6p—sleio, yy 35 =
Report of Calibration —_gccamms
‘Seg The Sana
Report No, 12201029
Rem Submitted Vernier Caliper
Mitutoyo Model 8" (0-200 mm)
Serial Number; 6339622
Submitted By Mohammad Al Moll Group
Dammam , Saudi Arabia
Date of Calibration 11 February 2013 ue Date 11 February 2014
Ambient wc 23° Relative Humidty: < 50%
Guif Equipment Metrology Service (GEMS) certifies thatthe above sted instrument has been calbrated
In accordance with a qualty system registered to [S0 $001:2008 an conform to ISOVIEC 17025;200 and
[ANSI/NCSL 2540.1-1994 using GEMS applicable procedures.
Measurement uncertainties if reported are calculated at 2 95% confidence level witha coverage factor
equal to two (k=2). I the measurement uncertainty is not reported atest uncertainty ratio (TUR) of 4:1
‘and k=2 was used,
‘cu Equipment Metrology Serace (GEMS) measurement standards ae traceable thru unbroken chain of
comparison tothe United Stats’ National Institute of Standard and Technology (NIST) andjor to CIPM
MRA signatory National Meology Institutes, orto natura physical constants, consensus standard rato
‘ype measurements.
This calibration reprt contains the results of calbrtion andor ater relevant data about the calration.
“Ths report apples only to the tem ilentied above and shall nat be reproduced except in ul without
specie written aporoval by GEMS.
Calibration Procedures: GEM-P-20-002,
‘As Received Conditions : In Tolerance
‘As Shipped Conditions : In Tolerance
Calibrated By: Approved By:
—— Ss
Calibration Tech. (stamp) S. Esquer (date)
Laboratory Ma
es Fon rac . Page 1 of 3
‘Gut Equipment Metrology Service (GEMS) Tome oan ona Ro
Poor iter bat auton 368 Tevinbanieatniee ee
Tarot es V587 50 syetentar ae
No sossoeuor Member he Natal Conference of Stns Laoraties centric gan aheGEMS
Verrier Caliper Report No. 12201029
ittoyo Mec 8 (0-200 mm) 11 Febeusry 2073,
Serial Number 6399622 Page 2013,
LL Test Method:
“The Unit Under Test (herein refered to 2s tho UUT), was castrated by applying, measuring and comparing
Is indcatons wih GEMS's stancards. Resul of the calbation s given below
Function Tested Nominal Measured ‘Tolerances
‘Values Values.
32 Preliminary Inspection
ae Oot meay : exc)
323 SnodhOpoaon ES au)
326 en Panle aU)
44 Outside Dimension Seale
tien) (et) ton)
412 Ur vanerzo0 ° 3 aes “a8
42 Outside Dimension Scale indication Test
Eran see (en) Aety (ety
42g “UU See ntton % % cana “to ssi28
aap : : wrasse
4 4 3137/28 448
7 a 3 3 Tiai2s te BAN
ves om (oe (ram
(OT Se eon i270 1270 wes ta 1278
pogo 2540 2540 25352548
a ‘0160 0160 fos f018s
° a 20329 20520 2315 te 20025,
43 Inside Dimension Scale Indization Test
Erte oa (neh) (hen toon)
a5 "Use aenon i verns “to” tae
5 ts 8 a rian bane
tse Sale (rm) (om (rm
GT Se enon 2540 2540 2sas “25.45
a 20320 20320 2001820325
44 Depth Gauge Indication Test
emis see (en) (ety (ie
UOT See nseaton % % eanze “to” ps8
a ; t wn te T28
; ‘ 4 aizmize te 428
a 8 Tranes te BAmN28
swe seo8 (om) (om (om
40 NlUrSeo oan S270 i270 wes “a! 1275
a eee 2540 25.40 2382548
orn 0160 woiss fates
2320 203.20 20018 205.25,
Caitation TeebricianGEMS
Verier Caliper FReport No. 12201028
Mitutoyo Mode 8 (0-200 mm) 41 February 2013
Serie Numbor 8330622 Page sot3
1. Remacks:
1. Traceabity documents may bo reviewed by authorize representative ofthe UUT owner by sppoiniment
2 Measurement Unceriany, 0.0046 inch Eni Ses]; 0.03 mm pate Som) (Kea CFB5H)
1. Reference Standards Equipment:
MODEL NOUN IDNo. DUE DATE
4. SRTSCBBAAK Gage Block Set net 23 December 2014
3 SRT SSBATK Gage Block Set e074 11 danuary 2014
IV, Traceability of Standards Equipment Used:
1. Length - National Instiute of Standard & Technology (NIST) / LASER - Absolute Value of Natural Physical
Constant; Federal Ofice of Metrology (METAS) Suitzerans, Cenicate of Calibration No, 111-06480.; Pratt &
\Wmtney Cetitoate of Catbration No. LS-0045A-2011-01-19.
\, Reference Standards Document:
1. Local Calibration Precedue: GEM-P-20-002
CCalbeation Technician