Beruflich Dokumente
Kultur Dokumente
com
Fe a t u r i n g
!
New Products
1 0 0 % F K M Co m m ercial
Fluoroelastomer
Neoprene Tubing
and more!
Table of Contents
Page:
visit us at warco.com
GENERAL PRODUCTION INFORMATION
Our unique combination of equipment and talent allows WARCO BILTRITE to be thoroughly proficient
in Large Volume, Short Run, and Custom Rubber production.
Please contact our sales department for quotations on volume in excess of 1,000 lbs or on any sheet, matting, extrusion, or molded rubber
products not featured in our catalog. Additionally, we would be pleased to quote you on any custom molding, extrusion, sheet, mats,
or matting products made to your requirements and specification.
For quotes, please contact customer service:
714-532-3355 (Tel) • 800-245-8748 (Tel) • 714-532-2238 (Fax) • sales@warco.com (Email)
Pricing: Sheet Rubber and Rubber Matting products are
priced per foot ($/FT). Rubber Mats, Molded Rubber Sheets
Sheet Rubber Roll Length: Sheet Rubber
Standard Roll approximate length ±10% Thickness Tolerance:
and Molded Bearing Pads are priced per each ($/EA). Extrusion (Standard RMA)
1/64” thick - 180 FT
is priced per foot ($/FT) or per 100 feet ($/CFT). Please call us
for a quote. 1/32” thick - 150 FT .031” and thinner ± .010“
1/16” thick - 100 FT .032” to .061” ± .012“
Minimum Purchase:
3/32” thick - 65 FT or 75 FT .062” to .124” ± .016”
Regularly Stocked Sheet Item: 1 Roll
Non-Regularly Stocked Item: See Product for details or call 1/8” thick - 50 FT .125” to .186” ± .020”
us at 1-800-254-8748 for quote 3/16” thick - 30 FT or 40 FT .187” to .374” ± .031”
Custom & Non-Catalog items: Please call for quote 1/4” thick - 25 FT or 40 FT .375” to .500” ± .047”
5/16” thick - 20 FT or 25 FT .501” to .750” ± .094”
Width Tolerance: Sheet Rubber comes trimmed or
untrimmed. Trimmed Sheet Rubber is provided either 36”, 48”, 3/8” thick - 16.5 FT or 30 FT .751” and thicker ± 10%
or 72“ wide ± 1”. Untrimmed Sheet Rubber is provided either 1/2” thick - 12.5 FT or 30 FT
Closer tolerances and custom
36” usable, 48” usable, or 55“ usable and can measure 3/4” thick - 30 FT thicknesses are available
approximately 3” in additional width. Custom widths are 1” thick - 30 FT & can be quoted on request:
available, please call for details. 1 1/4” thick - 30 FT Tel: 714-532-3355
Sheet Rubber Finish: Unless otherwise noted, sheet rubber Products may vary, please see product Toll-Free: 800-245-8748
has a standard smooth finish. Textured (fabric) finish and listing for specific roll lengths.
matte finish are available on most materials at an additional
cost. Please call for details. Special Services and Options Fraction to Decimal
Rubber Color: Unless otherwise noted, the standard color of are Available: Conversion Chart:
our rubber is black. Custom colors and color matching is Custom Formulations 1/64” 0.016”
available. Please call for details. Sheet Rubber Slitting 1/32” 0.031”
Test Reports: Short form test results, basic physicals, are Fabric, Paper & Matte Finish 1/16” 0.062”
available. Full test reports to particular specifications will be Talc Free 3/32” 0.093”
quoted on request. Certifications are sent with your order Stencilling 1/8” 0.125”
upon request at no charge. Color Matching 3/16” 0.187”
Physical Properties: The minimum physical properties in Tight Tolerances 1/4” 0.25”
this price list are obtained on ASTM test slabs and buttons. Custom Widths, Thicknesses 5/16” 0.312”
ASTM and Product Physical Values: ASTM basic and Lengths 3/8” 0.375”
requirements for physical properties are based on values Please call for details: 1/2” 0.5”
obtained from standard laboratory test specimens prepared Tel: 714-532-3355 5/8“ 0.625“
and tested in accordance with the applicable ASTM test Toll-Free: 800-245-8748 3/4” 0.75”
methods. Test results from specimens prepared from finished 7/8” 0.875”
All options may not be available on all products
products may not duplicate values obtained from standard
test specimens. Per ASTM D 2000, Section 7.1, Buyer agrees that
when standard test specimens are cut from finished parts in Price Page Key:
accordance with Practice D 3183, a deviation to the extent of
3 6”
Du ro me te r Ha rd n e ss
10% on tensile strength and elongation values is permissible. (Sh o re A ± 5 )
1 /1 6 ”
Freight Terms: F.O.B. our warehouse location, Freight 44228656
44228658
denoted with . Regularly Stocked
3 /3 2 ” $76.43 Items available for purchase by
prepaid and allowed by most economical routing on $54.57
44228661
$107.98
the foot at warco.com/buy-the-foot
shipments weighing 2,000 lbs or more to one destination, on 1 /8 ”
44228344 are denoted with
one purchase order, within the continental United States. 3 /1 6 ” $163.64
44228662
Freight allowance applies to WARCO BILTRITE Sheet rolls, $219.95
M
1 /4 ”
Matting rolls & Mats only. Free prepaid freight shipments are 44228666
A
G
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 3
when you don’t need a full roll
BuytheFoot Buy only what you need, when you need it.
WARCO BILTRITE is now offering select Sheet Rubber & Rubber Matting
parts for purchase in one foot increments with no minimum purchase.
Online
- Search for the Right Part
- View past & pending orders
- View Current On-Hand Inventory
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 4
Specification Index
With two full laboratories and 3,000+ rubber compounds, WARCO BILTRITE is proficient at
designing formulations to meet some of the world’s most stringent specifications. In
addition to the specifications listed below, WARCO BILTRITE’s technical and development
team is available to assist you with your specific requirements.
Please contact us for more information:
Tel: 714-532-3355 Toll-Free: 800-245-8748 Fax: 714-532-2238 Email: sales@warco.com
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 5
Specification Grade Sheet Rubber
Introducing
MIL-R-6855 Class 2 A & B (Oil Resistant Neoprene)
40 Duro: 1/16" 1/8"
BuytheFoot
60 Duro: 1/16"
w h e n yo u n
60 Duro: 1/32" 1/16" 3/32" 1/8" 3/16" 1/4"
70 Duro: 1/16" 3/32" 1/8" 3/16" 1/4"
80 Duro: 1/16" 1/8" 3/16" 1/4"
ly at
Available exclusive Commercial Neoprene - Matte Finish - Style 12
warco.com 50 Duro: 1/16" 1/8" 1/4"
60 Duro: 1/16" 3/32" 1/8" 3/16" 1/4"
70 Duro: 1/16" 1/8" 3/16" 1/4"
80 Duro: 1/8" 1/4"
Mid-Grade Neoprene - 5100 Series
When you don't need a full 30 Duro: 1/8"
40 Duro: 1/32" 1/16" 1/8"
roll of sheet rubber or rubber 50 Duro: 1/32" 1/16" 1/8"
matting - Buy the Foot! 60 Duro:
70 Duro:
1/16" 1/8"
1/16"
Premium Neoprene
WARCO BILTRITE is now offering 60 Duro: 1/16" 1/8"
select Sheet Rubber and Rubber 70 Duro: 1/8"
90 Duro: 1/16" 1/8"
Matting parts (listed here) for
Nitrile Sheet Rubber
purchase in one foot increments
Commercial Nitrile - Style 35
with no minimum purchase. 40 Duro: 1/16" 1/8" 3/16" 1/4"
50 Duro: 1/16" 1/8" 3/16" 1/4"
Need a few feet of rubber 60 Duro:
70 Duro:
1/32"
1/32"
1/16" 3/32" 1/8" 3/16" 1/4"
1/16" 1/8" 1/4"
and don't want to be stuck Premium Nitrile
40 Duro: 1/8"
with the rest of the roll? 60 Duro: 1/16" 1/8"
Buy the Foot! 70 Duro:
80 Duro:
1/16" 1/8" 1/4"
1/16"
90 Duro: 1/32" 1/16" 1/8"
For more information, please visit WARCO White® FDA Nitrile
warco.com/buy-the-foot 45 Duro: 1/8" 1/4"
55 Duro: 1/32" 1/16" 3/32" 1/8" 1/4"
65 Duro: 1/16"
80 Duro: 1/8"
FDA Nitrile - Style 37
Proudly manufactured in the USA since 1910. 60 Duro: 1/16" 1/8" 3/16" 1/4"
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 6
Natural Rubber Sheet
Introducing
Natural Rubber - Style 28
40 Duro: 1/16" 1/8" 3/16" 1/4"
BuytheFoot
EPDM Sheet Rubber
Commercial EPDM - Style 40
50 Duro: 1/16" 1/8" 3/16" 1/4"
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 7
Commercial Neoprene - Style 10 Atemperature
smooth finish general purpose sheet with low
flexibility and oil resistance. Resists
rotting, checking, and cracking due to weather exposure. Designed to meet ASTM specifications for 1 BC Material.
Finish: Smooth Color: Black Trim: Trimmed Non-Stock Minimum: Please call 1-800-245-8748 for quote
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 8
Mid-Grade Neoprene - 5100 Series Aapplications
premium grade blended sheet for
requiring a higher percentage of
Neoprene and wider temperature range than standard commercial grade. This Neoprene formula has great resistance to
weathering and moderate resistance to oil and gasoline.
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
30 ASTM D 2000
1/32 thru 1/4 36, 48 450 300 –30ºF to +200ºF 2.2 lb
030E1084 M1BC 303
40 ASTM D 2000
1/32 thru 1/4 36, 48 450 300 –30ºF to +200ºF 2.45 lb
040E0423 M1BC 403
50 ASTM D 2000
1/64 thru 1/2 36, 48 1000 300 –30ºF to +200ºF 2.46 lb
050E0357 M1BC 507
60 ASTM D 2000
1/64 thru 1/2 36, 48 1000 300 –30ºF to +200ºF 2.48 lb
060E0264 M1BC 607
70 ASTM D 2000
1/64 thru 1/4 36, 48 1000 200 –30ºF to +200ºF 2.52 lb
070E0321 M1BC 707
80 ASTM D 2000
1/32 thru 1/4 36, 48 1000 100 –30ºF to +200ºF 2.75 lb
080E1109 M1BC 807
30 1/32 thru 1/4 36, 48 450 300 –30ºF to +220ºF 2.43 lb ASTM D 2000
030E 0242 M1BC 303
40 1/64 thru 1/4 36, 48 1000 400 –30ºF to +220ºF 2.46 lb ASTM D 2000
040E 0247 M1BC 407
50 1/64 thru 1/4 36, 48 1450 350 –30ºF to +220ºF 2.54 lb ASTM D 2000
050E 0503 M1BC 510
60 1/64 thru 1/4 36, 48 1450 350 –30ºF to +220ºF 2.65 lb ASTM D 2000
060E 0306 M1BC 610
70 1/64 thru 1/4 36, 48 1450 250 –30ºF to +220ºF 2.77 lb ASTM D 2000
070E 0313 M1BC 710
80 1/64 thru 1/4 36, 48 1450 100 –30ºF to +220ºF 2.79 lb ASTM D 2000
080E 0325 M1BC 810
90 1/32 thru 1/4 36, 48 1000 100 –30ºF to +220ºF 2.81 lb ASTM D 2000
090E 0228 M1BC 907
FDA Neoprene
This off-white Neoprene material contains FDA approved ingredients per 21 CFR 177.2600, an FDA regulation dealing with
rubber articles articles intended for repeated food exposure.
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
FDA Approved
40 1/32 thru 1/4 36, 48 600 400 –30ºF to +220ºF 2.65 lb Ingredients per
0 4 0 E1 0 5 8
21 CFR 177.2600
FDA Approved
55 1/32 thru 1/4 36, 48 800 350 –30ºF to +220ºF 2.98 lb Ingredients per
0 5 5 E1 0 5 3
21 CFR 177.2600
FDA Approved
60 1/32 thru 1/4 36, 48 1000 300 –30ºF to +220ºF 2.98 lb Ingredients per
0 6 0 E1 0 6 2
21 CFR 177.2600
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 9
Neoprene Performance Molded Sheets
Available in 36”x36” or 48”x48” - Longer lengths available, please call for quote.
Finish: Smooth Color: Black Trim: Trimmed Non-Stock Minimum: Please call for quote
Durometer Ultimate Temperature Estimated Weight
Thickness Sizes* Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (5/16” x 36”)
20 36 x 36
1/8 thru 4 500 550 –30ºF to +200ºF 5.5 lb ---
020E0241 48 x 48
40 36 x 36
1/8 thru 4 500 350 –30ºF to +200ºF 5.4 lb ---
040E0913 48 x 48
50 36 x 36
1/8 thru 4 500 300 –30ºF to +200ºF 5.88 lb ---
050E0914 48 x 48
60 36 x 36
1/8 thru 4 700 250 –30ºF to +200ºF 5.9 lb ---
060E0915 48 x 48
70 36 x 36
1/8 thru 4 700 150 –30ºF to +200ºF 6.15 lb ---
070E0916 48 x 48
80 36 x 36
1/8 thru 4 700 100 –30ºF to +200ºF 6.4 lb ---
080E0888 48 x 48
*For 30 FT lengths, please see Commercial Neoprene - Style 10.
ASTM D 2000
40 1/64 thru 1/4 36, 48 1450 500 –50ºF to +220ºF 2.45 lb M2BC 410
A14 B14 C12 E034 F17
ASTM D 2000
50 1/64 thru 1/4 36, 48 1450 350 –60ºF to +220ºF 2.53 lb M2BC 510
A14 B14 C12 E034 F17
ASTM D 2000
60 1/64 thru 1/4 36, 48 1450 350 –50ºF to +220ºF 2.69 lb M2BC 610
A14 B14 C12 E034 F17
ASTM D 2000
70 1/64 thru 1/4 36, 48 1450 250 –60ºF to +220ºF 2.67 lb M2BC 710
A14 B14 C12 E034 F17
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 10
MIL-R-3065 SC (Neoprene)
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
MIL-R-3065 SC
30 1/32 thru 1/4 36, 48 1000 400 –60ºF to +220ºF 2.39 lb
310 F1
40 MIL-R-3065 SC
1/64 thru 1/4 36, 48 1000 400 –60ºF to +220ºF 2.47 lb
410 F2
50 MIL-R-3065 SC
1/64 thru 1/4 36, 48 1500 350 –60ºF to +220ºF 2.61 lb
515 F2
60 MIL-R-3065 SC
1/64 thru 1/4 36, 48 1500 300 –60ºF to +220ºF 2.65 lb
615 F2
70 MIL-R-3065 SC
1/64 thru 1/4 36, 48 1500 250 –60ºF to +220ºF 2.61 lb
715 F2
80 MIL-R-3065 SC
1/64 thru 1/4 36, 48 1500 100 –60ºF to +220ºF 2.61 lb
815 F1
AMS 3205
50 1/64 thru 1/4 36, 48 1500 350 –40ºF to +220ºF 2.53 lb Low Temperature
(Neoprene)
AMS 3208
50 1/64 thru 1/4 36, 48 1200 300 –30ºF to +220ºF 2.51 lb Weather Resistant
(Neoprene)
AMS 3215
70 1/64 thru 1/4 36, 48 1500 250 –30ºF to +220ºF 2.45 lb Fuel Resistant
(Nitrile)
Anti-Microbial Neoprene This specially formulated sheet product line prevents the growth of
bacteria, fungi, and yeasts while avoiding obstacles that organic
biocides have posed in the past. This product can alleviate cleaning challenges in food-processing, medical, industrial, and
other applications prone to microbial growth.
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 11
Low Smoke, Low Flame, Low Toxicity Neoprene
Another example of the extensive capabilities of our laboratory. WARCO BILTRITE fire retardant elastomers offer significant
benefits for gasketing and noise control inside railcars. The unique formulations of our highly engineered elastomers allow
to safely resist the distribution of flame while emitting very low amounts of toxic smoke. This material is designed and
formulated to meet the mass transit industry’s most demanding requirements and specifications for smoke generation
(ASTM E 662), flame propogation (ASTM C 542), and toxic fume production (SMP 800-C). Rail transit, truck, bus or automotive,
WARCO BILTRITE has the material to meet your requirements.
Finish: Nylon Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 12
Commercial Nitrile - Style 35 Arange
smooth finish blended Nitrile sheet, which is offered in a
of five durometers (40 thru 80 durometer) in order to
perform in a wide variety of applications. Designed to meet ASTM specifications for 1BF material.
Finish: Smooth Color: Black Trim: Trimmed Non-Stock Minimum: Please call 1-800-245-8748 for quote
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
Premium Nitrile This material is formulated to give excellent fuel and oil resistance and a longer service life
in demanding applications.
Finish: Smooth Color: Black Trim: UnTrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
40 1/64 thru 1/4 36, 48 1000 450 –30ºF to +220ºF 2.22 lb ASTM D 2000
040P0179 M1BG 407
50 1/64 thru 1/4 36, 48 1000 350 –30ºF to +220ºF 2.32 lb ASTM D 2000
050P0266 M1BG 507
60 1/64 thru 1/4 36, 48 1450 300 –30ºF to +220ºF 2.36 lb ASTM D 2000
060P0187 M1BG 610
70 1/64 thru 1/4 36, 48 1450 250 –30ºF to +220ºF 2.48 lb ASTM D 2000
070P0135 M1BG 710
80 1/64 thru 1/4 36, 48 1450 125 –30ºF to +220ºF 2.59 lb ASTM D 2000
080P0206 M1BG 810
90 ASTM D 2000
1/32 thru 1/4** 36, 48 1450 100 –30ºF to +220ºF 2.34 lb
090P0270 M1BG 910
*1/4” thick 90 durometer material available in slabs only.
FDA Nitrile - Style 37 Style 37 is specially formulated for its whiteness, used in food,
phamaceutical, and cosmetic processing. Made from FDA-approved ingredients
per 21CFR 177.2600, it is non-marking, non-allergenic, and safe to use for repeated food exposure. It has good oil and
abrasion resistance and handles oily and greasy food products well. This product conforms with 3-A Sanitary 18-03
requirements for multiple use rubber Class III and Class IV.
Finish: Smooth Color: White Trim: Trimmed Non-Stock Minimum: Please call 1-800-245-8748 for quote
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 13
WARCO White® FDA Nitrile Aswhiteness
its name implies, this material is specially formulated for its
and is used extensively in food and pharmaceutical
environments. It is formulated with FDA-approved ingredients. It is non-toxic, non-marking and non-allergenic. It exhibits
good abrasion resistance and handles oily and greasy food products well. All materials are made with FDA approved
ingredients per 21 CFR 177.2600 and are intended for repeated food exposure.
Finish: Smooth Color: White Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness Inches Inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
MIL-R-6855E
40 1/64 thru 1/4 36, 48 1100 450 –50ºF to +220ºF 2.15 lb
Class 1 Grade 40
MIL-R-6855E
50 1/64 thru 1/4 36, 48 1200 350 –50ºF to +220ºF 2.38 lb
Class 1 Grade 50
MIL-R-6855E
60 1/64 thru 1/4 36, 48 1300 300 –50ºF to +220ºF 2.42 lb
Class 1 Grade 60
MIL-R-6855E
70 1/64 thru 1/4 36, 48 1400 200 –50ºF to +220ºF 2.5 lb
Class 1 Grade 70
MIL-R-6855E
80 1/64 thru 1/4 36, 48 1600 150 –50ºF to +220ºF 2.46 lb
Class 1 Grade 80
MIL-R-3065 SB (Nitrile)
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
MIL-R-3065 SB
40 1/64 thru 1/4 36, 48 1000 450 –60ºF to +220ºF 2.22 lb 410 F2
MIL-R-3065 SB
50 1/64 thru 1/4 36, 48 1500 400 –60ºF to +220ºF 2.22 lb 515 F2
MIL-R-3065 SB
60 1/64 thru 1/4 36, 48 1500 300 –60ºF to +220ºF 2.28 lb 615 F2
MIL-R-3065 SB
70 1/64 thru 1/4 36, 48 1500 250 –60ºF to +220ºF 2.35 lb 715 F2
MIL-R-3065 SB
80 1/64 thru 1/4 36, 48 1500 125 –40ºF to +220ºF 2.45 lb 815 F1
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 14
ASTM D 2000 M5BG (Nitrile)
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Linear Foot
Shore A ± 5 min. % (1/8” x 36”)
ASTM D 2000
40 1/64 thru 1/4 36, 48 1000 450 –40ºF to +220ºF 2.14 lb M5BG 407
A14 B14 E014 E034 F17
ASTM D 2000
50 1/64 thru 1/4 36, 48 1000 350 –40ºF to +220ºF 2.22 lb M5BG 507
A14 B14 E014 E034 F17
ASTM D 2000
60 1/64 thru 1/4 36, 48 1450 300 –40ºF to +220ºF 2.41 lb M5BG 610
A14 B14 E014 E034 F17
ASTM D 2000
70 1/64 thru 1/4 36, 48 1450 250 –40ºF to +220ºF 2.41 lb M5BG 710
A14 B14 E014 E034 F17
MIL-G-1149
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Linear Foot
Shore A ± 5 min. % (1/8” x 36”)
MIL-G-1149 Type 1
50 1/64 thru 1/4 36, 48 1000 300 –30ºF to +200ºF 2.67 lb Class 1 Grade 50
(Neoprene)
MIL-G-1149 Type 1
50 1/64 thru 1/4 36, 48 1000 300 –40ºF to +180ºF 2.13 lb Class 2 Grade 50
(SBR)
MIL-G-1149 Type 1
50 1/64 thru 1/4 36, 48 1000 300 –40ºF to +200ºF 2.32 lb Class 5 Grade 50
(Nitrile)
MIL-R-2765 (Nitrile)
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
40 1/64 thru 1/4 36, 48 1000 300 –50ºF to +220ºF 2.24 lb MIL-R-2765
A Nitrile material designed specifically for the transformer oil market; helping
Transformer Oil Nitrile to dissipate the likelihood of high electrostatic charging tendencies. These
highly engineered materials, in addition to meeting their respective ASTM D 2000 line call-outs, meet industry specification
GE A12C11E7.
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches Inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
ASTM D 2000
60 5BG 620 A14 B14 E034;
1/32 thru 1/2 36, 48 2000 300 –30ºF to +250ºF 2.36 lb
060P0996 General Electric
EA12C11E7
ASTM D 2000
70 5BG 720 A14 B14 E034;
1/32 thru 1/2 36, 48 2000 250 –20ºF to +250ºF 2.42 lb
070P0807 General Electric
EA12C11E7
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 15
Bio-Diesel Nitrile Specially designed and developed for use in environments where alternative fuels are
present. Immersion test results indicate that these materials are compatible with alternative
fuels and are suitable for Bio-Diesel B20 (20% Bio-Diesel and 80% Petroleum Diesel) & Bio-Diesel B100 (100% Bio-Diesel).
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Features
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
60 Compatible with
1/32 thru 1/2 36, 48 1500 300 –30ºF to +220ºF 2.39 lb
060P0678 Bio-Diesel B20 & B100
70 Compatible with
1/32 thru 1/2 36, 48 1500 250 –30ºF to +220ºF 2.4 lb
070P1042 Bio-Diesel B20 & B100
Red Rubber SBR - Style 20 Anno oileconomical red sheet for use in low pressure applications with
resistant requirements.
100 lb (half) rolls are also available. Please call for quote.
Finish: Smooth (Also available in fabric finish) Color: Red (Also available in Black) Trim: Trimmed
Non-Stock Minimum: Please call 1-800-245-8748 for quote
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
Specification Grade SBR A premium grade SBR sheet with a high tensile strength. Well suited for
the heating and plumbing trades. Has good aging, abrasion and tear
resistant properties. Refer to physical properties and ASTM data in assessing suitability for intended applications.
Finish: Smooth Color: Red (Also available in Black) Trim: Untrimmed
Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
ASTM D 2000
75 1/16 thru 1/4 36, 48 450 150 –40ºF to +180ºF 3.0 lb M1AA 703 Z1
075A0370
(Z1 = 75 ± 5 Durometer)
75 1/16 thru 1/4 36 700 150 –20ºF to +170ºF 2.7 lb ASTM D 1330 Grade 1
8008
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 16
Natural Rubber - Style 28 Excellent physical properties such as superior resilience, tensile,
elongation, and abrasion resistance. Style 28 is a tan floating stock
and is produced entirely with FDA approved ingredients. It has good tear strength and is resistant to water most salts, mild
acids and other chemicals. Not suited for environments involving ozone, strong acids, animal fats, oils, greases and most
hydrocarbons. Non-marking and safe to use for repeated food exposure.
Finish: Smooth Color: Tan Trim: Trimmed Non-Stock Minimum: Please call 1-800-245-8748 for quote
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
40 ASTM D 2000
1/64 thru 1/4 36, 48 2500 500 –40ºF to +160ºF 1.91 lb
040R0246 M1AA 417
50 1/64 thru 1/4 36, 48 2500 400 –40ºF to +160ºF 2.07 lb ASTM D 2000
050R0566 M1AA 517
60 1/64 thru 1/4 36, 48 2500 400 –40ºF to +160ºF 2.28 lb ASTM D 2000
060R0134 M1AA 617
Pure Gum Floating Natural Rubber Light Tan Pure Gum Floating stock has superior
resilience, tensile, elongation and abrasion
resistance properties. Light Tan Natural Rubber is produced entirely with FDA approved ingredients per 21 CFR 177.2600. It
has good tear strength and is resistant to water, most salts, mild acids, and many other chemicals. Not suited for
environments involving ozone, strong acids, animal fats, oils, greases, and most hydrocarbons. Non-marking and safe to use
for repeated food exposure.
Finish: Smooth Color: Light Tan (Also available in Black) Trim: Untrimmed
Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile* Specifications
Hardness Inches Inches min. psi Elongation* Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 17
EZ Cut Non-Floating Gum Natural Rubber
Superior resilience, tensile, elongation and abrasion resistance properties. It has good tear strength and is resistant to water,
most salts, mild acids, and many other chemicals. Made with FDA approved ingredients per 21 CFR 177.2600.
Finish: Smooth Color: Dark Tan Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
40 ASTM D 2000
1/8 thru 2 36, 48 2500 500 –40ºF to +160ºF 1.93 lb
040R0573 M4AA 421 F17 G21
Commercial EPDM - Style 40 Our most economical EPDM sheet offered. Intended to
be used in less critical applications where temperatures are of an intermittent nature.
Finish: Smooth Color: Black Trim: Trimmed Non-Stock Minimum: Please call 1-800-245-8748 for quote
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 18
Premium EPDM - Style 45
High Grade EPDM is suited for applications where a high performance rating is required. It exhibits excellent resistance to
heat, ozone and sunlight and has good temperature flexibility.
Finish: Smooth Color: Black Trim: Trimmed Non-Stock Minimum: Please call 1-800-245-8748 for quote
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
40 1/64 thru 1/4 36, 48 1015 300 –50ºF to +220ºF 2.03 lb ASTM D 2000
0 4 0 K0 0 3 8 M2BA 407 C12 F17
50 1/64 thru 1/4 36, 48 1015 300 –50ºF to +220ºF 2.2 lb ASTM D 2000
0 5 0 K0 0 4 2 M2BA 507 C12 F17
60 1/64 thru 1/4 36, 48 1015 300 –50ºF to +220ºF 2.22 lb ASTM D 2000
0 6 0 K0 0 2 0 M2BA 607 C12 F17
70 1/64 thru 1/4 36, 48 1015 200 –50ºF to +220ºF 2.28 lb ASTM D 2000
0 7 0 K0 0 5 2 M2BA 707 C12 F17
80 1/64 thru 1/4 36, 48 1450 150 –50ºF to +220ºF 2.28 lb ASTM D 2000
0 8 0 K0 0 3 6 M2BA 810 C12 F17
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 19
Peroxide Cure EPDM Peroxide cured EPDM provides exceptional heat and aging stability and better
compression set performance at higher temperatures. Most peroxides do not
bloom and have better color control and stability.
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
MIL-R-21252 (EPDM)
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
80 1/64 thru 1/4 36, 48 2000 150 –60ºF to +300ºF 2.32 lb MIL-R-83285 Grade 80
MIL-R-900 (EPDM)
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
45 1/64 thru 1/4 36, 48 1000 300 –40ºF to +180ºF 2.1 lb MIL-R-900
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 20
ASTM D 2000 M4AA (EPDM)
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
ASTM D 2000
40 1/64 thru 1/4 36, 48 1450 400 –60ºF to +300ºF 2.1 lb M4AA 407
A13 B13 C12 F17
ASTM D 2000
50 1/64 thru 1/4 36, 48 1450 400 –60ºF to +300ºF 2.08 lb M4AA 510
A13 B13 C12 F17
ASTM D 2000
60 1/64 thru 1/4 36, 48 1450 350 –60ºF to +300ºF 2.14 lb M4AA 610
A13 B13 C12 F17
ASTM D 2000
70 1/64 thru 1/4 36, 48 1450 250 –60ºF to +300ºF 2.2 lb M4AA 710
A13 B13 C12 F17
65 1/8 thru 1 48 1500 300 –20ºF to +170ºF 3.3 lb Good abrasion and
8055 tear resistance
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 21
AASHTO Unsupported Natural Rubber Bearing Pads - Style 72
Natural Rubber Unsupported AASHTO Bearing Pads are available in Grade 2 (other grades also available) in lengths up to
30 feet. Longer lengths available, please call for quote. Also available in 36” x 36” and 48” x 48” slabs.
Finish: Smooth Color: Black Trim: Trimmed Non-Stock Minimum: Please call 1-800-245-8748 for quote
Durometer Ultimate Weight
Thickness Width Tensile Temperature
Hardness Elongation Per Foot Specification
Shore A ± 5
inches inches min. psi
min. %
Range (1/2” x 36”)
50 AASHTO Grade 2*
1/4 thru 1 48 2250 450 –40ºF to +160ºF 11.8 lb
8091 Natural Rubber
60 AASHTO Grade 2*
1/4 thru 1 48 2250 400 –40ºF to +160ºF 12 lb
8093 Natural Rubber
70 AASHTO Grade 2*
1/4 thru 1 48 2250 300 –40ºF to +160ºF 12.2 lb
8095 Natural Rubber
Certain states specify requirements other than standard AASHTO specifications. When ordering, identify all requirements or submit
individual state specifications. Above meets the Standard Specifications for Highway Bridges, adopted by the American Associa-
tion of State Highway & Transportation Officials, Sixteenth Edition 1993, Section M251-92, Level 1.
*Other AASHTO grades are available. Please contact customer service for details.
50 1/8 thru 1/2 36, 48 2250 400 –40ºF to +220ºF 2.54 lb AASHTO Grade 3
0 5 0 E0 0 5 2 Neoprene
60 1/8 thru 1/2 36, 48 2250 350 –40ºF to +220ºF 2.56 lb AASHTO Grade 3
0 6 0 E0 0 5 4 Neoprene
70 1/8 thru 1/2 36, 48 2250 300 –40ºF to +220ºF 2.60 lb AASHTO Grade 2
0 7 0 E0 0 5 6 Neoprene
Certain states specify requirements other than standard AASHTO specifications. When ordering, identify all requirements or submit
individual state specifications. Above meets the Standard Specifications for Highway Bridges, adopted by the American
Association of State Highway and Transportation Officials, Sixteenth Edition 1993, Section M251-92, Level 1.
*Other AASHTO grades are available. Please contact customer service for details.
50 1/4 thru 1 36x36 2250 400 –40ºF to +220ºF 10.15 lb AASHTO Grade 3
050E0979 48x48 Neoprene
60 1/4 thru 1 36x36 2250 350 –40ºF to +220ºF 10.31 lb AASHTO Grade 3
060E0986 48x48 Neoprene
70 1/4 thru 1 36x36 2250 300 –40ºF to +220ºF 10.39 lb AASHTO Grade 2
070E0869 48x48 Neoprene
Certain states specify requirements other than standard AASHTO specifications. When ordering, identify all requirements or submit
individual state specifications. Above meets the Standard Specifications for Highway Bridges, adopted by the American
Association of State Highway and Transportation Officials, Sixteenth Edition 1993, Section M251-92, Level 1.
*Other AASHTO grades are available. Please contact customer service for details.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 22
100% FKM Commercial Fluoroelastomer: 66% Fluorine
This material exhibits a broad range of resistance to oils, fuels, lubricants and most mineral acids. It has very good resistance
to many aliphatic hydrocarbon fluids that act as solvents for many other rubbers.
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: Please call for minimums and availability.
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Features
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
75 1/32 - 1/4 36, 48 1000 175 –20ºF to +400ºF 3.63 lb 100% virgin FKM
075F0200
75 1/32 thru 1/4 36, 48 1000 175 –20ºF to +400ºF 4.4 lb 100% DuPont Viton® FKM
075F0123
60 1/16 - 1/4 36, 48 1000 200 –20ºF to +450ºF 3.79 lb ASTM D 2000
060F0053 M1HK 607
70 1/32 - 1/4 36, 48 1000 175 –20ºF to +450ºF 3.58 lb ASTM D 2000
070F0052 M1HK 707
80 1/32 - 1/4 36, 48 1000 150 –20ºF to +450ºF 3.61 lb ASTM D 2000
080F0054 M1HK 807
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 23
100% FKM Premium Viton® B: 68% Fluorine Viton® B has greater
resistance a n d retains
flexibility better after dry heat aging than Viton® A. It is recommended for applications requiring maximum retention of
elastic properties combined with good mechanical properties. Viton® B offers superior resistance to both diluted and
concentrated aggressive acids.
Finish: Smooth Color: Black Trim: Untrimmed
Non-Stock Minimum:Please call for minimums and availability.
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
70 ASTM D 2000
1/32 - 1/4 36, 48 1000 175 –20ºF to +450ºF 3.75 lb
070F0195 M1HK 707
75 ASTM D 2000
1/32 - 1/4 36, 48 1000 150 –20ºF to +450ºF 3.81 lb
075F0165 M1HK 807 Z*
*Z = 75 ± 5 Durometer
100% FKM FDA Viton® A: 66% Fluorine Perfect for food and lab applications
where FDA compliance is required.
This material has good chemical resistance, high temperature properties and is resistant to corrosives.
Finish: Smooth Color: Black Trim: Untrimmed
Non-Stock Minimum: Please call for minimums and availability.
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Linear Foot
Shore A ± 5 min. % (1/8” x 36”)
FDA approved
75 1/64 thru 1/4 36, 48 700 150 –20ºF to +450ºF 3.63 lb ingredients per
075F 0151
21 CFR 177.2600
75 Mil-R-83248C
1/64 thru 1/4 36, 48 1600 125 –20ºF to +500ºF 3.63 lb
075F0081 Type 2 Class 1
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 24
COMSIL® Commercial Silicone WARCO BILTRITE’s commercial grade silicone sheet is
designed to be used in applications where physical
properties are not critical but extreme temperature (high or low) resistance is still needed. This material also provides
excellent UV and ozone resistance. It is non-toxic, chemically inert and fungus resistant.
Finish: Smooth Color: Red (Also available in Black, White, & Gray) Trim: Untrimmed
Non-Stock Minimum: Please call for minimums and availability.
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Features
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
40 1/32 thru 1/4 36, 48 725 300 –80ºF to +450ºF 2.48 lb ZZ-R-765 2A & 2B, AMS 3301,
040S0561 ASTM D 2000 M1GE 405
50 1/32 thru 1/4 36, 48 725 250 –80ºF to +450ºF 2.5 lb ZZ-R-765 2A & 2B, AMS 3302,
050S0562 ASTM D 2000 M1GE 505
60 1/32 thru 1/4 36, 48 725 200 –80ºF to +450ºF 2.67 lb ZZ-R-765 2A & 2B, AMS 3303,
060S0563 ASTM D 2000 M1GE 605
70 1/32 thru 1/4 36, 48 725 150 –80ºF to +450ºF 2.71 lb ZZ-R-765 2A & 2B, AMS 3304,
070S0564 ASTM D 2000 M1GE 705
FDA Silicone This Silicone material is designed for applications where food or consumables are present. FDA
Silicone is low volatile, peroxide-free and does not discolor over time. The ingredients used to make
this product are listed in CFR 177.2600, an FDA regulation dealing with rubber articles that are intended for repeated food
exposure. This material is ozone and UV resistant.
Finish: Smooth Color: Red (White is also available) Trim: Untrimmed
Non-Stock Minimum: Please call for minimums and availability.
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 25
Butyl Butyl (also known as Isobutylene-isoprene) is impermeable to air and used in many applications requiring airtight
rubber. Butyl rubber has outstanding resistance to gases, vapors, heat aging, oxygen, ozone, sunlight, abrasion and
tearing. It has excellent resistance to alkalis and acids and is good for electrical insulation.
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile Specifications
Hardness inches inches min. psi Elongation Range Per Foot
Shore A ± 5 min. % (1/8” x 36”)
40 1/32 thru 1/4 36, 48 1000 400 –40ºF to +180ºF 2.09 lb ASTM D 2000
040T0083 M1AA 407
50 1/32 thru 1/4 36, 48 1000 400 –40ºF to +180ºF 2.2 lb ASTM D 2000
050T0055 M1AA 507
60 1/32 thru 1/4 36, 48 1000 300 –40ºF to +180ºF 2.24 lb ASTM D 2000
060T0056 M1AA 607
70 1/32 thru 1/4 36, 48 1450 250 –40ºF to +180ºF 2.3 lb ASTM D 2000
070T0080 M1AA 710
70* 1/16 thru 1/4 36, 48 800* 150* 4.0 oz Polyester 2.34 lb Polyester-Inserted
0 7 0 E1 0 2 8 Sheet
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 26
Cloth-Inserted SBR - Regular Cotton Ply
Cloth reinforcement enhances dimensional stability in flanged gasket applications with high compression loads. Suitable
for use in air, hot water, low pressure steam, and hydraulic services. An SBR compound reinforced with a close weave cotton
fabric. This construction includes one ply of cotton fabric for each 1/16” thickness.
Finish: Smooth Color: Black Trim: Untrimmed Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Fabric Temperature Estimated Weight
Thickness Width Tensile* Features
Hardness* inches inches min. psi Elongation* Type Range* Per Foot
Shore A ± 5 min. % (1/8” x 36”)
65* 1/16 thru 1/4 36, 48 1300* 300* Cotton –30ºF to +170ºF* 2.75 lb Cotton-Inserted
06 5A04 47 Sheet
65* 1/8 thru 1/4 36, 48 1300* 300* Cotton –30ºF to +170ºF 2.75 lb Cotton-Inserted
065A0447 Sheet
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 27
HHP-151F Cloth-Inserted (CI) Sheet Designed for ventilating systems and for
flange joints for water or brine systems to
withstand 250 pounds of pressure. A typical application is a flange gasket in which the compression loads are so high that
non-reinforced rubber would squeeze or extrude out between the flanges.
Finish: Smooth Color: Black Trim: Untrimmed Fabric Type: Cotton
Non-Stock Minimum: 2 rolls (For 1 roll, please call for quote)
Durometer Ultimate Temperature Fabric Estimated Weight Oil
Class Polymer Thickness Width Tensile*
Hardness* inches inches min. psi Elongation* Range Weight Per Linear Foot Resistance
Shore A ± 5 min. % per sq yd (1/8” x 36”)
50 1/16
1 SBR 36, 48 1500 250 -40ºF to +200ºF 10.8 oz 2.23 lb n/a
050A0425 thru 1/4
60 1/16
2 Neoprene 36, 48 1500 250 -40ºF to +220ºF 10.8 oz 2.73 lb Medium
060E1395 thru 1/4
50 1/16
3 SBR 36, 48 1500 250 -40ºF to +200ºF 10.8 oz 2.23 lb n/a
050A0425 thru 1/4
50 1/16
4 Nitrile 36, 48 1500 250 -40ºF to +250ºF 10.8 oz 2.40 lb High
050P1016 thru 1/4
General Purpose Grade TPE - Black A family of both soft and hard, black, versatile
thermoplastic. This material combines good
physical properties and chemical resistance for use in a wide range of applications. Specified for its performance properties
in a variety of industries: major appliances, caster wheels, mass transit, safety & protection, marine and industrial machinery.
Finish: Smooth Color: Black Trim: Trimmed Minimum: Please call for quote
Durometer Ultimate Estimated Weight
Durometer Thickness Width Tensile* Elongation* Temperature
Hardness Per Foot Specifications
Type inches inches psi Range
Shore ± 5 % (1/8” x 24”)
55 A 0.02 thru 0.25 24 640 330 –50ºF to +275ºF 1.27 lb MSAR20A
1 0 1 M0 0 5 5
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 28
General Purpose Grade TPE - Neutral Aversatile
family of soft, as well as hard, colorable,
thermoplastic. This material
combines good physical properties and chemical resistance for use in a wide range of applications.
Finish: Smooth Color: Neutral Trim: Trimmed Minimum: Please call for quote
Durometer Ultimate Estimated Weight Specifications
Durometer Thickness Width Tensile* Temperature DaimlerChrysler,
Hardness Type inches inches psi Elongation* Range Per Foot Ford Worldwide,
Shore ± 5 % (1/8” x 24”)
General Motors
MSAR20B,
64 A 0.02 thru 0.25 24 1000 440 –50ºF to +275ºF 1.27 lb WSD-M2D379-A1,
201M 0064
GMP.E/P.002
MSAR20C,
73 A 0.02 thru 0.25 24 1200 375 –50ºF to +275ºF 1.27 lb WSD-M2D380-A1,
201M 0073
GMP.E/P.003
MSAR20D,
80 A 0.02 thru 0.25 24 1600 450 –50ºF to +275ºF 1.27 lb WSD-M2D381-A1,
201M 0080
GMP.E/P.004
MSAR20E,
87 A 0.02 thru 0.25 24 2300 550 –50ºF to +275ºF 1.27 lb WSD-M2D382-A1,
201M 0087
GMP.E/P.005
MSAR30A,
40 D 0.02 thru 0.25 24 2750 600 –50ºF to +275ºF 1.27 lb WSD-M2D441-A,
203M 0040
GMP.E/P.006
MSAR30B,
50 D 0.02 thru 0.25 24 4000 600 –50ºF to +275ºF 1.27 lb WSD-M2D712-A1,
203M 0050
GMP.E/P.007
*Typical Values
NSF 51 & NSF 61 Approved Grade TPE Complies with NSF 61 for plumbing
applications in contact with potable
water and NSF 51 for food processing equipment. Complies with FDA regulations for rubber articles intended for repeated
use, as well as those in contact with non-fatty, non-oily foods as closures and sealing gaskets.
Finish: Smooth Color: Neutral Trim: Trimmed Minimum: Please call for quote
Durometer Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile* Specifications
Hardness Type inches inches psi Elongation* Range Per Foot
Shore ± 5 % (1/8” x 24”)
*Typical Values
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 29
Flame Retardant Grade TPE Aresistance
hard, colorable, flame retardant material. It exhibits good fluid
and contains non-ether brominated flame retardants
(non-furan emitting). It does not contain added antioxidants or metal deactivators.
Finish: Smooth Color: Neutral Trim: Trimmed Minimum: Please call for quote
Durometer Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile* Specifications
Hardness Type inches inches psi Elongation* Range Per Foot
Shore ± 5 % (1/8” x 24”)
*Typical Values
FDA Approved Grade TPE - Black TPEs (thermoplastic elastomers) have the
properties and performance of rubber, but are
processed like plastic. It has excellent clarity & superior colorability, and very good heat resistance. It was designed for
applications where FDA compliance, clarity & enhanced heat resistance are required. Safe to use for repeated food exposure.
Finish: Smooth Color: Black Trim: Trimmed Minimum: Please call for quote
Durometer Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile* Features
Hardness Type inches inches psi Elongation* Range Per Foot
Shore ± 5 % (1/8” x 24”)
*Typical Values
FDA Approved Grade TPE - Neutral TPEs (thermoplastic elastomers) have the
properties and performance of rubber, but are
processed like plastic. It has excellent clarity & superior colorability, and very good heat resistance. It was designed for
applications where FDA compliance, clarity & enhanced heat resistance are required. Safe to use for repeated food exposure.
Finish: Smooth Color: Neutral Trim: Trimmed Minimum: Please call for quote
Durometer Durometer Ultimate Temperature Estimated Weight
Thickness Width Tensile* Specifications
Hardness Type Inches Inches psi Elongation* Range Per Foot
Shore ± 5 % (1/8” x 24”)
*Typical Values
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 30
Corrugated Matting
Most widely used where floor protection and safety are vitally important.
Applications include general use in industry, home and office for heavy traffic
areas, aisles, hard floor surfaces or as anti-fatigue matting. Use thicker matting
for extra heavy duty service. Product strengths include extended wear,
all-weather, strong sound absorption characteristics, cleanability and wear
resistance. Will not curl, shrink, or separate. This product can be easily beveled
and perforated for entry mat use.
Finish: Corrugated Texture Color: Black Trim: Trimmed Non-Stock Minimum: Please call for quote
Approximate Approximate Weight Surface
Color Thickness Width Specifications
inches inches Roll Length Per Foot Texture
(12” x 36”)
Half = 75 feet
Black 1/8 24, 36, 48, 72 2.1 lb Corrugated ASTM D 2000 1AA 706
Full = 150 feet
Black 3/16 36, 48, 72 75 feet 3.7 lb Corrugated ASTM D 2000 1AA 706
75 feet
Black 1/4 24, 36, 48, 72 5 lb Corrugated ASTM D 2000 1AA 706
72” = 36 feet
ASTM D 178-93
Black 1/4 24, 36, 48 75 feet 5 lb* Corrugated
Type 1 Class 2
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 31
KleenRite® Matting
KleenRite® matting is ideally suited for tool box lining, utility vehicles,
step stools and a myriad of other applications.
Finish: KleenRite Texture Color: Black Trim: Trimmed
Approximate Approximate Weight Surface
Color Thickness Width Specifications
inches inches Roll Length Per Foot Texture
(12” x 36”)
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 32
60 Durometer Neoprene Tubing
WARCO BILTRITE’s 60 Durometer Neoprene Tubing is Anti-Fungal per Mil-Std-8.10 and is designed to meet the Mil-R-6855
Class 2 specification. Compression Set = 50% max. Material is supplied unmarked. For markings, please contact us.
Color: Black Stock-Item Purchase Minimum: 10 Feet Non-Stock Purchase Minimum: Please call for quote
Durometer Inner Diameter Wall Thickness Ultimate Temperature
Tensile Specifications
Hardness Range Range min. psi Elongation Range
Shore A ± 5 inches inches min. %
1/4” $0.75
Inne r D i am e te r (in c h e s )
(± 0.010) 31265091
1/2” $1.28
1/4” ID 1/2” ID 9/16” ID 5/8” ID 3/4” ID (± 0.016) 31265092
(± 0.010) (± 0.016) (± 0.017) (± 0.018) (± 0.021) 9/16” $1.45
1/16” Wall 1/16” Wall 1/16” Wall 1/16” Wall 1/16” Wall (± 0.017) 31265093
(± 0.009) (± 0.009) (± 0.009) (± 0.009) (± 0.009) 5/8” $1.63
(± 0.018) 31265094
3/4” $2.16
Other dimensions, profiles and polymers are available, (± 0.021) 31265095
please call us at 714-532-3355 for pricing and availability Prices are per foot ($/ft).
= Regularly Stocked Items.
Mil-R-6855 Class 2
60 1/16 thru 5 1/32 thru 1 1500 300 –50ºF to +220ºF Type A/B Grade 60
Catalog Pricing is available on the following pages for the Wall Thicknesses below:
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 33
Utility Tarp Straps
Single piece molded construction ensures exceptional strength and stretch resiliency. The special EPDM compound used
in the construction of WARCO BILTRITE Utility Straps is suited for high oxidation and weather resistance without cracking.
An assortment of lengths including 6 in, 10 in, 15 in, 15 in, 21 in, 31 in are available.
Rubber Waterstop has been used extensively on projects throughout the United
Rubber Waterstop States and the world. Beginning with projects designed to meet the U.S. Army
Corps. of Engineers’ and the U.S. Bureau of Reclamation’s specifications, Rubber
Waterstop usage has expanded to all types of concrete structures for the purpose of keeping liquids in or out. SBR Rubber
is used primarily for water containment, while Neoprene Rubber is used generally for projects involving sewage, water
treatment, and chemical environments. Waterstops are also available in other polymers such as EPDM, Nitrile, Silicone, and
Natural Rubber. WARCO BILTRITE maintain Waterstop compounds that meet the U.S. Army Corps of Engineers’
CRD-C-513-71 specification and Caltrans 51-2.04 specification. Other compounds can be provided to meet other national
and international specifications in accordance with project requirements. Non-specification commercial grade Rubber
Waterstop is also available. Please contact us for details.
55 1/8 thru 1/2 36, 48 2000 300 –40ºF to +220ºF 2.56 lb Caltrans 51-2.04
055E0507 Waterstops
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 34
Waterstop Extruded Profile Chart
The profiles below are normally provided in SBR and Neoprene compounds as required. Waterstop is usually provided in 50 ft.
lengths, but can be manufactured in longer and shorter lengths to minimize field splicing. Special profiles and compounds can be
provided to meet specific project requirements. WARCO BILTRITE Rubber Waterstop is also available in non-spec commercial grade.
TYPE
6“ 9“ 6“ 9“
Custom widths and thicknesses are available - please call for a quote. Prices are subject to change without notice. Price list effective February 1, 2014.
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 35
Notes
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 36
Index
TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 AASHTO Bearing Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
AASHTO Unsupported Neoprene
GENERAL PRODUCTION INFORMATION . . . . . . . . . . . . . . 3
Bearing Pads - Style 71 . . . . . . . . . . . . . . . . . . . . . . . . . 21
SPECIFICATION INDEX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 AASHTO Unsupported Natural Rubber
Bearing Pads - Style 72 . . . . . . . . . . . . . . . . . . . . . . . . . 22
BUY THE FOOT PARTS INDEX
.............................6
AASHTO Unsupported Calendered Neoprene
Neoprene Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Bearing Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Commercial Neoprene - Style 10 . . . . . . . . . . . . . . . . . . . . 8 AASHTO Unsupported Molded Neoprene
Matte Finish Neoprene - Style 12 . . . . . . . . . . . . . . . . . . . . 8 Bearing Pads . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Mid-Grade Neoprene - 5100 Series . . . . . . . . . . . . . . . . . . 9
Viton® & Fluoroelastomer Sheet . . . . . . . . . . . . . . . . . . . 23
Premium Neoprene (100% Neoprene) . . . . . . . . . . . . . . . 9
100% FKM Commercial Fluoroelastomer:
FDA Neoprene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
66% Fluorine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Neoprene Performance Molded Sheets . . . . . . . . . . . . . . 10
Commercial Viton® A: 66% Fluorine. . . . . . . . . . . . . . . . . 23
ASTM D 2000 M2BC (Neoprene) . . . . . . . . . . . . . . . . . . . 10
Commercial Viton® A: 66% Fluorine (Brown) . . . . . . . . . . 23
MIL-R-6855 Class 2 (A&B) - Oil Resistant Neoprene . . . . . 10
Premium Viton® A: 66% Fluorine . . . . . . . . . . . . . . . . . . . 23
MIL-R-3065 SC (Neoprene) . . . . . . . . . . . . . . . . . . . . . . . . 11
Premium Viton® B: 68% Fluorine . . . . . . . . . . . . . . . . . . . 24
Aerospace Material Specification (Neoprene/Nitrile) . . . 11
FDA Viton® A: 66% Fluorine . . . . . . . . . . . . . . . . . . . . . . . 24
Anti-Microbial Neoprene . . . . . . . . . . . . . . . . . . . . . . . . . 11
Military Specification Grade Viton® A: 66% Fluorine . . . . 24
Low Smoke, Low Flame, Low Toxicity Neoprene . . . . . . . 12
Silicone Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Nitrile (Buna-N) Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
COMSIL®: Commercial SIlicone. . . . . . . . . . . . . . . . . . . . . 25
Commercial Nitrile - Style 35 . . . . . . . . . . . . . . . . . . . . . . 13
Specification Grade SIlicone . . . . . . . . . . . . . . . . . . . . . . 25
Premium Nitrile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
FDA Silicone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
FDA Nitrile - Style 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
WARCO White® FDA Nitrile . . . . . . . . . . . . . . . . . . . . . . . 14 Butyl Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MIL-R-6855 Class 1 (Fuel Resistant Nitrile) . . . . . . . . . . . . 14
Cloth-Inserted (CI) Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . 26
MIL-R-3065 SB (Nitrile) . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cloth-Inserted Neoprene - Regular Cotton Ply . . . . . . . . 26
ASTM D 2000 M5BG (Nitrile) . . . . . . . . . . . . . . . . . . . . . . 15
Cloth-Inserted Neoprene - Regular Polyester Ply . . . . . . 26
MIL-G-1149 (Neoprene/SBR/Nitrile). . . . . . . . . . . . . . . . . 15
Cloth-Inserted SBR - Regular Cotton Ply . . . . . . . . . . . . . 27
MIL-R-2765 (Nitrile) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cloth-Inserted SBR - Regular Polyester Ply . . . . . . . . . . . 27
Transformer Oil Material . . . . . . . . . . . . . . . . . . . . . . . . . 15
Cloth-Inserted SBR - Reduced Cotton Ply . . . . . . . . . . . . 27
Bio-Diesel Nitrile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cloth-Inserted SBR - Reduced Polyester Ply. . . . . . . . . . . 27
SBR Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 HHP-151F Cloth-Inserted Sheet . . . . . . . . . . . . . . . . . . . . 28
Red Rubber SBR - Style 20 . . . . . . . . . . . . . . . . . . . . . . . . 16
Thermoplastic Elastomer Sheet . . . . . . . . . . . . . . . . . . . . 28
Specification Grade SBR . . . . . . . . . . . . . . . . . . . . . . . . . . 16
General Purpose Grade TPE - Black . . . . . . . . . . . . . . . . . 28
Premium SBR - Style 22 . . . . . . . . . . . . . . . . . . . . . . . . . . 16
General Purpose Grade TPE - Neutral . . . . . . . . . . . . . . . 29
Natural Rubber Sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 NSF 61 Approved Grade TPE . . . . . . . . . . . . . . . . . . . . . . 29
Natural Rubber - Style 28 . . . . . . . . . . . . . . . . . . . . . . . . . 17 Flame Retardant Grade TPE . . . . . . . . . . . . . . . . . . . . . . . 30
Black Natural Rubber . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 FDA Approved Grade TPE (Black) . . . . . . . . . . . . . . . . . . . 30
Pure Gum Floating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 FDA Approved Grade TPE (Neutral) . . . . . . . . . . . . . . . . . 30
EZ Cut Non-Floating Gum . . . . . . . . . . . . . . . . . . . . . . . . 18
Rubber Mats & Matting . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Protein Free (Synthetic Polyisoprene) . . . . . . . . . . . . . . . 18
Corrugated Matting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Tuff-Stuff® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ASTM Switchboard Type 1 Matting . . . . . . . . . . . . . . . . . 31
EPDM Sheet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 KleenRite® Matting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Commercial EPDM - Style 40 . . . . . . . . . . . . . . . . . . . . . . 18 FingerTrac® Entrance Mats . . . . . . . . . . . . . . . . . . . . . . . . 32
Premium EPDM - Style 45. . . . . . . . . . . . . . . . . . . . . . . . . 19 Tredair® Comfort Mats . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Premium EPDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Rubber Extrusions
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Peroxide Cure EPDM . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
60 Durometer Neoprene Tubing . . . . . . . . . . . . . . . . . . . 33
MIL-R-21252 (EPDM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Neoprene Cable Jacket Tubing to MIL-R-6855 . . . . . . . . 33
MIL-R-83285 GR80 (EPDM) . . . . . . . . . . . . . . . . . . . . . . . . 20
MIL-R-900 (EPDM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Utility Tarp Straps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ASTM D 2000 M4AA (EPDM) . . . . . . . . . . . . . . . . . . . . . . 21
Rubber Waterstop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Skirtboard & Chute Lining . . . . . . . . . . . . . . . . . . . . . . . . 21
TERMS AND CONDITIONS OF SALE . . . . . . . . . . . . . . . . . 38
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 37
STANDARD TERMS AND CONDITIONS OF SALE
Industrial Rubber Products
WARCO BILTRITE products are sold commercially for multiple applications as determined 9. LIMITATION OF LIABILITY: Seller shall not be liable in contract, in tort (including
by the end-user. Information on certain physical properties of our various styles and grades negligence),or otherwise for damage or loss of other property, loss of profits or revenue,
is provided in our product literature, but such information is unrelated to any particular use loss of use of property or equipment, claims of customers of the Buyer, or for any special,
or application. Determination of the suitability of the goods for the uses and applications indirect, incidental, or consequential damages whatsoever. Under no circumstances shall
contemplated by Buyer and others shall be the sole responsibility of the Buyer or user. Seller’s liability exceed the purchase price of the goods in respect of which damages are
Consultation with qualified engineers and testing laboratories is recommended. WARCO claimed.
BILTRITE does not recommend any of its products for any particular use or application. The
purchaser or user shall assume full responsibility for the adequacy and suitability for the 10. PRODUCTS SUITABILITY AND LENGTH OF SERVICE: Determination of the
intended use. Rubber products may fail as a result of temperature variances, excessive suitability of the goods for the uses and applications contemplated by Buyer and others
pressures, abrasion or damaging substances. The wear life of rubber products is limited by shall be the sole responsibility of the Buyer or user. No guaranty is given with respect to
the circumstances and conditions of use. Rubber materials should be inspected regularly length of service on any particular application. Suggestions or recommendations made by
and should be replaced as appropriate for operational and safety requirements and the Seller in its product literature concerning uses or applications of the goods are believed to
prevention of injury or damage to persons and property. be reliable, but Seller makes no warranty or guaranty of results to be obtained since the
conditions of the use and application by Buyer and others are beyond Seller’s control.
Our rubber products, except where indicated, are a proprietary blend of various polymers
formulated to meet stated physicals and specifications. The named polymer is not 11. FORCE MAJEURE: Seller shall not be liable for failure to perform or for delay in
necessarily the polymer representing the highest percentage of the polymer blend. The performance due to fire, flood, strike or other labor difficulty (Seller shall not be required to
various specification call outs are a valuable guide in selecting the type and grade of sheet settle any labor matter against its own best judgment), act of God, act of any government
rubber for a particular application. In any application, the customer should evaluate the authority, acts or omissions of the Buyer, riot, embargo, explosion, accident, breakdown of
performance requirements and conditions that will affect the working life of the rubber machinery or equipment, shortage of or inability to obtain fuel, power, raw materials,
product. Field testing may need to be performed before the type of sheet rubber is equipment, transportation of the product at usual prices or usual sources, or due to any
selected. If the customer’s quality assurance incorporates the testing of rubber material, other cause beyond its reasonable control. Quantities so affected by such circumstances
the test criteria should include the physical property call outs of the specifications that are may be eliminated without liability, but this Agreement shall otherwise remain unaffected.
most critical to its application. Polymer type alone may not be adequate for the 12. RETURNED GOODS: No goods may be returned without Seller’s prior written
selecting of the rubber that is best suited for a specific application. authorization. Each request for exchange or return shall describe the condition of the goods
ASTM basic requirements for physical properties are based on values obtained from and the reasons for the requested return or exchange. If the Seller agrees to accept a return
standard laboratory test specimens prepared and tested in accordance with the applicable or exchange, the Buyer shall pay return transportation cost and a restocking charge; the
ASTM test methods. Test results from specimens prepared from finished products may not restocking charge will be determined based upon the Seller’s ability to resell the exchanged
duplicate values obtained from standard test specimens. Per ASTM D2000, Section 7.1, or returned material and the reason for the return.
Buyer agrees that when standard test specimens are cut from finished parts in accordance 13. QUANTITY VARIANCE: Due to manufacturing variances, the quantity of goods
with Practice D 3183, a deviation to the extent of 10% on tensile strength and elongation delivered will be within 10%, more or less, of the quantity specified and shall be charged at
values is permissible. the unit price herein.
1. PAYMENTS: Seller may require full or partial payment in advance at any time if in its sole 14. ENTIRE AGREEMENT: This Agreement constitutes the complete and final Agreement
judgment, the financial condition of the Buyer does not justify the terms of payment of sale and purchase of the goods specified herein and supersedes all prior contracts and
specified herein. A charge of 1-1/2 percent (1-1/2%) per month (or at the highest rate discussions. No modification hereof shall be effected by the use of purchase order,
permitted by law) shall be payable on all overdue accounts. Orders will not be processed acknowledgment, acceptance, or other forms at variance with or in addition to the terms
until payment terms are approved by Seller’s Credit Department. and conditions contained herein. No modification shall be effected in any manner other than
2. PRICES SUBJECT TO CHANGE: Seller may change any price, shipment or freight term in writing and signed by the party claimed to be bound thereby.
in effect at any time and from time to time by giving Buyer at least fifteen (15) days written 15. GOVERNING LAW: This contract shall be governed by and construed under the laws
notice thereof. Buyer’s failure to give Seller a written objection to any such change within of the State of California.
ten (10) days after receipt of notice shall constitute acceptance of such change. Where 16. TRANSPORTATION POLICY: All deliveries will be made F.O.B. Point of Shipment,
objection is made, Seller shall advise Buyer within ten (10) days thereafter whether Seller freight calculated and billed when releases for shipment are below the stated freight
will (a) continue to deliver at the price or on the terms in effect prior to the announced allowances for the product ordered, released and shipped. For specific freight allowances
change, or (b) cancel this contract. Any cancellation shall be effective upon Buyer’s receipt please refer to catalog sections for products ordered. Freight prepaid and allowed by most
of Seller’s notice and shall be without further obligation of either party to the other except to economical routing on shipments weighing 3,000 lbs or more to one destination, from one
perform or pay all obligations accrued through date of cancellation. Provided however, that location, one shipment, one purchase order, within the continental United States. Applicable
in the case of non-stock items ordered specifically for Buyer’s use, Seller reserves the right surcharges and/or accessorial charges are not covered and will be billed accordingly.
to increase prices to cover the increases in its costs arising from increases in the cost of Freight allowance applies to roll goods of WARCO calendered Sheet products and Biltrite
materials or labor rates which become effective between the date of this acknowledgment Sheet & Matting products only. Does not apply to "Buy the Foot" items or extruded, molded,
and the date of shipment. In such event, this Agreement shall remain in effect at the price and spliced products. Orders including both stock and made-to-order items will not be
adjusted to reflect said increases. combined for weight unless the stock items are stocked at the manufacturing plant
3. MINIMUM PURCHASE: Stock sheet Item = One roll minimum. producing the made-to-order items and the customer is willing to wait for shipment at one
Non-stock sheet and Custom items = Please request quote. time to one destination. All price page and catalog weights are approximate and actual
4. TAXES: Buyer shall reimburse Seller for all taxes, excises or other charges which Seller shipping weights may vary from these listings. In case of dispute, actual shipping weights
may be required to pay to any governmental entity (national, state or local) upon the sales, will apply. Origin, Method of Shipping and Routing: Seller will determine the point of
production or transportation of the goods sold hereunder. origin of shipment, the method of transportation and the routing of shipment. Purchasers
requiring shipment by a method or routing other than that will be billed any excess or
5. DELIVERY: Unless otherwise specified herein, goods will be delivered F.O.B. point of premium in transportation charges. If Seller elects to ship by other than common carrier,
shipment, freight allowed on specified pounds. Seller will determine the point of origin of the full transportation charges will be prepaid and any freight charges billable (under
shipment, the method of transportation, and the routing of shipment. Partial deliveries shall allowances) will be calculated and billed. Purchaser Pick Up: No allowance will be made
be accepted by the Buyer and paid for at the prices and terms hereunder. Seller does not in lieu of transportation if the buyer accepts shipment at the factory or the warehouse or
guarantee any delivery or completion date. In the event of delay in delivery of goods, Seller freight station. Transportation charges will not be deducted from the selling price.
shall not be liable or responsible for any loss, damage, expense or charge of any kind,
direct or indirect, suffered or incurred by Buyer as a result of such delay. 17. CONCEALED DAMAGE: Seller will not participate in any settlement of claims for
concealed damage. Upon receipt of any shipment, Buyer must unpack immediately and, if
6. TITLE AND RISK OF LOSS: Title and risk of loss in the goods shall pass to Buyer upon damage is discovered, must:
Seller’s delivery to carrier at the shipping point, notwithstanding the terms of shipment • Not move the product from the point of examination
specified herein. • Retain shipping container and packing material
7. WARRANTIES AND DISCLAIMERS: Goods furnished under this Agreement shall • Notify the carrier’s agent to make an inspection and confirm in writing
conform to the description herein. All first quality goods are warranted to be free from • Send Seller a copy of the carrier’s inspection report
defects in material and workmanship at the time of shipment. Seller shall convey good title • Make a claim for damage with the carrier
to buyer. Seller further warrants that the goods sold hereunder do not infringe any valid • Recovery for any damage to merchandise incurred during shipping shall be the sole
United States patent, but Seller does not warrant, however, that the use of the goods or responsibility of Buyer. Any such damage shall not defeat or otherwise affect the
products made therefrom, either alone or in conjunction with other materials, will not obligation of Buyer to pay all amounts due Seller with respect to the damaged goods.
infringe any valid United States patent. THE WARRANTIES SET FORTH IN THIS 18. CANCELLATION: Requests for cancellation or modification of orders must be
PROVISION ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES submitted in writing and received by Seller at least 2 days prior to shipment. Any
EXPRESSED OR IMPLIED, INCLUDING WARRANTIES ARISING FROM COURSE OF cancellation or modification will be effective only when acknowledged in writing by Seller
DEALING OR USAGE OF TRADE. SELLER MAKES NO WARRANTY, EXPRESSED OR and can be made subject to status of production of goods. Orders for merchandise
IMPLIED, OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. produced specifically for a customer cannot be canceled once goods are produced.
ALL PRODUCTS ARE SOLD AND WARRANTED ONLY PURSUANT TO OUR
PUBLISHED TERMS AND CONDITIONS OF SALE. WE ARE NOT RESPONSIBLE TO 19. ACCEPTANCE OF ORDERS: Issuance of any Catalog or Price List does not constitute
THE USER FOR ANY CONSEQUENTIAL, INCIDENTAL, OR SPECIAL DAMAGES an offer for the sale of any products described therein. All orders are subject to the
RESULTING FROM PRODUCT USE OR PROCESSING. acceptance of Seller. All orders accepted by Seller are accepted on the understanding that
Buyer, by placing the order, has agreed to these Standard Terms & Conditions of Sale and
8. CLAIM PERIOD AND REMEDIES: Prompt written notice shall be given to Seller of any that they are therefore part of the Buyer's order.
claim of failure of goods to conform to the warranties hereunder. Should any failure to
conform to these warranties appear under normal and proper use within the period of one 20. ATTORNEYS’ FEES AND VENUE: In any action to collect amounts due Seller with
(1) year from the date of shipment to the Buyer, Seller shall correct such nonconformity, at respect to sales made to Buyer, arising out of or relating to this Agreement or any such
its option, by repair or replacement of the defective goods, or by the refund of the purchase sales, or in which a party seeks an interpretation of this Agreement or asserts it as a
price thereof with due allowance made for the service rendered by the goods returned. In defense, the prevailing party shall be entitled to recover attorneys’ fees in an amount
no event shall Buyer commence any action under this Agreement later than one year after determined by the Court to be reasonable, as well as such party’s costs of suit. All notices,
receipt of the goods. The remedies provided above are the Buyer’s sole remedies for any requests, claims and other communications by Buyer with respect to this Agreement or
failure of Seller to comply with its obligations. Correction of any non-conformity by repair or sales hereunder shall be directed to Seller at its executive offices at 1337 Braden Court,
replacement or by refund of the purchase price of the nonconforming goods (less allowance Orange, California 92868 (714) 532-3355. Any action brought by Buyer against Seller must
for use) shall constitute fulfillment of all obligations of Seller with respect thereto, whether be brought in a state or federal court located in Orange County, California, and any action
the claims of Buyer are based in contract, or tort (including negligence), or otherwise. brought in any other location shall, upon appropriate motion by Seller, be dismissed.
TERMS AND CONDITIONS OF SALE ARE SUBJECT TO CHANGE WITHOUT NOTICE. VISIT WWW.WARCO.COM/TERMS FOR THE MOST CURRENT TERMS AND CONDITIONS.
WEST AMERICAN RUBBER COMPANY, LLC | 1337 BRADEN COURT, ORANGE, CALIFORNIA 92868 | TEL: 714-532-3355 | sales@warco.com
BILTRITE RIPLEY OPERATIONS, LLC | 16310 HIGHWAY 15 NORTH, RIPLEY, MISSISSIPPI 38663 | TEL: 800-245-8748 | biltritesales@warco.com
Tel: 714-532-3355
Contact Customer Service
Toll-Free: 800-245-8748 Email: sales@warco.com 38
For more information
please visit us at warco.com
Corporate Office
1337 Braden Court
Orange, California 92868
Tel: 714-532-3355
Fax: 714-532-2238