Beruflich Dokumente
Kultur Dokumente
Technical Notes
For information on related products, visit our website at
http://www.fujifilm.com/products/digital_cameras/index.html Troubleshooting
Appendix
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions: All the safety and not defeat the safety purpose of the This video product should never be An appliance
operating instructions should be polarized plug. placed near or over a radiator or heat and cart com-
read before the appliance is oper- register. bination should
Alternate Warnings: This video
ated. be moved with
product is equipped with a 3-wire Attachments: Do not use attachments
• Retain Instructions: The safety and care. Quick stops,
grounding-type plug, a plug having not recommended by the video
operating instructions should be excessive force,
a third (grounding) pin. This plug will product manufacturer as they may
retained for future reference. and uneven sur-
only fit into a grounding-type power cause hazards.
• Heed Warnings: All warnings on the faces may cause the appliance and
outlet. This is a safety feature. If you
appliance and in the operating in- Water and Moisture: Do not use this cart combination to overturn.
are unable to insert the plug into
structions should be adhered to. video product near water – for ex-
the outlet, contact your electrician Antennas
• Follow Instructions: All operating ample, near a bath tub, wash bowl,
to replace your obsolete outlet. Do Outdoor Antenna Grounding: If an
and use instructions should be fol- kitchen sink, or laundry tub, in a wet
not defeat the safety purpose of the outside antenna or cable system is
lowed. basement, or near a swimming pool,
grounding-type plug. connected to the video product, be
and the like.
Installation Overloading: Do not overload wall sure the antenna or cable system
Power Sources: This video product Power-Cord Protection: Power-Sup- is grounded so as to provide some
outlets and extension cords as this
should be operated only from the ply cords should be routed so that protection against voltage surges
can result in a risk of fire or electric
type of power source indicated on they are not likely to be walked on and built-up static charges. Section
shock.
the marking label. If you are not sure or pinched by items placed upon 810 of the National Electrical Code,
of the type of power supply to your Ventilation: Slots and openings in the or against them, paying particular ANSI/NFPA No. 70, provides informa-
home, consult your appliance dealer cabinet are provided for ventilation attention to cords at plugs, conve- tion with respect to proper grounding
or local power company. For video and to ensure reliable operation of nience receptacles, and the point of the mast and supporting struc-
products intended to operate from the video product and to protect it where they exit from the appliance. ture, grounding of the lead-in wire
battery power, or other sources, refer from overheating, and these open- to an antenna-discharge unit, size of
Accessories: Do not place this video
to the operating instructions. ings must not be blocked or cov- grounding conductors, location of
product on an unstable cart, stand,
ered. antenna-discharge unit, connection
Grounding or Polarization: This video tripod, bracket, or table. The video
The openings should never be to grounding electrodes, and require-
product is equipped with a polar- product may fall, causing serious in-
blocked by placing the video prod- ments for the grounding electrode.
ized alternating-current line plug (a jury to a child or adult, and serious
uct on a bed, sofa, rug, or other simi-
plug having one blade wider than damage to the appliance. Use only
lar surface.
the other). This plug will fit into the with a cart, stand, tripod, bracket, or
This video product should not be
power outlet only one way. This is a table recommended by the manu-
placed in a built-in installation such
safety feature. If you are unable to in- facturer, or sold with the video prod-
as a bookcase or rack unless proper
sert the plug fully into the outlet, try uct. Any mounting of the appliance
ventilation is provided or the man-
reversing the plug. If the plug should should follow the manufacturer’s in-
ufacturer’s instructions have been
still fail to fit, contact your electrician structions, and should use a mount-
adhered to.
to replace your obsolete outlet. Do ing accessory recommended by the
manufacturer.
ii
For Your Safety
Power Lines: An outside antenna sys- Use Service Replacement Parts: When replace-
tem should not be located in the Cleaning: Unplug this video product Servicing: Do not attempt to service ment parts are required, be sure
vicinity of overhead power lines or from the wall outlet before clean- this video product yourself as open- the service technician has used
other electric light or power circuits, ing. Do not use liquid cleaners or ing or removing covers may expose replacement parts specified by the
or where it can fall into such power aerosol cleaners. Use a damp cloth you to dangerous voltage or other manufacturer or have the same
lines or circuits. When installing an for cleaning. hazards. Refer all servicing to quali- characteristics as the original part.
outside antenna system, extreme fied service personnel. Unauthorized substitutions may
care should be taken to keep from Object and Liquid Entry: Never push result in fire, electric shock or other
touching such power lines or circuits objects of any kind into this video Damage Requiring Service: Unplug this hazards.
as contact with them might be fatal. product through openings as they video product from the wall outlet
may touch dangerous voltage and refer servicing to qualified ser- Safety Check: Upon completion of any
EXAMPLE OF ANTENNA GROUNDING points or short out parts that could vice personnel under the following service or repairs to this video prod-
AS PER NATIONAL ELECTRICAL CODE result in a fire or electric shock. Never conditions: uct, ask the service technician to
Ground Clamp Antenna spill liquid of any kind on the video When the power-supply cord or perform safety checks to determine
product. plug is damaged. that the video product is in proper
Lead in Wire
If liquid has been spilled, or objects operating condition.
Electric Lightning: For added protection for
have fallen into the video product.
Service this video product receiver during
If the video product has been ex-
Equipment a lightning storm, or when it is left
posed to rain or water.
Antenna unattended and unused for long pe-
If the video product has been
Ground Discharge Unit riods of time, unplug it from the wall
dropped or the cabinet has been
Clamps (NEC SECTION outlet and disconnect the antenna
damaged.
810-20) or cable system. This will prevent
Power Service If the video product does not op-
Grounding damage to the video product due to
Grounding Electrode erate normally be following the
Conductors lightning and power-line surges.
System (NEC ART 250. operating instructions. Adjust only
PART H) (NEC SECTION
those controls that are covered by
810-21)
the operating instructions as an im-
proper adjustment of other controls
may result in damage and will often
require extensive work by a qualified
technician to restore the video prod-
uct to its normal operation.
When the video product exhibits a
distinct change in performance - this
indicates a need for service.
iii
For Your Safety
iv
For Your Safety
WARNING CAUTION
Do not heat, change or take apart the battery. Do not drop or subject the bat- Do not leave this camera in places subject to extremely high temperatures.
tery to impacts. Do not store the battery with metallic products. Do not use Do not leave the camera in locations such as a sealed vehicle or in
chargers other than the specified model to charge the battery. direct sunlight. This can cause a fire.
Any of these actions can cause the battery to burst or leak and cause Keep out of the reach of small children.
fire or injury as a result. This product could cause injury in the hands of a child.
Use only the battery or AC power adapters specified for use with this camera. Do not place heavy objects on the camera.
Do not use voltages other than the power supply voltage shown. This can cause the heavy object to tip over or fall and cause injury.
The use of other power sources can cause a fire.
Do not move the camera while the AC power adapter is still connected. Do not
If the battery leaks and fluid gets in contact with your eyes, skin or clothing. pull on the connection cord to disconnect the AC power adapter.
Flush the affected area with clean water and seek medical attention or call an This can damage the power cord or cables and cause a fire or electric
emergency number right away. shock.
Do not use the charger to charge batteries other than those specified here. Do not use the AC power adapter when the plug is damaged or the plug socket
The Ni-MH battery charger is designed for FUJIFILM HR-AA Ni-MH connection is loose.
batteries. Using the charger to charge conventional batteries or other This could cause a fire or electric shock.
types of rechargeable batteries can cause the battery to leak fluid,
overheat or burst. Do not cover or wrap the camera or the AC power adapter in a cloth or blanket.
This can cause heat to build up and distort the casing or cause a fire.
Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type. When you are cleaning the camera or you do not plan to use the camera for
an extended period, remove the battery and disconnect and unplug the AC
Do not use in the presence of flammable objects, explosive gases, or dust. power adapter.
Failure to do so can cause a fire or electric shock.
When carrying the battery, install it in a digital camera or keep it in the hard When charging ends, unplug the charger from the power socket.
case. When storing the battery, keep it in the hard case. When discarding, Leaving the charger plugged into the power socket can cause a fire.
cover the battery terminals with insulation tape.
Contact with other metallic objects or battery could cause the bat- Using a flash too close to a person’s eyes may temporarily affect the eyesight.
tery to ignite or burst. Take particular care when photographing infants and young chil-
dren.
Keep Memory Cards out of the reach of small children.
Because Memory Cards are small, they can be swallowed by children. When a memory card is removed, the card could come out of the slot too quick-
Be sure to store Memory Cards out of the reach of small children. If ly. Use your finger to hold it and gently release the card.
a child swallows a Memory Card, seek medical attention or call an Request regular internal testing and cleaning for your camera.
emergency number. Build-up of dust in your camera can cause a fire or electric shock.
• Contact your FUJIFILM dealer to request internal cleaning every 2
years.
CAUTION • Please note this is not a free of charge service.
Do not use this camera in locations affected by oil fumes, steam, humidity or Remove your fingers from the flash window before the flash fires.
dust. Failure to observe this precaution could result in burns.
This can cause a fire or electric shock.
Keep the flash window clean and do not use the flash if the window is obstructed.
Failure to observe these precautions could cause smoke or discoloration.
v
For Your Safety
Power Supply and Battery If you are using a heating pad, take ■ Battery Life • Dispose of used battery promptly.
* Confirm your battery type before read- care not to place the battery di- At normal temperatures, the bat- • Do not drop the battery or other-
ing the following descriptions. rectly against the pad. The camera tery can be used at least 300 times. wise subject it to strong impacts.
may not operate if you use a de- If the time for which the battery • Do not expose the battery to wa-
The following explains proper use of
pleted battery in cold conditions. provides power shortens markedly, ter.
batteries and how to prolong their
this indicates that the battery has • Always keep the battery terminals
life. Incorrect use of batteries can ■ Charging the Battery
clean.
cause shorter battery life, as well as • You can charge the battery using reached the end of its effective life
and should be replaced. • Do not store batteries in hot plac-
leakage, excessive heat, fire or explo- the battery charger (included).
es. Also, if you use the battery for
sion. - The battery can be charged ■ Notes on storage
a long period, the camera body
at ambient temperatures be- • If a battery is stored for long periods
1 Camera uses the Rechargeable and the battery itself will become
tween 0°C and +40°C (+32°F while charged, the performance of
Lithium-ion Battery warm. This is normal. Use the AC
and +104°F). Refer to the Owner’s the battery can be impaired. If the
power adapter if you are taking
* When shipped, the battery is not Manual for the time of charging battery will not be used for some
pictures or viewing images for a
fully charged. Always charge the battery. time, run the battery out before
long period of time.
battery before using it. - You should charge the battery storing it.
* When carrying the battery, install it at an ambient temperature be- • If you do not intend to use the 2 Camera uses AA-size alkaline or Ni-MH
in a digital camera or keep it in the tween +10°C and +35°C (+50°F camera for a long period of time, (nickel-metal hydride) rechargeable
soft case. and +95°F). If you charge the remove the battery from the cam- batteries
battery at a temperature outside era.
■ Battery Features * For details on the batteries that
this range, charging takes longer • Store the battery in a cool place.
• The battery gradually loses its you can use, refer to the Owner’s
because the performance of the - The battery should be stored in
charge even when not used. Use Manual of your camera.
battery is impaired. a dry location with an ambient
a battery that has been charged
- You cannot charge the battery temperature between +15°C and ■ Cautions for Using Battery
recently (in the last day or two) to
at temperatures of 0°C (+32°F) or +25°C (+59°F and +77°F). • Do not heat the batteries or throw
take pictures.
below. - Do not leave the battery in hot or them into a fire.
• To maximize the life of the battery,
• The Rechargeable Lithium-ion Bat- extremely cold places. • Do not carry or store batteries with
turn the camera off as quickly as
tery does not need to be fully dis- metal objects such as necklaces or
possible when it is not being used. ■ Handling the Battery
charged or exhausted flat before Cautions for Your Safety: hairpins.
• The number of available frames will
being charged. • Do not carry or store battery with • Do not expose the batteries to wa-
be lower in cold locations or at low
• The battery may feel warm after it metal objects such as necklaces or ter, and keep batteries from getting
temperatures. Take along a spare
has been charged or immediately hairpins. wet or stored in moist locations.
fully charged battery. You can also
after being used. This is perfectly • Do not heat the battery or throw it• Do not attempt to take apart or
increase the amount of power pro-
normal. into a fire. change the batteries, including
duced by putting the battery in
• Do not recharge a fully charged • Do not attempt to take apart or battery casings.
your pocket or another warm place
battery. change the battery. • Do not subject the batteries to
to heat it and then loading it into
• Do not recharge the battery with strong impacts.
the camera just before you take a
chargers other those specified. • Do not use batteries that are leak-
picture.
ing, deformed, discolored.
vi
For Your Safety
• Do not store batteries in warm or If any liquid at all leaks from CAUTION • Ni-MH batteries have a limited
humid places. the batteries, wipe the battery Do not use the “Discharging re- service life. If a battery can only
• Keep the batteries out of reach of compartment thoroughly and chargeable batteries” function when be used for a short time even after
babies and small children. then load new batteries. alkaline batteries being used. repeated discharge-charge cycles,
• Make sure that the battery polarity • To charge Ni-MH batteries, use the it may have reached the end of its
If any battery fluid comes into
(C and D) is correct. quick battery charger (sold sepa- service life.
contact with your hands or
• Do not use new with used batter- rately). Refer to the instructions
clothing, flush the area thor- ■ Disposing of Batteries
ies. Do not use charged and dis- supplied with the charger to make
oughly with water. Note that • When disposing of batteries, do
charged batteries together. sure that the charger is used cor-
battery fluid can cause loss so in accordance with your local
• Do not use different types or rectly.
of eyesight if it gets into your waste disposal regulations.
brands of batteries at the same • Do not use the battery charger to
eyes. If this occurs, do not rub
time. charge other batteries. 3 Notes on both models ( 1 , 2 )
your eyes. Flush the fluid out
• If you do not intend to use the • Note that the batteries feel warm
with clean water and contact ■ AC Power Adapter
camera for a long period of time, after being charged.
your physician for treatment. Always use the AC Power Adapter
remove the batteries from the • Due to the way the camera is con- with the camera. The use of an AC
camera. Note if the camera is left ■ Using the AA-size Ni-MH batteries structed, a small amount of current Power adapter other than FUJIFILM
with the batteries removed, the correctly is used even when the camera is AC Power Adapter can be damaged
time and date settings are cleared. • Ni-MH batteries left unused in turned off. Note in particular that to your digital camera.
• The batteries feel warm right af- storage for long periods can be- leaving Ni-MH batteries in the For details on the AC power adapter,
ter being used. Before removing come “deactivated”. Also, repeat- camera for a long period will over- refer to the Owner’s Manual of your
the batteries, turn the camera off edly charging Ni-MH batteries discharge the batteries and may camera.
and wait for the batteries to cool that are only partially discharged render them unusable even after • Use the AC power adapter for in-
down. can cause them to suffer from the recharging. door use only.
• Since batteries do not work well in “memory effect”. Ni-MH batteries • Ni-MH batteries will self-discharge • Plug the connection cord plug se-
cold weather or locations, warm that are “deactivated” or affected even when not used, and the time curely into the DC input terminal.
the batteries by placing them in- by “memory” suffer from the prob- for which they can be used may be • Turn off the FUJIFILM Digital cam-
side your garments before use. lem of only providing power for a shortened as a result. era before disconnecting the cord
Batteries do not work well when short time after being charged. To • Ni-MH batteries will deteriorate from the DC input terminal. To dis-
cold. They will work again when prevent this problem, discharge rapidly if over-discharged (e.g. connect, pull out the plug gently.
the temperature returns to normal. and recharge them several times by discharging the batteries in a Do not pull on the cord.
• Soil (such as fingerprints) on the using the camera’s “Discharging flashlight). Use the “Discharging re- • Do not use the AC power adapter
battery terminals makes the bat- rechargeable batteries” function. chargeable batteries” function pro- with any device other than your
teries charge less reducing the Deactivation and memory are spe- vided in the camera to discharge camera.
number of images. Carefully wipe cific to Ni-MH batteries and are not the batteries. • During use, the AC power adapter
the battery terminals with a soft in fact battery faults. will become hot to the touch. This
dry cloth before loading. See Owner’s Manual for the proce- is normal.
dure for “Discharging rechargeable
batteries”.
vii
For Your Safety
• Do not take apart the AC power unless intended only for personal Although the LCD panel is produced ■ Notes on Electrical Interference
adapter. Doing so could be dan- use. Note that some restrictions ap- with highly sophisticated technolo- If the camera is to be used in hos-
gerous. ply to the photographing of stage gies, there may be black spots or pitals or aircrafts, please note that
• Do not use the AC power adapter performances, entertainments and permanently lit spots. This is not a this camera may cause interference
in a hot and humid place. exhibits, even when intended purely malfunction, and does not affect re- to other equipment in the hospital
• Do not subject the AC power for personal use. Users are also asked corded images. or aircraft. For details, please check
adapter to strong shocks. to note that the transfer of Memory with the applicable regulations.
■ Trademark Information
• The AC power adapter may emit a Card containing images or data pro-
• E and xD-Picture Card™ are ■ Explanation of Color Television
humming. This is normal. tected under copyright laws is only System
trademarks of FUJIFILM Corpora-
• If used near a radio, the AC power permissible within the restrictions NTSC: National Television System
tion.
adapter may cause static. If this imposed by those copyright laws. Committee, color television
• IBM PC/AT is a registered trademark
happens, move the camera away
■ Handling Your Digital Camera of International Business Machines telecasting specifications
from the radio. adopted mainly in the U.S.A.,
To ensure that images are recorded Corp. of the U.S.A.
correctly, do not subject the camera • Macintosh, QuickTime, and Mac OS Canada and Japan.
Before Using the Camera
to impact or shock while an image is are trademarks of Apple Inc. in the
Do not aim the camera at extremely PAL: Phase Alternation by Line, a
being recorded. U.S.A. and other countries.
bright light sources, such as the sun color television system ad-
• Windows 7, Windows Vista and the
in a cloudless sky. Failure to observe ■ Liquid Crystal opted mainly by European
Windows logo are trademarks of
this precaution could damage the If the LCD monitor is damaged, take countries and China.
the Microsoft group of companies.
camera image sensor. particular care with the liquid crystal
in the monitor. If any of the follow-
• IrSimple™ Trademark is owned by ■ Exif Print (Exif ver. 2.3)
■ Test Shots Prior to Photography the Infrared Data Association®. Exif Print Format is a newly revised
ing situations arise, take the urgent
For important photographs (such as • IrSS™ Trademark or IrSimpleShot™ digital camera file format that con-
action indicated.
weddings and overseas trips), always Trademark is owned by the Infra- tains a variety of shooting informa-
• If liquid crystal comes in contact
take a test shot and view the im- red Data Association®. tion for optimal printing.
with your skin:
age to make sure that the camera is • The SDHC and SDXC logos are
Wipe the area with a cloth and
working normally. trademarks of SD-3C, LLC. IMPORTANT NOTICE: Read Before
then wash thoroughly with soap
• FUJIFILM Corporation cannot ac- • HDMI logo is a trademark. Using the Software
and running water.
cept liability for any incidental • YouTube is a trademark of Google Direct or indirect export, in whole or
• If liquid crystal gets into your eye:
losses (such as the costs of photog- Inc. in part, of licensed software without
Flush the affected eye with clean
raphy or the loss of income from • Other company or product names the permission of the applicable
water for at least 15 minutes and
photography) incurred as a result are trademarks or registered trade- governing bodies is prohibited.
then seek medical assistance.
of faults with this product. marks of the respective compa-
• If liquid crystal is swallowed:
■ Notes on Copyright nies.
Flush your mouth thoroughly with
Images recorded using your digital water. Drink large quantities of wa-
camera system cannot be used in ter and induce vomiting. Then seek
ways that infringe copyright laws medical assistance.
without the consent of the owner,
viii
About This Manual
Before using the camera, read this manual and the warnings on pages ii–viii. For information on spe-
cific topics, consult the sources below.
✔ Camera Q & A ......................................................
......................................................pg.
pg. x ✔ Table of Contents .............................................pg.
............................................. pg. xiii
Know what you want to do but don’t know the The “Table of Contents” gives an overview of the
name for it? Find the answer in “Camera Q & A.” entire manual. The principal camera operations
are listed here.
✔ Troubleshooting ............................................. pg. 112 ✔ Warning Messages and Displays ...................... pg. 119
Having a specific problem with the camera? Find Find out what’s behind that flashing icon or error
the answer here. message in the display.
✔ Glossary .........................................................
.........................................................pg.
pg. 123
The meanings of some technical terms may be
found here.
Memory Cards
Pictures can be stored in an optional SD, SDHC, and SDXC memory cards (pg. 13), referred to in this manual as
“memory cards”.
ix
Camera Q & A
Find items by task.
Camera Setup
Question Key phrase See page
How do I set the camera clock? Date and time 15
Can I set the clock to local time when I travel? Time difference 104
How do I keep the display from turning off automatically? Auto power off 107
How do I make the display brighter or darker? LCD brightness 107
Operation and shutter volume 102
How do I stop the camera beeping and clicking?
Silent mode 19
Can I change the sound the shutter makes? Shutter sound 102
What do the icons in the display mean? Displays 4
How much charge is left in the battery? Battery level 17
Can I add shooting date and time to the pictures? Date stamp 108
Sharing Pictures
Question Key phrase See page
Can I print pictures on my home printer? Printing pictures 63
x
Camera Q & A
Taking Pictures
Question Key phrase See page
How can I avoid blurred pictures? Dual IS mode 18
How can I make good portraits? Intelligent Face Detection 32
Can the camera automatically adjust settings for different scenes? M mode 16
Can I choose my own settings for different scenes? Scene position 22
How can I be sure my subject is smiling when I take a photograph? Smile detection 23
How can I be sure that nobody blinked when the photo was taken? Blink detection 33
Can I prioritize to focus the specified person’s face? Face Recognition 84
How do I shoot close-ups? Macro mode (close-ups) 36
How do I keep the flash from firing?
How do I stop my subjects’ eyes glowing red when I use the flash? Flash mode 37
How do I “fill-in” shadows on back-lit subjects?
How do I take a series of pictures in a single burst? Continuous Shooting mode 41
How do I take a group portrait that includes the photographer? Self-timer mode 39
How do I shoot a panorama? Motion panorama 25
Can I choose shutter speed and aperture? P, S, A, and M modes 27
Can I save and recall camera settings? C mode 31
How do I adjust exposure? Exposure compensation 45
How do I keep a moving subject in focus? Tracking 84
How do I shoot movies? Recording movies 58
How do I frame pictures in the viewfinder? EVF/LCD button 5
xi
Camera Q & A
Viewing Pictures
Question Key phrase See page
How do I view my pictures? Single-frame playback 47
How can I delete pictures easily? The b button 21
How can I select and delete individual pictures or delete all pictures
Deleting pictures 55
at once?
Can I zoom in on pictures during playback? Playback zoom 48
Can I mark images with favorite (I) rating? I Favorites 48
How do I view a lot of pictures at once? Multi-frame playback 50
Can I create photobooks from my favorite pictures? Photobook assist 52
How do I find pictures? Image search 54
Can I protect my pictures from accidental deletion? Protect 95
Can I hide the icons in the display when viewing my pictures? Choosing a display format 47
Can I select pictures for upload to YouTubeTM?
Uploading pictures 92
Can I select pictures for upload to Facebook?
xii
Table of Contents
For Your Safety ................................................................................. ii Basic Photography and Playback
IMPORTANT SAFETY INSTRUCTIONS ...................................... ii Taking Pictures in M (Scene Recognition) Mode ...16
Safety Notes .................................................................................... iv Viewing Pictures ............................................................................21
About This Manual ......................................................................... ix
Camera Q & A ..................................................................................... x More on Photography
Shooting Mode ...............................................................................22
Before You Begin M SCENE RECOGNITION..................................................22
Introduction ....................................................................................... 1 B AUTO ..........................................................................................22
Symbols and Conventions .......................................................... 1 SP SCENE POSITION ....................................................................22
Supplied Accessories .................................................................... 1 N MOTION PANORAMA .....................................................25
Parts of the Camera ....................................................................... 2 P: PROGRAM AE ............................................................................27
Camera Displays .......................................................................... 4 S: SHUTTER PRIORITY AE ...........................................................28
The Mode Dial .............................................................................. 6 A: APERTURE PRIORITY AE ........................................................29
M: MANUAL ....................................................................................30
First Steps
C: CUSTOM MODE ........................................................................31
The Strap and Lens Cap ................................................................ 7 Intelligent Face Detection .........................................................32
Charging the Battery ..................................................................... 8 Blink Detection .............................................................................33
Inserting the Battery and a Memory Card .........................10 Focus Lock.........................................................................................34
Turning the Camera On and Off..............................................14 F Macro and Super Macro Modes (Close-ups) ................36
Shooting Mode .............................................................................14 N Using the Flash (Intelligent Flash) .....................................37
Playback Mode ..............................................................................14 J Using the Self-Timer ...............................................................39
Basic Setup .......................................................................................15 I Continuous Shooting (Burst Mode) ................................41
c Instant Zoom ............................................................................43
d Exposure Compensation .....................................................45
xiii
Table of Contents
Connections
Viewing Pictures on TV ...............................................................61
Printing Pictures via USB............................................................63
Connecting the Camera ............................................................63
Printing Selected Pictures ........................................................63
Printing the DPOF Print Order.................................................64
Creating a DPOF Print Order ....................................................66
Viewing Pictures on a Computer ............................................69
Installing the Software...............................................................69
Connecting the Camera ............................................................73
xiv
Table of Contents
xv
Memo
xvi
Introduction
Symbols and Conventions
The following symbols are used in this manual:
Supplied Accessories
The following items are included with the camera:
NP-85 rechargeable battery BC-85 battery charger Plug adapter * USB-A/V cable
• Basic Manual
1
Introduction
2
Introduction
3
Introduction
Camera Displays
The following indicators may appear during shooting and playback. The indicators displayed vary with
camera settings.
■ Shooting
1 Number of available frames ........... 124 13 Focus frame .................................................34
19 2 Image size .....................................................77 14 Blur warning .............................37, 115, 119
DATE 100 3 Focus warning ...........................................19 15 Date and time.............................................15
N 4 Date stamp................................................108 16 Shutter speed and aperture .............27
5 Silent mode .................................................19 17 Sensitivity ......................................................76
6 Burst mode ..................................................41 18 Image quality ..............................................81
12/31/2050 10 : 00 AM 7 Metering ........................................................83 19 FinePix color ................................................78
SET 8 Intelligent Face Detection 20 White balance ............................................81
250 F3. 1
indicator .........................................................32 21 Battery level .................................................17
9 Shooting mode .........................................22 22 Dual IS mode ..............................................18
10 Flash mode...................................................37 23 Exposure indicator ..................................45
11 Macro (close-ups) mode .....................36 24 Exposure compensation
12 Self-timer indicator .................................39 indicator .........................................................45
■ Playback
1 Gift image .....................................................47 7 DPOF print indicator ..............................66
100-0001 2 Silent mode .................................................19 8 Voice memo indicator...........................99
100 3 Red-eye removal indicator.................94 9 Photobook assist indicator ................52
4:3 N 4 Intelligent Face Detection 10 Mark for upload to...................................92
indicator .........................................................32 11 Frame number ........................................106
5 Playback mode indicator .............21, 47 12 Rating...............................................................48
6 Protected image .......................................95
12/31/2050 10 : 00 AM
1/250 F3.1
4
Introduction
EVF
LCD
5
Introduction
6
The Strap and Lens Cap
Attaching the Strap The Lens Cap
Attach the strap to the two strap eyelets as shown Attach the lens cap as shown.
below.
First Steps
To avoid losing the lens cap, pass the supplied
string through the eyelet (q) and secure the lens
cap to the strap (w).
3 Caution
To avoid dropping the camera, be sure the strap is cor-
rectly secured.
7
Charging the Battery
The battery is not charged at shipment. Charge the battery before use.
Arrow
CFD label
Charge lamp
The camera uses an NP-85 rechargeable battery.
8
Charging the Battery
First Steps
Off Battery not inserted. Insert the battery.
On (green) Battery fully charged. Remove the battery.
On (orange) Battery charging. —
Blinks (orange) Battery fault. Unplug the charger and remove the battery.
9
Inserting the Battery and a Memory Card
After charging the battery, insert the battery and memory card as described below.
3 Caution
Insert the battery in the correct orientation. Do
NOT use force or attempt to insert the battery up-
side down or backwards. The battery will slide in
easily in the correct orientation.
10
Inserting the Battery and a Memory Card
First Steps
the back of the slot.
3 Cautions
• Be sure card is in the correct orientation; do not
insert at an angle or use force.
• SD/SDHC/SDXC memory
cards can be locked, mak-
ing it impossible to format
the card or to record or Write-protect
delete images. Before in- switch
serting an SD/SDHC/SDXC
memory card, slide the write-protect switch to
the unlocked position.
11
Inserting the Battery and a Memory Card
12
Inserting the Battery and a Memory Card
First Steps
3 Cautions
• Do not turn the camera off or remove the memory card while the memory card is being formatted or data are being recorded to or
deleted from the card. Failure to observe this precaution could damage the card.
• Format SD/SDHC/SDXC memory cards before first use, and be sure to reformat all memory cards after using
them in a computer or other device. For more information on formatting memory cards, see page 105.
• Memory cards are small and can be swallowed; keep out of reach of children. If a child swallows a memory card,
seek medical assistance immediately.
• miniSD or microSD adapters that are larger or smaller than the standard dimensions of an SD/SDHC/SDXC card
may not eject normally; if the card does not eject, take the camera to an authorized service representative. Do
not forcibly remove the card.
• Do not affix labels to memory cards. Peeling labels can cause camera malfunction.
• Movie recording may be interrupted with some types of SD/SDHC/SDXC memory card. Use a y card or
better when shooting HD movies.
• Formatting a memory card in the camera creates a folder in which pictures are stored. Do not rename or delete
this folder or use a computer or other device to edit, delete, or rename image files. Always use the camera to
delete pictures from memory cards; before editing or renaming files, copy them to a computer and edit or re-
name the copies, not the originals.
13
Turning the Camera On and Off
Shooting Mode Playback Mode
Slide the G switch in the direction shown To turn the camera on and begin playback, press
below. The lens will extend automatically. the a button for about a second.
ENGLISH
FRANCAIS
First Steps
DEUTSCH
ESPAÑOL
PORTUGUÊS
SET NO
1.2 Press MENU/OK.
2014
2013
hour, or minute and press up or down to change. To change
YY. MM. DD 2012 1. 1 12 : 00 the order in which the year, month, and day are displayed, high-
2011 AM
2010
light the date format and press the selector up or down.
SET NO
15
Taking Pictures in M (Scene Recognition) Mode
This section describes how to take pictures in M mode.
subject.
• c (LANDSCAPE): Man-made or natural landscape.
• d (NIGHT): Poorly-lit landscape.
• e (MACRO): Subject close to camera.
2 Rotate
Select M mode.
the mode dial to M.
• f (NIGHT PORTRAIT): Poorly-lit portrait subject.
• g (BACKLIT PORTRAIT): Back-lit portrait subject.
a (AUTO) is selected if none of the above are detected.
16
Taking Pictures in M (Scene Recognition) Mode
1 Note
When using the zoom control and side lever simulta-
neously, the zoom control is activated.
17
Taking Pictures in M (Scene Recognition) Mode
18
Taking Pictures in M (Scene Recognition) Mode
Silent Mode
In situations in which camera sounds or lights may
5 Press
Focus.
the shutter button halfway
be unwelcome, hold the DISP/BACK button down until to focus.
o is displayed (note that silent mode is not available
during movie or voice memo playback).
1 Note
The lens may make a noise when the camera fo-
cuses; this is normal. In M mode, the cam-
19
Taking Pictures in M (Scene Recognition) Mode
6 Smoothly
Shoot.
press the shutter button
The Indicator Lamp
2 Tip: The Shutter Button The indicator lamp shows camera status as follows:
The shutter button has two positions. Pressing the
Indicator lamp Camera status
shutter button halfway (q) sets focus and exposure;
Glows green Focus locked.
to shoot, press the shutter button the rest of the way
Blur, focus, or exposure warning. Pic-
down (w). Blinks green
ture can be taken.
Double Blinks green Recording pictures. Additional pic-
beep Click and orange tures can be taken.
q w Glows Recording pictures. No additional pic-
orange tures can be taken at this time.
Flash charging; flash will not fire when
Blinks orange
picture is taken.
Press halfway Press the rest of
Lens or memory error (memory card
the way down
Blinks red full or not formatted, format error, or
1 Note other memory error).
If the subject is poorly lit, the AF-assist illuminator may 2 Tip: Warnings
light to assist focus (pg. 35). For information on using Detailed warnings appear in the display. See pages
the flash when lighting is poor, see page 37. 119–122 for more information.
20
Viewing Pictures
Pictures can be viewed in the monitor. When taking important photographs, take a test shot and
check the results.
OK. FRAME
SELECTED FRAMES
The most recent picture will be displayed in ALL FRAMES
100-0001
• To delete the picture, press ERASE OK?
MENU/OK.
YES CANCEL
21
Shooting Mode
Choose a shooting mode according to the scene or type of subject. To choose a shooting mode, rotate
the mode dial to the desired setting (pg. 6). The following modes are available:
22
Shooting Mode
Scene Description
The camera takes three shots: one at the current zoom ratio, a second zoomed in 1.4 ×, and a third
B ZOOM BRACKETING
zoomed in 2 ×.
Get good results with backlit subjects and other difficult lighting. The camera takes two shots: one
C NATURAL & N
without the flash and one with.
D NATURAL LIGHT Capture natural light indoors, under low light, or where the flash can not be used.
C PORTRAIT Choose this mode for soft-toned portraits with natural skin tones.
D BABY MODE Choose for natural skin tones when taking portraits of infants. The flash turns off automatically.
K SMILE&SHOOT The shutter is released automatically when Intelligent Face Detection detects a smiling face.
M LANDSCAPE Choose this mode for crisp, clear daylight shots of buildings and landscapes.
N SPORT Choose this mode when photographing moving subjects. Priority is given to faster shutter speeds.
More on Photography
Choose this mode for poorly lit twilight or night scenes. Sensitivity is automatically raised to reduce
O NIGHT
blur caused by camera shake.
H NIGHT (TRIPOD) Choose this mode for slow shutter speeds when shooting at night. Use a tripod to prevent blur.
Slow shutter speeds are used to capture the expanding burst of light from a firework. Press the d
P FIREWORKS button to display a shutter-speed selection dialog and press the selector up and down to choose a
shutter speed.
Q SUNSET Choose this mode to record the vivid colors in sunrises and sunsets.
R SNOW Choose for crisp, clear shots that capture the brightness of scenes dominated by shining white snow.
S BEACH Choose for crisp, clear shots that capture the brightness of sunlit beaches.
U PARTY Capture indoor background lighting under low-light conditions.
V FLOWER Choose for vivid close-ups of flowers. The camera focuses in the macro range.
W TEXT Take clear pictures of text or drawings in print. The camera focuses in the macro range.
23
Shooting Mode
D Natural Light
Capture natural light indoors, under low light, or
where the flash can not be used. The flash turns
Wide Tall off and sensitivity is raised to reduce blur.
1 Notes
• Digital zoom can not be used. If digital zoom is active
when B mode is selected, zoom will be set to the
maximum optical zoom position.
• Burst shooting options are limited to I and OFF.
24
Shooting Mode
N MOTION PANORAMA
In this mode, you can take up to three pictures and join them together to form a panorama. Use of a
tripod is recommended to assist in composing overlapping shots.
1 N.
Rotate the mode dial to 6 ous
Frame the next shot to overlap with the previ-
picture by superimposing y on + so that
they form a solid circle (z). The camera will
2 Press MENU/OK to display the shooting menu. release the shutter automatically.
Pan direction
3 Select C AUTO from SHOOTING MENU 2 /2
More on Photography
MODE 1 2 3 1 2 3
P MODE in the shoot- MANUAL
AUTO
ing menu (pg. 79).
SET
rection and press MENU/OK. 7 Take the last shot as described in Step 6.
5 posure
Take a photograph. Ex-
and white balance
1 Note
To end shooting and create a panorama after the
for the panorama are set first or second shot, press the multi selector up after
with the first shot. completing Step 5 or Step 6 and proceed to Step 8.
1 Note
The camera zooms all the way out and zoom re-
8 Press MENU/OK to save the picture.
mains fixed at the widest angle until shooting is
complete.
25
Shooting Mode
26
Shooting Mode
P: PROGRAM AE
In this mode, the camera sets exposure automati- Program Shift
cally. If desired, you can choose different combi- Press the d button to choose the desired combina-
nations of shutter speed and aperture that will tion of shutter speed and aperture. Values that differ
produce the same exposure (program shift). from those automatically selected by the camera are
shown in yellow. The default values can be restored
by raising the flash or turning the camera off. Pro-
gram shift is not available when the flash is raised.
Shutter speed
More on Photography
SET
250 F3. 1 Aperture
3 Caution
If the subject is outside the meter- P
sure again.
27
Shooting Mode
S: SHUTTER PRIORITY AE
In this mode, you choose the shutter speed while the camera adjusts aperture for optimal exposure.
5 be
Take pictures. If the correct exposure can not
2 Press the d button. Shutter speed
and aperture will be displayed.
achieved at the selected shutter speed, ap-
erture will be displayed in red when the shut-
S
ter button is pressed halfway. Adjust shut-
ter speed until the correct exposure can be
achieved.
Shutter speed
SET 3 Caution
250 F3.1
If the subject is outside the metering range of the cam-
era, the aperture display will show “---”. Press the shut-
3 choose
Press the selector up or down to
the shutter speed.
ter button halfway to measure exposure again.
28
Shooting Mode
A: APERTURE PRIORITY AE
In this mode, you choose the aperture while the camera adjusts shutter speed for optimal exposure.
5 be
Take pictures. If the correct exposure can not
2 Press the d button. Shutter speed
and aperture will be displayed.
achieved at the selected aperture, shutter
speed will be displayed in red when the shut-
A
ter button is pressed halfway. Adjust aperture
More on Photography
until the correct exposure can be achieved.
Aperture 3 Caution
SET If the subject is outside the metering range of the cam-
250 F3. 1
era, the shutter speed display will show “---”. Press the
shutter button halfway to measure exposure again.
3 choose
Press the selector up or down to
the aperture.
29
Shooting Mode
M: MANUAL
In this mode, you choose both shutter speed and aperture. If desired, exposure can be altered from
the value suggested by the camera.
6 Take pictures.
2 Press the d button. Shutter speed
and aperture will be displayed. The Exposure Indicator
M
The amount the picture will be under- or over-ex-
posed at current settings is shown by the exposure
indicator. Pictures taken with the indicator to the left
Shutter speed of center (“–“) will be underexposed, pictures taken
SET
250 F3. 1 Aperture with the indicator is to the right of center (“+”), over-
exposed.
3 choose
Press the selector up or down to
the shutter speed.
M
SET
4 choose
Press the selector left or right to
the aperture.
250 F3. 1
Underexposed Overexposed
Exposure indicator
30
Shooting Mode
C: CUSTOM MODE
In P, S, A, and M modes, the K CUSTOM SET option in the shooting
menu (pg. 79) can be used to save current camera and menu settings.
These settings are recalled whenever the mode dial is rotated to C (cus-
tom mode).
More on Photography
Setup menu A IMAGE DISP, L DUAL IS MODE, C AF ILLUMINATOR, D DIGITAL ZOOM, E EVF/LCD MODE
Shooting mode (P, S, A, or M), continuous shooting mode, instant zoom, macro mode, exposure compensa-
Other
tion, flash mode, shutter speed, aperture, display type (EVF/LCD), indicators/best framing
31
Intelligent Face Detection
Intelligent Face Detection allows the camera to automatically detect human faces and set focus and
exposure for a face anywhere in the frame for shots that emphasize portrait subjects. Choose for
group portraits (in horizontal or vertical orientations) to prevent the camera from focusing on the back-
ground.
32
Intelligent Face Detection
More on Photography
(pg. 105), printing (pg. 63), and cropping (pg. 96).
FACE ZOOM NEXT
STORE ERASE STORE ERASE
3 Caution
Blink detection is not performed if the camera fails to
detect a face or when OFF is selected for A IMAGE
DISP..
2 Tip: Blink Detection
Blink detection can be turned on or off in the setup
menu (pg. 103).
33
Focus Lock
To compose photographs with off-center subjects:
2 Press
Focus.
the shutter button halfway to set fo-
cus and exposure. Focus and exposure will
remain locked while the shutter button is
4 Press
Shoot.
the shutter-release button the rest of
pressed halfway (AF/AE lock). the way down to take the picture.
34
Focus Lock
More on Photography
the distance to the subject.
35
F Macro and Super Macro Modes (Close-ups)
For close-ups, press the selector left (F) to choose from the macro options shown below.
Choose from F (macro mode),
G (super macro mode), or
OFF (macro mode off)
When macro mode is in effect, the camera focuses on subjects near the center of the frame. Use the
zoom control to compose pictures. In super macro mode, optical zoom can not be adjusted and the
flash can not be used.
1 Notes
• Use of a tripod is recommended to prevent blur caused by camera shake.
• Flash compensation may be required when using the flash (pg. 87).
• Using the flash at close range may cast a lens shadow. Zoom a little or have more distance from the subject.
36
N Using the Flash (Intelligent Flash)
When the flash is used, the camera’s Intelligent Flash system instantly analyzes the scene based on
such factors as the brightness of the subject, its position in the frame, and its distance from the camera.
Flash output and sensitivity are adjusted to ensure that the main subject is correctly exposed while
preserving the effects of ambient background lighting, even in dimly-lit indoor scenes. Use the flash
when lighting is poor, for example when shooting at night or indoors under low light.
More on Photography
under dim light. At slow shutter speeds, k will be displayed to warn that pictures
may be blurred; use of a tripod is recommended.
Mode Description
A/K
The flash fires when required. Recommended in most situations.
(AUTO FLASH)
N/L The flash fires whenever a picture is taken. Use for backlit subjects or for natural
(FORCED FLASH) coloration when shooting in bright light.
O/M Capture both the main subject and the background under low light (note that
(SLOW SYNCHRO) brightly lit scenes may be overexposed).
37
N Using the Flash (Intelligent Flash)
3 Press
Focus.
the shutter button halfway to focus. If the flash will fire, p will be displayed when
the shutter button is pressed halfway. At slow shutter speeds, k will appear in the
display to warn that pictures may be blurred; use of a tripod is recommended.
4 Press
Shoot.
the shutter button the rest of the way down to shoot.
3 Caution
The flash may fire several times with each shot. Do not move the camera until shooting is com-
plete.
1 Note
The peripheral part of an image may be dark when using the flash.
Red-Eye Removal
When Intelligent Face Detection is active (pg. 32), and ON is selected for B RED EYE REMOVAL in
the setup menu (pg. 94), red-eye removal is available in K, L, and M.
Red-eye removal minimizes “red-eye” caused when light from the flash is reflected from the subject’s
retinas as shown in the illustration at right.
38
J Using the Self-Timer
The camera offers a ten-second timer that allows photographers to appear in their own photographs,
and a two-second timer that can be used to avoid blur caused by the camera moving when the shutter
button is pressed.
More on Photography
2 Press
Focus.
the shutter button halfway to focus.
3 Caution
Stand behind the camera when using the shutter button. Standing in front of the lens can inter-
fere with focus and exposure.
39
J Using the Self-Timer
40
I Continuous Shooting (Burst Mode)
Capture motion in a series of pictures.
More on Photography
OFF
N The camera takes pictures while the shutter button is pressed. Shooting TOP6
(N LONG PERIOD) ends when the shutter button is released or memory is full.
K
The camera takes up to 20 pictures while the shutter button is pressed.
(K TOP 20)
J
The camera takes up to 40 pictures while the shutter button is pressed.
(J TOP 40)
Each time the shutter-release button is pressed, the camera takes three
shots: one using the metered value for exposure, the second overex-
posed by the amount selected for J AE BKT EV STEPS in the shoot-
O
ing menu (pg. 87), and the third underexposed by the same amount (the
(AE BKT)
camera may not be able to use the selected bracketing increment if the
amount of over- or under-exposure exceeds the limits of the exposure
metering system).
41
I Continuous Shooting (Burst Mode)
2 Press
Focus.
the shutter button halfway to focus.
3 Pictures
Shoot.
will be taken while the shutter button is pressed. Shooting ends when the
shutter button is released, memory is full, or the selected number of shots has been
taken.
1 Notes
• Focus and exposure are determined by the first frame in each series. The flash turns off automatically; the previ-
ously-selected flash mode is restored when continuous shooting is turned off.
• Frame rate varies with shutter speed.
• If the self-timer is used when L and N are selected, only one picture will be taken when the shutter button is
pressed.
• At a setting of J, white lines may appear in bright areas of the image; these can be avoided by choosing K
mode.
• The number of pictures that can be recorded depends on the memory available. AE bracketing is only available
if there is sufficient memory for three pictures. Additional time may be required to record pictures when shoot-
ing ends.
42
c Instant Zoom
In instant zoom, the area surrounding the frame is visible in the display. Use to frame erratically moving
subjects such as children, pets, and athletes at sporting events.
More on Photography
full-sized picture.
2 Choose a frame.
Press the c button to 2 Tip: Intelligent Face Detection
cycle through framing Intelligent Face Detection will not detect faces outside
options as shown be- the selected frame.
low. 3 Caution
Only horizontal (landscape-orientation) framing is
Horizontal, Horizontal,
available when I, L, N, or O is selected for con-
low zoom high zoom
tinuous shooting mode.
No zoom
Vertical, Vertical,
high zoom low zoom
43
c Instant Zoom
■ Digital Zoom
1 Enable digital zoom.
Select ON for the D DIGITAL ZOOM op-
4 Frame the picture.
Use the zoom control to choose the area that
tion in the setup menu (pg. 107). will be included in the final photograph.
2 Choose a subject.
Frame the subject in the center of the display
using digital zoom.
44
d Exposure Compensation
Use exposure compensation when photographing very bright, very dark, or high-contrast subjects.
Exposure indicator
4 Take pictures.
SET
250 F3.1 1 Note
A d icon and exposure indicator are displayed at set-
2 Choose a value. tings other than ±0. Exposure compensation is not
More on Photography
Press the selector left or right. The reset when the camera is turned off; to restore normal
effect is visible in the display. exposure control, choose a value of ±0.
45
d Exposure Compensation
46
Playback Options
To view the most recent picture in the monitor, Choosing a Display Format
press the a button. Press the DISP/BACK button to cycle through playback
display formats as shown below.
100-0001
More on Playback
on 100-0001 off
3 Favorites
12/31/2050 10 : 00 AM (pg. 48)
1 Note
Pictures taken using other cameras are indicated by a m (“gift image”) icon during playback.
47
Playback Options
48
Playback Options
More on Playback
aperture, r FinePix color, t Flash mode, y White bal-
ance, u Exposure compensation, i Frame number,
o Picture (overexposed areas blink on and off), !0 Histo-
gram
49
Playback Options
Multi-Frame Playback
To change the number of images dis- Use the selector to highlight images and press
played during playback, select W. MENU/OK to view the highlighted image full frame.
In the nine- and hundred-frame displays, press
the selector up or down to view more pictures.
2 Tip: Two-Frame Display
Two-frame display can be used
12/31/2050 10 : 00 AM to compare pictures taken in
C mode.
50
Viewing Panoramas
To view a panorama, display in single-frame view and press the selector down.
PLAY
STOP PAUSE
More on Playback
End playback Press the selector up to end playback.
51
k PhotoBook Assist
Create books from your favorite photos.
Creating a PhotoBook
Select k PHOTOBOOK ASSIST in the play- 5 Scroll through the images and press the selec-
1 back menu. tor up to select or deselect the current image
for inclusion in the book. To display the current
2 Highlight NEW BOOK. image on the cover, press the selector down.
1 Note
The first picture selected automatically becomes
3 book
Press MENU/OK to display the new
dialog.
the cover image. Press the selector down to select
a different picture for the cover.
4 Choose pictures for the new book.
• SELECT FROM ALL: Choose from all the 6 Press MENU/OK to exit when the book
is complete.
pictures available.
• SELECT BY IMAGE SEARCH: Choose from pictures
matching selected search conditions (pg. 54).
7 Highlight COMPLETE PHOTOBOOK.
SELECT IMAGES FOR PHOTOBOOK
1 Note
Choose SELECT ALL to select all photos, or all pho-
tos matching the specified search conditions, for
the book.
52
k PhotoBook Assist
8 added
Press MENU/OK. The new book will be
to the list in the photobook
Viewing PhotoBooks
Highlight a book in the photobook assist menu
assist menu. and press MENU/OK to display the book, then press
3 Cautions the selector left and right to scroll through the
• Photobooks can contain up to 300 pictures. pictures. Press DISP/BACK to return to the photo-
• Books that contain no photos are automatically book assist menu.
deleted.
PhotoBooks Editing and Deleting PhotoBooks
Photobooks can be copied to a computer using the
supplied MyFinePix Studio software.
1 Display the photobook and press
MENU/OK to view book edit options.
More on Playback
• EDIT: Edit the book as described in “Creating a
PhotoBook” on page 52.
• ERASE: Delete the current photobook.
53
b Image Search
Search for pictures by date, subject, scene, file type, and rating.
1 menu.
Select b IMAGE SEARCH in the playback 3 Select a search condition. Only pictures that
match the search condition will be displayed.
To delete or protect selected pictures or to
2 Highlight one of the following options and
press MENU/OK:
view the selected pictures in a slide show,
press MENU/OK and choose from the following
Option Description
options:
Find all pictures taken on a selected
BY DATE Option See page
date.
Find all pictures based on specified face A ERASE 55
BY FACE D PROTECT 95
information.
Find all pictures with a specified rating I SLIDE SHOW 90
BY I FAVORITES
(pg. 48).
BY SCENE
Find all pictures that match a selected
scene.
4 To end the search, select EXIT SEARCH.
BY TYPE OF DATA Find all still pictures or all movies.
Find all pictures selected for upload to a
BY UPLOAD MARK
specified destination (pg. 92).
54
A Deleting Pictures
In the playback menu, you can select and delete Deleting One Picture
individual pictures or delete all pictures at once. Press g or h to select the desired picture and
Note that deleted pictures cannot be recovered. then press the MENU/OK button to delete the pic-
Copy important pictures to a computer or other ture that is displayed.
storage device before proceeding.
Press the MENU/OK button to display the playback 2 Tips
menu, and then select the desired method for de- • The picture is deleted when the MENU/OK button is
pressed, so be careful not to accidentally delete pictures.
leting pictures on the A ERASE screen.
• Pressing the MENU/OK button repeatedly will delete
PLAYBACK MENU 1 /2 Delete one picture consecutive pictures. Press g or h to select the
PHOTOBOOK BACK
ASSIST
FRAME
IMAGE SEARCH Delete multiple picture that you want to delete before you press the
ERASE SELECTED FRAMES
MARK FOR
ALLUPLOAD
FRAMES pictures MENU/OK button.
SLIDE SHOW
RED EYE REMOVAL
Delete all pictures
More on Playback
55
A Deleting Pictures
1 lete
Select each picture you want to de-
and press the MENU/OK button.
56
A Deleting Pictures
More on Playback
57
F Recording Movies
Shoot short movies at 30 frames per second. Sound is recorded via the built-in microphone; do not
cover the microphone during recording.
1 mode).
Rotate the mode dial to F (movie 4 movie
Press DISP/BACK. The camera returns to the
recording screen.
Zooming While Recording a Movie
12s Time available The zoom can be used while recording a movie.
STANDBY
is displayed in In the setup menu, select 1 DIGITAL or 2 OPTICAL
monitor (pg. 103).
1 DIGITAL: Image quality may deteriorate when
2 from
Press the F button and select a frame size
the O QUALITY menu. Select h 1280
the zoom is used.
2 OPTICAL: The sound of the camera zooming
(1280 × 720) for an aspect ratio of 16 : 9 (High may be heard when playing movie.
Definition), f (640 × 480) to record standard Avoiding Blurred Pictures
definition movies, or g (320 × 240) for lon- If the subject is poorly lit, blurring caused by camera
Movies
ger movies. Press DISP/BACK to exit to movie shake can be reduced using the L DUAL IS MODE
mode. option in the setup menu (pg. 103).
58
F Recording Movies
Movies
a malfunction.
59
a Viewing Movies
During playback (pg. 47), 100-006
Progress is shown in the monitor during play-
movies are displayed in the back.
monitor as shown at right. 15s
Operation Description
2 Tip: Viewing Movies on a Computer
Start/pause
Press the selector down to start playback. Copy movies to the computer before viewing.
playback Press again to pause.
End Press the selector up to end playback. If 3 Caution
playback/playback is not in progress, pressing the Do not cover the speaker during playback.
delete selector up will delete the current movie.
Press the selector right to advance, left to
Advance/ rewind. If playback is paused, the movie
rewind will advance or rewind one frame each
time the selector is pressed.
Press MENU/OK to pause playback and dis-
Adjust play volume controls. Press the selector
volume up or down to adjust the volume; press
MENU/OK again to set the volume.
60
Viewing Pictures on TV
Connect the camera to a TV to show pictures to a group.
HDMI
An HDMI cable (available from third-party suppliers; pg. 127) can be used to connect the camera to High
Definition (HD) devices (playback only). The USB cable can not be used while an HDMI cable is connected.
Connections
connector connector
61
Viewing Pictures on TV
3 Tune the television to the video or HDMI input channel. See the documentation supplied with the
television for details.
4 pictures
Press the a button for about a second to turn the camera on. The camera monitor turns off and
and movies are played back on the TV. Note that the camera volume controls have no ef-
fect on sounds played on the TV; use the television volume controls to adjust the volume.
1 Note
Image quality drops during movie playback.
3 Caution
When connecting the cable, be sure the connectors are fully inserted.
62
Printing Pictures via USB
If the printer supports PictBridge, the camera can be connected directly to the printer and
pictures can be printed without first being copied to a computer. Note that depending on
the printer, not all the functions described below may be supported.
Connecting the Camera Printing Selected Pictures
Connect the supplied USB-A/V cable as shown 1 Press the selector left or right to dis-
1 and turn the printer on. play a picture you wish to print.
2 choose
Press the selector up or down to
the number of copies (up to
99).
Connections
USB PICTBRIDGE
TOTAL: 00000
YES CANCEL
00 SHEETS
FRAME
OK SET
4 Press MENU/OK to start printing.
63
Printing Pictures via USB
2 Tip: Printing the Date of Recording Printing the DPOF Print Order
To print the date of recording on pictures, press DISP/
BACK in steps 1–2 to display the PictBridge menu (see To print the print order created with K PRINT
“Printing the DPOF Print Order,” below). Press the se- ORDER (DPOF) in the playback F-mode menu
lector up or down to highlight PRINT WITH DATE s (pg. 89):
and press MENU/OK to return to the PictBridge display
(to print pictures without the date of recording, select 1 InBACKthetoPictBridge display, press DISP/
open the PictBridge menu.
PRINT WITHOUT DATE).
PICTBRIDGE
2 highlight
Press the selector up or down to
u PRINT DPOF.
YES CANCEL
64
Printing Pictures via USB
1 Notes
4 Press MENU/OK to start printing. • Print pictures from a memory card that has been for-
matted in the camera.
During Printing • If the printer does not support date printing, the
The message shown at right PRINTING PRINT WITH DATE s option will not be available in
is displayed during printing. the PictBridge menu and the date will not be printed
Press DISP/BACK to cancel be- on the pictures in the DPOF print order.
fore all pictures are printed • When pictures are printed via direct USB connection,
(depending on the printer, CANCEL page size, print quality, and border selections are
printing may end before the made using the printer.
current picture has printed).
If printing is interrupted, press a to turn the camera
off and then on again.
Connections
65
Printing Pictures via USB
1 play
Press the selector left or right to dis-
a picture you wish to include in
or remove from the print order.
66
Printing Pictures via USB
Connections
tion, page size, print quality, and border selections
are made using the printer.
67
Printing Pictures via USB
68
Viewing Pictures on a Computer
The supplied software can be used to copy pictures to a computer, where they can be stored, viewed,
organized, and printed. Before proceeding, install the software as described below. Do NOT connect the
camera to the computer until installation is complete.
Connections
• Built-in USB port recommended. Operation is not guaranteed with other USB ports.
• Internet connection (broadband recommended) required to install .NET Framework (if necessary), to use
Other
auto update feature, and when performing such tasks as sharing pictures on-line or via e-mail.
• Installation of .Net Framework 3.5 SP1 required to use upload picture feature and MapViewer.
1 Other versions of Windows are not supported. Only pre-installed operating systems are supported; operation is not
guaranteed on home-built computers or computers that have been upgraded from earlier versions of Windows.
2 Recommended when displaying HD movies.
69
Viewing Pictures on a Computer
2 Start the computer. Log in to an account with administrator privileges before proceeding.
3 Exit any applications that may be running and insert the installer CD in a CD-ROM drive.
Windows 7/Windows Vista
If an AutoPlay dialog is displayed, click SETUP.EXE. A “User Account Control” dialog will then be displayed;
click Yes (Windows 7) or Allow (Windows Vista).
The installer will start automatically; click Install MyFinePix Studio and follow the on-screen in-
structions to install MyFinePix Studio.
If the Installer Does Not Start Automatically
If the installer does not start automatically, select Computer or My Computer from the Start menu, then
double-click the FINEPIX CD icon to open the FINEPIX CD window and double-click setup or SETUP.EXE.
4 Ifplete
prompted to install Windows Media Player or DirectX, follow the on-screen instructions to com-
installation.
5 CD
Remove the installer CD from the CD-ROM drive when installation is complete. Store the installer
in a dry location out of direct sunlight in case you need to re-install the software. The version
number is printed at the top of the CD label for reference when updating the software or contacting
customer support.
Installation is now complete. Proceed to “Connecting the Camera” on page 73.
70
Viewing Pictures on a Computer
2 CD
After starting the computer and quitting any applications that may be running, insert the installer
in a CD-ROM drive and double-click Installer for Mac OS X.
3 administrator
An installer dialog will be displayed; click Installing FinePixViewer to start installation. Enter an
name and password when prompted and click OK, then follow the on-screen instruc-
tions to install FinePixViewer. Click Exit to quit the installer when installation is complete.
Connections
71
Viewing Pictures on a Computer
4 Remove the installer CD from the CD-ROM drive. Note that you may be unable to remove the CD
if Safari is running; if necessary, quit Safari before removing the CD. Store the installer CD in a dry
location out of direct sunlight in case you need to re-install the software. The version number is
printed at the top of the CD label for reference when updating the software or contacting customer
support.
5 Mac OS X 10.5 or earlier: Open the “Applications” folder, start Image Capture, and select Preferences…
from the Image Capture application menu. The Image Capture preferences dialog will be displayed;
choose Other… in the When a camera is connected, open menu, then select FPVBridge in the
“Applications/FinePixViewer” folder and click Open. Quit Image Capture.
Mac OS X 10.6: Connect the camera and turn it on. Open the “Applications” folder and start Image
Capture. The camera will be listed under DEVICES; select the camera and choose FPVBridge from
the Connecting this camera opens menu and click Choose. Quit Image Capture.
Installation is now complete. Proceed to “Connecting the Camera” on page 73.
72
Viewing Pictures on a Computer
2 USB
Turn the camera off and connect the supplied
cable as shown, making sure the connec-
tors are fully inserted. Connect the camera di-
rectly to the computer; do not use a USB hub
Connections
or keyboard.
73
Viewing Pictures on a Computer
74
Using the Menus: Shooting Mode
The F-mode and shooting menus contain settings for a wide range of shooting conditions.
2 highlight
Press the selector up or down to
the desired menu item. 5 lighted
Press MENU/OK to select the high-
option.
3 tions
Press the selector right to display op-
for the highlighted item.
6 menu.
Press DISP/BACK to exit from the
Menus
75
Using the Menus: Shooting Mode
N ISO
Control the camera’s sensitivity to light. Higher values can be used to reduce blur when lighting is
poor; note, however, that mottling may appear in pictures taken at high sensitivities. If AUTO, AUTO
(800), or AUTO (400) is selected, the camera will adjust sensitivity automatically in response to shoot-
ing conditions. The maximum values that will be selected by the camera at settings of AUTO (800)
and AUTO (400) are 800 and 400 respectively. Settings other than AUTO are shown by an icon in the
display.
1 Note
Sensitivity is not reset when the camera is turned off or another shooting mode is selected.
76
Using the Menus: Shooting Mode
O IMAGE SIZE
Choose the size and aspect ratio at which still pic- Aspect Ratio
tures are recorded. Large pictures can be printed Pictures with an aspect ratio of 4 : 3 have the same
at large sizes with no drop in quality; small pic- proportions as the camera display. Pictures with an
tures require less memory, allowing more pictures aspect ratio of 3 : 2 have the same proportions as a
to be recorded. frame of 35-mm film, while an aspect ratio of 16 : 9 is
suited to display on High Definition (HD) devices.
Option Prints at sizes up to
O4:3 34 × 25 cm (13.5 × 10 in.)
O3:2 34 × 23 cm (13.5 × 9 in.)
O 16 : 9 34 × 19 cm (13.5 × 7.5 in.)
P4:3 24 × 18 cm (9.5 × 7 in.)
P3:2 24 × 16 cm (9.5 × 6 in.) 4:3
P 16 : 9 24 × 13 cm (9.5 × 5.5 in.)
Q4:3 17 × 13 cm (7 × 5 in.)
Q3:2 17 × 12 cm (7 × 4.5 in.)
Q 16 : 9 16 × 9 cm (6.5 × 3.5 in.)
The number of pictures that can be taken at the 3:2 16 : 9
selected setting is shown in the display (pg. 124).
Menus
1 Note
Image size is not reset when the camera is turned off or
another shooting mode is selected.
77
Using the Menus: Shooting Mode
78
Using the Menus: Shooting Mode
Menus
Choose whether the camera automatically detects and
S FACE RECOGNITION sets focus and exposure for human portrait subjects — —
(pg. 84).
P MODE Choose how panoramas are framed (pg. 25). C/D C
Choose the size of the bracketing increment when O is
J AE BKT EV STEPS ±1/3 EV / ±2/3 EV / ±1 EV ±1/3 EV
selected in continuous shooting mode (pg. 87).
79
Using the Menus: Shooting Mode
80
Using the Menus: Shooting Mode
Menus
• At settings other than h, auto white balance is used
with the flash. Lower the flash (pg. 37) to take pic-
tures at other settings.
• Results vary with shooting conditions. Play pictures
back after shooting to check colors in the monitor.
81
Using the Menus: Shooting Mode
82
Using the Menus: Shooting Mode
C PHOTOMETRY F AF MODE
Choose how the camera meters exposure when This option controls how the camera selects the
Intelligent Face Detection is off. focus area when Intelligent Face Detection is off
• o MULTI: Automatic scene recognition is used (pg. 32). Regardless of the option selected, the
to adjust exposure for a wide range of shooting camera will focus on the subject in the center of
conditions. the monitor when macro mode is on (pg. 36).
• p SPOT: The camera meters lighting conditions • r CENTER: The camera focuses on the subject in
at the center of the frame. Recommended when the center of the frame. This option can be used
the background is much brighter or darker than with focus lock (pg. 34).
the main subject. Can be used with focus lock • s MULTI: When the shutter button is pressed
(pg. 34) to meter off-center subjects. halfway, the camera detects high-contrast sub-
• q AVERAGE: Exposure is set to the average for jects near the center of the frame and selects
the entire frame. Provides consistent exposure the focus area automatically (if the focus frame is
across multiple shots with the same lighting, not displayed, select r CENTER and use focus
and is particularly effective for landscapes and lock; pg. 34).
portraits of subjects dressed in black or white. P Press
halfway
PROGRAM SHIFT
Menus
80 F2. 8
Focus frame
83
Using the Menus: Shooting Mode
START TRACKING
left to select tracking. Focus PROGRAM SHIFT
250 F3. 1
will track the subject as it CAPTURE THE FACE
ALONG WITH THE GUIDLINE
moves through the frame. CANCEL
4 Press
INFO.
MENU/OK to display PERSONAL
84
Using the Menus: Shooting Mode
5 Enter
Register.
the following information:
2 highlight
Press the selector left or right to
a face to view or edit.
• NAME: Enter a name of up to 14 characters
and press MENU/OK. 3 Press
INFO.
MENU/OK to display PERSONAL
• BIRTHDAY: Enter the subject’s date of birth and
press MENU/OK.
• CATEGORY: Choose the option that describes 4 ofView the registration or edit as the same way
REGISTER (pg. 84).
your relationship to the subject and press
MENU/OK. A Notes
• Select REPLACING IMAGE to take another face im-
A Notes age and replace the registered image with it.
• If shooting date matches the birthday of the peson • To delete face recognition data, select ERASE from
with the green border during face zoom, Happy S FACE RECOGNITION.
Birthday! will be displayed with the name.
• If D BABY MODE is selected in the shooting mode
and Intelligent Face Detection is on, the camera will
Menus
display the age of a 3 year old or younger child.
• To disable face recognition, set FACE RECOGNITION
to OFF.
85
Using the Menus: Shooting Mode
86
Using the Menus: Shooting Mode
Menus
87
Using the Menus: Shooting Mode
g EXTERNAL FLASH
Choose ON when using an optional flash unit (ex-
cept Fujifilm products) mounted on the camera
hot shoe.
c Cautions
• The flash may not fully light the subject at speeds
faster than 1/1000 s.
• Use auto or custom white balance (pg. 81).
• If the built-in flash is raised when ON is selected for
g EXTERNAL FLASH, the built-in flash will fire once
to provide a signal for the optional flash unit to fire.
• External flash units can be used in P, S, A, M or C
mode.
• Fujifilm external flash units do not require this setting.
a Notes
• The camera can be used with flash units that provide
aperture adjustment, external metering, and sensitiv-
ity control. Some flash units that are designed spe-
cifically for other cameras can not be used.
• For information on Fujifilm external flash units, see
Accessories from FUJIFILM (pg. 110).
88
Using the Menus: Playback Mode
The F-mode and playback menus are used to manage the pictures on the memory card.
4 tions
Press the selector right to display op-
for the highlighted item.
5 highlight
Press the selector up or down to
the desired option.
6 lighted
Press MENU/OK to select the high-
option.
Menus
89
Using the Menus: Playback Mode
I SLIDE SHOW
View pictures in an automated slide show. Choose the type of show and press MENU/OK to start. Press
DISP/BACK at any time during the show to view on-screen help. When a movie is displayed, movie play-
back will begin automatically, and the slide show will continue when the movie ends. The show can
be ended at any time by pressing MENU/OK.
Option Displayed in
NORMAL Press selector left or right to go back or skip ahead one frame. Select FADE-IN for fade transitions between
FADE-IN frames.
NORMAL g
As above, except that camera automatically zooms in on faces selected with Intelligent Face detection.
FADE-IN g
MULTIPLE Display several pictures at once.
1 Note
The camera will not turn off automatically while a slide show is in progress.
90
Using the Menus: Playback Mode
5 highlight
Press the selector up or down to
the desired option.
D PROTECT
Protect pictures from accidental dele-
tion (pg. 95).
Create cropped copies of pictures
G CROP
(pg. 96).
6 lighted
Press MENU/OK to select the high-
option.
O RESIZE
C IMAGE ROTATE
Create small copies of pictures (pg. 97).
Rotate pictures (pg. 98).
F VOICE MEMO Add voice memos to pictures (pg. 99).
Remove face recognition links from
S ERASE FACE RECOG.
Menus
the current image (pg. 87).
Select pictures for printing on DPOF-
K PRINT ORDER
and PictBridge-compatible devices
(DPOF)
(pg. 64).
Choose how High Definition (HD) de-
J DISP. ASPECT
vices display pictures (pg. 100).
91
Using the Menus: Playback Mode
92
Using the Menus: Playback Mode
OK
CANCEL
SET
3 Press MENU/OK.
All items are removed from the up-
load queue.
1 Note
If there are many items in the upload queue when you
Menus
select to remove all items from the queue, it may take
some time to remove them. To cancel, press DISP/BACK.
93
Using the Menus: Playback Mode
YES CANCEL
1 Notes
• Red eye may not be removed if the camera is unable to detect a face or the face is in profile. Results may differ
depending on the scene. Red eye can not be removed from pictures that have already been processed using
red-eye removal or pictures created with other devices.
• The amount of time needed to process the image varies with the number of faces detected.
• Copies created with B RED EYE REMOVAL are indicated by a e icon during playback.
94
Using the Menus: Playback Mode
D PROTECT
Protect pictures from accidental deletion. The following options are available.
■ FRAME ■ SET ALL
Protect selected pictures. Press MENU/OK to protect all SET ALL OK?
IT MAY TAKE A WHILE
■ RESET ALL
Press MENU/OK to remove pro- RESET ALL OK?
IT MAY TAKE A WHILE
Menus
tional images. Press DISP/BACK to exit 3 Caution
Protected pictures will be deleted when the memory
when the operation is complete.
card is formatted (pg. 105).
95
Using the Menus: Playback Mode
G CROP
To create a cropped copy of a picture, play the picture back and select G CROP in the playback menu
(pg. 89).
1 Use the zoom control to zoom in and out and 2 Press MENU/OK to view the copy size.
use the selector to scroll the picture until the Larger crops produce larger copies;
desired portion is displayed (to exit to single- all copies have an aspect ratio of 4 : 3.
frame playback without creating a cropped
copy, press DISP/BACK). 3 Press MENU/OK to save the cropped
copy to a separate file.
Zoom indicator
CROP 1 Note
Navigation window Pictures taken with other cameras can not be cropped.
shows portion of
image currently dis-
YES CANCEL played in monitor
96
Using the Menus: Playback Mode
O RESIZE
To create a small copy of a picture, play the picture back and select O RESIZE in the playback menu
(pg. 89).
1 highlight
Press the selector up or down to
a or b.
2 lighted
Press MENU/OK to select the high-
option.
3 the
Press MENU/OK to copy the picture at
selected size.
Menus
97
Using the Menus: Playback Mode
C IMAGE ROTATE
By default, pictures taken in tall orientation are
displayed in wide orientation. Use this option to
1 picture
Press the selector down to rotate the
90 ° clockwise, up to rotate
display pictures in the correct orientation in the the picture 90 ° counterclockwise.
monitor. It has no effect on pictures displayed on
a computer or other device.
1 Notes
• Protected pictures can not be rotated. Remove pro-
tection before rotating pictures (pg. 95).
• The camera may not be able to rotate pictures cre-
ated with other devices.
98
Using the Menus: Playback Mode
F VOICE MEMO
To add a voice memo to a still picture, select
F VOICE MEMO after displaying the picture in
2 Press MENU/OK to start recording.
playback mode. RECORDING 28s
Time remaining
1 Note
Voice memos can not be added to movies or protect- Blinks red
ed pictures. Remove protection from pictures before
REC RE-REC
recording voice memos (pg. 95).
1 (8Hold the camera at a distance of about 20 cm 3 Press MENU/OK again to end record-
in.) and face the microphone. ing. Recording ends automatically
after 30 seconds.
Microphone
Menus
1 Notes
• If a voice memo already exists for the current picture, a message will be displayed. Select RE-REC to replace the
existing memo.
• Voice memos are recorded as PCM-format WAV files.
99
Using the Menus: Playback Mode
16 : 9
4:3
16 : 9 4:3
1 Note
Photographs with an aspect ratio of 16 : 9 are displayed
full screen, those with an aspect ratio of 3 : 2 in a black
frame.
100
The Setup Menu
Using the Setup Menu
1 Display the setup menu.
1.1 Press MENU/OK to display the
2 2.1
Adjust settings.
Press the selector right to acti-
menu for the current mode. vate the setup menu.
1.2 Press the selector left to high- 2.2 Press the selector up or down
light a left tab. to highlight a menu item.
Menus
2.6 Press DISP/BACK to exit from the
menu.
101
The Setup Menu
102
The Setup Menu
Menus
S CUSTOM RESET displayed, press the selector up or down to highlight OK and — —
press MENU/OK.
Choose whether to add shooting date and time to the pic-
S DATE STAMP T + U / T / OFF OFF
tures.
103
The Setup Menu
N TIME DIFFERENCE
When travelling, use this option to switch the camera clock instantly from your home time zone to the
local time at your destination.
1 and
Specify the difference between local time
your home time zone.
2 Switch between local time and your home
time zone.
1.1 Press the selector up or down To switch between local time and your
to highlight g LOCAL. home time zone, highlight g LOCAL or
h HOME and press MENU/OK.
1.2 Press the selector right to dis- • h HOME: Switch to the time currently se-
play the time difference. lected for F DATE/TIME (see above).
• g LOCAL: Switch to local time. If this option
1.3 Press the selector left or right is selected, g and the time and date will
to highlight +, –, hours, or min- be displayed in yellow for three seconds
utes; press up or down to edit. each time the camera is turned on.
1.4 Press MENU/OK when settings
are complete.
12/31/2050 10 : 00 AM
104
The Setup Menu
Menus
ZOOM (CONTINUOUS) is disabled in the follow-
ing case:
• C / B is selected in the shooting mode.
• An option other than OFF is selected for
I CONTINUOUS.
105
The Setup Menu
Menus
2 Tip: Reactivating the Camera
To reactivate the camera after it has turned off auto-
matically, use the G switch or press the a but- 3 Caution
ton for about a second (pg. 14). Digital zoom produces lower quality images than opti-
cal zoom.
107
The Setup Menu
S DATE STAMP
To add shooting date and time, choose T + U.
To add only shooting date, choose T. When OFF
is selected, no information will be added to the
pictures.
1 Notes
• Added shooting date and time can not be deleted
from the pictures. To take pictures without date and
time, select OFF for S DATE STAMP.
• When the camera clock is not set, setting dialog will
be displayed. Set the date and time (pg. 15).
• When using S DATE STAMP, selecting WITHOUT
DATE for K PRINT ORDER (DPOF) is recommend-
ed (pg. 66).
• Date and time can not be added to the movies and
the panoramas.
108
Optional Accessories
The camera supports a wide range of accessories from FUJIFILM and other manufacturers.
■ Audio/Visual
Standard TV (available from
third-party suppliers)
FINEPIX SL300 Series
FINEPIX SL280 Series
USB-A/V cable FINEPIX SL260 Series
FINEPIX SL240 Series ■ Computer Related
HDTV (available from
third-party suppliers) USB-A/V cable
Technical Notes
SD/SDHC/SDXC
■ Printing memory card
USB-A/V cable SD card slot or card reader
109
Optional Accessories
Shoe Mount Flash EF-20: Hot-shoe clip-on flash, guide number: 20 (ISO 100), compatible with
i-TTL, bounce capability: up to 90°, power source: 2 AA-size 1.5V batteries
110
Caring for the Camera
To ensure continued enjoyment of the product, observe the following precautions.
Storage and Use ■ Condensation
If the camera will not be used for an extended pe- Sudden increases in temperature, such as occur
riod, remove the battery and memory card. Do when entering a heated building on a cold day,
not store or use the camera in locations that are: can cause condensation inside the camera. If this
• exposed to rain, steam, or smoke occurs, turn the camera off and wait an hour be-
• very humid or extremely dusty fore turning it on again. If condensation forms on
• exposed to direct sunlight or very high tempera- the memory card, remove the card and wait for
tures, such as in a closed vehicle on a sunny day the condensation to dissipate.
• extremely cold
Cleaning
• subject to strong vibration
Use a blower to remove dust from the lens and
• exposed to strong magnetic fields, such as near
monitor, then gently wipe with a soft, dry cloth.
a broadcasting antenna, power line, radar emit-
Technical Notes
Any remaining stains can be removed by wiping
ter, motor, transformer, or magnet
gently with a piece of FUJIFILM lens-cleaning pa-
• in contact with volatile chemicals such as pesti-
per to which a small amount of lens-cleaning fluid
cides
has been applied. Care should be taken to avoid
• next to rubber or vinyl products
scratching the lens or monitor. The camera body
■ Water and Sand can be cleaned with a soft, dry cloth. Do not use
Exposure to water and sand can also damage the alcohol, thinner, or other volatile chemicals.
camera and its internal circuitry and mechanisms.
Traveling
When using the camera at the beach or seaside,
Keep the camera in your carry-on baggage.
avoid exposing the camera to water or sand. Do
Checked baggage may suffer violent shocks that
not place the camera on a wet surface.
could damage the camera.
111
Troubleshooting
Power and Battery
Problem Possible cause Solution Page
Charge the battery or insert a fully-charged
The battery is exhausted. 8
The camera does spare battery.
not turn on. The battery is inserted incorrectly. Reinsert in the correct orientation. 10
The battery-chamber cover is not latched. Latch the battery-chamber cover. 11
Warm the battery by placing it in a pocket or
The battery is cold. other warm place and reinsert it in the camera vi
Power immediately before taking a picture.
supply The battery runs There is dirt on the battery terminals. Clean the terminals with a soft, dry cloth. —
down quickly. The camera is in M mode. Select another shooting mode. 22
The battery has reached the end of its charging
The battery has been charged many times. —
life. Purchase a new battery.
u CONTINUOUS is selected for F AF MODE. Select a different focusing option. 83
The camera turns Charge the battery or insert a fully-charged
The battery is exhausted. 8
off suddenly. spare battery.
Charging does Reinsert the battery in the correct orientation
The battery is not correctly inserted. 8
not start. and make sure that the charger is plugged in.
Troubleshooting
Charging is slow. The temperature is low. Charge the battery at room temperature. vi
Battery There is dirt on the battery terminals. Clean the terminals with a soft, dry cloth. —
charger The charging
The battery has reached the end of its charging
lamp lights, but
The battery has been charged many times. life. Purchase a new battery. If the battery still —
the battery does
fails to charge, contact your FUJIFILM dealer.
not charge.
The battery is too hot or too cold. Wait for the battery temperature to stabilize. 129
112
Troubleshooting
Shooting
Problem Possible cause Solution Page
Memory is full. Insert a new memory card or delete pictures. 11, 55
No picture is Memory is not formatted. Format the memory card. 105
taken when There is dirt on the memory card contacts. Clean the contacts with a soft, dry cloth. —
the shutter The memory card is damaged. Insert a new memory card. 11
Taking button is Charge the battery or insert a fully-charged
pictures pressed. The battery is exhausted. 8
spare battery.
The camera has turned off automatically. Turn the camera on. 14
The monitor
The monitor may darken while the flash
goes dark after The flash has fired. 37
charges. Wait for the flash to charge.
shooting.
The camera The subject is close to the camera. Select macro mode.
Troubleshooting
36
Focus does not The subject is far away from the camera. Cancel macro mode.
focus. The subject is not suited to autofocus. Use focus lock. 34
113
Troubleshooting
114
Troubleshooting
Troubleshooting
Continuous
Only one pic- The self timer is on and an option L and N
shooting Turn the self-timer off. 39
ture is taken. are selected in continuous shooting mode.
mode
115
Troubleshooting
Playback
Problem Possible cause Solution Page
Pictures are The pictures were taken with a different make or
— —
grainy. model of camera.
Pictures The picture has been resized or cropped to
Playback zoom
a / b or is from another make or model of — 48
unavailable.
camera.
The camera is in silent mode. Turn silent mode off. 19
No sound in
Playback volume is too low. Adjust playback volume. 107
voice memo
Audio The microphone was obstructed. Hold the camera correctly during recording. 58, 99
and movie
playback. 60,
The speaker is obstructed. Hold the camera correctly during playback.
100
Selected
Some of the pictures selected for deletion are Remove protection using the device with
Deletion pictures not 95
protected. which it was originally applied.
deleted.
File number-
The battery-chamber cover was opened while Turn the camera off before opening the bat-
Frame no. ing is unex- 14
the camera was on. tery-chamber cover.
pectedly reset.
116
Troubleshooting
Connections
Problem Possible cause Solution Page
Monitor is off. The camera is connected to a TV. View pictures on the TV. 61
The camera is not properly connected. Connect the camera correctly. 61
An A/V cable was connected during movie Connect the camera once movie playback
60, 61
playback. has ended.
No picture or
Input on the television is set to “TV”. Set input to “VIDEO”. —
TV sound.
The camera is not set to the correct video stan- Match the camera Q VIDEO SYSTEM set-
103
dard. ting to the TV.
The volume on the television is too low. Adjust the volume. —
The camera is not set to the correct video stan- Match the camera Q VIDEO SYSTEM set-
No color. 103
dard. ting to the TV.
The com-
puter does not
Computer The camera is not properly connected. Connect the camera correctly. 73
recognize the
camera.
Pictures can The camera is not properly connected. Connect the camera correctly. 63
not be printed. The printer is off. Turn the printer on. —
Troubleshooting
Only one copy
PictBridge
is printed.
The printer is not PictBridge-compatible. — —
The date is not
printed.
117
Troubleshooting
Miscellaneous
Problem Possible cause Solution Page
Nothing happens Temporary camera malfunction. Remove and reinsert the battery. 10
when the shutter but- Charge the battery or insert a fully-charged
The battery is exhausted. 8
ton is pressed. spare battery.
The camera does not Remove and reinsert the battery. If the prob-
Temporary camera malfunction. 10
function as expected. lem persists, contact your FUJIFILM dealer.
Date and time added
by S DATE STAMP The camera clock is not correctly set. Reset the date and time. 15
are not correct.
Added shooting date and time can not
Date and time are T + U or T is selected for S DATE STAMP be deleted from the pictures. To take pic-
108
added to the pictures. option. tures without date and time, select OFF for
S DATE STAMP.
FinePixViewer does not support Mac OS X
FinePixViewer can not Some operation systems are not supported by
10.7 or later. Use the application supplied —
be installed or run. FinePixViewer.
with Mac OS X or third-party software.
118
Warning Messages and Displays
The following warnings are displayed in the monitor:
Warning Description Solution
B (red) Low battery. Charge the battery or insert a fully-charged spare bat-
A (blinks red) Battery exhausted. tery.
k Slow shutter speed. Picture may be blurred. Use the flash or mount the camera on a tripod.
s
• Use focus lock to focus on another subject at the
(displayed in red
The camera can not focus. same distance, then recompose the picture (pg. 34).
with red focus
• Use macro mode to focus when taking close-ups.
frame)
Aperture or shutter The subject is too bright or too dark. The pic-
If the subject is dark, use the flash.
speed shown in red ture will be over- or under-exposed.
BLINK DETECTED A subject or subjects may have blinked. Retake the photograph if desired.
FOCUS ERROR
Camera malfunction.
LENS CONTROL ERROR Turn the camera off and then on again, taking care not
TURN THE CAMERA OFF, REMOVE to touch the lens. If the message persists, contact a
LENS CAP OR OBSTRUCTION AND FUJIFILM dealer.
TURN THE CAMERA ON
The memory card is not formatted or the
Troubleshooting
Format the memory card using the K FORMAT op-
memory card was formatted in a computer or
tion in the camera setup menu (pg. 105).
other device.
CARD NOT INITIALIZED Clean the contacts with a soft, dry cloth. If the message
The memory card contacts require cleaning. is repeated, format the memory card (pg. 105). If the
message persists, replace the memory card.
Camera malfunction. Contact a FUJIFILM dealer.
PROTECTED CARD The memory card is locked. Unlock the memory card (pg. 11).
119
Warning Messages and Displays
120
Warning Messages and Displays
Troubleshooting
F CAN NOT ROTATE Movies can not be rotated. —
PRESS AND HOLD
An attempt was made to adjust the volume
THE DISP BUTTON TO Exit silent mode before adjusting the volume.
with the camera in silent mode.
DEACTIVATE SILENT MODE
A connection error occurred while pictures
Confirm that the device is turned on and that the USB
COMMUNICATION ERROR were being printed or copied to a computer or
cable is connected.
other device.
Check printer (see printer manual for details). To resume
PRINTER ERROR
Printer out of paper or ink, or other printer er- printing, turn the printer off and then turn it back on.
PRINTER ERROR ror. Check printer (see printer manual for details). If printing
RESUME? does not resume automatically, press MENU/OK to resume.
121
Warning Messages and Displays
122
Glossary
Digital zoom: Unlike optical zoom, digital zoom does not increase the amount of visible detail. Instead, details vis-
ible using optical zoom are simply enlarged, producing a slightly “grainy” image.
DPOF (Digital Print Order Format): A standard that allows pictures to be printed from “print orders” stored
on a memory card. The information in the order includes the pictures to be printed and the number of
copies of each picture.
EV (Exposure Value): The exposure value is determined by the sensitivity of the image sensor and the amount
of light that enters the camera while the image sensor is exposed. Each time the amount of light doubles, EV
increases by one; each time the amount of light is halved, EV decreases by one. The amount of light entering the
camera can be controlled by adjusting aperture and shutter speed.
HDMI (High-Definition Multimedia Interface): An interface standard for the transmission of images and sound that
adds audio input to the DVI interface used to connect computers to displays.
Motion JPEG: An AVI (Audio Video Interleave) format that stores sound and JPEG images in a single file. Motion JPEG
files can be played in Windows Media Player (requires DirectX 8.0 or later) or QuickTime 3.0 or later.
Smear: A phenomenon specific to CCDs which causes white streaks to appear when very bright light sources, such
as the sun or reflected sunlight, appear in the frame.
White balance: The human brain automatically adapts to changes in the color of light, with the result that objects
that appear white under one light source still appear white when the color of the light source changes. Digital
cameras can mimic this adjustment by processing images according to the color of the light source. This process
is known as “white balance.”
Appendix
123
Memory Card Capacity
The following table shows the recording time or number of pictures available at different image sizes.
All figures are approximate; file size varies with the scene recorded, producing wide variations in the
number of files that can be stored. The number of exposures or length remaining may not diminish
at an even rate.
Medium 4 GB 8 GB
O FINE NORMAL FINE NORMAL
O4:3 570 1120 1170 2310
O3:2 630 1250 1310 2580
O 16 : 9 750 1470 1550 3040
Photographs
124
Specifications
System
Model Digital Camera FinePix SL300/SL280/SL260/SL240 Series
Effective pixels 14 million
CCD 1/
2.3 -in., square-pixel CCD with primary color filter
Appendix
f=4.3 mm–103.2 mm (35-mm format equivalent: 24 mm–576 mm)
Digital zoom • Still pictures: approx. 6.7 × (SL300 series: up to 201 × / SL280 series: up to 187.6 × / SL260 series: up to 174.2 × /
SL240 series: up to 160.8, with optical zoom)
• Movies: approx. 3 × (h 1280)/approx. 2 × (f, g)
Aperture F3.1/F8* (wide angle), F5.9/F8/F20* (telephoto), *uses Neutral Density (ND) filter
125
Specifications
System
Focus range (distance from Approx. 40 cm (1.3 ft.)–infinity (wide angle); approx. 2.8 m (9.1 ft.)–infinity (telephoto)
front of lens) • Macro: approx. 7 cm–3.0 m/2.7 in.–9.8 ft. (wide angle); approx. 2.0 m–3.0 m/6.5 ft.–9.8 ft. (telephoto)
• Super macro: approx. 2 cm–100 cm/0.7 in.–3.2 ft. (wide angle)
Sensitivity Standard output sensitivity equivalent to ISO 64, 100, 200, 400, 800, 1600, 3200, 6400 (3200 and 6400
available only at image sizes Q); AUTO, AUTO (400), AUTO (800)
Metering 256-segment through-the-lens (TTL) metering; MULTI, SPOT, AVERAGE
Exposure control Programmed AE, shutter-priority AE, aperture-priority AE, and manual exposure
Exposure compensation –2 EV – +2 EV in increments of 1/3 EV (P, S, and A modes)
Scene modes B (ZOOM BRACKETING), C (NATURAL & N), D (NATURAL LIGHT), C (PORTRAIT),
D (BABY MODE), K (SMILE&SHOOT), M (LANDSCAPE), N (SPORT), O (NIGHT),
H (NIGHT (TRIPOD)), P (FIREWORKS), Q (SUNSET), R (SNOW), S (BEACH), U (PARTY),
V (FLOWER), W (TEXT)
Scene recognition Available (camera automatically selects b, c, d, e, f, or g)
Picture stabilization Optical stabilization, CCD shift
Blink detection Available
Shutter speed (combined • P, S, A, M: 8 s – 1/2,000 s • O: 1/8 s – 1/2,000 s • H: 3 s – 1/1,500 s
mechanical and electronic • P: 8 s – 1/2 s 1 1
• Other modes: 4 s – 2,000 s
/ /
shutter)
Continuous • I: up to 1.2 fps; max. 6 frames • O: up to 1.2 fps; max. 3 frames
• N: up to 1.2 fps; maximum number of frames varies with image size and available memory
• L: up to 1.2 fps; last 6 frames recorded • K: up to 3.3 fps; max. 20 frames; size P
• J: up to 8 fps; max. 40 frames; size Q
Bracketing ±1/3 EV, ±2/3 EV, ±1 EV
Focus • Mode: CENTER/MULTI/AREA/CONTINUOUS/TRACKING
• Autofocus system: Contrast-detect TTL AF
White balance Automatic scene detection; six manual preset modes for direct sunlight, shade, daylight fluorescent,
warm white fluorescent, cool white fluorescent, and incandescent lighting; custom white balance
Self-timer Off, 2 sec, 10 sec
126
Specifications
System
Flash Manual pop-up flash with CCD-metered auto flash control (using monitor pre-flashes); effective range
when sensitivity is set to ISO800 is approx. 40 cm–8.0 m/1.3 ft.–26.2 ft. (wide angle) or 2.5 m–4.1 m/8.2 ft.–
13.4 ft. (telephoto); effective range in macro mode is approx. 30 cm–3.0 m/0.9 ft.–9.8 ft. (wide angle) or
2.0 m–3.0 m/6.5 ft.–9.8 ft. (telephoto)
Flash modes Auto, forced flash, off, slow synchro (red-eye removal off); auto with red-eye removal, forced flash
with red-eye removal, off, slow sync with red-eye removal (red-eye removal on)
Electronic viewfinder (EVF) 0.2-in. (0.5 cm), 200k-dot color LCD viewfinder
Frame coverage Approx. 97% (shooting), 100% (playback)
Monitor 3.0-in. (7.6 cm), 460k-dot color LCD monitor
Frame coverage Approx. 97% (shooting), 100% (playback)
Movies h 1280 (1,280 × 720/720p)/f (640 × 480/VGA)/g (320 × 240/QVGA); monaural sound; frame rate 30 fps
Input/output terminals
A/V OUT (audio/video output) NTSC or PAL output with monaural sound
HDMI output HDMI Mini Connector
Digital input/output USB 2.0 High Speed; shares A/V OUT connector
Appendix
127
Specifications
Power supply/other
Power sources • NP-85 rechargeable battery
Battery life (approximate num- Battery type Approximate number of frames
ber of frames that can be taken NP-85 (type supplied with camera) 300
with a fully-charged battery)
CIPA standard, measured in B (auto) mode using battery supplied with camera and SD memory card.
Note: Number of shots that can be taken with battery varies with battery charge level and will decline
at low temperatures.
Camera dimensions 122 mm × 93 mm × 100 mm/4.8 in. × 3.6 in. × 3.9 in. (W × H × D), excluding projections
Shooting weight SL300 series
Approx. 510 g/17.9 oz., including battery and memory card
SL280 series
Approx. 510 g/17.9 oz., including battery and memory card
SL260 series
Approx. 510 g/17.9 oz., including battery and memory card
SL240 series
Approx. 510 g/17.9 oz., including battery and memory card
Camera weight SL300 series
Approx. 470 g/16.5 oz., excluding battery, accessories, and memory cards
SL280 series
Approx. 470 g/16.5 oz., excluding battery, accessories, and memory cards
SL260 series
Approx. 470 g/16.5 oz., excluding battery, accessories, and memory cards
SL240 series
Approx. 470 g/16.5 oz., excluding battery, accessories, and memory cards
Operating conditions • Temperature: 0 °C – +40 °C/+32 °F – +104 °F • Humidity: 10% – 80% (no condensation)
128
Specifications
Appendix
129
Specifications
130
Memo
131
7-3, AKASAKA 9-CHOME, MINATO-KU, TOKYO 107-0052, JAPAN
http://www.fujifilm.com/products/digital_cameras/index.html
Please contact your local distributor for repairs and technical support. (see Worldwide
Network list)
Restrictions on Camera Settings
Shooting Mode and Camera Settings
The options available in each shooting mode are listed below.
Shooting mode
SP
Option BMB C D C d K M N O H P Q R S U V WN P S A M F
F ✔ ✔ ✔ ✔ ✔1 ✔1 ✔ ✔ ✔ ✔
F Macro mode G ✔ ✔ ✔ ✔ ✔ ✔ ✔
OFF ✔ ✔ ✔ ✔ ✔ ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔ ✔ ✔ ✔
A ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔
N ✔ ✔ ✔ ✔1 ✔ ✔ ✔ ✔1 ✔ ✔ ✔1 ✔ ✔1 ✔ ✔1
JOFF
O ✔ ✔ ✔1 ✔1 ✔ ✔
N P3 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
Flash 2 K ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔
L ✔ ✔ ✔ ✔1 ✔ ✔ ✔1 ✔ ✔ ✔ ✔1 ✔ ✔1
JON
M ✔ ✔ ✔1 ✔1 ✔ ✔
P3
d Exposure compensation 4 ✔ ✔ ✔
g OFF ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔1 ✔ ✔ ✔1 ✔ ✔ ✔
✔1 ✔1 ✔1 ✔ ✔ ✔ ✔ ✔
Face Detection ON ✔ ✔1 ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔ ✔ ✔ ✔✔ ✔ ✔ ✔ ✔
B RED EYE REMOVAL ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔✔ ✔ ✔ ✔ ✔
OFF ✔ ✔ ✔ ✔1 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
✔ ✔ ✔1 ✔✔ ✔ ✔ ✔ ✔
I ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔✔ ✔ ✔ ✔ ✔
I L ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔✔ ✔ ✔ ✔ ✔
Continuous N ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔✔ ✔ ✔ ✔ ✔
shooting K6 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔✔ ✔ ✔ ✔ ✔
J5 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔✔ ✔ ✔ ✔ ✔
O ✔ ✔ ✔ ✔
c Instant zoom 7 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Restrictions on Camera Settings
Shooting mode
SP
Option BMB C D C d K M N O H P Q R S U V WN P S A M F
J SELF-TIMER ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
AUTO ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1 ✔1
AUTO (800) ✔ ✔
AUTO (400) ✔ ✔
6400 5 ✔ ✔ ✔
3200 5 ✔ ✔ ✔
N ISO 1600 ✔ ✔ ✔
800 ✔ ✔ ✔
400 ✔ ✔ ✔
200 ✔ ✔ ✔
100 ✔ ✔ ✔
64 ✔ ✔ ✔
O ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
O IMAGE SIZE P ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Q ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔9 ✔ ✔ ✔ ✔
h 1280 ✔
O QUALITY f ✔
g ✔
T IMAGE FINE ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
QUALITY NORMAL ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔ ✔ ✔
c ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
P
a ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
FINEPIX COLOR
b ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
C PHOTOMETRY 8 ✔ ✔ ✔ ✔
D WHITE BALANCE ✔ ✔ ✔ ✔ ✔
F AF MODE ✔ ✔ ✔ ✔ ✔
H SHARPNESS ✔ ✔ ✔ ✔
S FACE RECOGNITION ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
Restrictions on Camera Settings
Shooting mode
SP
Option BMB C D C d K M N O H P Q R S U V WN P S A M F
I FLASH ✔ ✔ ✔ ✔
g EXTERNAL FLASH ✔ ✔ ✔ ✔
J AE BKT EV STEPS ✔ ✔ ✔ ✔
K CUSTOM SET ✔ ✔ ✔ ✔
X SET-UP ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
l ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
L DUAL IS
m ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
MODE
OFF ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
C AF ILLUMI- ON ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
NATOR OFF ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔1 ✔ ✔ ✔1 ✔1 ✔ ✔ ✔1 ✔1 ✔ ✔1 ✔ ✔ ✔ ✔ ✔
D DIGITAL ON ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
ZOOM OFF ✔ ✔1 ✔1 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔ ✔ ✔ ✔
E EVF/LCD 30fps ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔ ✔ ✔ ✔1
MODE 60fps ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔1 ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
G OPERATION VOL.
H SHUTTER VOLUME ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔ ✔
I PLAYBACK VOLUME
1 Automatically optimized for selected shooting mode.
2 Flash turns off automatically in super macro mode (G).
3 Lower flash to select P in modes other than D.
4 Disabled if flash fires when set to A or K or if flash is set to N or L and subject is poorly lit.
5 Image sizes over Q are set to Q.
6 Image sizes over P are set to P.
7 Tall (portrait-orientation) framing not available at continuous shooting settings of I, N, L, or O.
8 Fixed at o when Intelligent Face Detection is on.
9 Aspect ratio fixed at 4 : 3.