 , Fb2
rT Fyimp
( )
Fb4 := if ( Fb4 > 0.6 Fy , 0.6 Fy , Fb4)
COMBINED STRESS
Section H2; for members subject to both axial tension fa fbx fby
and bending, the following equations shall equal less + + = 0.07
Ft Fbx Fby
than 1.0
fa fbx fby
if + + < 1.0 , "Beam OK" , "Beam Not OK" = "Beam OK"
Equivalent Stress
Ft Fbx Fby
This stress check is not required by AISC, but is commonly
performed. It is a requirement of other standards, for example
BS449 which requires a limit of 0.92 x SMYS
fe
fe := (fa + fbx + fby)2 + 3 ( fq + )2 = 0.13
0.92 Fy
fe
if < 1.0 , "Beam OK" , "Beam Not OK" = "Beam OK"
0.92 Fy
End of Section