Beruflich Dokumente
Kultur Dokumente
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Socket wrench • Torx Screwdriver
KIT COMPONENTS
• A) Radio trim panel • B) Radio housing • C) ISO brackets • D) ISO trim plate • E) ISO DDIN brackets
• F) ISO DDIN trim plate • G) Pocket • H) Axxess interface and harness (not shown)
REV. 7/24/2015 INST99-3010S
A B C D E
METRA. The World’s best kits.™ metraonline.com © COPYRIGHT 2004-2014 METRA ELECTRONICS CORPORATION
99-3010S
70
9 12
320
Kit Assembly
2. Remove (1) Phillips screw from each side of
– DIN radio provision with pocket......................................4 the front of the center console. (Figure B)
– ISO DIN radio provision with pocket................................4 3. Remove (2) Phillips screws per side from the
cover on the back of the center console then (Figure B)
– ISO DDIN radio provision.................................................5 unclip and remove the cover. (Figure C)
0 30
320
70
9 12
19
300
30 180
(Figure A) (Figure D)
2
99-3010S
0 30
70
9 12
100 200
19
300
30 180
320
3
99-3010S
Kit Assembly
DIN radio provision with pocket ISO DIN radio provision with pocket
1. Remove the metal DIN sleeve from 1. Remove the metal DIN sleeve and
the aftermarket radio. trim ring from the aftermarket radio.
2. Slide the sleeve into the Radio 2. Mount the ISO brackets to the
Housing and secure by bending radio with the screws supplied
the metal locking tabs down. with the radio. (Figure A)
(Figure A) (Figure A)
3. Snap the pocket into the bottom
3. Snap the pocket into the bottom opening of the Radio Housing.
opening of the Radio Housing. (Figure B)
(Figure B) (Figure A) 4. Slide the radio into the radio
4. Slide the radio back into the sleeve opening until the side clips engage.
until it clicks in. (Figure B) (Figure B)
5. Continue to Axxess Interface 5. Snap the ISO Trim Plate into the (Figure B)
Installation, and once completed, Radio Housing. (Figure C)
reassemble the dash in reverse
6. Continue to Axxess Interface
order of disassembly using the
Installation, and once completed,
99-3010S radio trim panel instead
reassemble the dash in reverse
of the factory panel.
order of disassembly using the
99-3010S radio trim panel instead
of the factory panel.
(Figure B) (Figure C)
4
99-3010S
(Figure C)
5
Axxess interface installation 99-3010S
Connections to • Connect the Gray wire to the right • Connect the Pink wire to the Pink rear positive wire.
be made front positive speaker output. wire located in the HVAC harness • Connect the Green/Black wire to
From the 16-pin harness to the • Connect the Gray/Black wire to the (ignore the writing on this wire, this is the left rear negative wire.
aftermarket radio: right front negative speaker output. NOT a “mute” wire).
• Connect the Red and White RCA jacks (b) for non-amplified models:
• Connect the (2) Red wires to the • Tape off and disregard the Green,
Green/Black, Purple, and Purple/ to the audio AUX-IN jacks (if equipped). • Leave intact the 4-pin harness
accessory wire. located between the 44-way and
Black wire, they will not be used in Note:
Note: If using the optional ASWC-1 or 22-way connector.
AX-LCD, there will be accessory wires this application. (1) This will allow you to retain the
3.5mm AUX-IN JACK located in the Note: The supplied 4-pin to 4-pin
there to connect as well. The following wires are for aftermarket resistor pad harness will not be
center console.
• Connect the Orange/White wire to the multimedia/navigation radios that used in this application.
illumination wire. (If the aftermarket (2) The jack can only be used if it is
provide these wires (if not required, tape • Cut the resistors from the Green,
a single jack.
radio has no illumination wire, tape off them off and disregard them): Green/Black, Purple, Purple/Black
the Orange/White wire). (3) If the jack has a USB port as
• Connect the Light Green wire to the wires right below the heat shrink
well, neither can be retained.
• Connect the Blue/White wire to the parking brake wire (if applicable). • Connect the Violet wire to the right
amp turn on wire (this wire must be • Connect the Blue/Pink wire to the (a) for amplified models: rear positive wire.
connected to hear sound from the speed sense wire (if applicable). • Disconnect the 4-pin harness • Connect the Violet/Black wire to
factory amplifier). • Connect the Green/Purple wire to the located between the 44-way the right rear negative wire.
• Connect the Brown wire to the mute reverse wire (if applicable). and 22-way connector, and then
• Connect the Green wire to the left
wire of the aftermarket radio. If the connect the supplied 4-pin to 4-pin
From the 3010S harness to the rear positive wire.
radio has no mute wire, tape it off and resistor pad harness.
disregard it. aftermarket radio: • Connect the Green/Black wire to
• Connect the Violet wire to the right
• Connect the Black wire to the the left rear negative wire.
• Connect the White wire to the left rear positive wire.
front positive speaker output. ground wire. • Connect the Violet/Black wire to From the 12-pin pre-wired ASWC-1
• Connect the White/Black wire to the • Connect the Yellow wire to the the right rear negative wire. harness to the aftermarket radio:
left front negative speaker output. battery wire. • Connect the Green wire to the left • The 12-pin harness is to be used in
6
Axxess interface installation 99-3010S
conjunction with the optional ASWC-1 Initializing the fully counterclockwise (all the way left). Vehicle customization
(not included) to retain steering wheel Axxess interface Turn clockwise to raise the chime level, with the optional
controls. If the ASWC-1 is not being Attention: If the Axxess interface loses and counterclockwise to lower the AX-LCD (sold separately)
used, disregard this harness. If it will chime level.
power for any reason, the following steps The AX-LCD allows the retention of the
be used, please refer to the ASWC-1
will need to be performed again. • When the chime is at the desired level, vehicles personalization menu that is
instructions for radio connections
• Initialize the interface by remove the keys from the ignition; this lost after removing the OE radio.
and programming.
turning the ignition on for 30 seconds, will lock the chime level in.
Note: The relay attached to the • Press the “ESC” button; “Press
then turn the ignition back off, then OnStar volume Enter to Set Language” will appear on
Axxess interface is only for audible
back on again. adjustment the screen.
turn signal clicks. No extra steps are
required to retain this feature, so Note: If using the ASWC-1, connect it • To change language, press the “Enter”
leave the relay as-is. after you initialize the Axxess interface, • Press the OnStar button to activate it. button, and then press the “Up” and
with the key in the off position. • While OnStar is speaking, press the “Down” buttons to change language.
Installing the • Start the vehicle, and then cycle the VOLUME UP or VOLUME DOWN buttons
Axxess interface • Once you have chosen the desired
A/C fan speed all the way to high, and on the steering wheel to raise or lower
language, press the “ESC” button to
With the key in the off position: then back to low. the OnStar level.
return to the main menu.
• Connect the 16-pin harness with • If the vehicle does not come
Chime volume • If you do not wish to change language,
stripped leads into the interface. equipped with steering wheel
adjustment you can scroll up and down through
• Connect the 3010S harness into controls, find the Black/Yellow wire on
the different settings with the “Up”
the interface. • With the vehicle on, shut the vehicle the 22-pin harness.
and “Down” buttons.
• Connect the 3010S harness into off and leave the keys in the ignition. • While OnStar is speaking, tap the
the vehicle. Open the driver’s door and leave it • Remember to press “Enter” to change
Black/Yellow wire to ground. Once the
open; chimes will be heard. the desired setting.
• With all connections completed, OnStar level is set, it will stay at that
reconnect the negative battery • Wait 10 seconds, and then with a small level until the Black/Yellow wire is
terminal. screwdriver, adjust the potentiometer tapped to ground again.
7
Installation instructions for 99-3010S
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
REV. 7/24/2015 INST99-3010S
METRA. The World’s best kits.™ metraonline.com © COPYRIGHT 2004-2014 METRA ELECTRONICS CORPORATION
Instrucciones de instalación para 99-3010S
A B C D E
METRA. The World’s best kits.™ metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION
99-3010S
70
9 12
100
19
320
300
30
70
9 12
19
300
30
70
30 180
9 12
19
320
(Figura A) (Figura D)
2
99-3010S
(Figura G)
0 30
70
9 12
100 200
19
300
30 180
320
3
99-3010S
4
99-3010S
5
Axxess interfaz de instalación 99-3010S
Conexiones que se salida negativa de la bocina izquierda • Conecte el cable rosa al cable rosa el cable negativo trasero derecho.
deben hacer del frente. localizado en el arnés del HVAC (ignore • Conecte el cable verde con el cable
Del arnés de 16 pins al radio de • Conecte el cable gris con la salida las letra del cable, NO es un cable positivo trasero izquierdo.
mercado secundario: positiva de la bocina derecha del frente. de “silencio”). • Conecte el cable verde/negro con
• Conecte los (2) cables rojos al cable • Conecte el cable gris/negro con la • Conecte los conectores RCA rojo y el cable negativo trasero izquierdo.
de accesorios. salida negativa de la bocina derecha blanco a los conectores AUX-IN de
audio (si incluye el equipamiento). (b) para modelos no amplificados:
Nota: Si usa el ASWC-1 o AX-LCD del frente.
Nota: • Deje intacto el arnés de 4 pins
opcional, también ahí habrá cables • Encinte e ignore el cable verde, verde/
localizado entre el conector de 44
accesorios que conectar. negro, púrpura y púrpura/negro, ya (1) Esto le permitirá retener el
vías y el conector de 22 vías.
que no se utilizarán en esta aplicación. conector de entrada auxiliar de
• Conecte el cable anaranjado/blanco Nota: El arnés del cojinete de
3.5mm AUX-IN localizado en la
con el cable de iluminación. (Si el Los siguientes cables son para radios de resistencia de 4 pins a 4 pins
consola central.
radio de mercado secundario no tiene mercado secundario con multimedios/ suministrado no se usará en esta
cable de iluminación, encinte el cable (2) El conector únicamente puede
navegación que tienen estos cables (si aplicación.
anaranjado/blanco). utilizarse si es un conector sencillo.
no se requieren, encíntelos e ignórelos): • Corte las resistencias de los cables
• Conecte el cable azul/blanco al (3) Si el conector también tiene
• Conecte el cable verde claro al cable verde, verde/negro, púrpura,
cable de encendido del amplificador un puerto USB, ninguno
de freno de mano (si aplica). púrpura/negro justo debajo del
(este cable debe estar conectado puede retenerse.
• Conecte el cable azul/rosa al cable termoencogimiento.
para escuchar sonido del amplificador del sensor de velocidad (si aplica). (a) para modelos amplificados: • Conecte el cable violeta con el cable
de fábrica). • Desconecte el arnés de 4 pins positivo trasero derecho.
• Conecte el cable verde/púrpura al
• Conecte el cable café con el cable cable de reversa (si aplica). localizado entre el conector de 44 • Conecte el cable violeta/negro con
de silencio del radio de mercado vías y de 22 vías y luego conecte el el cable negativo trasero derecho.
secundario. Si el radio no tiene cable Del arnés 3010S al radio de mercado arnés de cojinete de resistencia de • Conecte el cable verde con el cable
de silencio, encíntelo e ignórelo. secundario: 4 pins a 4 pins suministrado. positivo trasero izquierdo.
• Conecte el cable blanco con la salida • Conecte el cable negro al cable de tierra. • Conecte el cable violeta con el • Conecte el cable verde/negro con el
positiva de la bocina izquierda del frente. • Conecte el cable amarillo al cable de cable positivo trasero derecho. cable negativo trasero izquierdo.
• Conecte el cable blanco/negro con la la batería. • Conecte el cable violeta/negro con
6
Axxess interfaz de instalación 99-3010S
Del arnés ASWC-1 pre cableado de 12 Inicialización de la potenciómetro por completo hacia la Vehículo de
pins al radio de mercado secundario: interfas de Axxess izquierda (a la izquierda hasta topar). personalización con
• El arnés de 12 pins se debe usar Atención: Si la interfase Axxess pierde
Gire hacia la derecha para elevar el LCD opcional
junto con el ASWC-1 opcional (no nivel de los tonos y hacia la izquierda (se venden por separado)
su alimentación por algún motivo,
incluido) para retener los controles para disminuir el nivel de los tonos.
en el volante. Si no se está usando el deberán realizarse de nuevo los El AX-LCD le permite retener el menú
siguientes pasos. • Cuando los tonos estén en el nivel de personalización del vehículo que se
ASWC-1, ignore este arnés. Si se va a deseado, retire las llaves de la ignición;
utilizar, consulte las instrucciones de • Inicialice la interfase encendiendo pierde al desinstalar el radio original.
esto fijará el nivel de los tonos.
ASWC-1 para las conexiones del radio la marcha y espere 30 segundos, • Presione el botón “ESC”; la pantalla
y la programación. luego vuelva a apagar la ignición, y Ajuste del nivel mostrará “Presione Enter para
Nota: El relé adjunto a la interfase enciéndala una vez más. de OnStar configurar el idioma”.
Axxess únicamente es para los Nota: Si va a utilizar el ASWC-1, • Presione el botón OnStar • Para cambiar el idioma, presione el
chasquidos audibles de la señal conéctelo después de inicializar la botón “Enter” y luego presione los
para activarlo.
direccional. No se requieren interfase Axxess con la llave en la botones de “Arriba” y “Abajo” para
pasos adicionales para retener posición de apagado. • Mientras OnStar esté hablando,
cambiar el idioma.
esta característica, así que deje el presione los botones de AUMENTAR
• Prende el vehículo, y prensa los VOLUMEN o DISMINUIR VOLUMEN en • Cuando haya elegido el idioma
relevador como está.
botones para la velocidad del ventilador el volante para elevar o disminuir el deseado, presione el botón “ESC” para
Instalación de la de A/C alto y para bajo. nivel de OnStar. volver al menú principal.
Axxess interfase • Si no desea cambiar el idioma, puede
Ajuste del volumen • Si el vehículo no cuenta con controles
Con la llave en la posición de apagado: de los tonos en el volante, localice el cable negro/ desplazarse hacia arriba o hacia abajo
• Conecte el arnés de 16 pins con amarillo en el arnés de 22 pins. por los diferentes valores con los
terminales peladas a la interfase. • Con el vehículo encendido, apague el botones “Arriba” y “Abajo”.
• Mientras OnStar esté hablando, toque
• Conecte el arnés 3010S a la interfase. vehículo y deje las llaves en la ignición. el cable negro/amarillo a tierra. Una • Recuerde presionar Enter para cambiar
• Conecte el arnés 3010S al vehículo. Abra la puerta del conductor y déjela vez configurado el nivel de OnStar, el ajuste deseado.
• Cuando todas las conexiones estén abierta; se escucharán los tonos. permanecerá a ese nivel hasta que
hechas, vuelva a conectar la terminal • Espere 10 segundos y luego, con el cable amarillo/negro vuelva a
negativa de la batería. un pequeño destornillador, ajuste el tocarse a tierra.
7
Instrucciones de instalación para 99-3010S
METRA. The World’s best kits.™ metraonline.com © COPYRIGHT 2004-2015 METRA ELECTRONICS CORPORATION