Beruflich Dokumente
Kultur Dokumente
your assembly
challenges. 289
5,000+
Do it your way.
adhesive and tape SKUs
88,667
convenience and ease of use.
employees
Do it together.
• No matter what you need to bond, you can count on 3M’s
expertise, technologies and 88,667 dedicated employees to
help you find solutions.
• From wood, metal, foil, insulation, foam, fabric and panel
lamination to specialty high performance and multipurpose
materials of every kind, solutions are one call away.
Finding your
3M Adhesive
& Tape
Assembly Solutions
100,000 patents
1
Do it boldly.
• 3M has been a world leader in bonding technology
for decades and we have the patents to prove it.
chance to do it right
Do it responsibly.
• Sustainability is a natural extension of 3M’s corporate values.
• We developed the first water-based contact adhesive
ever — more than 40 years ago.
• We have a wide selection of Low VOC products that help
contribute to LEED® credits and are GREENGUARD™ Certified.
290
3M™ Adhesives and Tapes
for design, assembly and production.
Table of Contents
Bonding Tapes
3M™ VHB™ Tapes and Primers................................................................ 68–75
3M™ Extreme Sealing Tapes........................................................................... 76
3M™ Double Coated Foam Tapes........................................................... 77–78
8 3M™ Double Coated Tapes...................................................................... 79–81
3M™ Removable/Repositionable Tapes.......................................................82
3M™ Adhesive Transfer Tapes................................................................ 83–87
Scotch® ATG Adhesive Transfer Tapes.........................................................88
3M™ Extended Liner Tapes.............................................................................89
Specialty Technologies
3M™ Dual Lock™ Reclosable Fasteners................................................ 92–93
3M™ Hook and Loop Reclosable Fasteners......................................... 94–95
3M™ Single Coated Foam Tapes....................................................................96
3M™ Converter Markets Center.................................................................... 97
and adhesive technologies require With uniform stress distribution of adhesives and tapes, lighter, thinner materials can be used
little operator training. without concerns about distortion, splitting, or crazing at the mechanically fastened site.
Elimination of holes in metal also reduces the chances for rust and corrosion.
14
11
M™ Extreme
3 3M™ Scotch-Weld™
Sealing Tapes PUR Adhesives
M™ Adhesive
3 16
21
Sealants
M™ Hot Melt
3 M™ Scotch-Weld™
3
Adhesives Retaining Compound
12
22
17
A
Assembly
What type of assembly is required? (Refer to 7
common assembly types in the right hand column.) Panel to Frame/
Stiffener to Panel
What are the overall performance needs of the pg 4
assembly (flexibility, high peel strength, etc.)?
292
Small Joint
Substrate
S
Assembly
What are the materials that are being bonded pg 6
together? (Refer to the substrate selectors for 292
each assembly type on pages 4–15.)
Consider the surface condition texture of
each material.
Large Surface
Lamination
Process
pg 8
What is the current assembly and manufacturing 292
process?
P
Does the solution need to fit into the current process/
equipment or can the process/equipment change?
What are the various process steps and how Mounting and
quickly will the assembly be moved to each step? Trim Attachment
pg 10
At any time, might the assembly bond need to be
292
repositioned? If so, why and when?
Are there any environmental, regulatory or
workplace safety restrictions?
E
Gasket Attachment
End-Use
pg 12
How and where is the final product used?
292
Will the assembly be exposed to harsh
environmental conditions (UV, chemicals, high
humidity, very high or low temperatures, etc.)?
Sealing
pg 14
C
292
Cost
Where can improvements be made in the
assembly process (labor, reduction of
process steps, materials, workflow, etc.)? Potting and
Encapsulating
291
pg 14
292
Panel to Frame: Decorative or load bearing panel that is applied Possible Adhesive or Tape Requirements:
to a rigid frame or support. Examples include trailer panels, • Dead load holding strength
elevator walls and sign boxes.
• Flexibility for dynamic loads and thermal
Stiffener to Panel: Stiffeners are applied to panels to give extra expansion mismatch
support and rigidity. Examples include trailer wall panels, traffic
• Fill a gap or variation in fit from end to end
signs and large metal enclosures.
• Provide a water seal
3M™ Scotch-Weld™
Attribute 3M™ VHB™ Tapes Structural Adhesives 3M™ Adhesive Sealants 3M™ Reclosable Fasteners
Number of Steps to Apply and
Ease of Application
Holding Power
Assembly Solutions
(Aluminum, Steel, Stainless, Galvanized) Painted Metal, Composite Panel) Glass (ABS, Acrylic, Polycarbonate, Nylon) (Polypropylene, Polyethylene)
4941,
RP45, 5952 *4941,
*RP45, 5952 *4941,
*RP45, *5952 *4941,
*RP45, 5952 *4941,
*RP45, *5952
LSB60NS LSB60NS
LSB60NS
LSB60NS
DP8010 Blue
Metals
*550FC + AC61 *550FC + AC61 *590, *560, *760 *560, *760 *560, *760
SJ3550/51/52,
SJ3540/41/42,
SJ3560/61/62,
SJ3550/51/52,
SJ3540/41/42,
SJ3571/72 SJ3526N/27N SJ3571/72 SJ3571/72 SJ3526N/27N
*4941,
*RP45, 5952 *4941, *RP45, *5952
*4941, *RP45, 5952 *4941, *RP45, *5952
DP8810NS
LSB60NS
DP8810NS DP8010 Blue
Paints
*550, *560, *760 *590, *560, *760 *560, *760 *560, *760
*4941,
*RP45, *5952 *4941,
*RP45, 5952 *4941,
*RP45, *5952
DP460 DP100 Plus Clear
DP8010 Blue
Glass *590 *560, *760 *560, *760
Key
3M™ VHB™ Tapes *4941,
*RP45, 5952 *4941,
*RP45, *5952
3M™ Scotch-Weld™ Structural Adhesives
Plastics: LSE
*560, *760
26
27 28 29
29
This guide lists products that are commonly used for this specific application. It is important that the customer evaluates these suggested products in their specific application.
Small Joint: Small joints are typically irregularly shaped but only a few Possible Adhesive or
inches of overlap area. They may be insertion joints or overlap joints, Tape Requirements:
or some combination. Examples include sporting goods (e.g., golf • Low viscosity for tight fitting parts
club heads to shaft), plastic casings, lens mounting for instrumentation,
• Vibration resistance
mortise and tenon furniture joints, thread locking or shaft retailing,
magnet bonding and jewelry making. • Very high strength
• Bond dissimilar materials
3M™ Scotch-Weld™ 3M™ Scotch-Weld™ 3M™ Hot Melt 3M™ Scotch-Weld™ 3M™ Scotch-Weld™
Attribute Structural Adhesives Instant Adhesives Adhesives PUR Adhesives Threadlockers
Temperature and
Solvent Resistance
Aesthetics
Rework
Assembly Solutions
Metal Metal (ABS, Acrylic, (Polypropylene,
(Unpainted) (Painted) Glass, Ceramic, Stones Rubber, Elastomers Polycarbonate, Nylon) Polyethylene) Wood
DP420NS
DP8805NS
DP420NS
2216
DP8805NS
DP8010 Blue
DP100 Plus
Metal (Unpainted)
3747, 3789 3747, 3764 3747, 3789 3764, 3747 3748, 3764 3792
RT09
TE040,
TE040, EZ25150
EZ250150 EZ250150
TL62
DP8805NS
DP100 Plus
DP620NS
DP8805NS
DP8010 Blue
DP620NS
PR100 PR100 *PR100 PR100 *PR100 SI100
Metal (Painted)
3747, 3764 3764, 3792 3748, 3764 3748, 3764 3764, 3792
TE040,
TE040, EZ25150
EZ250150 EZ250150
DP100 Plus
DP100 Plus
DP100 Plus
DP8010 Blue
DP420NS
Glass, Ceramic, Stones
*PR100
DP620NS *PR100
DP604NS
Rubber, Elastomers
*PR100 *SI100
Key
3M™ Scotch-Weld™ Structural Adhesives
3M™ Scotch-Weld™ Instant Adhesives
DP8405NS,
DP8010 Blue
DP620NS
3M™ Hot Melt Adhesives DP8805NS
Plastics: HSE, MSE
DP100
SI100
Wood
3792
EZ250120,
EZ250060
30 31 32
This guide lists products that are commonly used for this specific application. It is important that the customer evaluates these suggested products in their specific application.
Large Surface Lamination: Two surfaces (substrates) of similar size, Possible Adhesive or Tape Requirements:
either rigid or flexible, are bonded or laminated together where a • Cover full surface
majority of the surface is covered by the adhesive or tape in order
• Flexible when dry; not stiff
to create the bond. Examples include high pressure laminate
to tabletops, fabric to foam for furniture, veneers on wood • Allow for positioning parts
and flexible transportation flooring. • Bonds quickly/little or no fixturing
3M™ Scotch-Weld™ 3M™ Contact and 3M™ Hot Melt 3M™ Scotch-Weld™ 3M™ Adhesive
Attribute Structural Adhesives Spray Adhesives Adhesives PUR Adhesives Transfer Tapes
Temperature and
Solvent Resistance
Assembly Solutions
Metals, Paints, Glass (EPDM, Santoprene®) (Urethane, Fabrics) Plasticized Vinyl Polycarbonate, Nylon) Wood
6116 6116
950, F9465PC TS230, TS115
TS230, TS115 TS230,
950, 6035PC
TS115HGS
6035PC, 950
950, 6035PC
2216 2216 2216
Key
4491, 1300 4491, 1300 4491, 1000NF
Plasticized Vinyl
TS230, TS115
TS230,
9472LE, 468MP
TS115HGS
9472LE,
468MP
2216
94 CA, 30NF
6111/6111HT,
6116
Wood
TS230,
TS115HGS
6035PC,
468MP
33
35 34 36
This guide lists products that are commonly used for this specific application. It is important that the customer evaluates these suggested products in their specific application.
Mounting: Applying an object to a surface. Generally, static loads are Possible Adhesive or
prevalent and the mounted item is smaller than the surface to which it is Tape Requirements:
bonded. Examples include small signs, mirrors and white boards, • Dead load holding strength
and panel-over-panel with partial adhesive coverage.
• Aesthetics
Trim: Decoration or identification added to a surface. Examples include
• Removability
nameplates, edge banding, bezels, rosettes and muntin bars.
• Fast bonding/little or no fixturing
3M™ VHB™ 3M™ Scotch-Weld™ 3M™ Scotch-Weld™ 3M™ Hot Melt 3M™ Scotch-Weld™ 3M™ Reclosable 3M™ Adhesive 3M™ Double
Attribute Tapes Structural Adhesive Instant Adhesive Adhesives PUR Adhesives Fasteners Transfer Tapes Coated Tapes
Shear and Peel Strength
Temperature and
Solvent Resistance
Aesthetics
Repositionability
During Application
Rate of Strength Build
Assembly Solutions
Metals (Aluminum, Steel, Painted Metal, Composite Panel, (ABS, Acrylic, Plastics: LSE
Stainless, Galvanized) Sealed or Painted Wood) Glass Polycarbonate, Nylon) (Polypropylene, Polyethylene) Wood
4941, 5952, RP45 *4941, 5952, *RP45 * 4941, *5952, *4941, 5952, *RP45 *4941, *5952, *RP45 3792
DP8805NS DP8810NS *RP45 DP8805NS DP8010 Blue EZ250150
3789, 3747 3764, 3747 DP420NS 3764, 3747 3764, 3747
TE040, EZ250150 TE040, EZ250150 3789, 3747 TE040, EZ250150 SJ3540/41/42,
Metals
J3550/51/52,
S J3540/41/42,
S J3560/61/62,
S J3550/51/52,
S SJ3526N/27N
SJ3571/72 SJ3526N/27N SJ3571/72 SJ3571/72 9472LE, 9485PC
468MP, F9473PC 9472LE, 9485PC 468MP, F9473PC 468MP, 9472LE 9500PC
9500PC 9500PC 9500PC 9500PC
*4941, 5952, *RP45 *4941, *5952, *4941, 5952, *RP45 *4941, *5952, *RP45 3764,
DP8810NS *RP45 DP8410NS DP8010 Blue 3792
PR100 DP420NS PR100 *PR100 EZ25150
3764, 3792 3764, 3792 3747, 3792 3748, 3764
Paints
3748, 3764
SJ3540/41/42,
SJ3526N/27N
9472LE, 9485PC
9500PC
37
3792
Wood
EZ250120,
EZ250060
3
38 39
This guide lists products that are commonly used for this specific application. It is important that the customer evaluates these suggested products in their specific application.
Gasketing: Attachment of a substrate typically, foam, rubber or paper that Possible Adhesive or
acts as an interface or seal between two surfaces. 3M offers solutions for Tape Requirements:
attaching preformed gaskets, and also solutions which can replace gaskets or • Easy and fast to apply gaskets
bond and seal simultaneously. Examples include air and liquid filters, fluid
• Resist fluids
handling equipment, heat exchangers and ball joints.
• High adhesion to foams
and rubber
3M™ VHB™ 3M™ Scotch-Weld™ 3M™ Scotch-Weld™ 3M™ Contact and 3M™ Adhesive 3M™ Double
Attribute Tapes Instant Adhesives Gasket Makers Spray Adhesives Transfer Tapes Coated Tapes
High Strength and
Rubber Bonding
N/A N/A
Temperature and
Solvent Resistance
Ease of Application
Assembly Solutions
Rubber (EPDM, Santoprene®)
950
3M™ VHB™ Tape can replace gaskets on many substrates listed in the chart.
3M™ Scotch-Weld™ Gasket Makers are suitable to replace gaskets in metal to metal applications.
Key
3M™ Scotch-Weld™ Instant Adhesives
3M™ Scotch-Weld™ Gasket Makers
3M™ Contact and Spray Adhesives
3M™ Adhesive Transfer Tapes
3M™ Double Coated Tapes
40
41 42 43
This guide lists products that are commonly used for this specific application. It is important that the customer evaluates these suggested products in their specific application.
Sealing: Tape or sealant is applied over a seam to prevent fluid ingress or fluid Possible Adhesive or
egress. Examples include roof seams on vehicles, seams on metal enclosures Tape Requirements:
and pipe sealing. • Highly elongating/flexible
Potting and Encapsulating: Adhesive flows over and around a component or fills • Fast cure for painting
in a chamber to protect components therein. Examples include heavy duty
• Durability
electrical cords and connectors, electronics in plastic cases, circuit boards
and concrete repair.
Flowability* N/A
*3M™ Scotch-Weld™ Structural Adhesives and 3M™ Hot Melt Adhesives are used for potting and encapsulating where their flow and conformability allow them to fill into, or dome
over, complex shapes. 3M™ Adhesive Sealants are thick and can be dispensed into wide vertical or horizontal gaps, as well as over seams. 3M™ Extreme Sealing Tape seals over
seams and narrow gaps but does not flow into gaps. It can conform over low profile objects such as rivet heads.
Assembly Solutions
Stainless, Galvanized) Painted Metal, Composite Panel) Glass Polycarbonate, Nylon) (Polypropylene, Polyethylene)
DP8010 Blue
3797, 3748 VO
Plastics: LSE
*540, *740
*4411B, *4411N,
*4411G
44 45 46
This guide lists products that are commonly used for this specific application. It is important that the customer evaluates these suggested products in their specific application.
Metal Surfaces (High Surface Energy) High Surface Energy Plastics (HSE) Low Surface Energy Plastics (LSE)
293
3M Industrial Adhesives and Tapes | October 2017 Edition 17
3M Industrial Adhesives and Tapes
Last.
to help them design beyond the
limits of mechanical fasteners to
create next generation products.
Trusted innovations
from aerospace to
office space
With over 60 years of experience developing
innovative structural adhesives for aerospace,
automotive and hundreds of other industries,
3M delivers the solutions you can trust.
Our advanced formulations create durable
bonds, even on challenging materials or in
extreme conditions.
3M global service
and support
3M supports our customers with the testing,
technology, and training needed to create
better products. Our world-wide support
staff has the experience you can rely on
for everything from structural adhesive
selection to process improvement.
Leverage 3M’s proven selection of structural
adhesives, deep industry expertise, and
technical support to your advantage.
Design with Confidence. Build to Last.
296
Improve Aesthetics: Improve product appearance with Freedom of Design: Join composites to metal, build
invisible joints and smoother bond lines, reduce weight with hard-to-bond plastics, and use thinner, lighter
and noise, enhance corrosion and fatigue resistance, weight materials.
and more.
Process Efficiencies
298
Enhance Productivity: Reduce labor and material Accurate and Easy: Dispense by hand or with automated
costs, build faster with minimal surface prep and match equipment, and choose from a wide range of viscosities
cure rates to your process needs. and flow rates.
Performance Optimization
299
Strong, Flexible Bonds: Adhesives bond and seal Increased Durability: Resist chemicals, environment,
simultaneously, eliminate stress concentration and galvanic corrosion, fatigue, and material separation
absorb shock and vibration for durable bonds. along edges or corners.
Q: What materials will be bonded? Q: What types of joints are best for
300
A: Structural adhesives structural adhesives?
303
work by adhering to A: Joint designs that put
the top surface of the the adhesive bond
bonded parts, so it’s under shear, tension,
important to know or compression forces
the exact material and will provide the highest
condition on those strength. Designs that
surfaces. For metals, tend to apply peel or
will the adhesive be cleavage forces to the
applied to bare metal, adhesive, where the
or will there be a paint applied stresses are
or coating on the surface? For plastics, exactly which not distributed over
base resin? Could there be residual release agents the entire bond area, will have lower bond strength,
on the surfaces used for mold release? but the bond may still be sufficient for the needs
of the application. In addition, optimum bond line
Q: What is the preferred cure speed? 301 thickness typically ranges from 0.005" to 0.020".
A: The chosen structural
The adhesive qualification process should always
adhesive must have
include testing of prototype assemblies to ensure
enough work life
the adhesive will provide enough performance.
(open time, pot life)
to allow proper mixing Q: How are structural adhesives used and applied?
and application of A: Structural adhesives
the adhesive and come in many forms,
assembling of the including low viscosity
bonded parts. Smaller liquids and non-sag
assemblies or shorter pastes, one- and
cycle time production two-component
processes may be able to use a faster curing formulations, short and
adhesive with a work life of only five minutes or long work lives, and
less, while larger assemblies that require alignment various package sizes
and clamping will probably need a work life of and shapes. Most
20 minutes or more. two-part structural 304
Q: What surface preparation will be required? adhesives are available in both bulk containers and
302
convenient, easy-to-use cartridge mixing systems.
A: Structural adhesives
generally prefer clean, Q: What are the general characteristics of the
rough, dry surfaces for different types of structural adhesives?
305
highest bond strength. A: All structural
This typically means adhesives provide at
either light abrasion least 1,000 psi of
and solvent cleaning of overlap shear strength
the surface, or solvent to aluminum, but the
cleaning followed by different adhesive
chemical etching or chemistries have
applying a primer. various properties.
Adhesion tests should be performed to determine the
adequate surface preparation for a specific application.
Key Products
DP420NS Black, DP8810NS, PR100, TS230
Specialty Vehicle
Key Features and Benefits 75 76
• Weight reduction
• High strength
74
• Vibration and fatigue resistance
Key Products
DP8410NS, LSB60NS, TL42
Signage
Key Features and Benefits 72
• UL recognition
Key Products
DP8805NS, DP8405NS, DP100 Plus
Metalworking
Key Features and Benefits
• High strength and durability
66
• Reduced surface preparation
before bonding, and no grinding
after bonding 35 68
• Save weight and improve appearance
with adhesives instead of welds or rivets
Key Products
DP420NS Black, DP8407NS, DP8410NS
Key Products
DP420NS Black, DP8810NS, PR100, TS230
Appliance
Key Features and Benefits 63
Key Products
DP125 Gray, DP8810NS, TS230, TL42
Aerospace
Key Features and Benefits 59
Key Products
2216 Gray, DP100FR, DP640 60
• Plastic PUR
Acrylic
• Plastic PUR
• P lastic &
• Toughened CA
Rubber CA
Structural Adhesive Families Low Odor Acrylic Adhesives: Less odor than typical
acrylic adhesives and faster rate of strength build than
Rigid Epoxy Adhesives: Higher tensile strength at lower
most two-part structural adhesives. Excellent adhesion
elongations for greater long-term holding power. Mostly
to a variety of materials, including plastics and paint
used for rigid substrates (metals) with high static loads.
systems. They provide high impact resistance for plastic
Flexible Epoxy Adhesives: Lower tensile strength at bonds; and are tolerant of many surface contaminations.
higher elongations for greater capability to withstand
LSE Acrylic Adhesives: Outstanding adhesion to
differential movement of bonded parts; higher peel
polyolefin materials such as polypropylene, polyethylene
strength and higher adhesion to most plastics.
and TPO without surface treatment.
Toughened Epoxy Adhesives: Higher tensile strength
Semi-rigid Urethane Adhesives: Higher tensile
at lower elongations for fatigue resistance; best suited for
modulus and lower elongation capability, with greater
dynamic stresses. They have long-term holding power,
long-term holding power.
higher peel strength, and exceptional higher resistance
against shock, vibration and impact loads. Lower adhesion Flexible Urethane Adhesives: Lower tensile modulus
to most thermoplastics. and higher elongation capability. Excellent adhesion to
most plastics.
Heat-cured Epoxy Adhesives: One-component, rigid
adhesives with outstanding strength at elevated tempera-
tures. These adhesives require a thermal cure, typically Instant Adhesive Families
around 250–350°F (120–180°C) for 40–60 minutes. Plastic & Rubber (PR) Instant Adhesives: Bond to the
MMA Acrylic Adhesives: Provides greater adhesion to widest variety of materials, have an extremely fast cure
a wide variety of materials including most plastics and speed, and come in a wide range of viscosity.
paint systems, are tolerant of many surface Surface Insensitive (SI) Instant Adhesives: Cure even
contaminations. High impact resistance for metal bonds. on acidic surfaces (such as wood, paper, leather, and
ceramic); these adhesives have a slower cure speed than
traditional instant adhesives.
SUBSTRATE
SUBSTRATE
ATTRIBUTE
SMC variable temperature variable constant
temperature temperature temperature
PRODUCT FAMILIES
PRODUCT FAMILIES
Toughened Epoxy
• • MMA Acrylic • Flexible • Toughened Wood PUR
• Flexible Epoxy
• • Rigid Epoxy
Low Odor Acrylic Epoxy Epoxy
Flexible Epoxy
• •
Rigid Epoxy
• • Flexible
• Flexible Epoxy
• Toughened Epoxy • Flexible Epoxy
Toughened CA
• • Semi-rigid Flexible Epoxy
•
• Plastic PUR Urethane
Urethane Semi-rigid Urethane
•
• Toughened
• Toughened CA • Flexible Epoxy
Urethane Surface Insensitive CA
•
• Plastic PUR
• Plastic PUR
Low Odor (LO) Instant Adhesives: Provide a Retaining Compounds (RT): Bond and seal non-threaded
reduced blooming effect for applications that require cylindrical metal assemblies, such as press-fit or
an improved appearance. slip-fit parts; these adhesives replace keys, splines,
General Purpose (EC) Instant Adhesives: Slightly less and set screws.
expensive products that have lower strength and impact Pipe Sealants (PS): Provide a pressure seal on threaded
resistance compared to traditional instant adhesives. tubes and pipes; these adhesives replace various tapes
Super Fast (SF) Instant Adhesives: Provide the fastest and pastes.
rate of cure speed for most applications. Gasket Makers (GM): Fill voids between metal parts to
Rubber Toughened (RT) Instant Adhesives: Can create a form-in-place gasket; these adhesives replace
be used for applications that require improved impact o-rings and pre-formed gaskets.
strength or vibration resistance; preferred for applications
bonding two rigid materials together. PUR Adhesive Families
Metal (MC) Instant Adhesives: Provide improved Wood PUR: Higher shear strength at lower elongations
performance on metal substrates. for long term holding power. Mostly used for rigid wood
substrates and some plastics.
Engineered Grade (EG) Instant Adhesives: Provide
excellent overall performance for most applications. Plastic PUR: Higher impact strength, elongation and
flexibility for greater capacity to withstand movement
Anaerobic Adhesive Families of bonded parts. Higher adhesion to most plastics,
glass and aluminum.
Threadlockers (TL): Hold screws and other threaded
fasteners in place to prevent loosening from shock,
vibration, and thermal expansion and contraction; these
adhesives replace lock washers and nylon-insert nuts.
Substrate Selector
Step 1: Select Substrate Step 2: Determine Key Attribute Step 3: Select Product (see definitions below)
General LSE Acrylic* LO Acrylic Plastic & Toughened LO Acrylic DP8407NS LO Acrylic DP8407NS
Purpose Plastic & MMA Acrylic Rubber CA* Epoxy MMA Acrylic Toughened Epoxy MMA Acrylic
Rubber CA Plastic PUR Plastic PUR Flexible Epoxy Flexible Epoxy Flexible Epoxy
Flexible Epoxy Plastic PUR Plastic PUR
Plastic & Rubber CA Plastic & Rubber CA Plastic & Rubber CA
Plastic & Plastic & Plastic & N/A Flexible Epoxy Flexible Epoxy N/A N/A
Rubber
Rubber CA* Rubber CA* Rubber CA* Plastic PUR Plastic PUR
Plastic PUR
Temperature N/A Toughened Epoxy N/A Toughened Toughened Epoxy One-part Heat-cured Heat-cured
and Solvent Flexible Epoxy Epoxy Flexible Epoxy Heat-cured Epoxy Epoxy Epoxy
Resistant Flexible Epoxy Toughened Epoxy
Stainless LSE Acrylic LO Acrylic Plastic & Toughened LO Acrylic Heat-cured Epoxy LO Acrylic DP8407NS
Steel & MMA Acrylic Rubber CA* Epoxy MMA Acrylic Toughened Epoxy MMA Acrylic Heat-cured
Metals
Aluminum Flexible Epoxy Plastic PUR Flexible Epoxy Toughened Epoxy Epoxy
Plastic PUR Flexible Epoxy
Plastic & Rubber CA Rigid Epoxy
Toughened CA
Other LSE Acrylic DP8407NS Plastic & Heat-cured Heat-cured Epoxy Toughened Epoxy DP8407NS DP8407NS
Metals Toughened Epoxy Rubber CA* Epoxy Toughened Epoxy Flexible Epoxy Heat-cured Heat-cured
Flexible Epoxy Plastic PUR Toughened Epoxy Heat-cured Epoxy Epoxy Epoxy
Plastic PUR DP810
Plastic & Rubber CA
Stainless LSE Acrylic LO Acrylic N/A Heat-cured LO Acrylic DP8407NS LO Acrylic DP8407NS
Steel & MMA Acrylic Epoxy MMA Acrylic Heat-cured Epoxy MMA Acrylic
Oily Metals
Aluminum
Other LSE Acrylic DP8407NS N/A Heat-cured DP8407NS DP8407NS DP8407NS DP8407NS
Metals Epoxy Heat-cured Epoxy Heat-cured Epoxy Heat-cured
Epoxy
Fiberglass/ LSE Acrylic Semi-rigid Urethane Plastic & Toughened Semi-rigid Urethane Semi-rigid Urethane MMA Acrylic DP8407NS
SMC Toughened MMA Acrylic Rubber CA* Epoxy MMA Acrylic Toughened Epoxy LO Acrylic
CA* LO Acrylic Plastic PUR Flexible Epoxy LO Acrylic Flexible Epoxy
Flexible Urethane Plastic PUR Toughened Epoxy Plastic PUR
Composites
LSE Acrylic Wood PUR Plastic PUR Toughened Plastic PUR Plastic PUR N/A N/A
Surface Flexible Epoxy Surface Epoxy Toughened Epoxy Toughened Epoxy
Wood
Bold = Best In Class Product Light = Suggested Alternate Product * = With Primer
Composites Concrete/Stone/Ceramics/Glass
Energy
General Semi-rigid Urethane Semi-rigid Urethane Flexible Epoxy Flexible Epoxy Wood PUR
Purpose MMA Acrylic MMA Acrylic Rigid Urethane Flexible Urethane Flexible Epoxy
LO Acrylic Flexible Flexible Epoxy Flexible Urethane Plastic PUR Rigid Urethane
Urethane Toughened Epoxy Plastic PUR Surface Insensitive CA
Plastic PUR Plastic PUR Plastic PUR Plastic PUR Plastic PUR
Flexible Epoxy
Temperature Toughened Epoxy Toughened Epoxy Toughened Epoxy Flexible Epoxy Toughened Epoxy
and Solvent Flexible Epoxy Flexible Epoxy Flexible Epoxy Plastic PUR
Resistant Plastic PUR Plastic PUR Flexible Epoxy
Stainless Semi-rigid Urethane Semi-rigid Urethane Toughened Epoxy Flexible Epoxy Plastic PUR
Steel & MMA Acrylic Toughened Epoxy Flexible Epoxy Toughened Epoxy
Metals
Fiberglass/ Semi-rigid Urethane Semi-rigid Urethane Semi-rigid Urethane Semi-rigid Urethane Semi-rigid Urethane
SMC MMA Acrylic Toughened Epoxy Toughened Epoxy Flexible Epoxy Toughened Epoxy
LO Acrylic Flexible Epoxy Flexible Epoxy Flexible Urethane Rigid Urethane
Toughened Epoxy Plastic PUR Plastic PUR Plastic PUR Flexible Epoxy
Flexible Epoxy Toughened CA Plastic PUR
Composites
Plastic PUR
Toughened CA
Epoxy Semi-rigid Urethane Toughened Epoxy Semi-rigid Urethane Semi-rigid Urethane Semi-rigid Urethane
Toughened Epoxy Flexible Epoxy Toughened Epoxy Flexible Epoxy Toughened Epoxy
Flexible Epoxy Plastic PUR Flexible Epoxy Plastic PUR Flexible Epoxy
Plastic PUR Toughened CA Plastic PUR Plastic PUR
Toughened CA
Indoor Semi-rigid Urethane Semi-rigid Urethane Toughened Epoxy Flexible Epoxy Flexible Epoxy
Concrete/Stone/
Toughened Epoxy Toughened Epoxy Flexible Epoxy Flexible Urethane Plastic PUR
Ceramics/Glass
Rigid Urethane Flexible Epoxy Flexible Urethane Flexible Urethane Toughened Epoxy
Flexible Epoxy Plastic PUR Rigid Urethane
Plastic PUR Surface Insensitive CA
Bold = Best In Class Product Light = Suggested Alternate Product * = With Primer
Bead Size Linear ft/m Linear ft/m Linear ft/m Linear ft/m Linear ft/m Linear ft/m Linear ft/m Linear ft/m
Dimension* per 37mL per 43mL per 45 mL per 50mL per 200mL per 400mL per 490mL per 295mL
inches (mm) (2:1 Cart.) (2:3 Cart.) (10:1 Cart.) (1:1 & Cart.) (1:1 & 2:1 Cart.) (1:1 & 2:1 Cart.) (10:1 Cart.) (1/10 gal Cart.)
1/2" (12.7mm) 2 ft (0.6m) 2 ft (0.7m) 2 ft (0.7m) 2.5 ft (0.8m) 10 ft (3m) 21 ft (6m) 26 ft (8m) 20 ft (6m)
3/8" (9.5mm) 3.5 ft (1m) 4 ft (1m) 4 ft (1m) 4.5 ft (1m) 18 ft (6m) 37 ft (11m) 45 ft (14m) 35 ft (11m)
1/4" (6.4mm) 8 ft (2m) 9 ft (3m) 9 ft (3m) 11 ft (3m) 41 ft (13m) 83 ft (25m) 102 ft (31m) 79 ft (24m)
1/8" (3.2mm) 31 ft (9m) 36 ft (11m) 37 ft (11m) 42 ft (13m) 165 ft (50m) 331 ft (101m) 405 ft (123m) 312 ft (95m)
1/16" (1.6mm) 122 ft (37m) 142 ft (43m) 147 ft (45m) 165 ft (50m) 656 ft (200m) 1,313 ft (400m) 1,600 ft (488m) 1,234 ft (376m)
Coverages per Gallon for Various Coverages per Gallon for Various
Thicknesses of 100% Solids 3M Adhesives Bead Sizes of 100% Solids 3M Adhesives
Wet Thickness Ft2/gal gal/1,000 ft2 Bead Size Dimension* Approx. lineal ft/gal Approx. gal/1,000 lineal ft
inches (mm) (m2/L) (L/1,000m2) inches (mm) (m/L) (liter/1,000m)
1/2" (12.7mm) 3 ft2 (0.1m2) 312 gal (12,700L) 1/2" (12.7mm) 196 ft (16m) 5 gal (63L)
1/8" (3.2mm) 13 ft2 (0.3m2) 78 gal (3,175L) 3/8" (9.5mm) 350 ft (28m) 3 gal (36L)
1/16" (1.6mm) 26 ft2 (0.6m2) 39 gal (1,587L) 1/4" (6.4mm) 785 ft (63m) 1.3 gal (16L)
1/32" (0.8mm) 51 ft2 (1m2) 20 gal (794L) 1/8" (3.2mm) 3,130 ft (252m) 0.3 gal (4L)
25 mils (0.64mm) 64 ft2 (1.5m2) 16 gal (635L) 1/16" (1.6mm) 12,420 ft (1,000m) 0.1 gal (1L)
5 mils (0.13mm) 320 ft2 (8m2) 3 gal (127L)
*Bead size is semi-circular bead with width equal to size noted and height at center of bead equal to 1/2 the width.
NOTE: The technical information and data provided here should be considered representative or typical only and should not be used for specification purposes.
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
High
DP125 200mL 00-021200-87844-2 62-3293-3830-5
performance, 90 3,400 4,300 400
125 1:1 52,500 25 min 2.5 hr 400mL 00-021200-87845-9 62-3293-3530-1
Very flexible (160) (23) (30) (3)
(Gray) 5 gal pail A 00-021200-87218-1 62-3393-8530-4
bonds
5 gal pail B 00-021200-87217-4 62-3293-8530-6
High
DP125 50mL 00-021200-87211-2 62-3291-1435-9
performance, 85 4,000 2,500 150
125 1:1 15,000 25 min 2.5 hr 200mL 00-021200-87842-8 62-3291-3830-9
Very flexible (151) (28) (17) (1)
(Translucent) 400mL 00-021200-87843-5 62-3291-3530-5
bonds
High
50mL 00-021200-87219-8 62-3286-1435-9
DP190 performance 60 3,500 1,200 150
1:1 10,000 80 min 6 hr 200mL 00-021200-87838-1 62-3286-3830-9
(Translucent) Flexible (107) (24) (8) (1)
400mL 00-021200-87839-8 62-3286-3530-5
bonds
43mL Duo-Pak 00-021200-56659-2 62-2216-1435-7
2 oz tube kit 00-021200-20351-0 62-2216-0530-6
Pint kit 00-021200-20354-1 62-2216-5430-4
High
Qt kit 00-021200-20356-5 62-2216-6430-3
2216 B/A performance 3,000 3,200 400
* (Gray) Very flexible
2:3 80,000 90 min 10 hr 50 (89)
(21) (22) (3)
Gal kit
5 gal pail A
00-021200-20358-9
00-021200-20365-7
62-2216-7430-2
62-2217-8530-6
bonds
5 gal pail B 00-021200-20360-2 62-2216-8530-8
55 gal drum A 00-021200-20366-4 62-2217-9530-5
55 gal drum B 00-021200-20361-9 62-2216-9530-7
2 oz tube kit 00-021200-20851-5 62-3508-0530-5
Pint kit 00-021200-20852-2 62-3508-5430-3
General Qt kit 00-021200-20854-6 62-3508-6430-2
2216 B/A purpose 70 3,000 1,700 140 Gal kit 00-021200-20856-0 62-3508-7430-1
1:1 10,000 2 hr 14 hr
(Translucent) Very flexible (125) (21) (12) (1) 5 gal pail A 00-021200-64981-3 62-3608-8535-4
bonds 5 gal pail B 00-021200-64980-6 62-3508-8535-6
55 gal drum A 00-021200-20927-7 62-3608-9530-4
55 gal drum B 00-021200-20859-1 62-3508-9530-6
High
2216NS B/A 50 2,000 2,500 400 5 gal pail A 00-021200-87180-1 62-3378-8530-5
performance 2:3 350,000 2 hr 10 hr
(Tan) (89) (14) (17) (3) 5 gal pail B 00-021200-87179-5 62-3278-8530-7
Non-sag
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Approx. Approx.
Approx. Mixed Time to Floating
Mix Viscosity Work Handling Roller Overlap Shear: psi (MPa)
Ratio at 75°F Life Strength Peel PLI
Product (Vol.) (24°C) at 75°F at 75°F (N/cm) at -20°F 75°F 180°F
(Color) Key Features B:A (cP) (24°C) (24°C) 75°F (24°C) (-29°C) (24°C) (82°C) Size UPC Stock #
3M™ Scotch-Weld™ Standard MMA Acrylics
DP805 Fast strength
35 2,500 3,500 2,200 47mL 00-021200-83758-6 62-3288-1435-5
* (Light
Yellow)
build, Minimal
surface prep
1:1 110,000 3 min 10 min
(62) (17) (24) (15) 200mL 00-021200-87828-2 62-3288-3830-5
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
DP601NS
8 2,700 2,300 700
601NS Rigid, Non-sag 1:1 Paste 1 min 4 min 50mL 00-021200-96407-7 62-2652-5031-6
(14) (19) (16) (5)
(Gray)
50mL 00-021200-82252-0 62-3592-1435-0
DP605NS
Semi-rigid, 40 4,000 2,000 600 200mL 00-021200-87853-4 62-3592-3830-0
605NS 1:1 150,000 5 min 20 min
Non-sag (71) (28) (14) (4) 5 gal pail A 00-021200-82254-4 62-3692-8530-9
(Off-White)
5 gal pail B 00-021200-82253-7 62-3592-8530-1
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
313 81
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
314 315
0
psi 5 min 10 min 15 min 30 min 1h 2 hr
PUR PVA 2-Part Epoxy Hot Melt
316
Approx. Approx.
Viscosity Open Time
@250°F Time at to Handling
Product (121°C) 75°F Strength at Shore Elongation
(Color) Key Features (cP) (24°C) 75°F (24°C) D % Size UPC Stock #
3M™ Scotch-Weld™ PUR Adhesives – Plastic Bonders
EZ250030 Fast set time, bonds a wide 1/10 gal 00-051115-23541-2 62-3851-5230-1
13,000 2 min 30 sec 50 725
(Off-White) variety of plastics 5 gal 00-051115-23542-9 62-3851-8530-1
Purge
Purge PUR adhesives from
Material 8250 N/A N/A N/A N/A 5 gal 00-021200-56522-9 62-3733-8530-1
bulk dispensing equipment
3756
System Accessories for Applicator Bench Mount Bracket Assembly (bracket only) 00-021200-30086-8 62-9895-9950-1
hands-free dispensing Hot Melt Applicator Foot Pedal Assembly 9277 00-021200-82278-0 62-9277-9930-4
Repair Kits and Adhesive Applicator Housing/Shroud Assembly Kit 00-051115-25783-4 62-9865-9950-4
Replacement Parts Applicator Nozzle Shroud 00-048011-58320-4 62-9845-0029-8
Benchmount Quick Exhaust Assembly Replacement Kit 00-021200-31357-8 62-9895-9952-7
Applicator Air Coupler Filter Kit 00-021200-89475-6 62-9895-0001-2
Applicator Air Supply Line Kit 00-021200-89479-4 62-9895-0005-3
Applicator Air Valve Kit 00-048011-57410-3 62-9845-0009-0
Applicator Swivel Connector 00-048011-58298-6 62-9845-9934-0
Applicator End Cap 00-021200-89476-3 62-9895-0003-8
Applicator Heat Tube Assembly (120V) Kit 00-021200-89486-2 62-9895-0023-6
Applicator Heat Tube (240V) 00-021200-25303-4 62-9895-0043-4
Applicator On/Off Switch Kit 00-021200-89482-4 62-9895-0024-4
Applicator Power Cord Kit (120V) 00-021200-89481-7 62-9895-0021-0
Applicator Wire Stand 00-021200-89483-1 62-9895-0033-5
High Temperature (250°F) PUR Preheater Thermostat/TCO Kit 00-051115-23619-8 62-9865-9938-9
Low Temperature (170°F) PUR Preheater Thermostat/TCO Kit 00-051115-23618-1 62-9865-9990-0
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Typical
Product Viscosity Temperature Time to Full Cure
(Color) Key Features (cP) Range Handling (Hr) Size UPC Stock #
3M™ Scotch-Weld™ Instant Adhesives – Plastic and Rubber
PR Gel Fast cure, gel viscosity for -65° to 180°F 20g tube 00-051115-25265-5 62-6152-0362-7
Gel 20–60 sec 24
(Clear) maximum gap filling (-54° to 82°C) 300g cart 00-051115-25282-2 62-6152-3360-8
PR40 Low viscosity for close fitting -65° to 180°F 20g bottle 00-051115-25204-4 62-6147-0360-1
40 3–20 sec 24
(Clear) plastic/rubber parts (-54° to 82°C) 500g bottle 00-051115-25205-1 62-6147-3860-7
20g bottle 00-051115-25214-3 62-6164-0360-6
Key Product
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Typical
Product Viscosity Time to
(Color) Key Features (cP) Handling Full Cure (Hr) Size UPC Stock #
3M™ Scotch-Weld™ Instant Adhesive Primers & Activators
Instant adhesive activator,
2 fl oz bottle 00-051111-07795-5 62-6198-0860-3
AC09 Non-flammable, solvent-based, 1 1–5 sec 24
1L can 00-051111-07908-9 62-6198-8361-4
California compliant
Instant adhesive primer for bonding
2 fl oz bottle
of difficult-to-bond plastics such 00-048011-62728-1 62-3907-0860-0
AC77 <3 1–5 sec 24 4L can
as polyethylene, polypropylene 00-048011-62653-6 62-3907-7560-9
and polyacetal
Instant adhesive primer for bonding
2 fl oz bottle 00-051115-31388-2 62-3916-0860-1
of difficult-to-bond elastomers such
AC79 2 1–5 sec 24 8 fl oz bottle 00-051115-31389-9 62-3916-3760-0
as silicone, fluoroelastomer and
4L can 00-051115-31390-5 62-3916-7560-0
EPDM, VOC compliant
2 fl oz bottle 00-048011-62681-9 62-6194-0860-2
Instant adhesive general purpose 8 fl oz bottle 00-048011-62682-6 62-6194-3760-1
AC113 <3 1–5 sec 24
accelerator, Will not attack plastics 1L can 00-048011-62683-3 62-6194-6560-2
4L can 00-048011-62684-0 62-6194-7560-1
Instant adhesive acetone-based
2 fl oz bottle 00-048011-62685-7 62-6195-0860-9
accelerator flashes off rapidly,
AC452 <2 1–5 sec 24 8 fl oz bottle 00-048011-62686-4 62-6195-3760-8
Excellent adhesion, Overspray may
4L can 00-048011-62689-5 62-6195-7560-8
attack some plastics
Clear, colorless organic-based liquid
Surface 2 fl oz bottle 00-021200-87937-1 62-3804-0830-2
helps speed curing and prime surfaces, <10 1–5 sec 24
Activator
Comes with brush and spray pump
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
SURFACE PREPARATION
YES AC79
Is the substrate an elastormer?
PRIMER EG silicone, EPDM, Santoprene?
NO AC77
Which do you require?
Sensitive plastics AC113
ACTIVATOR AC452
AC09
85
Typical
Product Viscosity Temperature Time to Full Cure
(Color) Key Features (cP) Range Handling (Hr) Size UPC Stock #
3M™ Scotch-Weld™ Anaerobic Adhesives – Threadlockers
Screwlock – low removal torque 10mL bottle 00-048011-62601-7 62-3493-1060-7
TL22 -65° to 300°F
fasteners less than 1,200 < 30 min 24 50mL bottle 00-048011-62602-4 62-3493-5060-3
(Purple) (-54° to 149°C)
a 1/4" (6mm) 250mL bottle 00-048011-62603-1 62-3493-3960-6
1mL pipette 00-048011-62604-8 62-3494-0160-4
10mL bottle 00-048011-62605-5 62-3494-1060-5
TL42 Nutlock – medium strength, -65° to 300°F
1,200 < 30 min 24 50mL bottle 00-048011-62606-2 62-3494-5060-1
(Blue) general purpose (-54° to 149°C)
250mL bottle 00-048011-62607-9 62-3494-3960-4
1L bottle 00-051115-25124-5 62-3494-8360-2
10mL bottle 00-051115-25138-2 62-3428-1060-3
TL43 Oil tolerant, medium strength, -65° to 300°F 50mL bottle 00-051115-25139-9 62-3428-5060-9
3,300 < 30 min 24
(Blue) general purpose (-54° to 149°C) 250mL bottle 00-051115-25140-5 62-3428-3960-2
1L bottle 00-051115-25141-2 62-3428-8360-0
10mL bottle 00-048011-62609-3 62-3495-1060-2
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Does it need to be oil tolerant? Are the parts pre-assembled? Are the threads Do you need
NO YES NO YES
FINE COARSE NO YES
Do you require high temp?
Do you require
NO YES
high temp?
TL22 TL42 TL43 TL71 TL62 TL77 TL72 TL90 335 HP42 HP45 PS67 PS65 PS77
Key Product Denotes product to consider first in this category. * After Key Products, consider these.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
NO YES
FLEXIBLE RIGID
Do you need
490mL (10:1)
48.5mL (1:1)
45mL (10:1)
50mL (1:1)
Product Replacement Plunger Orders Static Mixing Nozzle Options
3M™ Scotch-Weld™ EPX™ Plus II Applicator*
Stock #: 62-9170-9931-9 3M™ Scotch-Weld™ EPX™
UPC: 0-00-76308-86383-8 Mixing Nozzle 341
Square Gold, 37mL and 50mL
Stock #: 62-9171-9153-8 Bulk: 62-9171-9953-1
n UPC: 0-00-21200-50008-4 Bulk: 0-00-51115-81467-9
1:1 Plunger 3M™ EPX™ Mixing Nozzle 342
For low volume applications and take-it-to-the-job convenience, the 3M™ EPX™ Plus II and EPX™ metal manual applicators comfortably dispense any
of the 3M™ Scotch-Weld™ Duo-Pak Structural Adhesives. For higher volume applications, select the 200mL manual dispenser, or the 200mL or 400mL
pneumatic dispenser. For concrete repair, there are both manual or pneumatic options.
490mL (10:1)
48.5mL (1:1)
45mL (10:1)
50mL (1:1)
Product Replacement Plunger Orders Static Mixing Nozzle Options
3M™ EPX™ 200, 400mL Manual Applicator
Stock #: 62-9148-9930-7 3M™ Scotch-Weld™ EPX™
UPC: 0-00-51111-98073-6 Mixing Nozzle
Square Gold, 200mL and 400mL 345
Stock #: 62-9176-9127-1
UPC: 0-00-21200-97331-4
N/A n n n
3M™ Scotch-Weld™ EPX™
Mixing Nozzle
Helical White, 200mL and 400mL 346
322
Stock #: 62-9142-9930-0
UPC: 0-00-21200-87982-1
3M™ EPX™ 490mL Manual Applicator
Stock #: 62-9182-9930-6 3M™ Scotch-Weld™ EPX™
UPC: 0-00-51115-71115-2 Mixing Nozzle
Helical Orange, 490mL 347
Stock #: 62-9158-9136-0
UPC: 0-00-51115-69042-6
N/A n
3M™ Scotch-Weld™ EPX™
Mixing Nozzle
Square Green, 490mL 348
323
Stock #: 62-9184-9490-7
UPC: 0-00-51115-81619-2
3M™ Scotch-Weld™ EPX™ Pneumatic Applicator 200mL
Stock #: 62-9140-9930-4 3M™ Scotch-Weld™ EPX™
UPC: 0-00-21200-87978-4 Mixing Nozzle
Square Gold, 200mL and 400mL 345
Stock #: 62-9176-9127-1
UPC: 0-00-21200-97331-4
N/A n
3M™ Scotch-Weld™ EPX™
Mixing Nozzle
324 346
Helical White, 200mL and 400mL
Stock #: 62-9142-9930-0
UPC: 0-00-21200-87982-1
3M™ EPX™ 400mL Pneumatic Applicator
Stock #: 62-9145-9930-3 3M™ Scotch-Weld™ EPX™
UPC: 0-00-21200-87979-1 Mixing Nozzle
Square Gold, 200mL and 400mL 345
Stock #: 62-9176-9127-1
UPC: 0-00-21200-97331-4
N/A n
3M™ Scotch-Weld™ EPX™
Mixing Nozzle
Helical White, 200mL and 400mL 346
325
Stock #: 62-9142-9930-0
UPC: 0-00-21200-87982-1
3M™ EPX™ 490mL Pneumatic Applicator
Stock #: 62-9152-9930-9 3M™ Scotch-Weld™ EPX™
UPC: 0-00-51115-69041-9 Mixing Nozzle
Helical Orange, 490mL 347
Stock #: 62-9158-9136-0
UPC: 0-00-51115-69042-6
N/A n
3M™ Scotch-Weld™ EPX™
Mixing Nozzle
326 Square Green, 490mL 348
Stock #: 62-9184-9490-7
UPC: 0-00-51115-81619-2
Standard Caulk Gun
3M™ Concrete Repair 8.4 oz
Image not available N/A 3M™ Concrete Repair Urethane Cartridge Nozzles 349
8.4 oz Cartridge Nozzles Stock #: 62-9637-9935-8
UPC: 0-00-48011-53382-7
3M™ Scotch-Weld™ One-Part Heat Cured Epoxies require a unique manual or pneumatic dispenser, such as Semco® 250, 350, 850, 950, or equivalent.
81 103 104
3M Concrete Repair
™
Make fast work of lengthy 3M concrete repair formulations
600 self-leveling flows expansion or control joints and harden to any depth without
smoothly into cleaned other larger jobs with the heavy- cracking for custom threading
cracks and gaps and duty manual applicator and 12 fl and anchoring.
hardens in as little as oz duo-pak cartridges.
5 minutes.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
118 119
In display cases for jewelry and other retail In carrying case assembly, 3M Hot Melt
™
items, foam is bonded to foam and fabric. Spray Adhesive bonds foam to foam,
Low temperature spray will not damage plywood, metal or plastic.
heat-sensitive substrates.
1 Bonds were made by spraying adhesive onto 3/4" thick, 2 lb. density polyester urethane foam. Open time will vary depending on substrate.
2 Tested per 3M IATD test method C-3093 using 2 lb. dead load.
3 According to 3M IATD test method C-3012. 180° peel strength was determined at a cross head speed of 2"/min at 73°F (23°C).
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
129°C) adhesive effectively bonds heat-sensitive substrates such as styrene foam to itself,
and more. corrugated or other surfaces without damaging the foam.
For bonding the guide to a drawer bottom, For sample and display boards, attach For economical package sealing, 3M™ Hot
3M™ Hot Melt Adhesive 3792 provides high wood flooring, laminates, foams, fabrics Melt Adhesive 3762 is a versatile formulation
delivery rate and long bonding range. or other materials and small products with with a bonding range for production speed.
3M™ Hot Melt Adhesive 3792. Variety of tips for package types.
To help with sound dampening on drawer 3M™ Hot Melt Applicator LT and 3M™ Hot Melt For versatility in P.O.P. assembly,
bottoms, use 3M™ Hot Melt Adhesive 3792. Adhesive 3792LM applied at low temperature 3M™ Hot Melt Adhesive 3792 bonds a variety
(265°F/129°C) make quick work of welting, of plastics, woods and light gauge metals.
gimping, and bonding fabric to wood.
3M™ Hot Melt Applicator LT. Low-medium 3M™ Hot Melt Applicator LT with 3M™ Pneumatic Hot Melt Applicator PG II LT
volume using low melt adhesive. Quadrack™ Converter. Medium volume with Speedloader. High volume using low
UPC# 021200-82245 using low melt adhesive. melt adhesive.
UPC# 021200-89447 UPC# 021200-89395
D E F
3M™ Hot Melt Applicator AE II LT. 3M™ Hot Melt Applicator TC. 3M™ Hot Melt Applicator TC with
Low volume using low melt adhesive. Low-medium volume. Quadrack™ Converter. Medium volume.
UPC# 051115-25567 UPC# 021200-82244 UPC# 021200-89445
G H I
1 – Weight shown is for applicator only; does not include adhesive capacity.
2 – Adhesive output will vary with conditions and the adhesive used. Values are approximate and are based on maximum steady-state flow.
3 – Temperatures shown are nominal control values. Actual temperature will range slightly above and below this value.
142
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
UL 94
Product Color FDA Listed1 Listing Features/Application Ideas
Low Melt Technology: Applied 250–270°F (121–132°C)
Excellent “hot tack”, fast setting for corrugated, beadboard, repack, recoup.
3750LM Tan – N/A
Economical, general purpose. Use with AE II LT applicator only.
Excellent “hot tack”, fast setting for corrugated, beadboard, recouperage, repacking chipboard and wood.
3762LM* Light Amber Yes N/A
Economical, general purpose. Use with low melt applicator only.
3776LM Tan – N/A Bonds variety of plastics, woods and light-gauge metals. Use with low melt applicator only.
Clear, multi-purpose for wood, coated paper, polyolefins and other heat-sensitive materials.
3792LM* Clear Yes V2
P.O.P. displays. Use with low melt applicator only.
Removable “gummy glue” for many substrates. Removes easily without residual tack.
3798LM* Light Yellow Yes N/A
Use with low melt applicator only.
Hot Melt Technology: Applied 350–385°F (177–196°C)
3731* Tan – N/A High heat resistance. Bonds plastics including polyethylene, polypropylene.
High delivery rate and long bonding range. General purpose for foundry sand cores, wood bonding,
3738* Tan Yes V2
corrugated, selected plastics and chipboard.
3747 Tan Yes N/A General purpose for wide variety of plastics, wood and lightweight metals.
Good thermal shock resistance. Non-corrosive to copper for many electronic applications.
3748* Off-White Yes V2
Bonds polyolefins.
3750 Tan – N/A Low viscosity for high flow rate, increased production. Good hot tack, quick grab for packaging and woodworking.
3750 Clear – N/A Low viscosity for high flow rate, increased production. Good hot tack, quick grab for packaging and woodworking.
Excellent “hot tack”, fast setting for corrugated, beadboard, recouperage, repacking chipboard and wood.
3762 Tan Yes V2
Economical, general purpose.
3764* Clear Yes V2 Bonds variety of plastics including polycarbonate, polyethylene, and polypropylene. Flexible at low temperatures.
3779* Amber Yes N/A High heat resistance. High strength. Good fuel and oil resistance. Electronics.
3789* Brown Yes V2 High performance for plastics. Impact resistant. Bonds vinyl and wood. Good fuel and oil resistance.
3792* Clear Yes V2 Clear, multi-purpose for wood, corrugated, fabric, furniture, upholstery, novelties, and other lightweight materials.
3797 Off-White Yes V2 High ball and ring. Low viscosity. Good for electrical potting.
Bulk Only
3794 Hi
Light Tan Yes N/A Sprayable high tack PSA for bonding plastic, paper, metals, die-cut labels.
Tack PSA
6111 Tan – N/A Sprayable 100% solventless adhesive for most foams, fabrics, plastics, particle board and thin metal.
6111HT Tan, Blue – N/A Similar to 6111 but has higher heat resistance. Available in tan and blue.
6116 Off-White – N/A Similar to 6111 but lower than normal viscosity and mainly used on fabrics.
1/2" x 12" AE N/A 4,000 @ 250°F 45 200 (95) 128 (54) 6 475 25
5/8" x 8" Q
5 12,000 @ 375°F N/A 315 (157) 265 (130) 22 490 30
1" x 3" PG
1/2" x 12" AE N/A 1,900 @ 375°F 30-40 200 (93) 125 (52) 6 500 N/A
1/2" x 10" AE N/A 4,800 @ 375°F 35-45 178 (81) 135 (57) 12 250 N/A
Bulk pillows N/A 15,000 @ 325°F N/A 224 (107) 120 (49) 16 N/A > 60
3,000–5,000 @ 1 surface: 60
.75" x.75" chips N/A N/A 224 (107) 145 (63) 34 N/A
375°F 2 surface: 360
1 surface: 120
.75" x.75" chips N/A 1,300 @ 375°F N/A 199 (93) 160 (69) 20 N/A
2 surface: 300
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
8
3M™ Solvent and Water Based Adhesives start with the customer. Their process, their
requirements and their wishes. Then the 3M team of industry experts, in conjunction
with our comprehensive technology portfolio, offers customers versatility, efficiency
and confidence to answer their “what if?”
Do i
• No m
at
290 expert
is
help yo
u
• From
wo
lamina
tio
Performance Productivity materia
ls
Find the RIGHT product for your Our goal is to make your business as efficient and
assembly with the RIGHT questions: effective as possible. How the adhesive gets to your
• What substrates are being bonded? assembly is equally as important as theFadhesive
indingitself.
your
• What are the issues with your current product? 3M Ad
We work with you to integrate the best delivery system
for your process.
hesive
100,00
• Are there any environmental Health and Safety
requirements?
Cylinders
& Taandpe
• Self-contained
0
• Are there specific product attributes needed? A ssem
pressurized
bly Sol
• Are there specific manufacturing requirements? • Portable utions
Dosprayed?
• What is the size of the substrate being it bo
• 3M h
as b
ldly. • Minimal equipment
for dec een a world le
ades a ader in
patent
s investment
• Quali nd we bondin
have th
ty, con
sistenc e paten g technolog • Low maintenance
you loo ts to pro y
1
k for in y and reli ve it.
quest fo ab ability—
r new in onding soluti the att
ri b utes • Optimized spray
on—he
Sustainability novatio
ns. lp drive
our
pattern cuts waste and
145
Low Emissions. High Standards. maximizes coverage
right
Going “green” does not mean that
to do it
you have to give up on performance.
For 40 years our engineers have been
chance
developing water-based, low VOC and
GREENGUARD™ Certified adhesives Do it re
that have been used in the most sponsi
demanding applications. 328
• Susta
inabilit
y is a n
bly.
• We d atural e
146 evelop xtensio
ever — ed th n of 3M
Aerosols more th e first water- ’s corp
orate v
• We h a n 40 ye based alue
contac
So, are you ready to go “green?” ave a w
• Convenient
contrib
ute to L for
ide sele
ars ago
ction o
. t adhesi
ve
EED ® f Low V
We’re ready to take you there. smaller jobs or credits and areOGCR products that he
EENGU lp
ARD ™ C
multiple stations ertifie
327 Bulk
• Cost effective
• Integrate into
existing equipment
150
149
70 FAST TACKING
74NF Non-flammable
The variety of applications for these multi-purpose adhesives is nearly endless. From adhering pool table felt, to building architectural models, and
even bonding protective materials like dense foams into electronics, musical instrument or sensitive equipment cases. 3M has a spray adhesive
solution to fit customers’ needs.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
• Trade show displays Marine and specialty vehicle applications, like installing carpet, rubber or
synthetic flooring, are perfect for 3M sprayable adhesives. Our quick tack,
low VOC and cylinder delivery are common benefits in this market.
HEAVY DUTY – Solvent Based Adhesives
Product Requirement Size Availability
Product
Key
90 High strength
98 NF Non-flammable
Plasticizer resistance,
1099
harsh environments
158
HEAVY-DUTY – Water Based Adhesives Consider trade show exhibits and store fixtures that are often updated
Product Requirement Size Availability several times a year. 3M’s adhesive line offers very low cost per square foot
bonded for applications where our customers value total applied cost.
Product
Key
159 160
3M™ Hi-Strength 90 Spray Adhesive has a long reputation of holding strong in critical applications like this edge banding strip. Also, 3M has multiple adhesives
that are postformable. Postforming is where the laminate is heated and bent as much as 360° around a radius.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
155
Foam and fabric applications can be very challenging. From soft bond lines
to tight radiuses, our lineup can meet the demand. The 3M portfolio of water
and solvent based adhesives truly give the customer “flexibility.”
74NF Non-flammable
100NF +
Faster initial strength
Activator
One surface bonding,
1000NF
higher heat resistance
156
Aerosol adhesives provide either web or mist spray patterns with higher solid
Aerosol Cylinder Bulk content than our competitors. This combination allows 3M adhesives to sit
on the surface versus soaking in. More adhesive on the surface results in less
adhesive usage and a better bond for the customer.
157
These solvent and water based adhesives are often used as a “third hand” to
hold lightweight materials in place until they can be sewn or held in place by
other assembly methods.
80 Aerosol
161
SPECIALTY – Plastic Adhesives
With excellent resistance to fuel and oil, 3M™ Nitrile High Performance
Product Requirement Size Availability Rubber and Gasket Adhesive 847 bonds and seals chemical drum gaskets
in place.
Product
1099
AND PLASTICIZER
90 Aerosol
162
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
3M™ Silicone Spray Low VOC 60% lubricates For fast, easy cleanup of gears, 3M™ Industrial 3M™ Adhesive Remover removes adhesive
cutting tools and tables. Fast, easy application Citrus Base Cleaner helps soften and loosen without damaging surface underneath.
helps prevent buildup of adhesive, wax, inks grease, oil and grime. After using this
and paints. Won’t stain or become gummy. heavy-duty degreaser/cleaner, just wipe
away with a shop towel.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Product Selection
The lead products for
3M™ Cylinder Adhesives are:
• 3M™ Postforming 94 CA Cylinder
Spray Adhesive
• 3M™ Hi-Strength 94 ET Cylinder
Spray Adhesive
• 3M™ Holdfast 70 Cylinder
Spray Adhesive 3M™ Postforming 94 CA Cylinder Spray For fast, easy foam board installation, above
Adhesive is a low telegraphing that dries and below grade, simply spray and stick with
The majority of applications quickly to reach postformable strength in 1–5 3M™ HoldFast 70 Cylinder Spray Adhesive.
can be done with these three minutes. A 1–15 minute open time provides Bonds foam to concrete, waterproofing, OSB
flexibility in assembly speed. 3M™ Hi-Strength and more without damaging the foam.
cylinder products. 94 ET Cylinder Spray Adhesive offers all the
benefits of 3M™ Postforming 94 CA Cylinder
Spray Adhesive, but delivers a higher tack
and increased bonding range.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Solids Weight
Product Available Format Percent (Approx.) Key Characteristics
MULTI-PURPOSE – Solvent Based Adhesives
Multi-Purpose 27 Aerosol 21% Fast tack. Lightweight applications. Mist spray pattern.
5 gal, 54 gal 43% High solids for increased coverage. High tack general
General Purpose 60 CA
Large, Int and Jumbo Cylinder 42% purpose adhesive.
5 gal, 52 gal 26% Extremely versatile and very fast tacking. Unique wide web
HoldFast 70 spray pattern with heavy body and low soak-in. Bonds polystyrene
Large, Int and Jumbo Cylinder 21% without degrading surface.
Aerosol 25%
Low soak-in for long lasting bond. High coverage and aggressive
Super 77™ 5 gal, 52 gal 36%
tack. Bonds quickly in 15 seconds.
Large Cylinder 27%
Super 77™ CA Multi-Purpose
Aerosol 19% Aggressive tack. Quick bonding. Long bonding range.
(Low VOC)
Fast tacking, high performance, pressure sensitive adhesive
5 gal box, 5 gal, 52 gal,
Fastbond™ Insulation Adhesive 49 55% for lightweight materials. Low VOC and GREENGUARD® Certified.
100 gal, 255 gal
UL MAGW2 component recognition.
HEAVY DUTY– Solvent Based Adhesives
Neoprene Contact 5 5 gal, 53 gal 19% High performance contact adhesive. Sprayable. Fast drying.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Spray 54%
Low Clear Brush/Roll/Spray 15 sec–15 min Flammable 150°F Mist 504g/L
Spray 535g/L
High Light Yellow Spray 10–60 min Flammable 300°F Web 687g/L
High Light Yellow Brush/Roll 10–60 min Flammable 300°F Web 589g/L
Brush/Roll/Spray 356g/L
High Clear Spray 1–10 min Flammable 250°F Web 586g/L
Spray 54%
High Clear Spray 1–30 min Flammable 200°F Web <25%
Brush/Roll/Spray 79g/L
High Clear/Red 1–15 min Flammable 210°F Pebble
Spray 79g/L
935g/L
High Red/Clear Spray 10–60 min Non-flammable 240°F Web
907g/L
Blue/Light Orange/
High Co-Spray 2 min–2 hr Non-flammable 300°F Mist 37g/L
Neutral
Spray <55%
Medium Clear/Orange 30 sec–15 min Flammable 170°F Web 352g/L
Brush/Roll/Spray
563g/L
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Solids Weight
Product Available Format Percent (Approx.) Key Characteristics
SPECIALTY – Solvent Based Adhesives
Permanently tacky and repositionable. Long open time. Variable
Pressure Sensitive 72 Aerosol 15%
width lace spray pattern.
Repositionable 75 Aerosol 9% Adheres in seconds. Extra long tack range. Repositionable.
Fast tacking. One surface bonds. Variable width lace
Hi-Tack 76 Aerosol 13.5%
spray pattern.
5 gal Bonds polystyrene with no surface degradation. Fast grabbing
Polystyrene 78 19%
Aerosol and fast drying. Uniform spray pattern for fast and easy application.
Bonds polystyrene with no surface degradation. Extended tack
Polystyrene 78ET Large, Int and Jumbo Cylinder 17% time for long working time. Uniform spray pattern for fast and
easy application.
5 gal, 54 gal 27% Bonds polystyrene with no surface degradation. High temperature
Hi-Temp Polystyrene 78HT
Large, Int and Jumbo Cylinder 15% resistance. Can be used for roofing membrane attachment.
Rubber And Vinyl 80 Aerosol 13% High strength. High temperature resistance. Fast setting.
Fast drying for many plastic films. Resists fuels, water and oil.
826 Plastic Adhesive 1 qt, 5 gal 23%
Thin liquid.
847 High Performance Quick drying and flexible with fuel and oil resistance. Able
5 oz, 1 qt, 1 gal, 5 gal, 54 gal 36%
Rubber & Gasket Adhesive to reactivate with heat and solvent. Curable with heat.
847H High Performance High viscosity. Able to reactivate with heat and solvent.
5 gal 51%
Rubber & Gasket Adhesive Curable with heat.
1099 High Performance Fast drying and heat curable. Resists weathering, water, oil,
5 oz, 1 qt, 1 gal, 5 gal, 54 gal 34%
Plastic Adhesive plasticizer migration and aliphatic fuels.
1099L High Performance Sprayable version of 1099H. Fast drying and heat curable. Resists
5 gal, 54 gal 24%
Plastic Adhesive weathering, water, oil, plasticizer migration and aliphatic fuels.
1300 High Performance High immediate strength. Fast-drying and heat resistant for rubber
5 oz, 1 pt, 1 qt, 1 gal, 5 gal, 37%
Rubber & Gasket Adhesive and metal. Meets MIL-M-81288 and MMM-A-121.
1300L High Performance Lower viscosity for spraying. Fast-drying and heat resistant for rubber
1 qt, 1 gal, 5 gal, 54 gal 30%
Rubber & Gasket Adhesive and metal. Meets MMM-A-121.
1357 High Performance 5 oz, 1 pt, 1 qt, 1 gal, 5 gal, 54 gal Rapid build up to a very high strength bond for metal. Resists heat
25%
Contact Adhesive (Light Yellow only 5 gal and 55 gal) and continuous load stress. Meets MMM-A-121 requirements.
1357L High Performance Low viscosity. Resists heat and continuous load stress.
5 gal, 54 gal 18%
Contact Adhesive Meets MMM-A-121 requirements.
Clear and non-staining. Resists plasticizer migration for bonding
2262 Plastic Adhesive 1 qt, 5 gal 27%
many flexible vinyls. Fast tack.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
566g/L
Medium Clear Spray 1–15 min Flammable 190°F Web
62%
Gray-Green/
High Brush/Spray 10–30 min Flammable 300°F Web ≤582g/L
Light Yellow
Brush/Roll/
Medium Blue/Clear 15 min–8 hr Non-flammable – Mist 14g/L
Spray/Trowel
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
176
174
175
3M™ Polyurethane Sealant 560 moisture cures to a flexible seal/bond between exterior skins and metal
framework and between wood flooring and metal framework. Tensile strength up to 580 psi is enough
to replace mechanical fasteners in many situations.
177 178 5
sealants available in a variety of widths and cures completely in only 48 hours to a strong superior UV resistance that is ideal for
thicknesses. These are used for applications flexible bond/seal. Applications include: continuous exposure to sunlight. Applications
demanding high tack, aggressive adhesion, assembly above or below the waterline such include specialty vehicle roof seams and
weather resistance and flexibility. as, hull and stern joints, hull to deck seams, marine hardware assembly requiring superior
marine hardware and more. aesthetics.
46 179 180
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Convenience
meets extreme
bonding power.
Powerful Bonding Solutions
Help your customers successfully bond a variety of materials
with strength and speed for permanent, structural and
repositionable applications. Our double-sided bonding tapes
provide shear strength, conformability, surface adhesion and
temperature resistance.
293
3M Industrial Adhesives and Tapes | January 2017 Edition 67
3M Industrial Adhesives and Tapes
199
3M™
VHB™ Steel
Tape Framework
203
Mirrored
200 Ceiling Panel 201 202
Mirrored ceiling panels are held in place with For a heat resistant bond, 3M™ VHB™ Tapes With high holding power and long-term
3M™ VHB™ Tapes rather than screws. This bond and seal stainless steel trim to the glass reliability, 3M™ VHB™ Tape bonds dimensional
helps maintain a clean, smooth appearance oven door with strength enough to replace letters to a painted wall for indoor or outdoor
without distorting the reflective surfaces. mechanical fasteners. Door surface is smooth signage.
and attractive.
204
195
Bonding Tapes
205 206
• Enhance productivity
• Create innovative designs
207
209
210
5952P 45 (1.1) E
5952WF 45 (1.1) F
5962 62 (1.6) F
5962P 62 (1.6) E
5962WF 62 (1.6) F
Overhead stow bins, signage, kick
plates, galley modules, plastic and
eets FAR 25.853 (a)
M
300°F 200°F metal decorative trim, ceiling tile
5958FR 40 (1) F 12 sec vertical burn
(149°C) (93°C) stiffeners, mirror mounting, air duct
Appendix F, Part 1 (a) (ii)
spuds, floor and wall panel
attachment and clip attachment.
RP Tape Family
RP16 16 (0.4) A
RP16F 16 (0.4) F
RP25 25 (0.6) A
RP25F 25 (0.6) F
Gray, closed-cell acrylic
RP32 32 (0.8) A Multi-
foam carrier. Conformable. 250°F 200°F Panel bonding, stiffener attachment
purpose High High Med
RP32F 32 (0.8) F Good adhesion to many (121°C) (93°C) and trim attachment.
Acrylic
painted metals.
RP45 45 (1.1) A
RP45F 45 (1.1) F
RP62 62 (1.6) A
RP62F 62 (1.6) F
Liner Types: Relative Adhesion: Multi-purpose Acrylic: Bonds to a wide range of materials including metals, glass, and high and
A – 3 mil 54# Densified Kraft Paper HSE – High Surface Energy medium surface energy plastics and paints. Resists migration of plasticizers in vinyl substrates.
B – 5 mil Clear Polyethylene Film LSE – Low Surface Energy Modified Acrylic: Bonds to medium low surface energy paints and plastics, including many powder
C – 2 mil Polyester Film coated paints in addition to the substrates listed with the multi-purpose acrylic adhesive (except
D – 5 mil Red Polyethylene Film plasticized vinyl).
E – 4 mil 58# Polycoated Kraft Paper General Purpose Acrylic: Bonds to most higher surface energy substrates including metal, glass and
F – 5 mil Red Printed Polyethylene Film high surface energy plastics.
G – 3 mil Clear Polyethylene Film Low Temperature Acrylic: Bonds down to 32°F (0°C) compared to 50°F (10°C) for most acrylic
H – 5 mil Green PE Film adhesives. Bonds most high surface energy substrates including metal, glass and high surface energy
plastics.
Low Surface Energy: High performance synthetic adhesive bonds to many lower surface energy
substrates, including many plastics and powder coated paints, plus smooth general purpose substrates.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Bonding Tapes
4932 25 (0.6) A
White, closed-cell acrylic foam carrier. Low metal stiffeners to office
200°F 160°F
Good adhesion to polypropylene and Surface High High High desks and file cabinets.
(93°C) (71°C)
4952 45 (1.1) A many powder paints. Energy Bond polypropylene and
polystyrene.
4611 Tape Family
4646 25 (0.6) D
General Pre-powder coat paint
Dark gray, closed-cell acrylic foam carrier. 450°F 300°F
4611 45 (1.1) D Purpose High High Low applications. Hat channels
High temperature resistance. UL 746C. (232°C) (149°C)
Acrylic and stiffeners.
4655 62 (1.6) D
4622 Tape Family
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
*3M™ VHB™ Structural Glazing Tapes are only available for structural glazing applications approved by 3M Technical Service through select distributors.
Bonding Tapes
See key on page 70.
Vertical Seam
Panel Clip seam) Tape
Singapore
For quick permanent assembly of
cladding and curtain wall panels,
3M™ VHB™ Tapes provide an ideal Stainless Steel
combination of durability, Curtain Wall
218
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
224
Clear 3M™ VHB™ Tape permanently bonds aluminum letters to glass and appears almost invisible
from behind the pane.
Bonding Tapes
day. Bulky mechanical systems can be replaced with the incredible,
strong, long-lasting viscoelastic bond of 3M™ VHB™ Tape. Expand
design freedom and simplify manufacturing processes while
meeting the challenges of a dynamic market and look no further
228
than 3M™ VHB™ Tape.
Tape Temp.
Thickness w/o Resistance Relative Adhesion
Liner Liner Adhesive Min Days Solvent
Product mils (mm) Type Description Type Hr Weeks Resistance HSE LSE Application Ideas
5908 10 (0.25) G Bond and seal polycarbonate
5915 16 (0.4) F Black, closed-cell Modified 300°F 250°F lens over LCD. Bond and seal
High High Med plastic windows to pre-painted
5925 25 (0.6) F acrylic foam carrier. Acrylic (149°C) (121°C)
control panels/switch gear.
5952 45 (1.1) F Mount vinyl wiring ducts and
Multi- conduit channels. Electronic
RP16 16 (0.4) A Gray, closed-cell acrylic 250°F 200°F
purpose High High Med component and assembly
RP45 45 (1.1) A foam carrier. (121°C) (93°C) attachment.
Acrylic
3M™ Primers
Active
Product Solvent Ingredients VOCs Color Flashpoint Coverage Application Ideas
19m2/L (800 ft2/gal) based
Isopropyl
Less than 5.91 lb/gal 52°F on .002" wet coating thickness Promote better adhesion for bare
AP111 Alcohol Clear
5% by weight (708g/L) (11°C) depending on method of metals and painted surfaces.
(IPA)
application
Isopropyl
Less than 6.08 lb/gal 53°F 20–25 ft2 per 4 fl oz bottle
AP115 Alcohol Clear Promote better adhesion for glass.
1% by weight (728g/L) (12°C) (1.8–2.3m2 per 118mL bottle)
and Water
Promote better adhesion for a
Approx 6.3 lb/gal Clear Light
-4°F variety of plastic surfaces such
Primer 94 See SDS See SDS (755g/L) less H20 Yellow/Clear 600 ft2/gal (211m2/L)
(-20°C) as polyethylene, polypropylene,
and exempt solvents Dark Orange
ABS and PET/PBT blends.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Suggested Uses
• RV trailer and roofs • Vent stacks/windows
• Metal enclosures • Gutters and downspouts
• Awnings • Skylights
• Trailer home roofs • Outdoor signs/displays
• Metal storage buildings • Leak patching and repairs
16
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Release Liner
Pressure Sensitive
Adhesive
Foam Carrier
Pressure Sensitive
Bonding Tapes
Adhesive
230
To replace screws and liquid adhesives, 3M™ Multipurpose Mounting Tape 4016 bonds immediately
229
to many indoor surfaces, even permanently mounting a plastic soap dispenser to a mirror.
231 232
pe
Ta
am
233 Fo
234 235
3M™ Double Coated Urethane Foam Tapes bond plastic signs to painted 3M™ Double Coated Polyethylene Foam Tapes with high tack adhesive
cinder block. The foam fills gaps between irregular surfaces. Various bond foam spacers between the planes of a 3-dimensional P.O.P. display.
foam thicknesses are available for surface conformance based on the
degree of roughness.
Polyethylene
4462 31 (0.8) White or black, closed-cell Attach hooks, wire clips and racks.
158°F 120°F
B polyethylene foam carrier. 745 Mount retail shelf price channels.
(70°C) (49°C) Med High Low
4466 62 (1.6) High tack adhesive. Mount pen holders.
Acrylic
Liner Types:
A – 3 mil 62# Densified Kraft paper – Green plaid
B – 3 mil Densified Kraft paper – White
C – 4 mil 58# Polycoated Kraft paper – Tan
D – 2 mil Polyester film – Clear
E – 3 mil Densified Kraft paper – Tan
Relative Adhesion:
HSE – High Surface Energy
LSE – Low Surface Energy
15
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Bonding Tapes
237 238 239
With differential adhesive, the silicone 3M™ Double Coated Tape 410M is the quick, For precise fit, 3M™ Double Coated Tape
adhesive side of 3M™ Double Coated Tape convenient way to bond golf club grips to is pre-applied to foam gasketing materials
adheres to a silicone rubber keypad. Acrylic shafts. Adhesive sets up fast and bonds firmly and then die-cut to size. This helps increase
adhesive side adheres to a plastic base. for long-lasting performance. dimensional stability of the part to facilitate
assembly.
Temp.
Tape Liner Adhesion Range
Cal. Carrier Caliper Master HSE LSE Chem. Low High
Product Description/Application Ideas (mils) Type Type (mils) Size Specs Metal Plastic Plastic Foam Resist. (°F) (°F)
200MP/300LSE (Differential Adhesive)
58#
Very thin double-coated tape polyester PCK/ 4.2/ 48" x 60
93005LE 2.0 PET –
tape with good anti-lifting properties. 83# 6.2 yd
PCK
58# 54" x
93010LE 3.9 PET 4.2 – 9 9 10 1 8 -40 300
PCK 180 yd
High adhesion to polypropylene and LSE
58# 54" x
93015LE plastics for excellent graphic appearances. 5.9 PET 4.2 –
PCK 180 yd
Good chemical/humidity resistance.
58# 54" x
93020LE 7.9 PET 4.2 –
PCK 180 yd
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Temp.
Tape Liner Adhesion Range
Cal. Carrier Caliper Master HSE LSE Chem. Low High
Product Description/Application Ideas (mils) Type Type (mils) Size Specs Metal Plastic Plastic Foam Resist. (°F) (°F)
300 (High Strength Acrylic)
55# 48" x 108
444 Foam lamination. Gasket attachment. 3.9 PET 3.2 –
DK yd
7 9 9 9 6 -40 250
58# 48" x 108
444PC Foam lamination. Gasket attachment. 3.9 PET 4.2 –
PCK yd
300MP (High Tack Acrylic)
Thin nonwoven carrier for dimensional
Non- 58# PCK 48" x 180
99786 stability and improved handling. 5.5 4.2 –
woven Printed yd
Temperature resistance up to 300°F.
Non- 58# PCK 54" x 180
99786NP Same as 9786 except an unprinted liner. 5.5 4.2 –
woven Unprinted yd 7 7 8 9 7 -40 250
General purpose tape with improved 58# 54" x
9832 4.8 PET 4.2 –
temperature resistance. PCK 250 yd
58# 54" x
9832HL Same as 9832 except with a heavier liner. 4.8 PET 6.2 –
PCK 250 yd
340 (High Tack Acrylic)
High tack acrylic adhesive with good 55# 54" x 180
9456 5.0 Tissue 3.2 –
adhesion to many plastics. DK yd
55# 54" x
9824 3.1 PET 3.2 –
Foam lamination. DK 250 yd
6 6 5 4 8 -40 180
Gasket attachment. 55# 54" x
9828 4.0 PET 3.2 –
DK 250 yd
High tack acrylic adhesive with good 74# 54" x
9828PC 4.0 PET 5.6 –
adhesion to many foams. PCK 250 yd
350 (High Performance Acrylic)
High performance with good chemical 61.5 48" x 108
9500PC 5.6 PET 4.5 –
resistance. PCK yd
9 10 10 9 8 -40 450
Same as 9500PC with an extensible kraft Extensible 48" x 108
3028EK 5.6 PET 5.5 –
liner which facilitates narrow slitting. Kraft yd
375 (High Performance Double Coated)
Glassine
54" x 750
9086 Easy tearing, easy handling. 7.5 Tissue Black 3.0 – 250
yd
Logo
High High Med Low Good -10
Glassine
54" x 750
9087 Thick adhesive to bond rough surfaces. 10.2 PVC Green 3.0 – 185
yd
Logo
400 (Acrylic Adhesive)
60# 48" x 108
415 4.0 PET 4.0 –
DK yd
Splice papers, films and foils. 5 5 5 5 5 -60 250
Clear 60# 27" x 360
9576 4.0 4.0 –
PP DK yd
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
55#
Clear, thin PET carrier. Aggressive and 54" x
9737 3.5 PET DK 3.5 –
versatile splicing tape. 180 yd
White
5 5 2 5 7 -10 300
Non- 55#
Clear, non-woven tissue carrier. 54" x
9738 4.3 woven DK 4.3 –
Aggressive and versatile splicing tape. 180 yd
tissue White
Clear, high peel, tack and shear
55# 54" x
Bonding Tapes
9740 strength. Performance grade 3.5 PET 3.5 – 6 6 2 3 6 10 425
DK 180 yd
splicing tape for corrugators.
Clear, thick, super aggressive tape.
55# 54" x
9741 Adheres to a wide variety of substrates 6.5 PET 6.5 – 7 7 3 7 5 -40 200
Glassine 180 yd
for splicing applications.
60# 54" x
9816L 3.5 –
Kraft 200 yd
General purpose, high tack, 74# 54" x
9816M 3.5 PET 3.5 – 8 8 7 7 3 -40 150
rubber-based adhesive. Kraft 200 yd
14 pt. 54" x
9816H 3.5 –
Board 200 yd
60# 54" x
9817L 3.5 – 8 7 6 7 3
Kraft 200 yd
Exposed side is acrylic, liner side is
74# 54" x
9817M rubber-based. Excellent quick stick and 3.3 PET 3.5 – -40 175
Kraft 200 yd
adhesion to high and low energy surfaces. 8 8 7 6 3
14 pt. 54" x
9817H 3.5 –
Board 200 yd
Specialty Differential Rubber/Acrylic
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Temp.
Tape Liner Adhesion Range
Cal. Carrier Caliper Master HSE LSE Chem. Low High
Product Description/Application Ideas (mils) Type Type (mils) Size Specs Metal Plastic Plastic Foam Resist. (°F) (°F)
400/1000* (Differential Adhesive)
78#
9415PC Differential adhesive; polyester film carrier. 2 PET 6.0 48" x 216 yd – 5 5 5 4 5
PCK
70#
9416 Differential adhesive; tissue carrier. 1 Tissue 5.6 48" x 216 yd – 3 1 1 – 2 -20 150
PCK
Reverse wound ATG version of 9416 on 70# Up to 3/4" W
928ATG 1 Tissue 5.6 – 3 1 1 – 2
1" core. Used with ATG700 Applicator. PCK Up to 36 yd L
420/1050* (Differential Adhesive)
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Release Liner
Pressure
Sensitive
Adhesive
244
Bonding Tapes
With high cohesive strength, 3M™ Adhesive 200MP bonds aggressively with excellent temperature
resistance. Meets the non-fogging specifications of the automotive industry.
243
For bonding flexible vinyl in such applications 3M Laminating Adhesive 300LSE is the solution
™
3M Adhesive Transfer Tapes provide
™
as door gaskets, 3M™ Adhesive Transfer Tape for low energy surfaces such as polyolefins and conformability in a variety of foam laminating
F9465PC resists the effect of plasticizers that powder coat paint. Graphics hold securely and applications. The acrylic adhesive also provides
tend to migrate from the vinyl. stand up to tough environmental conditions. high shear strength and good environmental
aging properties.
3M™ Adhesive Transfer Tape 465 has the grab 3M™ Adhesive Transfer Tape 467MP is used to For graphic beauty, 3M™ Acrylic Adhesive 100
strength for many printing splices, including laminate metal foil to a circuit board to reduce attaches graphics in closed environments. With
flying splices, zero speed and manual overlap. interference on electronic circuitry. low odor, reduced outgassing and low fogging, it
Can be used with a variety of paper grades. is used extensively in the automotive, aerospace
and appliance industries.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Temp.
Adhesive Liner Adhesion Range
Caliper Caliper Master HSE LSE Chem. Low High
Product Description/Application Ideas (mils) Type (mils) Size Specs Metal Plastic Plastic Foam Resist. (°F) (°F)
100MP* (High Performance Acrylic)
High performance industrial joining 58# 60" x
F9460PC 2 4.2 UL
and metal fabrication. PCK 180 yd
High performance industrial joining 58# 60" x
F9469PC 5 4.2 UL 10 7 1 2 10 -40 500
and metal fabrication. PCK 180 yd
High performance industrial joining 58# 60" x
F9473PC 10 4.2 UL
and metal fabrication. PCK 180 yd
200MP (High Performance Acrylic)
Same as 467MP with a paper
58# 54" x
467MC MicroChannel liner to aid in bubble 2 4.2 –
PCK 180 yd
and wrinkle free graphic attachment.
Same as 467MP with a polyester
54" x
467MCF MicroChannel liner to aid in bubble 2 PET 4.2 –
180 yd
and wrinkle free graphic attachment.
Graphic attachment and general
58# 48" x UL
467MP industrial joining. Industry standard. 2 4.2
PCK 180 yd MH
60" width master also available.
Polyester liner for rotary processing 54" x
467MPF 2 PET 2.0 UL
of graphic and die cut parts. 180 yd
Same as 468MP with a paper
58# 54" x
468MC MicroChannel liner to aid in bubble 5 4.0 –
PCK 180 yd
and wrinkle free graphic attachment.
Same as 468MP with a polyester 10 9 1 3 9 -40 400
54" x
468MCF MicroChannel liner to aid in bubble 5 PET 4.0 –
180 yd
and wrinkle free graphic attachment.
Industry standard for graphic attachment
58# 48" x UL
468MP and die cut parts. 60" width master 5 4.2
PCK 180 yd MH
also available.
54" x
468MPF Thicker version of 467MPF. 5 PET 2.0 UL
180 yd
Same as 467MP on heavy, lay-flat liner for
83# 54" x
9667MP kiss-cutting. 48" width master also 2 6.2 UL
PCK 180 yd
available.
Same as 468MP on heavy, lay-flat liner. 83# 54" x UL
9668MP 5 6.2
48" width master also available. PCK 180 yd MH
94# 60" x
9668MPL Better lay-flat properties. 5 7.0 –
PCK 180 yd
220 (Industrial Acrylic)
Economical attachment of graphics
58# 48" x
9502 and industrial joining. 60" width 2 4.2 UL
PCK 180 yd
master also available.
Thicker version of 9502 for textured 58# 48" x
9505 5 4.2 UL
surfaces. 60" width master also available. PCK 180 yd 8 7 1 2 8 -40 350
Double-linered laminating adhesive 58/58# 48" x
9552 2.3 4.2 UL
version of 9502. PCK 360 yd
Double-linered laminating adhesive 58/58# 48" x
9555 4.9 4.2 UL
version of 9505. PCK 360 yd
*Products in this platform are 3M™ VHB™ Tapes offering our highest strength.
MH meets Mil-P-19834B Type I.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Temp.
Adhesive Liner Adhesion Range
Caliper Caliper Master HSE LSE Chem. Low High
Product Description/Application Ideas (mils) Type (mils) Size Specs Metal Plastic Plastic Foam Resist. (°F) (°F)
290 (Low Outgassing Acrylic)
Ultra-clean adhesive for low outgassing 54" x
501FL 1 PET 2.0 –
applications. 180 yd
9 7 1 2 9 -40 450
Ultra-clean adhesive for low outgassing 54" x
502FL 2 PET 2.0 –
applications. 180 yd
300 (High Strength Acrylic)
Attach gaskets and a variety of industrial 60# 48" x
927 2 3.5 –
foam materials. DK 180 yd
60# 48" x
950 Thicker version of 927. 5 3.5 UL
DK 180 yd
Thicker version of 927 with extensible 78# 48" x
950EK 5 6.0 –
Kraft liner. EK 180 yd
For performance-engineered labels. 55# 48" x
992U 2 3.2 UL
UV indicator in adhesive. DK 180 yd
Thin, high tack adhesive for rotary 55# 54" x
9458 1 3.2 UL
processing HSE and LSE parts. DK 360 yd
White version of laminating 55# 48" x
9459W 1.5 3.2 UL
adhesive 9459S. DK 360 yd
7 9 9 9 6 -40 250
60# 48" x UL
9471 For smooth LSE plastics. 2 3.5
DK 180 yd MH
5.0 mil version of 9471; for 60# 48" x UL
9472 5 3.5
textured surfaces. DK 180 yd MH
A 3.5 mil version of 9471 on a heavy, 83# 48" x
9653 3.5 6.2 UL
lay-flat liner for kiss-cutting. PCK 180 yd
Heavier linered version of 9471 for 83# 48" x UL
9671 2 6.2
easy handling, lay-flat properties. PCK 180 yd MH
Heavier linered version of 9472 for 83# 48" x
9672 5 6.2 UL
Bonding Tapes
easy handling, lay-flat properties. PCK 180 yd
83# 48" x UL
9673 Same as 9671 with unprinted liner. 2 6.2
PCK 180 yd MH
300FR (Flame Retardant)
83# 60" x
9372W Flame retardant. Moisture stable liner. 2 6.2 UL
PCK 180 yd
55# 60" x
9372DKW Flame retardant. Rotary diecuttable liner. 2 3.2 UL 8 9 9 9 6 -40 250
DK 180 yd
83# 60" x
9375W Flame retardant. Moisture stable liner. 5 6.2 UL
PCK 180 yd
*Products in this platform are 3M™ VHB™ Tapes offering our highest strength.
MH meets Mil-P-19834B Type I.
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Temp.
Adhesive Liner Adhesion Range
Caliper Caliper Master HSE LSE Chem. Low High
Product Description/Application Ideas (mils) Type (mils) Size Specs Metal Plastic Plastic Foam Resist. (°F) (°F)
300LSE (Low Surface Energy Acrylic)
Film linered version of 9453LE for 54" x
9453FL 3.5 PET 2.0 UL
rotary processing. 180 yd
A 3.5 mil version of 9471LE for application
58# 54" x
9453LE to rough surfaces. 48" master width 3.5 4.2 UL
PCK 180 yd
available.
Film linered version of 9471LE for 54" x
9471FL 2.3 PET 2.0 UL
rotary processing. 180 yd
Bonds graphics to powder coatings, 58# 54" x
9471LE 2.3 4.2 UL
LSE plastics and oily materials. PCK 180 yd
A 5 mil version of 9471LE with film liner 54" x 9 10 10 1 7 -40 300
9472FL 5.2 PET 2.0 UL
for textured surfaces. 180 yd
Thicker adhesive for textured LSE plastics 58# 54" x
9472LE 5.2 4.2 UL
and powder coatings. PCK 180 yd
Heavy linered 9453LE for easy handling 83# 54" x
9653LE 3.5 6.2 UL
and lay-flat properties. PCK 180 yd
Heavy linered 9471LE for easy handling 83# 54" x
9671LE 2.3 6.2 UL
and lay-flat properties. PCK 180 yd
Heavy linered 9472LE for easy handling 83# 54" x
9672LE 5.2 6.2 UL
and lay-flat properties. PCK 180 yd
300MP (High Tack Acrylic)
Resists fogging for automotive interior 58# 60" x
6035PC 5 4.2 –
fabric joining applications. PCK 180 yd
Heavy linered version of 6035PC for easy 83# 60" x
6035PL 5 6.2 –
handling, lay-flat properties. PCK 180 yd
Low fogging. Automotive fabric and 58# 60" x
6038PC 8 4.2 –
carpet attachment. PCK 180 yd
Low fogging. For rough embossed 7 7 8 8 7 -40 250
83# 60" x
6038PL surfaces with heavy liner for steel rule 8 6.2 –
PCK 180 yd
die-cutting.
9772WL 2
9773WL Provides excellent bond to various 3 96# 60" x
7.0 –
9774WL fabricated foams, fabrics and substrates. 4 PCK 180 yd
9775WL 5
320 (High Tenacity Acrylic)
Designed for use with 3M™ Label 55# 54" x
9447 1 3.2 – 5 5 1 1 5 -60 250
Component Systems. DK 360 yd
350 (High Performance Acrylic)
Excellent temperature and solvent
55# 48" x
9442 resistance; high bond to low surface 2 3.2 UL
DK 180 yd
energy substrates.
55# 48" x
9445 Thicker version of 9442. 5 3.2 UL
DK 180 yd
High tack and shear strength; excellent 58# 48" x
9482PC 2 4.2 UL
adhesion to plastics and foams. PCK 180 yd 9 10 10 9 8 -40 450
Thicker version of 9482PC with an 78# 48" x
9485EK 5 6.0 –
extensible Kraft liner. EK 180 yd
58# 48" x
9485PC A 5 mil version of 9482PC. 5 4.2 UL
PCK 180 yd
Heavy linered version of 9485PC for easy 83# 48" x
9675 5 6.2 –
handling, lay-flat properties. PCK 180 yd
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Temp.
Adhesive Liner Adhesion Range
Caliper Caliper Master HSE LSE Chem. Low High
Product Description/Application Ideas (mils) Type (mils) Size Specs Metal Plastic Plastic Foam Resist. (°F) (°F)
400 (Acrylic Adhesive)
High tack and excellent adhesion to most 60# 48” x
463 2 3.5 –
paper stocks. For automatic dispensing. DK 180 yd
Same as 463, but with easy liner release 60# 48" x
465 2 3.5 –
for manual or hand application. DK 180 yd
Adhesive with long term stability,
excellent outdoor performance and UV 5 5 5 4 5 -60 250
55# 54" x
9457 resistance. Adhesive 400 is best if 1 3.2 UL
DK 360 yd
necessary to apply
at cooler temperatures.
58# 48" x
9665 Thicker version of 9457. 2 4.2 –
PCK 180 yd
420 (Acrylic Adhesive)
High tack; can be applied in temperatures 58# 54" x
F9752PC 2 4.2 –
as low as 32°F (0°C). PCK 360 yd
7 7 8 4 6 -40 300
Thicker version of F9752PC for 58# 54" x
F9755PC 5 4.2 –
textured surfaces. PCK 360 yd
430 (Acrylic Adhesive)
60# 48" x
9497 Pink tinted high temperature splicing tape. 2 3.5 –
DK 360 yd
6 6 5 4 5 -40 350
60# 48" x
9499 Transparent version of 9497. 2 3.5 –
DK 360 yd
Specialty Acrylic
Jet fuel and hydraulic fluid resistant 48" x
9379 2 PET 2 MH*
adhesive transfer tape. 200 yd
9 8 1 2 9 -40 350
48" x
9380 Thicker version of 9379. 5 PET 2 MH*
200 yd
58# 54" x
F9465PC Vinyl plasticizer resistant adhesive. 5 4.2 –
Bonding Tapes
PCK 360 yd
10 10 7 5 5 -40 200
58# 54" x
F9467U Vinyl plasticizer resistant adhesive. 3.5 4.2 –
PCK 180 yd
Silicone
Silicone attachment. Silicone linered for White 48" x
91022 2 2 – 9 8 7 6 10 -40 500
easier processing. PET 180 yd
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
plastic and more. Scotch® ATG Applicator 700 with Scotch® Scotch® ATG Applicator
ATG Adhesive Transfer Tape 924 makes fast 3662 for 2" wide tape
Leader for fast, work of folder assembly. Pressure sensitive
easy loading
adhesive bonds immediately and the folder
Pressure Sensitive pocket is ready to hold contents.
Adhesive
256
Release Liner
229
*3M Brand Relative Adhesion: HSE – High Surface Energy; LSE – Low Surface Energy
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Bonding Tapes
Tape Temperature Relative
Thickness Resistance Adhesion
w/o liner Min Days Solvent
Product mils (mm) Liner Type Description Hr Weeks Resistance HSE LSE Application Ideas
340
Coated papers and low surface energy (LSE) plastics.
2 62# DK White High tack; 180°F 150°F
466XL Med High High Overnight envelopes. Features an end-of-roll indicator
(0.05) with Black Print Permanent (82°C) (65°C)
tab for automated dispensing.
400
Seal flaps on overnight envelopes. Pressure sensitive
2 60# DK Tan edging on business forms. General commercial joining
465XL
(0.05) with Green Print applications. For attaching materials that require more
adhesive thickness. Larger outsert attachments.
78# Extensible
1 Pharmaceutical outsert attachment. For applications
450EK Kraft White w/o 250°F 180°F
(0.025) General purpose Med Med Low requiring a more tear resistant liner.
Print (121°C) (82°C)
1 60# DK Tan Pharmaceutical outsert attachment. General paper
450XL
(0.025) with Green Print attachment.
Seal flaps on polybags and envelopes. Pressure
1 40# DK White
920XL sensitive edging on business forms, literature, photos,
(0.025) with Red Print
posters and labels.
1 40# DK White 180°F 150°F Economical alternative for general paper-to-paper
9926XL General purpose Med Med Low
(0.025) with Red Print (82°C) (65°C) applications.
600
P.O.P. displays. Difficult splicing applications, shelf
4 60# DK tan High tack to LSE 150°F 120°F
9934XL Med High High talkers, price tags, polyethylene foam bonding. Indirect
(0.10) without Print materials (65°C) 49°C)
food-contact applications.1 High tack to LSE materials.
760
Heavy-duty sealing. Mounting of promotional items.
6 62# DK White High tack, double 150°F 120°F
476XL Med High High Core starting. Closure of overnight boxes, tubes and
(0.16) with Red Print coated film (65°C) 49°C)
envelopes. Indirect food-contact applications.1
770
Tissue reinforced; General mounting. P.O.P. items. Attaching tags and
2.5 43# DK White High initial 150°F 100°F labels. Core starting. Permanent bonding paper-to-
9925XL2 Low Med Med
(0.065) with Black Print adhesion to a wide (65°C) 41°C) paper, business forms, traffic tickets, novelty items
variety of materials and literature. Indirect food-contact applications.1
Relative Adhesion:
1 – FDA acceptable dry ingredients listed as indirect food-contact additives when used in food packing with minimal opportunity for exposure.
HSE – High Surface Energy
2 – Non-liner side is adhesive coated full width.
LSE – Low Surface Energy
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
Notes:
Supporting your
designs behind
the seams.
Powerful Fastening Solutions
3M™ Reclosable Fasteners provide secure fastening with
easy access and enhanced gripping for a wide range of
applications. Weather-resistant single coated foam tapes
are practical solutions that protect against moisture, dust,
vibration and impact, and remain flexible.
39 266
Secure plastic signs to window glass. Anchor vehicle accessories to dashboard.
267 268 27
Attach elevator control panel to interior wall. Fasten ceiling panels to interior for future access. Attach access panels to industrial, electronic
and electrical equipment.
General Industrial
Aerospace & Rail
Metals (Al & SS)
Stem
Density Temperature
Glass
(per Engaged Resistance Indoor/
Product sq/in) Adhesive Color 3M Liner Thickness °F (°C) Outdoor
SJ3540 250
White,
0.23 in 120
SJ3541 400 Rubber Black 5 mil (0.13mm) Indoor
(5.7mm) (49)
Polyolefin
SJ3542 170
SJ3550 250
Clear,
White 0.23 in 200 Indoor/
SJ3551 400 Black 4 mil (0.10mm)
Acrylic (5.7mm) (93) Outdoor
Polyolefin
SJ3552 170
Clear,
White 0.23 in 200 Indoor/
SJ3558 250 Clear* 4 mil (0.10mm)
Acrylic (5.7mm) (93) Outdoor
Polyolefin
SJ3560 250
Clear,
Clear 0.23 in 220 Indoor/
SJ3561 400 Clear 4 mil (0.10mm)
Acrylic (5.7mm) (104) Outdoor
Polyolefin
SJ3562 170
SJ3550CF 250
Clear,
Clear 0.23 in 220 Indoor/
SJ3551CF 400 Black 4 mil (0.10mm)
Acrylic (5.7mm) (104) Outdoor
Polyolefin
SJ3552CF 170
SJ3870 250
Red,
Modified 0.24 in 140 Indoor/
SJ3871 400 Black 4.5 mil (0.11mm)
Acrylic (6.1mm) (60) Outdoor
Polyolefin
SJ3872 170
Low
Surface Brown, 0.16 in 120 Indoor/
SJ3782 250 Black
Energy 83# Polykraft (4.1mm) (49) Outdoor
Acrylic
SJ3440 250
0.15 in 220 Indoor/
SJ3441 400 None Black No Liner
Specialty Technologies
(3.86mm) (104) Outdoor
SJ3442 170
*Clear fastener utilizes a white adhesive giving the product a white appearance **Single thickness; not engaged †No adhesive
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
270
Hook
with pressure sensitive adhesive
271 272
Attach cushioning panels in an ambulance or bus. Sew to the fabric and leather of jackets and gloves.
General Industrial
Aerospace & Rail
Indoor/Outdoor
Metals (Al & SS)
Closure Life
°F (°C)
Glass
Product Engaged
Product Type Adhesive Material Liner Description Thickness
Best
Low Profile/Thin
SJ3506 Hook Polypropylene Brown
0.034" 158 Indoor/
Acrylic 25 #83 Polykraft
(0.84mm) (70) Outdoor
SJ3507 Loop Polyester Green Print
Back-to-Back Polypropylene/ 0.053" 200
SJ3000 None 10 None Indoor
Hook and Loop Nylon (1.3mm) (93)
Specialty Technologies
Flame Resistant
SJ3519FR Hook White, 3 mil (0.08mm)
Flame 0.14" 158
5,000 FR Nylon Polyethylene Film Indoor
Resistant (3.6mm) (70)
SJ3518FR Loop 3M Red Print
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
To help prevent light leakage around a sign In outdoor mailboxes, strips of 3M™ Vinyl Foam
perimeter, 3M™ Vinyl Foam Tape 4726 attaches Tape 4504 helps seal the inside from rain and
Release Liner securely on contact. dirt. Vinyl provides excellent aging characteristics
and remains flexible.
Pressure Sensitive
Adhesive
Foam Carrier
280
4314 Charcoal Gray Soft conformable, low density foam 0.250 (6)
for sealing out air, dust and light
250°F 150°F
4317* Charcoal Gray when compressed 30%. Used to help 430 Acrylic 0.375 (9.5) 2 (32) 25 (170) 0.3 (2.1) 5
(121°C) (66°C)
damp sound and absorb vibration in
4318 Charcoal Gray electronics. 0.125 (3)
Vinyl
4504* Black Durable, flexible, closed cell vinyl 0.250 (6) 20 (320) 90 (620)
foams with excellent aging character-
4508* Black istics. Weather resistant. Application 430 Acrylic 0.125 (3) 20 (320) 100 (690) 4 (27.6) 15
ideas include dust
4516* Black and moisture seal. 0.062 (1.5) 25 (400) 130 (895)
250°F 150°F
(121°C) (66°C)
4714* Black 0.250 (6) 14 (225) 75 (515) 2 (13.8) 5
Note: The technical information and data on these pages should be considered representative or typical only and should not be used for specification purposes.
3M™ Performance Label Materials with Structured Adhesive – With unique microchannels
• 3M Bumpon Protective Products
™ ™
throughout the structured adhesive, air flows freely from between the label adhesive and
• And more substrate. Hand-applied large labels go on smoothly and stay that way permanently without
unsightly wrinkles and bubbles.
Specialty Technologies
For permanent attachment of die-cut durable Dimensionally-stable 3M™ Double Coated Tapes 3M converters can slit 3M™ Masking Tapes
graphics, 3M™ Low Surface Energy (LSE) are pre-applied to foam gasketing material to specified widths and roll lengths, as well
Acrylic Adhesive 300 bonds on contact and and die-cut to precise shape and size for fast, as die-cut to unique shapes for specialized
stays tight on low surface energy plastics, easy application. applications.
powder coated paints, and lightly oiled metals.
For hundreds to thousands of openings For a little touch of quiet and skid resistance From the 150,000 possible combinations
and closings, 3M converters customize on a PDA or other small product, custom of adhesives, facestocks, overlaminates and
3M™ Reclosable Fasteners to meet exact 3M™ Bumpon™ Protective Products are scaled liners, 3M has many choices for durable labels
customer requirements for form, fit, mating for the design. Adhesive is formulated to hold requiring UL and/or RoHS compliance.
strength, and liner. even a small bonding surface.
Numerical Index
Product Page Product Page Product Page Product Page
Numerical Index
Product Page Product Page Product Page Product Page
3M™ Dual Lock™ Reclosable 3M™ Hot Melt Adhesives, Applicators 3M™ Removable/Repositionable Tapes 53382........................................................... 45
Fasteners (cont.) and Accessories 665................................................................ 82 87979........................................................... 45
9725..............................................................49 666............................................................... 82
SJ3552.........................................................93 87982........................................................... 45
9726..............................................................49 9415PC........................................................ 82
SJ3552CF...................................................93 97331............................................................ 45
9727..............................................................49 9416.............................................................. 82
SJ3558........................................................93 98073........................................................... 45
9785.............................................................49 9425............................................................. 82
SJ3560........................................................93
9913..............................................................49 3M™ Scotch-Weld™ Instant Adhesives
SJ3561.........................................................93 401M............................................................ 82
EC100...........................................................38
9916..............................................................49 410M............................................................. 82
SJ3562........................................................93 EC2500.......................................................38
9917..............................................................49 928ATG....................................................... 82
SJ3782.........................................................93 EC40............................................................38
9921..............................................................49 9425HT........................................................ 82
SJ3870........................................................93 EC5...............................................................38
9922.............................................................49
SJ3871..........................................................93 3M™ Scotch-Weld™ ECI Gel.........................................................38
9929.............................................................49
SJ3872.........................................................93 Anaerobic Adhesives LO100...........................................................38
9940.............................................................49 HP42.............................................................. 41
SJ4570........................................................93 LO1000........................................................38
9946.............................................................49 HP45.............................................................. 41
SJ4575.........................................................93 PR Gel..........................................................38
Bench Mount..............................................49 PS65.............................................................. 41
SJ4580........................................................93 PR100...........................................................38
Bench Nozzle Assembly..........................49 PS67.............................................................. 41
3M™ Extended Liner Tapes PR1500.........................................................38
Foot Pedal Assembly................................49 PS77............................................................... 41
450EK..........................................................89 PR40.............................................................38
Heavy-Duty Benchstand.........................49 TL22............................................................... 41
450XL...........................................................89 PR600..........................................................38
Hot Melt Applicator AE II........................49 TL42............................................................... 41
465XL...........................................................89 SI Gel............................................................38
Hot Melt Applicator Pneumatic TL43............................................................... 41
466XL...........................................................89 PG II with Speedloader............................49 SI100.............................................................38
TL62.............................................................. 41
476XL...........................................................89 Hot Melt Applicator TC...........................49 SI1500..........................................................38
TL71................................................................ 41
920XL...........................................................89 Hot Melt Applicator TC with SF20.............................................................39
Quadrack Converter.................................49 TL72............................................................... 41
9925XL2......................................................89 CA100..........................................................39
Low Melt Applicator AE II LT.................49 TL77............................................................... 41
9926XL........................................................89 CA4...............................................................39
Low Melt Applicator LT...........................49 TL90.............................................................. 41
9934XL........................................................89 CA40............................................................39
Low Melt Applicator LT with AC649......................................................... 42
3M Extreme Sealing Tapes
™ CA40H.........................................................39
Quadrack Converter.................................49 GM10............................................................ 42
4411G............................................................ 76 CA5...............................................................39
Low Melt Applicator Pneumatic GM18............................................................ 42
4411N............................................................ 76 PG II LT with Speedloader......................49 CA50 Gel....................................................39
GM74............................................................ 42
4411B............................................................. 76 Quadrack Converter.................................49 CA7...............................................................39
RT09............................................................. 42
4412N........................................................... 76 TC and LT Palm Trigger...........................49 CA8...............................................................39
RT38............................................................. 42
Valve Assembly Kit....................................49 CA9...............................................................39
3M Hook and Loop
™
RT41.............................................................. 42
Reclosable Fasteners Variable Applicator EC.............................49 MC100.........................................................39
RT48............................................................. 42
SJ3000........................................................95 3731................................................................ 51 RT5000B.....................................................39
SJ30H..........................................................95 3738............................................................... 51 3M™ Scotch-Weld™ EPX™ SF100...........................................................39
Applicators and Nozzles
SJ30L...........................................................95 3747............................................................... 51 AC09............................................................40
3M™ Scotch-Weld™ EPX™
SJ3401.........................................................95 3748............................................................... 51 Manual Applicator 200mL...................... 43 AC77.............................................................40
SJ3402........................................................95 3750.............................................................. 51 3M™ EPX™ Metal AC79............................................................40
SJ3418FR....................................................95 3762............................................................... 51 Applicator 50mL........................................... 43 AC113............................................................40
SJ3419FR....................................................95 3764............................................................... 51 3M™ Scotch-Weld™ EPX™ AC452..........................................................40
Plus II Applicator........................................ 43
SJ3506........................................................95 3779............................................................... 51 3M™ Scotch-Weld™ PUR
3M™ EPX™ Pneumatic
SJ3507........................................................95 3789.............................................................. 51 Applicator 50mL....................................... 43 Adhesive Systems
SJ3518FR....................................................95 3792............................................................... 51 EZ250015....................................................36
3M™ Concrete Repair
SJ3519FR....................................................95 3797............................................................... 51 8.4 oz Cartridge Nozzles........................ 44 EZ250060..................................................36
SJ3522.........................................................95 3748 VO........................................................ 51 3M™ EPX™ 200, 400mL EZ250120....................................................36
Manual Applicator..................................... 44 TE015...........................................................36
SJ3523.........................................................95 3750LM........................................................ 51
3M™ EPX™ 400mL TE030..........................................................36
SJ3526N.....................................................95 3762LM........................................................ 51 Pneumatic Applicator............................... 44
SJ3527N......................................................95 3776LM........................................................ 51 TE100...........................................................36
3M™ EPX™ 490mL Manual
SJ3530........................................................95 3792LM........................................................ 51 Applicator.................................................... 44 TE200..........................................................36
SJ3531.........................................................95 3794 Hi Tack PSA...................................... 51 3M™ EPX™ 490mL 3M™ Scotch-Weld™ PUR Applicator.......37
SJ3571..........................................................95 Pneumatic Applicator............................... 44 3M™ Scotch-Weld™ PUR Preheater...... 37
3798LM........................................................ 51
SJ3572.........................................................95 3M™ Scotch-Weld™ EPX™ 3M™ Scotch-Weld™ PUR Repair
3M™ Hot Melt Spray Adhesives Mixing Nozzle............................................ 44 Kits and Replacement Parts................... 37
SJ60H..........................................................95 6111................................................................. 51 3M™ Scotch-Weld™ EPX™ 3M™ Scotch-Weld™ PUR System
SJ60L...........................................................95 6111HT........................................................... 51 Pneumatic Applicator 200mL................ 44 Accessories for hands-free
Standard Caulk Gun................................. 44 dispensing .................................................. 37
6116................................................................ 51
Index
3M, Bumpon, Dual Lock, EPX, Fastbond, Quadrack, Scotch-Seal, Scotch-Weld, Super 77, VHB and Weatherban
are trademarks of 3M Company.
Scotch is a registered trademark of 3M Company.
LEED® is a registered trademark of the United States Green Building Council (USGBC).