Sie sind auf Seite 1von 2

B-Dupont 31P 7/10/01 4:02 PM Page 1

c DuPont Industrial Coatings


DUPONT® 31P
custom color
(voc conforming)
Type: Volume Solids:
Medium-long oil alkyd 50% Avg.
Description:
A satin gloss, premium quality, low VOC Weight Solids:
alkyd providing good color and gloss 69% Avg.
retention. Certified by U.S.D.A.
Suggested Uses: Weight Per Gallon:
• Topcoating of machinery or metal 10.8 Lb. Avg. 4.9 Kg. Avg.
parts.
• Architectural finish for walls, doors, and Suggested Film Build:
trim
• Topcoating structural steel and tanks in 4 mils (100 µm) wet 2 mils (50 µm) dry
non-corrosive environments
• Interior/Exterior Coverage Per Gallon:*
804 ft.2 (19.7 m2/L)@ 1 mil (typical)
Not Recommended For:
• Harsh chemical environments 402 ft.2 (9.8 m2/L) @ 2 mils suggested DFT
• Immersion service
Gloss:
Compatibility With Other Coatings:
Can be applied over suitable primer or Satin(25-40 @ 60°)
directly to wood, wallboard, or plaster.
Colors:
Resistance: More than 275 custom colors.
Weather—Very Good
Humidity—Good
Chemical—Fair in mild chemical Flash Point (Tag Closed Cup):
environments 105OF (41OC)
Maximum Service Temperature:
150°F(65°C) in continuous service. Shelf Life:
* Material losses during mixing and 1 year minimum
application will vary and must be taken
into consideration when estimating job Application Thinners:
requirements.
Spray: T-Y-3810
Volatile Organic Content (VOC) theoretical: Brush, Roll: T-Y-3819
Unthinned VOC 3.3 lbs./gal. (396 g/l)
Thinned 10% with Clean-Up Thinners:
TY-3819 or TY-3810 3.6 lbs./gal. (432 g/l)
T-Y-3819 or mineral spirits

Packaging:
1 and 5 gallon containers

Shipping Weight (Lbs.):


One Gallon Containers—11
Five Gallon Containers—53

All technical advice, recommendations and services are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable, and are intended for use by persons having skill
and know-how at their own discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from their use by Buyer in whole or in part. Such recommendations, technical advice
or services are not to be taken as a license to operate under or intended to suggest infringement of any existing patent.

H-19528
E-R3158 Printed in the U.S.A. 12/00
B-Dupont 31P 7/10/01 4:02 PM Page 2

DUPONT 31P
custom color
APPLICATION INSTRUCTIONS
(voc conforming)
Surface Preparation: Application Conditions:
Surface must be clean, dry, and free of any Do not apply if material, substrate, or ambient
oil or dirt. Prime bare steel with DuPont temperature is below 40°F(4°C) or above
67FD, DuPont 681FD or any other 110°F(43°C). The substrate should be at
appropriate primer. Prime block with 300P. least 5°F(3°C) above the dew point.
Relative humidity should be below 90%.
Activation:
No activation required. Cure Times (Hours @ 50%R.H.):
Pot Life: 50°F 70°F 90°F
Not applicable. Dry to Touch 48 8 5
Dry to Handle 96 32 24
Reduction: Dry to Recoat 64 16 12
No reduction should be necessary. However, Hard Dry 30 days 7 days 5 days
if conditions should require the addition of
thinner, T-Y-3810 or T-Y-3819 may be added Application Equipment:
up to 10% by volume. If more than 10% is • Apply by spray, brush, or roll.
required, contact your DuPont representative • Manufacturers listed below as a guide.
for specific recommendations. Others may be used. Changes in pressure
and tip size may be required to achieve
Storage Conditions: proper application.
Store in a dry, well ventilated area.
Storage temperatures should be between Roll:
–30°F(–34°C) and 120°F(48°C). 1
⁄4”-3⁄4” lambs wool or synthetic roll cover
such as One Coater.® Keep roll wet. Roll
Additional Comments: in one direction, rewet, then cross roll.
1. Bases are short filled to allow for colorant
addition: Conventional Air Spray:
1LB 30P – 124 oz./gallon Binks DeVilbiss Graco
2MB 30P – 120 oz./gallon Spray Gun: #18 or JGA502 or 800
3DB 30P – 116 oz./gallon #62 MBC510
4NB 30P – 112 oz./gallon Fluid Nozzle: 66 or FF or E 03 or 04
2. Formulated with Rule 66 non-photochemically 63PB
reactive solvents. Air Cap: 66PE or 704, 765, 02, 021,
3. Some colors are certified by the U.S.D.A. 63C or 78 or 03
for use in meat and poultry processing.
4. Some colors may require multiple coats to Airless Spray:
achieve hiding. Pump: 30:1 Bulldog (Graco)
High Pressure Filter: 100 Mesh
Safety: Fluid Hose: 3⁄8” x 150’ max.
Consult the Material Safety Data Sheet for Airless Gun: Graco 208663
this product prior to use. Tips: .015”-.025”
Minimum pressure to avoid fingering:
2000 psi

All technical advice, recommendations and services are rendered by the Seller gratis. They are based on technical data which the Seller believes to be reliable, and are intended for use by persons having skill
and know-how at their own discretion and risk. Seller assumes no responsibility for results obtained or damages incurred from their use by Buyer in whole or in part. Such recommendations, technical advice
or services are not to be taken as a license to operate under or intended to suggest infringement of any existing patent.

H-19528
E-R3158 Printed in the U.S.A. 12/00

Das könnte Ihnen auch gefallen