Beruflich Dokumente
Kultur Dokumente
Faculty of Science
A Thesis in
By
DOCTOR OF PHILOSOPHY
March 2013
To my family and wife
CERTIFICATE OF ORIGINALITY
I hereby declare that this submission is my own work and to the best of my knowledge it
contains no materials previously published or written by another person, nor material which
to a substantial extent has been accepted for the award of any other degree or diploma at
UNSW or any other educational institution, except where due to acknowledgment is made in
the thesis. Any contribution made to the research by others, with whom I have worked at
UNSW or elsewhere, is explicitly acknowledged in the thesis.
I also declare that the intellectual content of this thesis is the product of my own work, except
to the extent that assistance from others in the project’s design and conception or in style,
presentation and linguistic expression is acknowledged.
Signed _______________________
make available my thesis or dissertation in whole or part in the University libraries in all
forms of media, now or here after known, subject to the provision of the Copyright Act 1968.
I retain all proprietary rights, such as patent rights. I also retain the right to use in future
I also authorize University Microfilms to use the 350 word abstract of my thesis in
obtained permission to use copyright material; where permission has not been granted I have
Signed ______________________
Date ________________________
AUTHENTICITY STATEMENT
‘I certify that the Library deposit digital copy is a direct equivalent of the final officially
approved version of my thesis. No emendation has occurred and if there are any minor
Signed ________________________
Date __________________________
iii
ACKNOWLEDGEMENTS
I also owe an enormous debt of gratitude to Associate Professor Rita Khanna for her
constructive discussions, her guidance and continuous encouragement and support to get the
work completed.
I wish to thanks the support from Russell Bush, Technology Manager from Tyco Water for
his contribution and technical expertise and his valuable suggestions.
I also wish to acknowledge the financial support and interest from the Australian Research
Council.
I am extremely grateful to Mr. N. Saha - Chaudhury for his great help in making things
happen in our daily laboratory work. His opportune advice and support in my experimental
work is highly appreciated.
I would like to sincerely thank to Professor Chris Sorrell and Dr. Haiping Sun for their
valuable and constructive coaching during my research work.
And last but not least, I wish to thank to my family for their constant encouragement and
inspiration throughout the course of my project. Very special thanks to my wife Marcela for
her support and inspiration to achieve this result.
iv
LIST OF PUBLICATIONS
Journal Papers
1- Yunes, P. J., Hong, L., Saha-Chaudhury, N., Bush, R. and Sahajwalla, V. Dynamic
Wetting of Graphite and SiC by Ferrosilicon Alloys and Silicon at 1550 °C. ISIJ
International, 2006. 46 (11): p. 2006.
Conference Paper
v
ABSTRACT
This work investigates high temperature interactions of silicon and ferrosilicon alloys with
graphite as well as the reactions occurring in the presence of oxidising gases. These reactions
play a key role in the scrap-melting cupola process. Using the sessile droplet method, the
dynamic wetting of synthetic graphite by liquid ferrosilicon alloys containing 24.7 and 74 %
Si and silicon (98.5 % Si) at 1550 °C was investigated. Silicon 98.5% and ferrosilicon alloys
containing 74 and 24.7% Si showed good wetting behaviour (θ < 90º ) with synthetic graphite
at 1550 °C. Full wetting was observed for silicon 98.5 and ferrosilicon 74 within the first 90
seconds. However, the final contact angle value appeared higher for the low-silicon
ferroalloy and remained steady around 70 degrees during the 2 hours-run. The role of the
interfacial product formed and its relationship with the dynamic wetting phenomena was also
investigated. The formation of SiC at the interface appeared 30 seconds after melting for Si
98.5, while this was observed after 60 seconds for FeSi 74, and after 30 minutes for FeSi
24.7. Further wettability investigations carried out on SiC substrates showed trends similar to
the ones observed on synthetic graphite. Full wetting was observed for Si 98.5 and FeSi 74
after 80 and 90 seconds, while FeSi 24.7 showed a different pattern, since the contact angle
decreased rapidly during the first 10 minutes and remained steady around 40 degrees after
that time. The dynamic wetting appeared to be strongly dependent on the rate of formation of
A kinetic mechanism has been developed for the carbon dissolution phenomena in
ferrosilicon alloys. The overall rate constants at 1550 °C for Si 98.5, FeSi 74 and FeSi 24.7
were determined to be 3.8, 3 and 3.9 x 10-3 (s-1) respectively. These did not vary significantly
across samples under investigation. A rapid increase of carbon pickup was observed during
the initial few minutes and remained fairly constant later on. The faster rate observed in the
vi
case of FeSi 24.7 was explained on the basis of delayed formation of SiC interfacial product
which had a retarding effect on the overall process and dictated carbon transfer.
In depth and detailed investigations were carried out on the effect of the alloy composition,
oxygen partial pressure and flow rate on interactions at 1550 °C . Significant differences were
observed in the weight gain and carbon loss between these three alloys; both decarburisation
and silicon oxidation reactions were found to occur simultaneously. There was a clear
evidence for two rate regimes: the rate of decarburisation was found to be much higher
during the initial 2 minutes and a much slower rate was observed in later stages for all
specimens. These rate regimes were explained in terms of the extent of surface coverage with
the reaction product silica. No significant effect was found on the decarburization rates when
the proportion of oxidizing gas (CO2) was increased from 20 to 100%, indicating that mass
transfer in the gas phase was not a dominant rate controlling step compared to chemical
kinetics. The net weight gain in these alloys was found to be due to the combined influence of
decarburization (weight loss due to the generation of a gaseous product) and silicon oxidation
(weight gain due to silica formation on the sample surface). The results of this investigation
showed that the silicon losses in the cupola process can be better managed by using lower
vii
TABLE OF CONTENTS
PAGE
Certificate of Originality ii
Acknowledgments iv
List of Publications v
Abstracts vi
Chapter 1 Introduction 1
1. Introduction 2
2. Literature Review 7
viii
2.5 Kinetics of oxidation 24
3. 1 Sample selection 51
3.1.5 Alumina 59
ix
3.2.6 Electro Probe Micro Analiser (EPMA) 66
4.1 Study of the dynamic wetting for silicon and ferrosilicon alloys on 73
synthetic graphite
77
4.2 Investigation of the product formed during the interfacial reaction
4.5 Summary 89
5.3 Carbon dissolution from SiC substrates into ferrosilicon and silicon 98
at 1550 °C
x
Chapter 6 Simultaneous decarburization and oxidation reactions 104
occurring in silicon and ferrosilicon alloys. Results and
discussion
6.1 Investigation of weight changes for silicon and ferrosilicon alloys 105
6.2 Study of the carbon loss for silicon and ferrosilicon alloys 107
7.2 Dynamic wetting between molten silicon and ferrosilicon with 127
synthetic graphite
References 133
Appendix 1 Dynamic Wetting for silicon and ferrosilicon alloys in natural 138
graphite.
xi
LIST OF FIGURES
FIGURE PAGE
2-4 Si – C system 12
xii
FIGURE PAGE
xiii
FIGURE PAGE
xiv
FIGURE PAGE
4-13 Still image of liquid silicon (Si 98.5%) droplet on SiC 81-82
substrate
5-1 Carbon pickup from graphite into pure iron at 1550 °C. 92
5-5 (Cs Ct ) 95
Plot of ln vs. time (seconds) for carbon
(Cs Co)
dissolution runs of Si 98.5 at 1550 °C.
5-6 (Cs Ct ) 95
Plot of ln vs. time (seconds) for carbon
(Cs Co)
dissolution runs of FeSi 74 at 1550 °C.
xv
FIGURE PAGE
5-7 (Cs Ct ) 95
Plot of ln vs. time (seconds) for carbon
(Cs Co)
dissolution runs of FeSi 24.7 at 1550 °C.
6-1 a-c % Weight gain for three alloys as a function of time. 106
Oxidising gas 20% CO2, 2% CO, N2-balance was used
at flow rates ranging between 0.5 to 2 L/min.
6.-1d % Weight gain for three alloys during the initial 10 107
minutes. Oxidising gas 20% CO2, 2% CO, N2-balance
was used at flow rates of 2 L/min.
xvi
FIGURE PAGE
6-7 a-c Plot of rate weight change (%/min) vs. Silicon content 118
(wt. %) for the three alloys during the first minutes.
Oxidising gas 20% CO2, 2% CO, N2-balance was used
at flow rates of 1 L/min
xvii
LIST OF TABLES
TABLE PAGE
5-1 a Constant rates and Carbon saturation limits for Si 98.5, 101
FeSi 74 and FeSi 24.7 from synthetic graphite
substrate.
5-1 b Constant rates and Carbon saturation limits for Si 98.5, 101
FeSi 74 and FeSi 24.7 from SiC substrate.
xviii
TABLE PAGE
6-2 Weight gains (%) for different silicon and ferrosilicon 105
alloys during the first minutes. Oxidising gas 20% CO2,
2% CO, N2-balance was used at flow rates ranging
between 0.5 to 2 L/min.
xix
CHAPTER 1
INTRODUCTION
Chapter 1 Introduction
1. Introduction
The cupola furnace is considered the dominant scrap-melting facility used in scrap-iron
foundries, producing approximately two-thirds of molten iron needed for casting [Katz et al
(1999)]. The cupola offers several competitive advantages relative to newer melt-furnaces,
including lower energy and scrap costs, higher tolerance for harmful trace elements, and a
wider allowable range for iron-production rates. One of the advantages of such a furnace is
that counter flow preheating of the charge can occur. In a cupola furnace, upward flowing hot
gases come into close contact with the descending burden, allowing direct and efficient heat
exchange into the metallic charge (iron and steel scrap, iron returns and ferroalloys), which
causes its melting and subsequent interaction with the coke lumps.
Coke that is added as part of the charge plays two important roles. In the cupola process, the
major exothermic reaction involves the carbon contained in the coke and the oxygen in the
blast. The combustion reactions provide the required amount of heat to melt the scrap metal
and keep the liquid bath at the desired temperatures. Carbon from coke also dissolves into the
Silicon is another important alloying elements present in the cast irons, and is plays an
important role in the effective control of iron structure and properties. Silicon is a potent
graphitizer and ferritizer in cast irons, determining whether a particular iron will solidify
carbidic (as in white iron) or graphitic (as in gray and ductile irons). Silicon is added to cast
iron in the ladle for several reasons. It may be added as an inoculant, as an inoculant carrier
for magnesium in ductile iron production, to adjust off analysis, or as an alloy to modify the
properties of iron. Silicon enters in solution readily with liquid iron, thus large quantities of
2
Chapter 1 Introduction
silicon can be added in the ladle, since reaction between silicon and iron is exothermic and
temperature losses are minimum. In addition, silicon alters the equilibrium diagram and
lowers the solubility of carbon in molten iron [Cuppola Handbook (1984)]. Because of the
conditions existing in today’s cupola melt foundries, far more silicon units are purchased and
charged on an annual basis than any other alloying element [Cupola Handbook (1984)].
Silicon is usually added as ferrosilicon lumps, accounting for around 2-3 % of the total
Globally, prices of ferrosilicon have been rising in recent years [Service R.I (2004)]. A
number of factors, such as carbon steel world consumption, production cutbacks, anti-
dumping duties and power prices had have a significant influence on the upward prices trend.
For some local manufacturers, around 20% of added silicon is wasted due to the oxidation
during the melting process [Bush (2003)]. This oxidized silicon is transferred to the slag
waste as silica (SiO2), accounting around 30-40% of the slag bulk volume, altering the slag
basicity and decreasing the refractory life span. To offset some of the damage to the
refractory, some limestone is added but this action tends to increase costs and slag volume.
The cost of the ferrosilicon consumption of cast iron produced was around AUD 30/ton. It
also added significantly to the cost of the refractory consumption (AUD 5/ton) as well as the
slag disposal (AUD 1/ton) which are likely to increase. Further, the addition of limestone
The fundamental understanding of the ferrosilicon / graphite and the ferrosilicon / gas phase
interactions during the melting process will bring a positive benefit to the foundries. The
minimizing the generation of industrial waste and improving the control of the composition
3
Chapter 1 Introduction
for the final product. In addition, the higher silicon losses, the higher the silica formed and
the greater slag volume, incurring on additional cost of handling and removing it to the
landfills. In basic slag cupola process, any increasing of silica content (acid oxide), it will
bring decreases of the slag basicity. Managing this very important factor, would extend
knowledge for understanding the interfacial reaction and wettability at the solid/liquid
interface. Although a large body of work has investigated the wettability for silicon and
ferrosilicon on SiC, the dynamic wetting and the associated interfacial phenomena of the
Carbon dissolution phenomena also take place during the ferrosilicon – graphite interactions.
This is a key reaction for the cupola process, since the molten ferrosilicon droplets are
interacting with coke lumps while descending to the furnace well. The kinetic mechanism of
carbon dissolution in liquid iron had been extensively investigated, but it has been limited for
silicon contents less than 10%, since the silicon content during the iron and steel making
As outlined on section 1.1, the interaction of ferrosilicon alloy with coke and the gaseous
phase plays a key role on the silicon recovery. There are several aspects to consider during
these interactions and this work aims to provide a better understanding to these key issues.
4
Chapter 1 Introduction
and carburization.
This project aims to provide fundamental understanding of the ferrosilicon reactions during
the melting process. Reactions involving ferrosilicon strongly affect the silicon loss and
product composition in the scrap melting process. Fundamental knowledge of the ferrosilicon
interaction with the gas phase and graphite during the melting would directly benefit
5
CHAPTER 2
LITERATURE REVIEW
6
Chapter 2 Literature Review
2. Literature Review
A review of the literature relevant to this project is presented in this chapter. A brief outline
of the cupola process and the main reactions involved are discussed. In addition,
thermodynamic analysis of the system, wettability studies and reaction kinetics have been
detailed.
The cupola is a vertical, cylindrical shaft furnace similar to the blast furnace. It differs,
however, with respect to the functions served and the type of charges used. Pig iron, scrap
iron and scrap steel in the cupola replace the iron ore of the blast furnace, and efficient
conversion melting rather than ore reduction is the principal function of the cupola. An
As in the case of blast furnace, the counter-flow preheating of the charge material is inherent
part of the melting process in the cupola. The upward flowing hot gases come in close contact
with the descending burden allowing direct and efficient heat exchange to take place. The
running or charge coke is also preheated, which aids in the combustion process as it reaches
the combustion zone to replenish fuel consumed from the coke bed. Alternating layers of
coke, flux and metal are deposited in the cupola so that the process of combustion, heat
transfer and melting can take place. In the beginning, a bed of coke is placed in the lower
portion of the shaft and ignited. Metallic charge, fluxes, ferroalloys and fuel are added in
alternate layers, or mixed are charged and blast air is introduced into the bed, melting the
charge. Once the process starts it can be continued for a long period of time.
7
Chapter 2 Literature Review
The five major zones, which can be easily distinguished, are: preheating, melting, reduction,
oxidation and the well zone. Zone distribution and temperature profile are shown in Fig 2.2.
The zones of main interest for the present project are the melting and oxidation zones;
8
Chapter 2 Literature Review
Metallic
Charging door
charge,coke and
limestone and
ferroalloys CO2(g)
Preheat zone
T = 400 – 1200 °C
Melting zone
T = 1090 –1320 °C
T = 1700 – 2100 °C
O2 (Air)
Well zone T = 1540 – 1570 °C
Tap hole
Slag hole
The melting zone is the region from the top of the coke bed to the point where melting first
occurs in the metallic charge. Hot gases coming from the upper reduction zone supply the
heat necessary to melt the metal. The slag also begins to melt in this region. The liquid iron
helps to liquidify more of the steel and some carbon is picked up by the steel from either the
stack gases or coke in the preheat zone and serves to lower melting point of the steel.
The primary function of the oxidation zone is to supply energy for the additional superheating
of the molten iron and to provide hot gases to superheat, melt and preheat charge materials in
the zones above the tuyeres. These are the regions where the blast enters the cupola and
reacts with the hot coke to form CO and CO2. (Eq. 2.1, 2.2)
9
Chapter 2 Literature Review
The gas temperatures in this zone rise and fall rapidly and range from 1700 to 2100°C. At
these temperatures, Oxygen reacts rapidly with coke and CO until it is reduced to 1-2 %
The study of phase diagrams is very useful to explain the chemical behavior at the liquid /
solid interface, liquid formation and solid-liquid solubilities. It is also a valuable tool for
predicting the potential for a particular combination of oxides, carbides or other compound
and liquid metal. In recent years, considerable amount of work has been published on the Fe-
Si, Si-C and Fe-Si-C systems, based on more accurate thermodynamic calculations and new
experimental data. Due to its important role in steelmaking process and cast iron foundry,
these systems have been the subject of many thermodynamic studies. A summary of some of
the most recently published work on these systems is presented in the next sections.
The Fe-Si system has been studied by a number of authors [Kubacheski (1982)][Hultgren et
Although some authors had reviewed and proposed some changes, the general shape of these
diagrams has not changed substantially. Most of the changes are related with the nature of
reactions occurring in the bcc-Fe-rich solution [Lacaze (1991)]. The silicon rich side has not
received the same level of attention, however this region is reasonably well known.
10
Chapter 2 Literature Review
Kubachewski [Kubacheski (1982)] proposed a diagram for the Fe-Si system (Fig 2-3). In the
solid state, there are only three stable phases, which are FeSi, Fe3Si7 and Si, although the
second one is a low-temperature form of FeSi2. A ferrosilicon alloy with silicon content
higher than 50 at % (= 33.5 wt %) will consist in a mixture of these phases, which are often
found as grains. From 50 at% to 66.7% the low temperature equilibrium phases are FeSi and
FeSi2; above 66.7 at %, FeSi2 and silicon. Lacaze and Sundman [Lacaze and Sundman
(1991)] determine precisely the partial liquidus surface in the iron corner, optimizing the
Experimental work by Schürmann and Hensgen [Schürmann and Hensgen (1962)] on the Fe-
FeSi system confirms the liquid/solid equilibrium determined previously, however, they
considered only the DO3 modification of the bcc phase and adopted previous views that
ordering was a first order reaction [Hultgren et al (1973)]. The gamma loop has been studied
by Fischer and Uberoi [Fischer and Uberoi (1962)] and Übelacker [Übelacker (1967)], whose
results are in good agreement. Although there is a general agreement about the nature of
reactions involving different sicilides, various temperatures are not so well established and
the values proposed by Kubachewski [Kubacheski (1982)] are compromised at some extent.
Figure 2-4 shows the phase diagram for the Si-C system, summarizing the available data
from literature [Hoffman et al (1999)]. The system forms a peritectic at T ~ 2800 °C. The
solubility of C in liquid Si is quite low, reaching the maximum value when C (At%) is about
15%. For pure Si (< 50 At%) and temperatures above 1414 °C, there are 2 phases in the
system: SiC and liquid phase. After solidification, SiC and Si appear as two independent
phases.
11
Chapter 2 Literature Review
12
Chapter 2 Literature Review
Ternary phase diagram for Fe-Si-C at 1000 °C (Fig 2-5) had been derived from the published
work by Sorrell [Sorrell (1995)] For Fe-rich compositions (to the left of the Fe5Si3-SiC tie
line), the recrystallization of liquid will result in the formation of Fe5Si3 and α Fe. For Si-rich
compositions (to the right of Fe5Si3 – SiC tie line), the recrystallization of liquid will result in
the formation of Fe5Si3 and FeSi. Figures 2-6 and 2-7 provide the projection for metastable
and stable diagrams for the Fe-rich corner. Despite the amount of previous work, there are
still some discrepancies regarding to some lines on the Fe-Si-C system. In one of the studies,
Miettinen [ Miettinen (1998)] reassessed some thermodynamic phase data, although the Fe-
13
Chapter 2 Literature Review
14
Chapter 2 Literature Review
Considering the heterogeneous nature of the present system, there are a number of reactions
involve more than one phase and there are distinct phase boundaries. In any given system, the
rate of reaction at given time depends basically on three factors, namely, the nature of the
system, the time of reaction and the temperature. One of the main aims of a kinetic study is
frequently the establishment of a rate law, which can be used in prediction of reaction under
The dissolution of solid into a liquid phase can occur by diffusion, convection and eddy
diffusion (turbulence). Since there is absence of stirring, the fluid layer in contact with the
solid surface cannot slip past the solid, and is, therefore, stagnant. The liquid film adjacent to
the solid may be saturated, providing the release of atoms or molecules from the bulk solid is
sufficiently rapid. The solute diffuses into the bulk liquid from the saturated layer. Most of
the concentration drop takes place within a relatively finite thin layer known as the boundary
layer. The boundary layer thickness (δ) is defined as the distance by which 99% drop is
achieved. Since the fluid layer adjacent to the solid surface cannot slip past the solid, there
must also be a velocity profiles so that flow near the boundary layer is laminar, therefore:
15
Chapter 2 Literature Review
C i
J ix = C vix = - Di Ci C vx - E D (2-3)
x
x
i i
where,
C = concentration of species i
i
Di = diffusion coefficient of I
E D = eddy diffusivity
But when the flow near the boundary layer is laminar, we have:
( v x )x =0 = 0
( E D )x =0 = 0
So, for diffusion across the boundary layer, we have the Fick’s law
Cs Co
J D (2-4)
dissolved in time dt to change the concentration by an amount of dC. If V is the total volume
dn V dC D
. ( Cs – Co) (2-5)
dt A dt
which gives,
D A
ln ( Cs – Co ) = - t+I (2-6)
V
I = integration constant
16
Chapter 2 Literature Review
(Cs Co ) DA
exp t (2-7)
(Cs Ci ) V
DA
Co = Cs – ( Cs – Ci) exp t (2-8)
V
DA
Co = Cs – ( Cs – Ci) 1 t (2-9)
V
(Ci Co )
α= , (2-10)
(Ci Cs )
(Cs Co )
1- α = (2-11)
(Cs Ci )
-ln ( 1- α) = kt (2.12)
DA
Where k = , corresponding with a first order equation.
V
The mass transfer of carbon dissolution from graphite into liquid iron and the chemical
reaction govern the interfacial phenomena to some extent. The rate of mass transfer and the
rate of chemical reaction can be expressed as follow (2-13) [Gaskell (1995)], [Levenspiel
(1976)] :
C
Jc JD (2-13)
t
Where,
17
Chapter 2 Literature Review
JD = rate of diffusion
m
And Jc K C n i (2-14)
i 1
2C 2C 2C
JD D 2 2 2 (2-15)
x y z
D = diffusion coefficient
Various factors affecting the carbon dissolution from graphite into molten iron have been
(2003)], using both experimental and theoretical approaches. The goal of those studies had
Those researches had been conducted under different experimental conditions. Dahlke et. al.
[Dahlke et al (1955)] studied the carbon dissolution by immersing graphite rods into Fe-C
melts for different lengths of time. They found the change of the bath composition was
controlled by mass transport within the metal. Further studies by Wright and Baldock
[Wright and Baldock (1988)] found the rate of carbon dissolution from a rotating graphite
disk into different melts was limited by carbon diffusion from the graphite melt/interface to
18
Chapter 2 Literature Review
Some work had been carried out under stirring and the findings showed the mass-transfer
coefficient for carbon dissolution from graphite was a function of the peripheral velocity of
the rotating cylinder. It was also found the rate of carbon dissolution from graphite to the Fe-
C melts was controlled by carbon diffusion (mass transfer) from the interface (between the
solid graphite and bulk liquid) when the Reynolds number ranged from 790 – 18 000 [Olson
et al (1966)].
Kosaka et al [Kosaka and Minowa (1968)] measured the carbon transfer coefficient in the
temperature range from 1270 – 1550 °C. They also calculated the mass transfer coefficient
assuming liquid-mass transfer controlled the process of the carbon dissolution. In addition,
they immersed a rotating graphite cylinder into the iron melts. The mass-transfer coefficient
obtained from a first –order equation was ranging from 0.8 – 3.6 m/s at a stirring velocity of
48-52 cm/s and between 0.22 – 1.8 m/s at stirring velocity of 4.5-33 cm/s in an induction
furnace.
Oersten et al [Oersten et al ( 1986) ] used the rotating cylinder method to obtain the rate
limitation for carbon dissolution. In this investigation, interfacial phenomena were taken into
account as phase boundary reactions. It was estimated that the rate constant of the phase-
boundary reaction was ~ 0.5 x10-2 m/s, which was 16 to 33 times larger than the overall
mass-transfer rate constant in the liquid side obtained from experiments. Therefore, they
arrived at the conclusion that the liquid-side mass transfer rate limitation was the controlling
More recently, Wu et al [Wu and Sahajwalla (2000) ] investigated the carbon dissolution
from graphite and coals using an induction furnace. It was confirmed mass transfer in the
liquid boundary layer adjacent to the solid/liquid interface controlled the carbon dissolution
from graphite. However, carbon dissolution from coals is most likely to be governed by a
19
Chapter 2 Literature Review
Zhao [Zhao (2003)] found the apparent carbon dissolution constant rate in pure iron was
0.0419 s-1. (Fig 2-8) Carbon dissolution from graphite is thought to be a two-step process [
1. Dissociation of carbon atoms from its crystal site in the graphite into the carbon/melt
interface.
2. Mass transfer of carbon atoms through the adjacent boundary layer into the bulk
liquid iron.
The carbon dissolution in iron is controlled by a mass-transfer in liquid side mechanism [Wu
and Sahajwalla (2000)]. It had been found the dissolution rates are governed by the diffusion
of carbon from the metal-carbon interface to the bulk liquid through a boundary layer
[Zhao(2003)].
-1
y = -0.0416x
R² = 0.98
-2
ln(Cs-Ct/Cs-Co)
-3
-4
-5
-6
-7
Time(seconds)
Figure 2-8: Apparent carbon dissolution rate constant of iron in synthetic graphite. [Zhao
(2003)]
20
Chapter 2 Literature Review
Table 2-1. Experimental and calculated values of carbon solubility in liquid silicon
equilibrated with SiC.
The interaction in the system Si/SiC was also studied by Naidich [Naidich (1981)]. It was
found that at temperatures close to the silicon melting point, the latter dissolves small
amounts of carbon. Due to current demand by stainless steel producers specifying very low
carbon (< 200 ppm) in ferrosilicon (e.g. FeSi75), carbon solubility plays an important role for
ferrosilicon producers,
21
Chapter 2 Literature Review
Ottem [Ottem (1993)] determined the solubility of carbon in silicon and FeSi alloys at
different temperatures (Fig. 2-9). The carbon solubility in ferrosilicon was found to decrease
when the iron content had increased in the ferroalloy. At 1550 °C, the solubility of carbon in
Si was found to be around 150 – 170 ppm, while values for FeSi75 (100 – 120 ppm) and
FeSi65 (70 – 75 ppm).Carbon solubility in FeSi 65 seems to be half of that in pure silicon.
However, at 1614° C, the solubility of C on FeSi started to increase when %Si was below 50,
reaching solubility values similar to ferroalloys with 90% wt Si (Fig 2-10). Ottem [ Ottem
(1993)] also studied the effect of aluminium contained in (ferro) silicon. Aluminium also has
some effect on the carbon solubility, when it is beyond certain levels. (Fig 2-11)
Klevan [Klevan (1997)] found the following equations for the solubility of carbon in silicon
Klevan [Klevan (1997)] found contents of 700 -1100 ppmw C when the metal was tapped
from the furnace. Statistical analyses of 779 shipments over 3 years found that the carbon
content dropped to an average of 300 ppmw C, after vesting, crushing and screening the
material. It was found that the carbon, which precipitates as SiC particles as the temperature
drops during tapping and handling, is physically removed as particles to a fairly large extent.
22
Chapter 2 Literature Review
0.04
0.035 1547
1614
0.03 1652
1674
0.025
C (wt%)
0.02
0.015
0.01
0.005
0
30 40 50 60 70 80 90 100
Si (wt%)
[Ottem (1993)]
Figure 2-10: Solubility of carbon in silicon Figure 2-11: The effect of Al on the
and FeSi at different temperatures. solubility of C in pure silicon and
[Ottem (1993)] FeSi at 1550 °C [Ottem (1993)]
23
Chapter 2 Literature Review
The oxidation of metals has been investigated by different methods, including determination
of the change in thickness of the scale, in weight (mass) of the metal sample or in volume of
the surrounding gas. Most quantitative data have been obtained as weight change (Δ m).
Kinetic theory has been developed to determine the relationship between oxidation and time.
Different correlations have been found empirically and relate Δ m and time t. Some
m kt linear (2-18)
( m ) 2 kt parabolic (2-19)
( m ) 3 kt cubic (2-20)
24
Chapter 2 Literature Review
The type of time relationship that can be applied to a given metal or alloy depends largely on
the thickness of the film already formed, that is on time and temperature.
Decarburization with carbon dioxide had been investigated for various reaction conditions. A
The interfacial rate constants for the decarburization of carbon-saturated liquid iron alloys by
CO2 were first reasonably well established by the work of Sain and Belton [Sain and Belton
(1976)],[Sain and Belton (1978)]. They used jets of CO2 containing gas mixtures impinging
onto the surfaces of inductively stirred iron-carbon alloys and maintained carbon saturation
by having a disk cemented onto the bottom of the crucible containing liquid iron. This
maintained a high driving force for liquid-phase mass transfer of carbon, and thus also
eliminated it as a rate controlled step. Reaction rates were determined from the weight losses
Mannion and Freuhan [ Mannion and Freuhan (1989)] used a similar technique but
determined the rates from the production of CO, measured by continuous mass-spectrometric
analysis of the reacted gas stream. The data are consistent with the first-order rate constants,
25
Chapter 2 Literature Review
mol
Where the first-order rate constant k is expressed in 2
cm atms
For the reaction of liquid iron alloy with gases, kinetic mechanisms have been studied for
gas oxidation of iron based multi-component liquid metal. For liquid iron with high
concentration of carbon and silicon, the oxidation rates of carbon dioxide gases was
controlled by diffusion in the gas phase. It was found the oxidation did not occur
simultaneously for both elements, although the content of each individual component in the
metal was far above the equilibrium level. The thermo chemical driving forces play an
important role in some reactions i.e. the oxidation of each component occurs in
other than carbon was also found to be limited by transport of oxidizing gas.
Baker [Baker et al (1967)] used the levitation technique to investigate the decarburization of
iron – carbon alloys at 1600 ºC. The carbon dioxide content was varied from 1 to 100 %,
using helium as the carrier gas. The results were reported for gas velocity of the order of 12.5
63 cm/s. The observed rates of decarburization were shown to be independent of the carbon
concentration of the melt for carbon contents as low as 0.5 wt%. These authors developed a
relationship for the gas phase flux of carbon dioxide to the surface using stagnant boundary
layer theory. They found that the decarburization rate was largely limited by mass transfer in
Some recent evidence suggests that their decarburization rates at higher velocity under a
100% carbon dioxide atmosphere were likely to have encountered some resistance from
chemical reaction kinetics. The role of sulphur as a retarding agent during the decarburization
is well known and that might have taken some part for their observed rate being lower than
26
Chapter 2 Literature Review
Swisher and Turkdogan [Swisher and Turkdogan (1967)] investigated the rate of
decarburization at 1580 °C using CO-CO2 gas mixtures preheated up to 1300 °C. The
crucible technique was used with exit gas velocity from the lance of the order of 200 cm/s.
The authors reported that the rate of decarburization was independent of the melt carbon
composition until 0.2 wt% carbon in the metal. This precludes the influence of liquid phase
resistance to decarburization. These authors also found that the gas phase mass transfer
coefficient at 2.6 cm/s gave the large values for the conceptual boundary layer thickness (1.33
cm). It was argued that the mass transfer coefficient and the lance exit velocities greater than
200 cm/s were not comparable. They came to the conclusion that their decarburization rates
were not consistent with mass transport in the gas phase and therefore, limited by interfacial
chemical kinetics. The proposed mechanism for the overall chemical reaction was considered
to be
The dissociation and adsorption of carbon dioxide on the melt given by equation (2-25) was
proposed as the rate limiting step in the decarburization process. The model proposed by
Swisher and Turkdogan [Swisher and Turkdogan (1967)] also took into consideration the
retarding influence of surface active species. It also showed that the model was equally
applicable to the dissolution of adsorbed species into melts. For both cases, the authors
proposed that the rates of reaction were proportional to the fraction of vacant sites on the
surface. The role of surface active species was to render surface area unavailable for reaction.
27
Chapter 2 Literature Review
Freuhan and Martonik [Freuhan and Martonik (1974)] using a heat transfer analogy
recomputed the mass transfer coefficients for similar experimental conditions used for
Swisher et al [Swisher and Turkdogan (1967)] and obtained a comparable value with that
experimentally obtained for latter authors. There was enough evidence to establish that the
gas phase mass transfer offered significant resistance to the decarburization rate for this work.
Freuhan and Martonik [Freuhan and Martonik (1974)] carried out this study using carbon
dioxide and hydrogen at 1527 °C. Their work was aimed at resolving discrepancies with
previous work from Baker [Baker et al (1967)] and Swisher et al [Swisher and Turkdogan
(1967)] , which reported conflicting rate limiting mechanism above 1400 °C . The authors
choose conditions that characterize gas phase mass transfer mechanisms for typical
experimental geometries such as flow over a flat plate and gas impinging on a flat surface.
Gas velocities varied from 13 to 52 cm/s and gas composition contained 9% CO 2 – 91% CO.
Decarburization rates were found to be consistent with those predicted for reactions limited
Freuhan and Martonik [Freuhan and Martonik (1974)] also showed that for the crucible
technique, the distance of the lance from the melt surface had a much larger influence on the
decarburization rate than the exit gas velocity. The authors reported that for melt carbon less
than 0.5 wt%, the decarburization rate was affected by resistance from the liquid phase
transport, which becomes the dominant limiting mechanism for melt carbon contents less
than 0.1 wt%. They further observed that a melt sulphur content of 0.3 wt% was found to
decrease the rate of decarburization by 10%. Hence they concluded that in the presence of
sulphur, slow interfacial chemical kinetics may influence the rate of decarburization due to its
surface activity. In an earlier study Freuhan and Martonik [Freuhan and Martonik (1971)]
investigated the decarburization of austenite using CO - CO2 gas mixtures. Strips of the iron
alloy were decarburized in the temperature range 850 – 1350 °C. Gas composition were
28
Chapter 2 Literature Review
chosen to avoid the formation of FeO. For gas velocities varying from 5.5 to 69 cm/s these
authors showed that the observed rates did not correspond with mechanisms limited by the
- Above 1250 °C, the decarburization rates were limited by carbon dioxide transport in
- Below 1000 °C rates were limited predominantly by slow chemical reaction at the
surface
- Between 1000 – 1250 °C there was a mixed control between the above mentioned
mechanisms.
In the regime limited by slow chemical reaction the rate was shown to be first order with
respect to the difference between the bulk and equilibrium partial pressures of carbon dioxide
and independent of the pCO/pCO2 ratio. They concluded that the rate was limited by the
dissociation of carbon monoxide on the surface. The rate constant obtained as a function of
10490
log kj 3.007 mol cm-2 s-1 atm-1 (2-27)
T
Where kj is in mol cm-2 s-1 atm-1 and T absolute temperature. These results were comparable
Two mechanisms for the adsorption of carbon dioxide on the reaction surface were
29
Chapter 2 Literature Review
The authors showed that if carbon and oxygen were strongly adsorbed on the surface, the
activated complex for carbon dioxide dissociation would be C2O2. If however, the fraction of
vacant sites at the surface is equal to 1 i.e. carbon adsorption at the surface is weak as
suggested by Grabke [Grabke (1964)], the second mechanism was indicated in their results
Nomura and Mori [Nomura and Mori (1973)] studied the kinetics of decarburization at 1600
°C. They used the crucible technique with gas velocities from 40 to 160 cm s -1 and found that
the decarburization rate was dependent on both the gas flow rate and the size of their lance. A
mixed control model was developed for gas phase mass transport and interfacial chemical
kinetics. Their results showed that for the conditions employed, the rate of decarburisation
was limited primarily by carbon dioxide transport in the gas phase, The chemical rate
constant values was estimated to be greater than 0.001 mol cm-2 s-1 atm -1
, which was
comparable to an extrapolation from a later work from Freuhan et.al. [Freuhan and Martonik
Lee and Rao [Lee and Rao (1982)] used the levitation technique, where liquid alloys were
decarburized in CO-CO2 gas mixtures with lance exit velocities up to 65 cm s -1. Most of the
The decarburization rates were found to be independent of the bulk carbon content of the
melts down to a critical carbon concentration of about 0.17 to 0.05 wt%. The authors showed
that the diffusivity of carbon in a levitated melt can be enhanced by an order of magnitude
30
Chapter 2 Literature Review
velocity, the presence of sulphur and the partial pressure of carbon dioxide in a manner
consistent with the earlier studies reviewed. By combining the chemical kinetics rate law with
the site blockage mechanism for surface active species and a relationship for the gas phase
flux of carbon dioxide, a mixed control model was formulated to describe their reults. The
rate constant for dissociative chemisorption of carbon dioxide on liquid iron was obtained as
Further studies [Shinme and Matsuo (1987)] based on Vacuum Stirring Decarburisation
(VSD) confirmed that the carbon dropped down to ~ 10 ppm, which is considered by some
authors to approach the equilibrium level. The apparent decarburization rate constant was
estimated, assuming a first-order equation (2-32) and the plot is shown on Fig. (2-11).
d [C ] A
- kc [C ] (2-32)
dt V
It was also found the apparent decarburization rate constant decreases with increasing initial
carbon content and in higher carbon content range a large amount of CO is formed and the
effect of evacuation on the decarburization rate is decreased. [Shinme and Matsuo (1987)]
Figure 2-13: Temperature dependence of the apparent rate constant.[Shinme and Matsuo
(1987)]
31
Chapter 2 Literature Review
al (2003)]The desiliconization reactions of Fe-Csat-Si alloy with CO and CO2 are represented
as (2-33, 2-34):
Si (mass %, in Fe- Csat alloy) + CO2 (g) = SiO2 (s) + C (s) (2-33)
The sample composition of Fe-C-Si contained about 10 wt% Si. After melting, Carbon
dioxide was blowed into the metal at fixed flow rates ranging 10-50 ml/min (s.t.p).
It was found that silicon would get oxidized in preference to carbon over 0.60 wt% Si under
the condition of aSiO 2 aC 1 at 1300 °C. Under the condition of preference desiliconizing,
namely, over 0.60 wt% Si, it was confirmed experimentally that only silicon was oxidized.
As the desiliconization reaction proceeded, the carbon content on the Fe-Si-C alloy increased
slightly in the experiments by CO2 injection. The overall rate constant of the desiliconization
was one order of magnitude larger than that of the decarburization. Experimental results
showing variations of silicon and carbon content with time are shown in Fig 2-14 and 2-15
respectively. The overall rate constants of simultaneous carbon and silicon oxidation under
the condition of Pco2 = 1 were determined to be 4.0x10-6 m/s and 5.0x10-6 m/s respectively. It
is inferred simultaneous oxidation of carbon and silicon causes some retarding effects on the
32
Chapter 2 Literature Review
These experimental studies were undertaken on melts with Si contents less than 10%. More
[Sakaguchi et al (1992)]. Carbon in silicon exceeding 50 ppmw was presented as SiC, and at
The removal of C from silicon and ferrosilicon during the ferrosilicon manufacturing process
had been investigated extensively by Klevan [Klevan (1997)]. The carbon is present in liquid
silicon and ferrosilicon as SiC and dissolved carbon. The oxidation process is described using
33
Chapter 2 Literature Review
With
Where
From (2-35) it is seen that decarburization is favoured by low silicon activity and a high
carbon activity in the metal, a high silica activity in the slag and a low CO partial pressure in
Carbon monoxide has to diffuse into bubbles and then get transported by these bubbles to the
surface of the metal bath. If the silica formed is a solid and dense layer around the bubbles,
the diffusion through this silica layer can be a slow process. At total carbon contents above
the levels given by (2-16) and (2-17) a solid –solid reaction between silicon carbide and silica
is possible:
aSi3 pCO
2
110939
ln K ln 2 50.67 (2-41)
aSiC aSiO 2 T
34
Chapter 2 Literature Review
With pure silicon the activity in (2-41) is all unity giving a partial pressure of CO below 0.10
atm. up to 1725 ˚C. The reduction of SiC by SiO 2 is very limited and kinetically, this reaction
Some experimental runs were conducted by Klevan [Klevan (1997)] blowing different
Argon/Air ratios at 1600 ˚C and a fixed flow rate (1.5 x 10-4 Nm3/s). Powersim® package
was used for simulating, using 2 different mass transfer coefficients (k c =1x10-4 m/s and
5x10-6 m/s). The results showed that there was a large resistance against removal of carbon
from liquid silicon when blowing air and Ar into the melt, since the simulation model gave a
mass transfer coefficient 5x10-6 m/s. Bubbles tended to break up and coalescence [ Anderson
et al (1987)] and bath circulation reduced the residence time [Klevan (1997)] The reaction
between oxygen in the gas bubbles and liquid silicon resulted in the formation of a silica
layer around the bubbles (Fig 2-15) which slowed down the decarburization.
The decarburization model in industrial case was also studied. There were two different flow
rates (15 and 30 Nm3/h) at 1600 ˚C. The initial carbon level was set at 150 ppmw, which was
equal to the solubility of carbon in FeSi 75. The results are presented in Fig 2-16 and resulted
in a very low decarburization rate. Reduction of carbon level from 150 ppmw to 100 ppmw
took 4 hours with an inert gas flow rate of 15 Nm3/h. When the flow rate was increased, the
rate of decarburization improved but the removal rate was still low.
35
Chapter 2 Literature Review
Figure. 2-16: Formation of a silica layer around a rising gas bubble when blowing oxygen
into liquid (ferro) silicon. The dense silica layer may result in a small mass transfer
36
Chapter 2 Literature Review
The results of these analyses combined with theoretical considerations have been summarized
where the oxygen activity is controlled by the equilibrium. It may not be of much
b) With a density difference between FeSi75 and SiC of 0.055 g/cm3 at 1450 ºC, the power
of flotation of SiC particles in liquid ferrosilicon is not sufficient to give any noticeable
separation effect.
c) SiC particles are effectively transferred to CaO and Al2O3 containing silicate slag being
formed when metal is exposed to air during tapping, pouring and teeming.
d) In the period of inert gas stirring, a transfer of SiC particles to the ladle walls removes
carbon, where a semi-molten slag layer forms at the interface between the molten metal
and the oxide lining. This indicates that it has a limited capacity to capture SiC particles
and explains why the observed carbon removal rate decreases with time during this
period.
e) Other mechanism that affect the macro and micro distribution of carbon in the cast are the
segregation of dissolved carbon along with other elements during solidification and the “
37
Chapter 2 Literature Review
Figure 2-18: Variations in carbon content and temperature in FeSi75 (l) during a sequence
of pouring (at time t > 0). Centric bottom Ar-stirring (0 < t < 50 min) and casting (t >50 min)
at Elkem Thamshavn. [Klevan (1997)]
2.6 Wettability
Wettability is the spontaneous response at the interface when a liquid is brought into contact
with the solid surface. In metallurgical processes, the interaction between various phases is
complex and its interpretation can sometimes be controversial. The wetting of solid surface
that has a higher melting point than liquid metal occurs in many physical phenomena and
technological process such as nucleation and growth, casting, soldering, welding and
The analysis of wettability in the systems formed by metal and binary compounds can be, to a
first approximation, carried out by considering the interactions between the liquid metal and
each type of components atoms of the solid phase. The actual strength of the interaction of
the metal and the compound will be weakened by the bonding between the components.
38
Chapter 2 Literature Review
Wetting refers to the macroscopic manifestation or molecular interaction between liquids and
solids in direct contact at the interface between them. Such manifestations include the
formation of a contact angle at the solid/liquid/gas interline, the spreading of a liquid over a
solid surface and the penetration of a liquid into a porous solid medium. Various wetting
Wettability can be expressed by the value of the contact angle θ and that has been recognized
as a critical parameter in bonding between two different materials. Young’s equation (2-42)
sv sl
cos (2-42)
lv
The contact angle is a directly observable parameter describing the compatibility of a solid
and liquid in equilibrium with a vapour. A liquid is said to wet a solid if θ < 90°.
If θ = 0°, the liquid completely spreads over the substrate of the solid. When θ > 90°, the
system is under a non-wetting condition. There are several established methods for the
measurement of contact angle. Some of the techniques that have been used are the tilting
plate method [Blake (1993)], the drop weight method [Bashforth and Adams (1883)], the
captive bubble method [Kemball (1946)], Neumann’s method [Rotenberg, Borucvk and
Neumann (1983)], the pendant drop method [Jimbo, Sharan and Cramb (1993)], the capillary
rise technique [Sharon and Cramb (1997)] and the Wilhemy plate technique [Butler and
Bloom (1966)].
Sessile droplet method is an established method for this study and is based on (2-42). The
technique uses a small liquid droplet placed in a flat, well- prepared and highly-polished
surface. The contact angle is obtained by visual means and therefore, surface energy can be
calculated. (Fig 2-19). The droplet must be as small as possible to render the influence of
39
Chapter 2 Literature Review
gravity on deforming the droplet negligible and the shaped obtained due to the interaction
liquid droplet / substrate is merely due to the balance of the interfacial force only.
Traditionally, X-ray transmission technique was used as a light source to investigate the
droplet/ substrate assembly on a film negative. The contact angle was measured using the
Bloom (1966)]. Recently, computer aided interfacial measurement systems have been
developed, combining the sessile-droplet method with X-ray radiography. The Laplace
The dynamic wetting can be explained as the change of the wetting of a solid / liquid system
over a period of time. Chemical reaction or mass transfer is generally the main reason for
those changes. Change of composition at the interface also might occur. Any factor that can
cause a small change in the interfacial energy could result in significant changes in the
wetting behaviour and therefore, the solid/liquid contact angle of the system. If there is no
significant change in the interfacial energy during the interaction, the system is characterized
[Kozatevich et al (1955)]
40
Chapter 2 Literature Review
Carbon dissolution from graphite into liquid iron occurs in this system. The chemical reaction
causes solute atoms to dissociate from solid graphite to form a micro region with high solute
Once the chemical reaction occurred, the mas transfer would also occur. The atom will
diffuse into liquid from the interface and form a liquid boundary layer as shown in Fig. 2-20:
C crystal [C]
Interface
In the system of liquid iron and graphite, the mass transfer of carbon on the interface can be
expressed as:
C 2C
KC D 2 (2-45)
t x
Where
41
Chapter 2 Literature Review
Mass transfer and interfacial reaction between graphite and molten iron can allow the wetting
condition (contact angle and interfacial tension) to be changed, mass transfer and interfacial
The wettability of pure iron on graphite has been well-investigated [Wu and Sahajwalla
(1994)][Sharan and Cramb (1997)]. Some experimental results on graphite substrates are
shown in table 2-2. These studies showed that pure iron showed good wetting at high
temperatures (1300 – 1500 °C) under different atmospheres, with contact angles ranging from
0 to 66°. However, it was observed that the wetting was affected when carbon content
increased in the melt. Contact angle increased from less than 90° up to around 140° [Sharan
Wu and Sahajwalla [Wu and Sahajwalla (2000)] studied the influence of the sulphur on the
wettability of Fe-C-S melts on graphite at 1550 °C. It was found the equilibrium contact
angle in a graphite/iron wetting system increased when sulphur increased in the melt and led
to a decrease in the rate of carbon dissolution in iron. The formation of an activated complex
of sulphur at the interface on the graphite dissolution could be responsible for the poor
wetting observed.
42
Chapter 2 Literature Review
(min)
[N et al]
62
43
Chapter 2 Literature Review
alumina by liquid iron has been investigated since the 1960’s. Table 2-3 shows a summary of
(min)
44
Chapter 2 Literature Review
ARMCO iron (ppm): 180 [C]; 100[Si]; 1600[Mn]; 60[P]; 250 [S]; 550[O]; 36[N]
St20 steel (%): 0.19 C, 0.29 Si, 0.65 Mn, 0.03 S, 0.016 P, 0.02 Ti, 0.025 Al, 0.0075 O
St35 steel (%): 0.35 C, 0.3 Si, 0.7 Mn, 0.025 S, 0.026 P, 0.09 Cr, 0.29 Ni, 0.22 Cu
St35L steel (%): 0.38C, 0.42 Si, 0.56 Mn, 0.03 S,0.04 P
St60 steel (%): 0.61C, 0.67 Mn, 0.27 Si, 0.016 P, 0.2 S, 0.12 Cu, 0.03 Cr, 0.04 Ni
Research on the wettability of alumina by liquid iron suggests that the contact angles were in
the range of 100 to 141º within the temperature interval of 1530 – 1600 ºC under different
Reported values of contact angle between Silicon and Silicon Carbide were compiled from
FeSi using two different compositions (33.33 and 66.67 at% Si). The contact angle measured
45
Chapter 2 Literature Review
[Klevan] 36 1480
[Klevan] 42 1430
[N&O] 0 1500
An overview of the cupola process and the main reactions of concern have been presented in
this chapter. When the metallic charges descend towards the burden bath, the iron and steel
scrap as well as the ferrosilicon melt interact with the coke bed; the hot gases (CO and CO2)
ascends from below, oxidizing the metal. Some of the phenomena such as carbon
dissolution, oxidation and dynamic wetting take place. These will be investigated in detail.
Phase diagrams for the Fe-Si, Si-C and Fe-Si-C systems have been reported in the literature.
Several studies had found more precision in some lines and points, although the Fe-rich
corner had been the main aim in many of those researches. The formation of different phases
such as SiC, FeSi and FeSi2 is satisfactorily explained by numerous previous researches and
46
Chapter 2 Literature Review
thermodynamic calculations although some recent work had brought more precision to
certain values.
The mechanism of carbon dissolution from graphite in pure iron had been well established by
i) Dissociation of carbon atoms from its crystal site in the graphite into the
carbon/melt interface.
ii) Mass transfer of carbon atoms through the adjacent boundary layer into the bulk
liquid iron.
mechanism. It had been found the dissolution rates are governed by the diffusion of carbon
from the metal-carbon interface to the bulk liquid through a boundary layer.
- For carbon contents higher than a critical value, the rate of decarburisation is
independent of the carbon concentration; this critical value is about 0.5 wt% carbon in
the melt. Below this critical concentration, the decarburisation rate decreased with the
carbon concentration.
- The decarburisation rate increased with increasing gas velocity, partial pressure of
- Several studies indicated that the CO2 dissociation was the rate limiting step for
Several studies regarding the carbon solubility in silicon have shown that the solubility of
carbon in the system Si / SiC at equilibrium is very low. The effect of the silicon contained in
ferrosilicon alloys on the carbon solubility had been also studied. It was found the carbon
solubility increased with the increase of silicon in the ferroalloy. However, below certain
47
Chapter 2 Literature Review
particularly when silicon is below 10%. For liquid iron with high carbon and silicon levels,
the oxidation rate was controlled by diffusion in the gas phase. Under certain conditions,
silicon was oxidized in preference of carbon. The overall rate constant of the desiliconization
When silicon contents were well above this value and in presence of Ar – air blowing showed
a large resistance of carbon removal due to the reaction between oxygen in the gas bubbles
and liquid silicon formed a silica layer around the bubbles, slowing down the decarburization.
There are several methods well-established for the study of wettability and contact angle
measurement. Description of the sessile-drop method has been provided and some recent
developments were explained. The wetting behaviour of iron on a graphite substrate and
Pure iron showed good wetting on graphite at high temperatures under different atmospheres
(vacuum, helium, hydrogen and argon). Previous studies proved the wettability of pure iron
on graphite was good and the contact angle ranged from 0 to 60°. However, when initial
carbon increases the wetting behaviour changed substantially, showing poor wettability (θ >
140 °).Research on the wettability of alumina by liquid iron suggested that the contact angles
were in the range of 100 to 141º under a range of different atmospheres (helium, hydrogen
and argon) as well as under vacuum. It was also found that the wetting in alumina improved
Previous work studying the wettability of silicon on SiC substrates under different
temperatures (1410 – 1500 °C), agreed the wetting was good ( θ = 0 - 42°). Ferrosilicon also
showed wetting and final contact angle values appeared to be independent of the % Si in the
ferroalloy.
48
Chapter 2 Literature Review
However, despite the important role of the carbon pickup in the scrap-melting process, the
reaction kinetics of the carbon dissolution in silicon-rich alloys is not yet well understood.
Although there is a large body of work studying the interaction of silicon and ferrosilicon
alloys in SiC, those researches had been focused on bonding properties. The dynamic wetting
from the metallurgical point of view had not been studied in depth, in spite the significance of
the interfacial interaction in the reaction kinetics. The simultaneous decarburization and
desiliconization has been studied but the information found is referred to low silicon and
carbon content in the metal, which is not the situation found in the cupola process, where
carbon and silicon contents are, so far, below the limits required during the steelmaking.
Present study reports the reaction kinetics of the carbon dissolution on 25, 75 and 98 wt% Si
alloys, the dynamic wetting of those ferroalloys on graphite and SiC and the interaction of the
49
CHAPTER 3
EXPERIMENTAL DETAILS
Chapter 3 Experimental Details
silicon ferroalloys during the cupola melting process, as well as interfacial phenomena during
the interactions between carbon and ferrosilicon alloys. The influence of the gas phase on the
metal during the melting process in the cupola has been investigated. Carbon dissolution
furnace. Carbon transfer from the substrates to the metal was measured by the LECO CS 244
Carbon Sulphur Analyser. Dynamic wetting investigations were carried out by measuring the
contact angle between the molten metal and the synthetic and natural graphite as well as 85%
SiC substrates. Interfacial studies were conducted by X-Ray Diffraction (XRD), while the
Electron Probe Micro Analyser was used for interfacial analysis and chemical
characterisation of the metallic phase. Gas phase interactions of the molten alloys were
Metallurgical-grade coke added as part of the charge plays two important roles in the cupola
process. The major exothermic reaction takes place between carbon contained in the coke and
the oxygen in the blast. The combustion reactions provide the required amount of heat to melt
the scrap metal and to keep the liquid bath at the desired temperatures. Carbon from coke also
dissolves into the liquid metal, raising the carbon content up to the required levels.
Silicon is another important alloying element present in cast irons, and plays an important
role in controlling iron structure and properties of cast irons. It is added predominably as
ferrosilicon lumps with up to 75 wt% of silicon. During the cupola process, alternative layers
of coke, iron and steel scrap, fluxes and ferrosilicon are added continuously, interacting each
51
Chapter 3 Experimental Details
This chapter provided details material selection and process parameters, experimental
apparatus and instruments for the investigation of the carbon dissolution phenomena during
the carbonaceous material – ferrosilicon alloy interaction, the interfacial reaction and the
and 50 wt% of silicon are used widely in steelmaking and cast iron processes, therefore their
Silicon 98.5% and FeSi 25 were chosen as reference materials in this study, covering both,
high and low silicon limits. Lower silicon content up to 3.5% wt Si which are of great
importance for steelmakers, have been extensively reported in the literature and are therefore
Raw materials required to prepare the high-purity ferrosilicon alloys were electrolytically -
grade pure iron chips (99.98%) (CAS Number 7439-89-6 ) and high-purity silicon chunks
(98.5%) (CAS Number 7440-21-3), both were supplied by Sigma-Aldrich. The materials
were carefully weighed and mixed thoroughly to achieve the desired compositions. The
amount of metal sample used in the carbon dissolution experiments ranged between 0.2-0.4
grams. Samples were crushed in finer pieces and compacted into the crucibles to achieve
enhance homogenization.
Mixtures were melted using a lab-scale arc smelter. Before melting, the entire system was
checked for leaks in order to prevent any air/oxygen ingress. The system was under vacuum
after purging inert gas several times to assure the removal of any remaining oxidizing gas.
The inert gas stream (10% Hydrogen, 90% Argon) was supplied continuously while the
smelting was on. The mixture was sparked with the electric-arc for 15-20 seconds. The
resultant product was a round-shape tablet. After this period of time, the process was stopped
52
Chapter 3 Experimental Details
to avoid excessive temperatures (greater than 1650 °C) that could damage the equipment. The
tablet was turned over and after few minutes, the above procedure was repeated few more
times. Once the tablet cooled down, it was broken in smaller pieces and chemical analyses
were carried out by Induced Coupled Plasma mass spectroscopy (ICP). Results are shown on
Commercial ferrosilicon alloys contain high impurity contents such as aluminium and
calcium; make them unsuitable for fundamental studies. Aluminium affects the carbon
solubility in the molten ferrosilicon [Ottem (1993)]. On the other hand, ferroalloy containing
50 wt% of silicon was extremely brittle, making its separation from the graphite crucibles
very difficult and therefore introducing unacceptable error levels when samples were
Table 3-1 Typical composition of few commercially available ferrosilicon alloys [Cupola
Handbook (1984)]
Si Al Ca C Fe
53
Chapter 3 Experimental Details
Ferroalloy
composition Fe (wt%) Si (wt%) Al (wt %) Other elements (wt%)
26.7 72 <0.1 <0.1
24.3 73.6 <0.1 <0.1
FeSi 75 24.5 73.4 <0.1 <0.1
26 73.5 <0.1 <0.1
28 71.5 <0.1 <0.1
Synthetic graphite was used as the main carbon source to understand the effect of ash-free
carbon on carbon transfer and to minimize the impact of other components such as the
volatile matter and the ash in such reaction. Synthetic graphite was also used for the dynamic
wetting investigation. The absence of impurities and negligible ash content minimized the
potential interference on the wetting behavior. It is well established that even small amounts
of components such as sulphur, can affect significantly the wetting behavior between the
carbonaceous material and the metal. [Wu et al (1998)] An analysis of the synthetic
graphite is provided on Table 3-3 and shows 0.2% of ash content. Synthetic graphite
crucibles (Fig 3-1 a, b, c) were used for carbon dissolution experiments. Their structure was
characterized by XRD resulting on a 2H (Clifftonite) structure (Fig 3-1d). There were also
synthetic graphite plates made out the same material, which were used for wettability studies.
54
Chapter 3 Experimental Details
Hydrogen NM
Nitrogen NM
IM 0.2
Carbon 99.1
(%)
SiO2 39
Fe2O3 22.3
Al2O3 13
TiO2 1.2
P2O5 0.28
Mn3O4 1.3
CaO 6.7
Na2O 3.0
MgO 4.8
K2O 3.6
SO3 2.4
V2O5 0.06
Cr2O3 0.60
55
Chapter 3 Experimental Details
10 mm
15 mm
2000
1800
1600
1400
1200
Intensity
1000
800
600
400
200
0
20 25 30 35 40 45 50 55 60
2- Theta
56
Chapter 3 Experimental Details
Figure 3-1d: XRD scan for synthetic graphite crucibles. Peaks corresponded with 2H-
graphite (Clifftonite)
The dynamic wetting behavior also was investigated between a natural graphite substrate and
molten ferrosilicon alloys. It is well established that natural graphite shows good wetting
behavior with molten steel [Timcal (2006)]. Natural graphite have greater content of ash
impurities compared to synthetic graphite, but this material was especially chosen due to their
relevance for industrial conditions, The pulverized natural graphite was supplied by Asbury
Graphite Mills, NJ, USA and the particle size was < 63 μm. Characterization of natural
interfacial product is thermodynamically feasible. This was later confirmed during the
preliminary interfacial studies after the carburization experiments were completed. The
appearance of the SiC layer at the interface suggested it could play key role during both,
carbon dissolution reaction and wettability. In view of this, Silicon Carbide was also used as
a substrate for both investigations. The SiC substrates were obtained from supplied SiC tiles
57
Chapter 3 Experimental Details
and were cut using a diamond saw. Selected dimension was (24 x 24 x 2 mm). The
Hydrogen (%) NM
SiO2 41.4
Fe2O3 16.5
Al2O3 15.2
TiO2 0.56
P2O5 0.14
Mn3O4 0.17
CaO 8.5
Na2O 1.2
MgO 9.4
K2O 2.3
SO3 2.98
V2O5 0.05
Cr2O3 0.06
58
Chapter 3 Experimental Details
3.1.5 Alumina
The crucibles for the gas phase – metal investigation were made out of 99.9% Al2O3. This
material is considered ideal for the production of crucibles and other refractory parts,
displaying excellent corrosion resistance and mechanical wear resistance and strength, as well
as good thermal resistance. The crucibles were made by the strip casting method. A solution
containing 99.9% Al2O3 was mixed thoroughly for about 2 hours and further cast in moulds.
This step was repeated twice, allowing about 5 minutes en between to settle the material. The
leftovers were removed and the crucibles were left for drying during 24 hours before they
were sintered at 1200 °C during 2 hours. The crucible dimensions are shown on Fig 3-3 a and
b.
10 mm
12 mm
59
Chapter 3 Experimental Details
several experiments were undertaken under a mixed gases containing CO2 and CO.
Relative properties of gases are shown in Table 3-5. Flow rates were set at 1 liter/minute for
gas 1 and 0.5, 1 and 2 liters/minute for gas 2. The gaseous mixture 2 was set up according to
previous studies regarding the gas phase profile in the cupola furnace [Cupola Handbook
(1984)] for regions close to the tuyeres (oxidation zone). Argon gas was purged into the
reaction chamber until samples were melted, and then, the reactive gas switched on. After
keeping the samples under such atmosphere for a fixed period, the reactive gas was switched
off and argon was brought back to the reactor chamber and then, the sample was quenched.
Gas 1 100 - -
Gas 2 20 2 78
The experimental work was carried out employing different pieces of equipment and
analytical instruments. Among the most important are the horizontal tube furnace, Infrared
(IR) gas analyzer, X-Ray Diffractometer and Electro Probe Micro Analyzer (EPMA).
The horizontal furnace used on the current project has been described thoroughly by several
authors [Zhao (2003][ Wu and Sahajwalla (2000)][ Mehta and Sahajwalla (2000)] (Fig 3-4) It
includes 1 meter-long and 50 mm inner-diameter high alumina reaction tube with two Super
60
Chapter 3 Experimental Details
Kanthal resistance-heating elements. The furnace is built from a double skin stainless steel
with welded tubular chassis. For heat dissipation, a cooling fan was set on the top. There are
two separate temperature indicators, each one with Pt-30%/Rh/Pt-6% Rh thermocouples. One
of them is placed inside of the reaction chamber, near to the sample, while the others
The temperature profile along the length of the furnace tube was also produced to determine
the location of the hot zone. Under an established temperature, a thermocouple sample was
temperature profile. (Fig 3-5) The general procedure for all planned experiments was
identical. The assembly of sample and substrate was placed on the cold zone for about 10
minutes. This pause was needed to allow certain temperature homogeneity, since sudden
temperature variation might lead to the risk of thermal cracks in the alumina tube.
Thermocouple
CCD Camera
Time/Date
generator
Off gas
Alumina tube TV
Hot zone VCR
61
Chapter 3 Experimental Details
The other purpose was to flush away any remaining gas from the outside atmosphere, since
the experimental conditions need to take place under an inert atmosphere. After this period of
time, the sample was pushed via a sliding mechanism into the hot zone and kept there for the
desired time. Once the run was over, the sample was quenched into the cold zone and kept for
Due to the natural tendency of silicon to oxidize at high temperatures, a high-purity Argon
gas stream (> 99%) was used during the carburization runs. Gas flow was controlled by an
electronic flow controller. For removing away any remaining moisture and oxygen, an
additional gas cleaning system was used based on previous successfully experimental work
1600
1550
1500
1450
Temperature (C)
1400
1350
1300
1250
1200
1150
0 5 10 15 20 25
Distance ( cm)
Figure 3-5: Temperature profiles. Values decrease from the hot zone to the cold zone.
62
Chapter 3 Experimental Details
A high-resolution CCD (charged coupled device) camera was fitted with an IRIS lens. The
output was channeled to a VCR-TV monitor. A time and date generator was used in the
system to display the date and duration of the reaction. The recorded images were captured
by using a frame grabber and copied in a computer. Due to rapid changes in the dynamic
wetting, selected images were taken every 10 seconds. The wettability of the liquid
appropriate software based on Laplace equation. The software performed a curve fitting
A BROOKS Instruments mass-flow controller, model BBC 1A11A was used to control gas
flow rates. Two flow controller sensors, one for argon gas and the other for the oxidizing gas
mixture, were attached to the corresponding ports. Changes in oxygen partial pressure were
63
Chapter 3 Experimental Details
tracked down by an Infra Red (IR) ABB 2020. The off-gas composition (CO2/CO) was
recorded into a coupled personal computer. The data were recorded as volume (%) and
(ppm). The changes in off-gas composition usually were observed during the first 15 minutes
and generally remained steady after this period. The upper detection limits of the IR were 20
% (Volume) CO2 and 5 % CO, therefore, no changes were detectable during the oxidation
experiments, since the inlet gas composition was above those limits.
The wettability was characterized by measuring the contact angle at the ferroalloy/substrate
interface. The experimental approach involved used the sessile- drop method as function of
the type of substrate, ferroalloy composition and time. The interfacial reaction was also
interface. The study correlates the dynamic wetting and the interfacial reaction. The
appropriate means for further contact angle measurements. Figure 3-11 shows an example of
a screen shot and calculated parameters during the dynamic wetting experiments.
Figure 3-7: Example of contact angle measurement during the dynamic wetting
investigations.
64
Chapter 3 Experimental Details
A flow diagram of the algorithm is detailed in previous work [Wu et al (1998)] as shown on
Figure 3-8. For contact angle values below 30˚, the accuracy of the above-mentioned
Special software allowed defining the edges of the droplet, by selecting specified and varying
number of points. The points were conveniently arranged by fitting a curve to the image with
various degrees of polynomial equations (degrees 1 to 5) and measuring the angle between
the tangent to the curve and the substrate. The contact angle could be obtained separately for
The LECO CS 244 was used to determine carbon levels during carbon dissolution
experiments. The working principle for the determination of the carbon and sulphur content
in the metal is by melting the sample in an induction furnace in the presence of excess
oxygen. The combustion reaction takes place and all the carbon and sulphur is oxidized and
A Siemens D 5000 X-ray Diffractometer was used for the study of interface products at
interface. Cooper Kα radiation (30 KV, 30 mA) was used as an X-ray source. Samples were
placed on modeling compound and leveled, in order to guarantee an even exposed surface.
Samples were scanned in a step-scan mode (0.02° /step) at 1°/minute. Scanned angles started
from 25 up to 100°.
65
Chapter 3 Experimental Details
throughout selected areas was carried using an Electron Probe Micro Analyzer (EPMA)
Cameca SX50. This equipment employs four wavelength dispersive spectrometers and one
energy dispersive X-ray analyser for the detection and non-destructive analysis of almost all
elements from Boron (4) down in the periodic table. X-ray elemental line scans were carried
out across of constituents of interest. Specimens were also imaged using either secondary or
backscattered electrons.
These investigations were carried out to identify the distribution of different components, not
only in the bulk of the metal sample but particularly, identifying the formation of interfacial
products. Scanning of selected points and areas, as well as element distribution mapping was
employed. Figure 3-9 shows an example of the silicon distribution after the interaction of
66
Chapter 3 Experimental Details
Select image
area
Binary Image
Edge detection
y
Inclination ?
n Correction
Setting top of
substrate
Blanking extraneous
information
Parameters
selection
Profile points
initialization
Curve fitting
calculation
Data ,image
storage
End
Figure 3-8: The working flow sheet of “interface software” for analysis of the contact angle
67
Chapter 3 Experimental Details
Metal droplet
SG substrate
Figure 3- 9a: Silicon mapping after FeSi 25 – synthetic graphite interaction at 1550°
Metal droplet
SG substrate
Figure 3- 9b: Optical image of after FeSi 25 – synthetic graphite interaction at 1550° C
68
Chapter 3 Experimental Details
The accuracy of the results depended, in a large extent, of the removal of impurities (graphite
particles) from the samples. This issue was critical, since the results obtained at early stages
could set distorted greatly by the presence of graphite particles adhering to the sample
surface. Low-silicon samples were easily taken off the synthetic graphite crucibles, since no
strong bond with the substrate was found. However, the adherence for the high-silicon
samples was notably higher; therefore the separation from the substrate was carried very
carefully. Graphite leftovers were removed by using sand paper (180 μm) placed in the
rotating disk. After carefully visual inspection, some samples were cleaned by chemical
attack. They were placed in a solution containing about 10 ml of 30% peroxide (H2O2)
The samples used for carbon dissolution on SiC substrates were cut in the boundary metal /
substrate, using a very fine diamond saw at low speed. They were cleaned and sent for carbon
analysis. Once the samples were cleaned, Carbon analyses were undertaken on the Carbon-
The pulverised natural graphite and the coke samples (particle size < 63 μm) were compacted
by using a steel die (Fig 3-10) without any binder. The amount of sample placed in the die
was about 4 grams. The powder was compacted in a hydraulic press (Fig 3-11) under and the
applied pressure was gradually increased by 1 ton steps every 2 minutes until reaching about
69
Chapter 3 Experimental Details
The formation of the interfacial products was investigated using XRD. Figure 3-11 shows a
schematic of the samples used for XRD analysis. The samples were removed carefully from
the substrates and any remaining graphite was removed by grit paper (1200 μm) placed in the
rotating polisher. The samples were molded using a thermosetting resin at 120 ˚C and then,
ultrasonically cleaned.
Metal droplet
Substrate
Figure 3-12: Schematic of the metal droplet – substrate sample used for interfacial
investigations
70
Chapter 3 Experimental Details
Interfacial studies were also carried out using EPMA and samples were similar to the ones
used for XRD (Figure 3-12). Samples were mounted in epoxy resin and had a flat and well-
polished surface, finished up to 0.1 micrometers. The specimen surfaces were flat with
perpendicular sides. These were baked and later cooper-coated to facilitate microscopic
examination.
71
CHAPTER 4
This chapter presents measurements of the dynamic wetting between silicon and ferrosilicon
alloys and synthetic graphite, natural graphite and silicon carbide (SiC) at 1550 ºC.
Investigation of the interfacial product and its role in the dynamic wetting phenomena is also
discussed.
4.3 Study of the dynamic wetting for silicon and ferrosilicon alloys on synthetic graphite
The influence of the ferroalloy composition on the wetting behavior was investigated for
ferro (silicon) alloys ranging from 24.7 wt% up to 98.5 wt% on synthetic graphite substrate
under argon atmosphere at 1550 °C. The wetting behavior of ferroalloys containing 24.7, 74
and 98.5% Si on synthetic graphite substrates is shown in Fig. 4-1 to Fig. 4-3. The samples
displayed generally good wetting behavior (θ < 90º). Full wetting was observed for high-
silicon ferroalloys within the first 90 seconds (Fig 4-4, 4-5). However, the final contact angle
value appeared higher for the low-silicon ferroalloy (24.7 wt% Si) and remained steady
a) 1 second b) 13 seconds
72
Chapter 4 Dynamic Wetting
c) 23 seconds d) 60 seconds
Figure 4-1: Still image of liquid silicon (Si 98.5%) droplet on synthetic graphite substrate a)
1 second after melting, b) 13 seconds, c) 23 seconds, d) 60 seconds
a) 1second b) 30 seconds
c) 60 seconds d) 80 seconds
Figure 4-2: Still image of liquid FeSi 74 droplet on synthetic graphite substrate
a) 1 second after melting b) 30 seconds, c) 60 seconds, d) 80 seconds
73
Chapter 4 Dynamic Wetting
a) 1second b) 30 seconds
Figure 4-3: Still image of liquid FeSi 24.7 droplet on synthetic graphite substrate a) 1
second after melting, b) 30 seconds, c) 50 seconds, d) 300 seconds, e) 570 seconds, f) 1170
seconds
74
Chapter 4 Dynamic Wetting
120
100
Contact Angle (degrees)
80
60
40
20
0
0 20 40 60 80 100
Time (seconds)
Figure 4-4: Dynamic Wetting of Si 98.5 wt% on synthetic graphite.
160
140
Contact Angle (degrees)
120
100
80
60
40
20
0
0 20 40 60 80 100
Time (seconds)
75
Chapter 4 Dynamic Wetting
140
120
Contact Angle (degrees)
100
80
60
40
20
0
0 200 400 600 800 1000 1200
Time (seconds)
The occurrence of some interfacial reaction during the wetting on graphite, and therefore, the
At 1550 °C the Gibbs free energy for SiC = -5.58 x 104 J [Barin (1995)], so the formation of
this product is thermodynamically feasible at such a temperature. Reported results from Nogi
and Ogino [Nogi and Ogino (1988)] and Nikolopoulos et al [Nikolopoulos et al (1992)]
showed good wetting between silicon and SiC, so this lead to further investigate the product
76
Chapter 4 Dynamic Wetting
The interface of ferrosilicon alloys/graphite was scanned by XRD in order to evaluate the
formation of interfacial products. Figs. 4.7, 4.8 and 4.9 show the XRD scanning for Si 98.5%,
FeSi 74% and FeSi 24.7% interacting with synthetic graphite at 1550°C. The results showed
that SiC appears 30 seconds after melting for Si 98.5%. The formation of SiC at the interface
of FeSi 74%/graphite was observed 60 seconds after melting. For FeSi 24.7%, the SiC was
detected after 30 minutes of the interfacial reaction. Back-scattered images using the EPMA
(400X) also showed the formation of SiC, although it was observed the interfacial layers
were irregular and presented variation on the thickness. (Figs. 4.10, 4.11 and 4.12)
Silicon Carbide
Silicon
700
600
500
t=30 seconds
Intensity
400
300
200
0
20 30 40 50 60 70
2-Theta
Figure 4-7: XRD spectra. Interface of Si 98.5% / synthetic graphite after 0 and 30 seconds
at 1550 °C
77
Chapter 4 Dynamic Wetting
800
700
600
t=60 seconds
500
Intensity
400
300
200
100
t=1 second
0
28 33 38 43 48 53 58 63 68 73
2-Theta
Figure 4-8: XRD spectra. Interface of FeSi 74 % / synthetic graphite after 1 second and 60
78
Chapter 4 Dynamic Wetting
FeSi2
SiC
500
450
400
350
t=1800 seconds
300
Intensity
250
200
150
50
0
25 30 35 40 45 50 55 60 65 70 75
2-The ta
Figure 4-9: XRD spectra. Interface of FeSi 24.7 % / synthetic graphite after 1 second and
79
Chapter 4 Dynamic Wetting
Figure 4-10: Back-scattered electron EPMA image at the interface Si98.5/synthetic graphite
(400X).
Figure 4-11: Back-scattered electron EPMA image at the interface FeSi 74/ synthetic
graphite (400X)
80
Chapter 4 Dynamic Wetting
Figure 4-12: Back-scattered electron EPMA image at the interface FeSi 24.7/ synthetic
graphite (400X)
Experimental runs investigating on SiC substrates on the dynamic wetting were carried out at
1550 °C. The studies were undertaken using the same ferroalloys described on section 4.1
and using SiC substrates. Still images are shown in Fig. 4-13 to Fig. 4-15.Comparative
wetting behaviour of the ferrosilicon samples on synthetic and SiC are presented in Fig 4-16
to 4-18.
81
Chapter 4 Dynamic Wetting
1 second) 5 seconds)
26 seconds) 50 seconds)
Fig 4-13 Still image of liquid silicon (Si 98.5%) droplet on SiC substrate
82
Chapter 4 Dynamic Wetting
1 second) 10 seconds)
50 seconds) 70 seconds)
Figure 4-14: Still image of liquid ferrosilicon (75%) droplet on SiC substrate
83
Chapter 4 Dynamic Wetting
1 second) 10 seconds)
Figure 4-15: Still image of liquid ferrosilicon (25%) droplet on SiC substrate
84
Chapter 4 Dynamic Wetting
120
80 Si 98.5% / SiC
60
40
20
0
0 10 20 30 40 50 60 70 80 90
Time (seconds)
Figure 4-16: Dynamic wetting of Si 98.5 wt% for synthetic graphite and SiC substrates.
160
100
80
60
40
20
0
0 20 40 60 80 100
Time (seconds)
Figure 4-17: Dynamic wetting of FeSi 74 wt% for synthetic graphite and SiC.
85
Chapter 4 Dynamic Wetting
140
100 FeSi25/SiC
80
60
40
20
0
0 1000 2000 3000 4000
Time (seconds)
Figure 4-18: Dynamic wetting of FeSi 24.7 wt% for synthetic graphite and SiC substrates.
The wetting of Si 98.5 wt% displayed similar trend for both, synthetic and natural graphite
substrates. The initial contact angle for synthetic graphite was 105º, while this value was
52.6º for SiC. After 80 seconds, the contact angle for synthetic graphite decreased down to 0º.
Similar trend was also observed for SiC, reaching full wetting after 80 seconds.
The wettability study for FeSi 74 wt% showed similar trend to the one observed for Si 98.5
wt%. The initial contact angle value on synthetic graphite was 140º. This value was slightly
lower for SiC (134 º). For both, synthetic graphite and SiC substrates, full wetting was
The dynamic wetting for FeSi 24.7 wt% displayed different pattern. The initial contact angle
for synthetic graphite (112º) decreased down to 99º after 60 seconds. After this time, the
wetting showed slight improvement up to 600 seconds, when showed a steady trend around
86
Chapter 4 Dynamic Wetting
the 80º. Instead, the wetting on SiC showed an initial contact angle of 92º but this decreased
The ferroalloys tested showed good wetting on SiC. However, the dynamic wetting behaved
differently for high and low silicon alloys. While the contact angle decreased down to 12° (Si
98.5%) in 70 seconds and 31° (FeSi 74%) in 80 seconds, the decrease for FeSi 24.7% was
much slower, reaching 38° after 300 seconds. A similar trend was also observed when
dynamic wetting was investigated on graphite substrates. It was found that the high silicon
alloys reached full wetting (θ = 0°) within 90 seconds. However, the dynamic wetting
changed at a slower rate for FeSi 24.7%, since the contact angle decreased after 300 seconds
The XRD spectra at the ferrosilicon – graphite interface provided evidence regarding the
formation of SiC during their interaction, explaining the reported differences on dynamic
wetting. It was clearly shown that the appearance of strong peaks of SiC occurred after 30
and 60 seconds for Si 98.5% and FeSi 74%, while they appeared at 1800 seconds for FeSi
24.7%. This suggests that the dynamic wetting is strongly related to the rate at which the
interfacial reaction occurs. In addition, EPMA back-scattered electron images confirmed the
appearance of the SiC as interfacial product, although that compound was distributed
The dynamic wetting for high-silicon alloys on graphite and SiC showed similar behaviour.
Both cases exhibited a sharp decrease in the contact angle, reaching full wetting at 90 seconds
on graphite, and decreasing to 12° (Si 98.5%) and 31° (FeSi 74%) before 90 seconds. The
wetting for FeSi 24.7%, however, showed a different trend. The contact angle decreased
slowly on both substrates, remaining steady at around 70° on graphite after 400 seconds and
38° on SiC after 180 seconds. The results obtained on SiC substrates confirmed that the
87
Chapter 4 Dynamic Wetting
dynamic wetting behaviours for each ferroalloy were consistent with the ones on graphite and
provide additional evidence in the role played for SiC on this phenomenon.
The experimental results indicated the strong relationship between the amount of silicon
contained in the ferroalloys and the interfacial reaction rate. The early appearance of SiC as
alloys) is seems to be related with the changes observed in the dynamic wetting. The
differences observed during the formation of SiC at the interface ferrosilicon /graphite
(occurring rapidly in Si 98.5 and FeSi 74% and slower for FeSi 24. %) might explain the
differences in dynamic wetting observed in both, high and low silicon ferroalloys. The results
obtained on SiC substrates confirmed that the dynamic wetting for each ferroalloy were
consistent with the ones on graphite and support the role played by SiC on this phenomenon,
4.5 Summary.
The interfacial phenomena during the interaction of ferrosilicon with silicon – graphite and
SiC were studied. This research focused on dynamic wetting and the formation of interfacial
products.
1) The ferrosilicon alloys showed good wetting on synthetic graphite and SiC. However,
the contact angle decreased much more quickly for high-silicon ferroalloys compared
to low-silicon ferroalloy.
2) The good wetting behaviour is due to the formation of SiC as an interfacial product.
3) The dynamic wetting seems to be strongly dependent on the rate of formation of SiC
88
Chapter 4 Dynamic Wetting
4) The dynamic wetting for high-silicon alloys on graphite and SiC showed similar
behaviour. Both cases exhibited a sharp decrease in the contact angle, reaching full
showed a different trend with the contact angle decreasing slowly on both substrates.
89
CHAPTER 5
DISCUSSION
Chapter 5 Carbon Dissolution
The carbon dissolution for silicon and ferrosilicon alloys from synthetic graphite substrate is
presented in this chapter. The studies were carried out on ferrosilicon alloys containing 24.7,
74 and 98.5 wt% Si at 1550 °C. Investigation of the interfacial product at the interface was
carried out, finding that SiC was formed. The role of the interfacial layer was further
kinetics and the proposed mechanism for this phenomenon are discussed.
Initially carburization investigations were undertaken with pure iron using the existing
experimental set up. These results showed that the carbon saturation limit in pure iron was
5.57 wt% C, which is in good agreement with published data [Zhao (2003)]. (Figure 5-1)
Carbon pickup from synthetic graphite as function of time for ferrosilicon alloys at 1550° C
has been investigated and is shown in figures 5-2 to 5-4. Carbon dissolution from synthetic
graphite into ferrosilicon alloys was investigated as a function of time. Detailed experimental
results are presented in Figures 5-2 to 5-4. Enlarged regions of high change are shown in
figures 5-2a to 5-4a. It was observed that the carbon content increases within the initial 10
minutes but these levels remain constant after this increase. The carbon pickup trend showed
A different behaviour was found for FeSi 24.7%, where a sharp increase in carbon content
91
Chapter 5 Carbon Dissolution
4
Wt% C
2 Current work
Zhao (2003)
1
0
0 20 40
Time (minutes)
Figure 5-1: Carbon pickup from graphite into pure iron at 1550 °C.
0.1600 0.1
0.1400
0.08
0.1200
0.1000 0.06
W% C
Wt% C
0.0800
0.04
0.0600
0.02
0.0400
0.0200 0
0.0000 0 0.5 1 1.5 2 2.5 3
0 50 100 150 200 250 300 350 Time (minutes)
Time (minutes)
Figure 5-2: Carbon pickup from graphite Figure 5-2a: Carbon pickup from graphite
into Si 98.5% at 1550 °C. into Si 98.5% at 1550 °C during the first
three minutes.
92
Chapter 5 Carbon Dissolution
0.16 0.1
0.14
0.08
0.12
0.1 0.06
Wt% C
Wt% C
0.08
0.04
0.06
0.04 0.02
0.02
0 0
0 50 100 150 200 250 300 350 0 0.5 1 1.5 2 2.5 3
Time (minutes) Time (minutes)
Figure 5-3: Carbon pickup from graphite into Figure 5-3a: Carbon pickup from graphite
FeSi 74% at 1550 °C. into FeSi 74% at 1550 °C during the
first three minutes
0.16
0.1
0.14
0.12 0.08
0.1 0.06
Wt% C
Wt%C
0.08
0.04
0.06
0.04 0.02
0.02 0
0 0 0.5 1 1.5 2 2.5 3
0 50 100 150 200 250 300 350
Time (minutes) Time (minutes)
Figure 5-4: Carbon pickup from graphite into Figure 5-4a: Carbon pickup from
FeSi 24.7 at 1550 °C. graphite into FeSi 24.7% at 1550 °C
during the first three minutes.
93
Chapter 5 Carbon Dissolution
It is well established that there is a direct relationship between silicon and carbon content in
the ferroalloy [Ottem (1993)], showing a trend for silicon content greater than 50wt%.
However, below this limit, carbon dissolved in the metal holds an inverse dependence with
the silicon content in the ferroalloy. The rapid carbon pickup during the first 3 minutes
suggested a similar kinetic mechanism observed for carbon dissolution in iron. In view of the
similarities, a first order kinetic equation was applied for the analysis of the rate constant.
dC
k ( Cs Ct ) …………………. (5.1)
dt
dC
(Cs Ct )
kdt ……………….. (5.2)
(Cs Ct )
ln kt …………………… (5.3)
(Cs Co)
Where,
Cs is the melt carbon saturation;
Ct is the instantaneous melt carbon content; and
Co is the initial carbon content.
(Cs Ct )
From plotting ln
(Cs Co) vs. time t (seconds), the constant rate k can be deduced
graphically. Figure 5-5 to 5-7 shows these plots for Si 98.5%, FeSi 74 and FeSi 24.7 runs at
Time(seconds)
-0.1 y = -0.0038x
R2 = 0.9779
-0.2
ln{(Cs-Ct/Cs-Co)}
-0.3
-0.4
-0.5
-0.6
-0.7
-0.8
(Cs Ct )
Figure 5-5: Plot of ln vs. time (seconds) for carbon dissolution runs of Si 98.5
(Cs Co)
at 1550 °C.
Time (seconds)
-0.1
-0.2
ln{(Cs-Ct/Cs-Co)}
-0.3
-0.4
-0.5
-0.6
y = -0.003x
-0.7 R2 = 0.9821
-0.8
(Cs Ct )
Figure 5-6: Plot of ln vs. time (seconds) for carbon dissolution runs of
(Cs Co)
FeSi 74 at 1550 °C.
95
Chapter 5 Carbon Dissolution
Time(seconds)
-0.1
ln{(Cs-Ct/Cs-Co)} -0.2
-0.3
-0.4
-0.5
y = -0.0039x
-0.6 R2 = 0.9812
-0.7
-0.8
(Cs Ct )
Figure 5-7: Plot of ln vs. time (seconds) for carbon dissolution runs of
(Cs Co)
FeSi 24.7 at 1550 °C.
FeSi 24.7 achieved the higher carbon saturation (Cs) limit (0.149% C) compared with FeSi 74
(0.105% C) and Si 98.5 (0.116%C). Reported data from the literature [Ottem (1993)],
[Klevan (1997)] also showed lower Cs for FeSi 75 compared to pure silicon. Rate constants
obtained for FeSi 24.7, FeSi 74 and Si 98.5 were 3.9 x 10-3, 3 x 10-3 and 3.8 x 10-3
respectively, showing a direct correlation with Cs values. The initial carbon content for all the
ferrosilicon samples is very low (approximately 0.02 – 0.03 wt% C), but during the initial
three minutes, carbon contents increased rapidly up to certain value and remained steady after
this time. This indicated that at the early stages, the transfer of carbon from the graphite
substrate to the metal is favoured by the carbon gradient (from high concentration of carbon
in the graphite substrate to low carbon content in the ferrosilicon alloy) until carbon content
in the metal approached saturation levels. This does not exclude that other process such as
carbon diffusion from the bulk of the graphite plate to the surface and the interfacial reaction
at the graphite-ferrosilicon interface also occurred, but the experimental results indicated that
96
Chapter 5 Carbon Dissolution
the mass transfer mechanism plays a key role during the initial stages (3 minutes) of the
interfacial reaction.
From previous studies [Yunes et al (2006)], it was found that an interfacial reaction occurs,
producing SiC as interfacial product, and that this reaction played a significant role in
dynamic wetting. XRD scanning (Figures 4-16 to 4-18) at the interface ferroalloy / synthetic
SiC appeared 30 seconds after melting for Si 98.5% and the formation of SiC at the interface
of FeSi 74% / graphite was observed 60 seconds after melting, while for FeSi 24.7%, the SiC
The experimental result of carbon dissolution runs on SiC substrates is discussed in the next
section along with an understanding of the influence of the interfacial SiC formation on the
5.3 Carbon dissolution from SiC substrates into ferrosilicon and silicon at
1550 °C
Carbon dissolution was also investigated from SiC substrates at 1550 °C. The availability of
data in this case was limited by occurrence of the dynamic wetting which restricted the time
frame for Si 98.5 and FeSi 74 experimental runs to a maximum of 60 seconds. Results from
carburization experimental runs using SiC as substrate are shown on Fig 5-8 to 5-10. It was
observed that the carbon pickup from SiC occurred at much lower levels compared to
synthetic graphite.
97
Chapter 5 Carbon Dissolution
0.05
0.045
0.04
0.035
0.03
C (wt%)
0.025
0.02
0.015
0.01
0.005
0
0 20 40 60 80
Time (seconds)
0.06
0.05
0.04
C (wt%)
0.03
0.02
0.01
0
0 20 40 60 80
Time (seconds)
Figure 5-9: Carbon pickup from SiC into FeSi 74% at 1550 °C
98
Chapter 5 Carbon Dissolution
0.07
0.06
0.05
C (wt%) 0.04
0.03
0.02
0.01
0
0 20 40 60 80
Time (seconds)
Figure 5-10: Carbon pickup from SiC into FeSi 24.7% at 1550 °C
Experimental runs were carried out on 85% SiC plates using the sessile-droplet method. The
experiments were performed under conditions similar to the ones described earlier on
synthetic graphite crucible. Comparisons between rate constants on both substrates were
plotted for each ferroalloy tested (Figures 5-11 to 5-13). As expected, the carbon dissolution
rate constant from SiC substrates was an order magnitude smaller compared with the rate of
carbon dissolution, as shown in Tables 5-1a and b. The formation of SiC as interfacial
product creates some resistance to the carbon diffusion from the graphite substrate and
therefore, has a retarding effect on the overall process. It was also observed that, despite
being of similar order, the rate constants changed significantly for each composition; the rate
constant for FeSi 24.7 was double that of FeSi74 and was almost three times that of Si 98.5.
(Table 5-2). This suggests that the process is favoured by lower silicon (or correspondingly
99
Chapter 5 Carbon Dissolution
Time(seconds)
0 50 100 150 200
0
-0.1 y = -0.00017x
-0.2
ln{(Cs-Ct/Cs-Co)}
-0.3
-0.4
-0.5 Si 98.5 /graphite
-0.6 y = -0.0038x
Si 98.5 /SiC
-0.7
-0.8
(Cs Ct )
Figure 5-11: Plot of ln vs. time (seconds) for carbon dissolution runs of Si 98.5%
(Cs Co)
on graphite and SiC substrates at 1550 °C.
Time(seconds)
0 50 100 150 200
0
-0.1 y = -0.0004x
-0.2
ln{(Cs-Ct/Cs-Co)}
-0.3
-0.4 y = -0.003x
-0.5
100
Chapter 5 Carbon Dissolution
Time(seconds)
0 50 100 150 200
0
-0.1
-0.2 y = -0.0008x
ln{(Cs-Ct/Cs-Co)}
-0.3
-0.4
-0.5
-0.6 FeSi24.7/graphite
-0.7 FeSi 24.7 /SiC y = -0.0039x
-0.8
(Cs Ct )
Figure 5-13: Plot of ln vs. time (seconds) for carbon dissolution runs of
(Cs Co)
FeSi24.7%on graphite and SiC substrates at 1550 °C.
Table 5-1a Constant rates and Carbon saturation limits for Si 98.5, FeSi 74 and FeSi 24.7
from synthetic graphite substrate.
Table 5-1b Constant rates and Carbon saturation limits for Si 98.5, FeSi 74 and FeSi 24.7
from SiC substrate.
101
Chapter 5 Carbon Dissolution
Table 5-2. Overall rates constant for ferroalloys tested on different substrates (s-1)
Substrate
The overall rates of carbon dissolution from graphite are quite similar for each sample. The
carbon diffusion process occurs remarkably faster at initial stages but after the initial pickup,
the appearance of SiC plays a retarding effect and slowed down the overall process. It can be
concluded that the carbon dissolution process in silicon and ferrosilicon alloys is governed
initially by diffusion and beyond this stage; the process is governed by mixed control
(including interfacial resistance by SiC), which slows down the rate of carbon dissolution.
The free diffusion of carbon occurs preferentially during the initial stages of the metal-
substrate interaction. The carbon pickup occurs at similar rates across the ferroalloys and it
was commonly observed that the carbon content rapidly increases at early stages. Carbon
saturation levels (Cs) are consistent with the rate constant of the carbon dissolution reaction
and this suggests that carbon diffusion is the primary mechanism in the initial stage. At the
same time, it was observed that SiC appeared as the interfacial product, providing an
interfacial resistance and slowing down the carbon dissolution from graphite.
102
Chapter 5 Carbon Dissolution
5.5 Summary
The carbon dissolution from synthetic graphite and the effect of SiC as interfacial product in
ferrosilicon alloys was studied. This work investigated the kinetic mechanism of carbon
dissolution reaction. The following conclusions have been drawn from the results:
- The overall rate constants do not present significant differences across the
carbon dissolution. However, the faster rate in the case of FeSi 24.7 can be
- The appearance of SiC as interfacial product plays a retarding effect on the overall
process and dictates the carbon transfer. This layer appears at very early stages of
the process for Si 98.5 and FeSi 74, while it takes longer to be formed for FeSi
24.7.
- The kinetics of carbon dissolution for FeSi 24.7, FeSi 74 and Si98.5% is driven by
a mixed control mechanism, where both carbon diffusion and interfacial resistance
103
CHAPTER 6
Dynamic weight changes during the decarburisation and silicon oxidation reactions of the
molten ferrosilicon alloys during their interactions with oxidizing gases are presented in this
Investigations were carried out on carbon-rich ferroalloys (see Table 6.1). The
experimental runs were carried out on three ferrosilicon alloys respectively containing 24.7
wt%, 74 wt% and 98.5 wt% Si. The specimens were held in a (20% CO2 – 2% CO – N2
(balance) gas mixture at flow rates of 0.5, 1 and 2.0 L/minute. The % weight gain
(W*100/Wo; where W and Wo respectively represent the net weight change and initial
weight) as a function of time is shown in Figure 6-1 for three specimens under investigation.
It is to be noted that y-axis scales are different for Figures 6-1(a-c) indicating significant
differences in weight changes; x-axis covers a much longer time scale in Figure 6-1 c.
For a gas flow rate of 1 L/min, weight gains were quite comparable for Si 98.5 and FeSi
74. Both showed ~10% weight gain after 10 minutes. The weight gain however was very
slow for FeSi 24.7, reaching a 2% weight gain after 30 minutes. For a gas flow rate of 0.5
L/min, weight gains were once again quite comparable for Si 98.5 and FeSi 74. Both showed
~3% wt. gain after 10 minutes. FeSi 24.7 showed almost no weight gain for the initial 15
minutes and then increased marginally to 0.5% after 30 minutes. Much higher weight gains
were observed for gas flows of 2 L/min. The weight of Si 98.5 increased sharply reaching a
massive 37% after 10 minutes. The increase was relatively slower for FeSi 74, which reached
a maximum of 12%. The weight gain for FeSi 24.7 continued to be slow, reaching a
maximum of 2.7% after 30 minutes. (Table 6.2). A closer comparison of the weight gain
104
Chapter 6 Silicon oxidation and Decarburisation
under 2 L/min flow rate for all samples during the initial ten minutes is shown in Figure 6-1
d.
Fe Si C Al
Si 98.5 0.72 98.52 0.12 0.03
Table 6-2: Weight gains (%) for different silicon and ferrosilicon alloys during the first
minutes. Oxidising gas 20% CO2, 2% CO, N2-balance was used at flow rates ranging
between 0.5 to 2 L/min.
105
Chapter 6 Silicon oxidation and Decarburisation
Figure 6-1 a –c: % Weight gain for three alloys as a function of time. Oxidising gas 20%
CO2, 2% CO, N2-balance was used at flow rates ranging between 0.5 to 2 L/min.
106
Chapter 6 Silicon oxidation and Decarburisation
40
35
30
25
% Weight gain
20
15
10
0
1 2 3 4 5 6 7 8 9 10
Time
Si 98.5 FeSi 74 FeSi 24.7
Figure 6-1 d: % Weight gain for three alloys during the initial 10 minutes. Oxidising gas
20% CO2, 2% CO, N2-balance was used at flow rates of 2 L/min.
6.2 Study of the carbon loss for silicon and ferrosilicon alloys
In Figure 6-2, we have plotted wt% C in three specimens for a range of gas flow rates as a
function of time. Noticeable decarburization was observed across the whole range of samples
during the first 2 minutes. It is to be noted that same x and y axes have been used in Figure 6-
2 (a-c). This effect was most remarkable for FeSi 24.7, where carbon levels dropped by 0.11
wt% C, followed by FeSi 74 (0.08 %C) and Si 98.5 (0.07%C) within 120 seconds. After this
period, the decarburization appeared to occur at a much slower rate. For a gas flow rate of 1
L/min, the carbon content in Si 98.5 fell from 0.12%C to 0.04%C after 10 minutes of contact.
For FeSi 74 alloy, the carbon content decreased from 0.09% to 0.01%C after 10 minutes. For
FeSi 24.7, the carbon level decreased from 0.14% to 0.05% after 10 minutes. A closer
comparison of carbon losses for the initial period is presented in greater detail in Figure 6-2
d. The influence of gas flow rate on decarburisation was not found to be very significant, and
107
Chapter 6 Silicon oxidation and Decarburisation
similar trends were observed. For Si 98.5, while no difference was observed for 0.5 L/min
and 1 L/min flow rates, increased decarburisation was observed for 2 L/min, indicating the
influence of the gas phase mass transfer mechanism. Gas flow rate had a negligible influence
on the decarburisation of FeSi 74 alloy. A small improvement with flow rate was observed
In Figure 6-3, we have plotted %C in three specimens after exposure to two oxidising
gases (20% CO2 – 2% CO – N2-balance and 100% CO2); the gas flow rate was maintained at
kinetics with increasing CO2 level could be seen for FeSi 74 and FeSi 24.7 alloys, a marginal
increase in decarburisation was observed for Si 98.5 specimen. This change was observed
during the initial as well as in the later stages. Back-scattered images using the EPMA (400X)
showed areas with substantial amounts of silica after only five minutes, particularly for high-
silicon alloys (Si 98.5 and FeSi 74). However, the appearance of silica for FeSi 24.7 was
found to occur at much later times. These are shown in Figures 6-4 (a-c)
108
Chapter 6 Silicon oxidation and Decarburisation
Figure 6-2 a-c: Wt % C for three alloys as a function of time. Oxidizing gas 20% CO2, 2%
CO, N2-balance was used at flow rates ranging between 0.5 to 2 L/min.
109
Chapter 6 Silicon oxidation and Decarburisation
0.16
0.14
0.12
0.1
0.08
0.06
0.04
0.02
0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5
Time (Minutes)
Figure 6-2 d: Change in carbon content (wt%) for different silicon and ferrosilicon alloys
during the first minutes. Oxidising gas 20% CO2, 2% CO, N2-balance was used at a flow rate
of 2 L/min.
110
Chapter 6 Silicon oxidation and Decarburisation
Figure 6-3: Wt% C for three alloys as a function of time. Two oxidising gas 20% CO2, 2%
CO, N2-balance and 100% CO2 were used at a flow rate of 1 L/min.
111
Chapter 6 Silicon oxidation and Decarburisation
Figures 6-5 (a-c) show the changes in silicon content for the silicon and ferrosilicon
flow rates between 0.5 to 2 L/min. At a flow rate of 0.5 L/min, silicon losses occurred at a
low rate consistently across all samples, the effect was almost negligible for FeSi 24.7.
However, at flow rate of 1 and 2 L/min for FeSi 74 and Si 98.5 the silicon losses were
significant from 2 minutes onwards; however for FeSi 24.7, higher silicon losses were
The silicon depletion from the metal samples and the subsequent silica formation are closely
related to the earlier weight gains results. This is clearly shown on figures 6-6 (a-c), where
the weight gains and silicon content changes versus time are plotted for each alloy. For Si
98.5 and FeSi 74 alloys, the rapid weight gains corresponded clearly with significant silicon
losses. After 10 minutes, weight gains for both alloys are around 10 percent, while silicon
losses are also in the same order. However, for FeSi 24.7, both, silicon losses and weight
Figures 6-7 (a-c) show the relationship between silicon content changes and the rate of
flow rate of 1 liter/minute for all silicon and ferrosilicon samples. The trends showed that the
rate of weight change increased very rapidly at the early stages but as the silicon content
decreases in the metal, the weight gain also decreased. This is particularly noticeable for Si
98.5 and FeSi 74, whereas is less evident for FeSi 24.7.
112
Chapter 6 Silicon oxidation and Decarburisation
A1
Area A -C: 0.017 wt%, O: 0.47wt%, Si: 18.98 wt%, Fe: 79.91 wt%
B2 B1
113
Chapter 6 Silicon oxidation and Decarburisation
C2
C1
Figure 6-4 a-c. Back-scattered electron EPMA images. Atmosphere: 20% CO2 – 2%
CO. Flow rate: 2 L/min
114
Chapter 6 Silicon oxidation and Decarburisation
100
90
80
70
60
0 2 4 6 8 10
75
70
65
60
0 2 4 6 8 10
25
24.5
24
23.5
0 10 20 30
Figure. 6-5 a- c: Change in silicon content (wt %) for the three alloys during the first
minutes. Oxidising gas 20% CO2, 2% CO, N2-balance was used at flow rates ranging from
0.5 to 2 L/min
115
Chapter 6 Silicon oxidation and Decarburisation
12
98
10
95.5 8
Si (wt%)
4
90.5
2
88 0
0 2 4 6 8 10
Time (minutes)
Silicon Content (wt%) weight gain
Figure 6-6a: Changes in silicon content (wt%) and weight change (%) for Si 98.5 during the
first ten minutes. Oxidising gas 20% CO2, 2% CO, N2-balance .Flow rate 1 L/min
116
Chapter 6 Silicon oxidation and Decarburisation
75 12
10
72.5
8
70 6
4
67.5
2
65 0
0 2 4 6 8 10
Figure 6-6 b: Changes in silicon content (wt%) and weight change (%) for FeSi 74 during
the first ten minutes. Oxidising gas 20% CO2, 2% CO, N2-balance .Flow rate 1 L/min
24.8 2
24.6 1.5
Silicon
24.4 1
Weight gain (%)
24.2 0.5
24 0
0 10 20 30
Figure 6-6 c: Changes in silicon content (wt%) and weight change (%) for FeSi 24.7 during
the first thirty minutes. Oxidising gas 20% CO2, 2% CO, N2-balance .Flow rate 1 L/min
117
Chapter 6 Silicon oxidation and Decarburisation
2.5
1.5
0.5
0
87 89 91 93 95 97 99
3
Weight change rate (%/min)
2.5
2
1.5
1
0.5
0
66 68 70 72 74 76
0.12
0.1
0.08
0.06
0.04
0.02
0
24.1 24.2 24.3 24.4 24.5 24.6 24.7 24.8
Silicon (wt%)
Figure. 6-7 a- c: Plot of rate weight change ( %/min) vs. Silicon content (wt%) for the three
alloys during the first minutes. Oxidising gas 20% CO2, 2% CO, N2-balance was used at flow
rates of 1 L/min
118
Chapter 6 Silicon oxidation and Decarburisation
6.5 Discussion
Decarburisation and silicon oxidation are the two key reactions occurring under these
experimental conditions. Decarburisation reactions can lead to the loss of carbon, generating
a gaseous product and an associated weight loss. Silicon oxidation reactions on the other
hand produce silica resulting in weight gain. When both reactions occur simultaneously, it
was seen clearly that the net weight gain is the resultant of decarburization and silicon
oxidation reactions. FeSi 24.7 showed a negligible weight change during the first 10 minutes.
Although it was observed that the decarburization occurred fairly quickly during the first 120
seconds, a steady slope later on suggests that the reaction kinetics slowed down after that.
With silicon oxidation reaction also occurring during the same period, it appears that the
weight loss due to decarburization was balanced by the weight gain through silica formation,
thereby resulting in no weight gain during initial 120 seconds. However as decarburisation
slows down after 120 seconds, the weight gain through silicon oxidation becomes higher and
a net weight increase can be clearly observed. Lowest level of weight gain was observed for
FeSi 24.7.
Oxidation reactions of C and Si in Fe-C-Si melts with CO2 are represented below by
In Figure 6-8, we have plotted wt% C as a function of time for three alloys with two
oxidising gaseous atmospheres (20% CO2, 2% CO, N2-balance; flow rate 1 L/min.) using a
logarithmic scale along the y-axis. There is a clear evidence for an exponential decay and two
rate regimes, labeled as I and II. The rate of decarburisation was much higher in region I,
119
Chapter 6 Silicon oxidation and Decarburisation
which lasted during the initial 2 minutes. It is important to note that FeSi 74 showed the
highest rate of decarburisation during initial 2 minutes as indicated by the highest slope. It
was also found that decarburization rate for FeSi 74 was much higher compared to Si 98.5 in
A significant slowing down in the decarburisation rate was observed in region II, even though
there were still significant amounts of carbon remaining in the alloys Si 98.5 and FeSi 24.7
(see Fig. 6-3 (a & c,). This observation suggests that, during silicon oxidation, it is
thermodynamically feasible that carbon content in the melt had increased according to
Equation (6-2) and could explain the decreasing of the decarburization rate in region II.
Although the decarburization reaction occurred rapidly for FeSi 74 and Si 98.5 during early
120
Chapter 6 Silicon oxidation and Decarburisation
stages, the rapid weight increases observed for both samples and the slower decarburization
rates suggest that silicon oxidation prevailed over the decarburization. This is further
confirmed by the significant decreases in silicon content observed during the first minutes for
Si 98.5 and FeSi 74. These results are in sharp contrast with FeSi 24.7, where the
decarburization occurred in preference to silicon oxidation during the initial stages. Thus, the
net “balance” between both the decarburization and silicon oxidation kinetics could explain
the fact that both reactions occurred simultaneously, explaining the absence of weight change
until after 10 minutes. It is not until then that the silicon oxidation reaction was seen to
prevail clearly over to the decarburization. However, the weight gain is considerably lower
compared to the Si 98.5 and FeSi 74, which indicate that the desiliconization rate for FeSi
24.7 is slower compared to other two alloys under investigation. (Figure 6-7 a to c)
From the flow rate data, it can be seen that the decarburization followed a trend similar
with increasing gas flow rates, i.e., the reaction rate showed a sharp increase during the first
120 seconds, followed by a steady slope. This feature can be observed more clearly for the
flow rate of 2 L/min. This suggests that the decarburization rate bears a direct correlation
with the flow rate and indicates a key role played by mass transfer in the gas phase. Silicon
oxidation rates also followed a similar trend as previous results for flow rate of 1 L/min.
increased flow rates, suggesting that the mass transfer of CO2 was a dominant step. A
qualitative analysis for both, carburisation and oxidation reactions for Si 98.5, FeSi 74 and
121
Chapter 6 Silicon oxidation and Decarburisation
Table 6.3: Qualitative comparison of carbon dissolution and oxidation reaction rates
From the cupola process perspective, these findings suggest that the use of ferrosilicon
alloy with lower silicon content might help to minimise silicon losses. There are of course,
other considerations such as cost and availability that need to be taken into account. Our
results have shown that the silicon oxidation reaction was intensified when the gas flow rate
was doubled. This factor should also be weighed carefully when cupola operational
parameters such as blast rate and blast volume are chosen, as these may affect the gas flow
and velocity of the gases generated in the combustion zone of the cupola.
1) An in-depth study has been carried out on the oxidation reactions at 1550 °C in Fe-Si
alloys with high silicon contents. Under the experimental conditions, both
2) The net weight gain in alloys was found to be the result of decarburization (weight
loss due to the generation of a gaseous product) and silicon oxidation (weight gain
due to silica formation on the surface of the sample). Key differences in weight gain
3) There was a clear evidence for two rate regimes, labeled as I and II. The rate of
decarburisation was much higher in region I, which lasted during initial 2 minutes; a
122
Chapter 6 Silicon oxidation and Decarburisation
much slower rate was observed in the later stages for all three alloys. No significant
effect was found on the decarburization rates when the relative proportion of the
4) For FeSi 24.7 alloys, the decarburization reaction appeared to prevail during the first
120 seconds. The rapid drop in carbon content during the early stages suggests that
decarburization reaction slowed down, silicon oxidation was able to take over.
5) For FeSi 74 and Si 98.5 alloys, decarburization rates followed a similar trend but were
relatively slower. The silicon oxidation reaction appeared to be the dominant reaction
6) Decarburisation did not change significantly for FeSi 24.7 and Si 98.5 under a gas
flow rate of 0.5 and 1 L/min, but noticeable changes were observed when the gas flow
rate was increased to 2 L/min. This suggests that the mass transfer in the gas phase
played an important role in the decarburisation reaction for those alloys. This however
123
CHAPTER 7
7.1 Introduction
A fundamental investigation has been carried out on the high temperature interaction between
ferrosilicon and graphite; key knowledge for understanding the interfacial reaction and it
relationship with the surface tension phenomenon has been developed. Using the sessile
droplet method, the dynamic wetting of synthetic graphite by liquid ferrosilicon alloys
containing 24.7 and 74 % Si and silicon (98.5 % Si) at 1550 °C has been reported. The study
of the wetting parameters, such as contact angle, when liquid metal droplets interact with
graphite substrate was found to be of significant importance during this process. The
influence of the interfacial product formed and its relationship with the dynamic wetting
Carburization is a key reaction for the scrap-iron process, since the metallic liquid droplets
combine with the coke at high temperatures. The kinetic mechanism of carbon dissolution in
liquid iron had been extensively investigated. However, there is little, if any knowledge about
the kinetics of carbon dissolution when the silicon content is higher than 10%. Although the
thermodynamics of Fe-Si-C system has been well studied, the kinetics of this system has not
been investigated in depth. Therefore, the study of the reaction kinetics and interfacial
phenomena can provide a better fundamental understanding of the carbon dissolution process
occurring during ferrosilicon-carbon interaction. In this study, a kinetic mechanism has been
developed for the carbon dissolution phenomena in ferrosilicon alloys. The overall-rate
constants at 1550 °C were found for Si 98.5, FeSi 74% and FeSi 24.7%. The influence of
In the cupola furnace, decarburization and silicon oxidation reactions are known to occur
extensively during the scrap melting process as oxidising gases react with the molten metal.
125
Chapter 7 Summary and Conclusions
From the process perspective, the oxidation of silicon needs to be controlled since excessive
silicon oxidation can affect the quality of the cast iron product. Additionally, the wasted
silicon forms silica, which increases the slag volume eroding more aggressively the basic
refractory lining and slag capacity. Silicon oxidation and decarburization studies in
steelmaking have generally been limited to Fe-based alloys containing up to 3.5 wt% Si. This
thesis ,have presented high temperature investigations on ferrosilicon alloys with Si contents
of 24.7 wt% and 74 wt% and a silicon alloy containing 98.5 wt% Si. The present work
evaluates the effect of the alloy composition, oxygen partial pressure and flow rate on
interactions at 1550 °C. Significant differences were observed in the weight gain and carbon
loss between these three alloys; both decarburisation and silicon oxidation reactions were
found to occur simultaneously. There was also a clear evidence for two rate regimes: the rate
of decarburisation was found to be much higher during the initial 2 minutes and a much
slower rate was observed in later stages for all specimens. These rate regimes have been
explained in terms of the extent of surface coverage with the reaction product silica. No
significant effect was found on the decarburization rates when the proportion of oxidizing gas
(CO2) was increased from 20 to 100%, indicating that mass transfer in the gas phase was not
a dominant rate controlling step compared to chemical kinetics. The net weight gain in these
alloys was found to be due to the combined influence of decarburization (weight loss due to
the generation of a gaseous product) and silicon oxidation (weight gain due to silica
formation on the sample surface). The outcomes of this investigation will assist with the
development of mechanisms governing the reactions of the molten ferrosilicon and silicon
alloys during their interactions with gaseous phases in the cupola process.
126
Chapter 7 Summary and Conclusions
Graphite.
Silicon 98.5% and ferrosilicon alloys containing 74 and 24.7% Si showed good wetting
behaviour (θ < 90º) on synthetic graphite at 1550 °C. The initial contact angles for Silicon
98.5, ferrosilicon 74 and 24.7 were respectively 105,140 and 112°. Full wetting was observed
for silicon 98.5 and ferrosilicon 74 within the first 90 seconds (Figures 4-4, 4-5). However,
the final contact angle value appeared higher for the low-silicon ferroalloy (24.7 wt% Si) and
The presence of interfacial product was likely to occur as per equation 4.1:
At 1550 °C, the Gibbs free energy for SiC = -5.58 x 104 J, so the reaction is
interfacial product. Reported results from Nogi and Ogino [Nogi and Ogino (1988)] and
Nikolopoulos et al [Nikolopoulos et al (1992)] showed good wetting between silicon and SiC,
so this explains the good wetting behaviour observed when silicon and ferrosilicon alloys
interacted with synthetic graphite. It was also found that the rate of formation of SiC at the
interface between ferrosilicon and synthetic graphite was different for different ferroalloys.
The formation of SiC at the interface appeared 30 seconds after melting for si 98.5, while this
was observed for FeSi 74 after 60 seconds. However, for FeSi 24.7, the SiC was detected
after 30 minutes.
127
Chapter 7 Summary and Conclusions
Further wettability investigations carried out on SiC substrates showed similar trends as the
ones observed on synthetic graphite. The initial contact angles for Si 98.5, FeSi 74 and FeSi 2
were 88.6, 134 and 92 degrees respectively. Full wetting was observed for Si 98.5 and FeSi
74 after 80 and 90 seconds, while FeSi 24.7 showed a different pattern, since the contact
angle decreased rapidly during the first 10 minutes and remained steady around 40 degrees
after that time. These results, together with the X-ray diffraction findings, explained the
wettability phenomena between silicon and ferrosilicon alloys with synthetic graphite and the
differences on dynamic wetting between high and low silicon alloys. The dynamic wetting
interface.
Carbon dissolution phenomenon and associated mechanisms are established for ferrosilicon
alloys at 1550 °C in this investigation. The overall rate constants at 1550 °C for Si 98.5, FeSi
74 and FeSi 24.7 were 3.8,3 and 3.9 x 10-3 (s-1) respectively. Since the overall rate constants
do not present significant differences across the samples, it is suggested that carbon diffusion
increased of carbon pickup during the first few minutes, remaining fairly constant after this
period.
The role of SiC as interfacial product and its impact on dynamic wetting between silicon and
ferrosilicon alloys with synthetic graphite have been discussed on section 7.2. Carbon
dissolution on silicon and ferrosilicon alloys from SiC substrates was also investigated. It was
found that the overall rate constants for Si 98.5, FeSi 74 and 24.7 were 1.7,4 and 8 x 10-4 (s-
1
), being one order of magnitude smaller compared with the rate of carbon dissolution from
synthetic graphite. The formation of SiC as interfacial product creates a barrier effect, thus
128
Chapter 7 Summary and Conclusions
retarding the carbon diffusion process. Despite that the rate constants are in the same order of
magnitude, FeSi 24.7 is double than FeSi 74.7 and almost three times compared to Si 98.5%.
This suggested that the carbon diffusion is favoured by lower silicon (or higher iron) contents
in the ferroalloy.
The carbon pickup occurs at similar rates across the ferroalloys and it was found that the
carbon content increased rapidly at early stages. Carbon saturation levels were consistent
with the rate of carbon dissolution, suggesting that carbon diffusion is the primary
mechanism in the initial stage. At the same time, the formation of SiC as interfacial product,
plays a retarding effect and slowing down the carbon dissolution from graphite.
The faster rate in the case of FeSi 24.7 can be explained on the basis of delayed formation of
SiC interfacial product. The appearance of SiC as interfacial product played a retarding effect
on the overall process and dictated the carbon transfer. As discussed on section 7.2, SiC
layer appeared at very early stages of the process for Si 98.5 and FeSi 74, while it took longer
Ferrosilicon Alloys
The interactions between ferrosilicon and silicon alloys with synthetic graphite were
investigated from the perspective of the interfacial phenomenon and their implications in
wettability and carburisation reactions. Both above-mentioned processes occurred inside the
cupola furnace when molten ferrosilicon interacts with coke, thus the significance of this
investigation. It should be noted that an oxidizing gas phase is generated inside the furnace
and interacted with rich-carbon ferroalloys molten droplets that are descending to the burden.
This thesis investigates the decarburisation and silicon oxidation reactions that took place
129
Chapter 7 Summary and Conclusions
It was found that, both decarburisation and silicon oxidation reactions were found to occur
simultaneously. There was a clear evidence for two rate regimes, labeled as I and II on Figure
6-8. The rate of decarburisation was much higher in region I, which lasted during initial 2
minutes; a much slower rate was observed in the later stages for all three alloys. No
significant effect was found on the decarburization rates when the relative proportion of the
For FeSi 24.7 alloys, the decarburization reaction appeared to prevail during the first 120
seconds. The rapid drop in carbon content during the early stages suggests that
decarburization rate was higher compared to silicon oxidation. Once the decarburization
reaction slowed down, silicon oxidation was able to take over. For FeSi 74 and Si 98.5 alloys,
decarburization rates followed a similar trend but were relatively slower. The silicon
The net weight gain in alloys was found to be the result of decarburization (weight loss due to
the generation of a gaseous product) and silicon oxidation (weight gain due to silica
formation on the surface of the sample). Key differences in weight gain were observed
between three alloys under investigation. Decarburisation did not change significantly for
FeSi 24.7 and Si 98.5 under a gas flow rate of 0.5 and 1 L/min, but noticeable changes were
observed when the gas flow rate was increased to 2 L/min. This suggests that the mass
transfer in the gas phase played an important role in the decarburisation reaction for those
alloys. This however was not the case for FeSi 74.
7.5 Conclusions
The main aim of this investigation is to understand the fundamentals during the interactions
between ferrosilicon and silicon alloys with carbon bearing materials and impact of the
oxidizing gas phase. There were three different aspects that were investigated in depth:
130
Chapter 7 Summary and Conclusions
wetting.
- Carbon dissolution process during the interaction between ferrosilicon alloys and
synthetic graphite.
The three objectives of this research were largely achieved. A mechanism for the carbon
dissolution kinetics for ferrosilicon and silicon alloys was proposed. It was also found the key
role played by the SiC as an interfacial product in both, carbon dissolution and dynamic
wetting phenomena. These results have also provided fundamental understanding during the
decarburisation and silicon oxidation reactions after the carbon-rich ferroalloys interacted
with the oxidizing gas phase. The outcomes provide valuable information for cast iron
bearing materials in the metallic charge and to achieve the optimum atmosphere in the
furnace in order to achieve the best possible silicon recovery during the cupola process.
131
Chapter 7 Summary and Conclusions
This investigation established the carbon dissolution kinetics for silicon and ferrosilicon
alloys. The carbon diffusion from synthetic graphite into the silicon and ferrosilicon alloys is
satisfactorily explained. However, during the cupola process, the carbon-bearing material
most commonly used is coke. Impurities contained in the coke might affect the carbon
dissolution reaction, as well as the wettability and this also might affect the decarburisation
and oxidation kinetics. Future work should be aiming to understand the impact of the
impurities on these processes, as well as determining the predominant rate controlling step
and oxidation kinetics. Numerical simulations and kinetic studies are also needed to study the
effect of Si content on wettability on different substrates and the effect of carbon content and
132
References
1. S. Katz, V.S., C. F. Landefeld and M. E. Bauer, Modern Casting
1999. 89(6): p. 41.
5. Luis, C.J., Ugalde, M. J., Puertas, I, J. Mat. Process. Tech, 2002. 120: p. 281-289.
6. CUPOLA HANDBOOK. 5th Edition ed, ed. A.F.m.s. Society. 1984, Illinois: Des
Plaines
136-139.
8. Hultgren, R., Desai, P. D., Hawkins, D.T., Gleiser, M., Kelley, K.K, ed. Selected
Values of the Thermodynamic Properties of Binary Alloys., ed. ASM. 1973, Metals
11. Übelacker, E., Mem. Sci. Rev. Metall., 1967. 64: p. 183-190.
15. Hofmann, D.H., Müller, M. H., Mat. Sci. & Eng., 1999. Vol. B 61-62 p. 29-39.
16. Sorrell, C.C., Key Eng. Mat., 1995. 111 –112 p. 127-156.
17. Gaskell , D.R., ed. Introduction to the thermodynamics of materials. 3rd Edition ed.
133
18. Levenspiel, O., Chemical Reaction Engineering. 2nd ed. 1976: Wiley International
Edition. 12.
19. Olson, R., G., Koump, V., Perzak, T.F. Trans. TMS-AIME, 1966. 236: p. 426-429.
20. Kosaka, M., Minowa, S, Trans. Iron Steel Japan, 1968. 8: p. 392-400.
21. Oersten, S., Oeters, F. Process Technology Proc. in 5th Int. Iron Steel Congress.
1986: ISS-AIME
22. Wright, J.K., Baldock, R.B., Metall. Trans., 1988. 19B: p. 373-378.
24. Zhao, L., Interfacial Phenomena and Chemical Reactions during Interactions of Iron
27. Cham, S.T., Sahajwalla,V.,Sakurovs, R.,Sun,H. and Dubikova, M., ISIJ International,
30. Nozaki T., Y.Y., Akiyama, N., J. Electrochem. Soc., 1970. 117: p. 1566.
31. Oden, L.L., McCune, R.A., Met. Trans. , 1987. 18A: p. 2005.
32. Suhara, S., Yuge, N., Fukai, M., Aratani, F., CAMP-ISIJ, 1989. 2: p. 1341.
33. Ottem, L., Løselighet og termodynamiske data for oksygen og carbon I flytende
34. Yanaba, K., Akasaka, M., Takeuchi, M., Watanabe, M., Narushima , T., Iguchi, Y.,
35. Naidich, J.V., Progress in Surface and Membrane Science1981. 14: p. 428.
134
36. Klevan, O.S., Removal of C and SiC from Si and FeSi during ladle refining and
Tronheim.
37. Ray, H.S., Kinetics of Metallurgical Reactions. 1993, New York: International
Science Publisher.
38. Sain, D.R., Belton, G.R., Met. Trans., 1978. 9B: p. 403-407.
40. Sano, M., Yetao, H., Kato, M., Sakamoto, S., ISIJ International, 1994. 34: p. 657.
41. Ahmadi Najafabadi, M., Hirasawa, M., Sano, M., ISIJ International, 1997. 37: p31.
42. Sain, D.R., Belton, G.R., Met. Trans., 1976. 7B: p. 235-244
43. Mannion, F.J., Freuhan, R.J., Met. Trans., 1989. 20B: p. 853-861.
44. Ono-Nakazato, H., Morita, Y., Tamura, K., Usui, T., Marukawa, K, ISIJ International,
45. Taguchi, K., Ono-Nakazato, H., Usui, T., Marukawa, K. , Met. Trans., 2003. 34B: p.
861-867.
46. Sakaguchi, K., Maeda, M., Met. Trans., 1992. 23B: p. 423.
47. Anderson, N.M., Engh, T. A., Factors Affecting Bubble Residence Times in Gas
Purged Reactors and Their Influence on Mass Transfer, in STF34 A87087. 1987,
SINTEF Division of Metallurgy.
48. Iguchi, M., Nozawa, K., Tomida, H.and Morita, Z., ISIJ International, 1992. 32: p.
747-754.
49. Richardson, F.D. in The Chipman Conference. 1962. Cambridge, MA: J.F. Elliot and
Meadowcraft.
51. Berg, J.C., Wettability. 1st. ed. 1993, NY: Marcel Dekker Inc. 3.
135
53. Kobayashi, H., Azuhata, S., Morita, S., Transactions of Japan Institute of Mechanical
54. Ottewill, G., Gaudin, A.M., Flotation. 1957, New York: MacGraw-Hill. 163.
55. Adamson, A.W., Physical Chemistry of Surfaces. 5th ed. 1990, New York: John
56. Zelinski, B.J., Cronin, J. P., Denseuk, M. and Uhlman, D.R., Wettability. 1993: Berg,
57. Lou, X., Boyd, R., Kent, J. H., J.of the Institute of Energy, 1991. 64(461): p. 230-238.
58. Blake, T.D., Wettability. Dynamic Contact Angle and wetting kinetics. 1993: Berg,
59. Bashforth, F., Adams, J.C., An attempt to test the theories of capillary action. 1883,
62. Maze, C., Burnet, G., Surface Science, 1969. 13: p. 451-470.
63. Rotenberg, R., Borucvk, L., Neumann, A.W., J. Cellulloid and Interface Science,
64. Jimbo, L., Sharan, A., Cramb, A.W. Recent measurements of surface and interfacial
65. Sharon, A., Cramb, A.W., Met. Trans., 1997. 28B: p. 465-472.
67. Mehta, A.S., Sahajwalla, V., Scand. J. of Metall., 2000. 29: p. 17-29.
68. Kozakevitch, P., Chatel, S., Urbain, O., Sage, M., Rev. Metall., 1955. 52: p. 139-160.
69. Jimbo, L., Cramb, A.W., ISIJ International, 1992. 32(1): p. 26-35.
70. Espie, L., Drevet, B., Eusthapoulos, Met. Trans., 1994. 25A: p. 599.
136
71. Sharan, A., Cramb, A.W., Met. Trans., 1997. 28B: p. 465-472.
73. Humenik, M.J., Kingery, W.D., J. Am. Ceram. Soc., 1954. 37(1): p. 18.
75. Sun, H., Mori, K., Sahajwalla, V., Pehkle, R. , High Temp. Mater. Process., 1998. 17:
p. 257.
77. Nogi, K., Ogino. Wettability of Silicon Carbide by Liquid Metals. in Proc. Int. Symp.
78. Kapilashrami, E., Reactions between Oxygen-Containing Iron Melts and Dense
80. Ottem, L., Løselighet og termodynamiske data for oksygen og carbon I flytende
81. Zhao, L., Interfacial Phenomena and Chemical Reactions during Interactions of Iron
83. Mehta, A.S., Sahajwalla, V., Scand. J. of Metall., 2000. 29: p. 17-29.
137
APPENDIX I
Dynamic wetting investigations were also carried out for ferrosilicon and silicon alloys on
natural graphite (Figures A-1,A-2 and A-3). It was found that these alloys displayed very
good wetting in natural graphite, comparable to the one found in synthetic graphite (Figure
These findings, although very revealing, it created further difficulties for the carburization
investigations, since no reliable results for carbon analysis from the metallic sample analysis
was possible. At the time that the experimental work was carried out, not natural graphite
crucibles were available for the experimental work, so it was decided that the carburization
The wetting of Si 98.5 wt% displayed similar trend for both, synthetic and natural graphite
substrates. The initial contact angle for synthetic graphite was 105º , while this value was
88.6º for natural graphite. After 80 seconds, the contact angle for synthetic graphite decreased
The wettability study for FeSi 74 wt% showed similar trend to the one observed for Si 98.5
wt%. The initial contact angle values on synthetic and natural graphite were both similar
(140º). Both substrates displayed full wetting and the difference was on the time needed to
reach it. For synthetic graphite full wetting was reached after 90 seconds, while for natural
The dynamic wetting for FeSi 24.7 wt% displayed different pattern. The initial contact angle
for synthetic graphite (112º) and natural graphite (121º) decreased down to 99º and 102º
respectively after 60 seconds. After this time, the wetting showed slight improvement up to
600 seconds, when both substrates showed and steady trend around the 89º for natural
139
Appendix I
1 second) 10 seconds)
15 seconds) 18 seconds)
22 seconds) 28 seconds)
Figure A-1: Still image of liquid silicon (Si 98.5%) droplet on natural graphite substrate
140
Appendix I
1 second) 10 seconds)
30 seconds) 40 seconds)
45 seconds) 50 seconds)
Figure A-2: Still image of liquid ferrosilicon (75%) droplet on natural graphite substrate
141
Appendix I
1 second) 10 seconds)
Figure A-3: Still image of liquid ferrosilicon (25%) droplet on natural graphite substrate
142
Appendix I
120
60
40
20
0
0 10 20 30 40 50 60 70 80 90
Time (seconds)
160
100
80
60
40
20
0
0 20 40 60 80 100
Time (seconds)
143
Appendix I
140
FeSi25/synt. graphite
120
Contact Angle (degrees)
FeSi25/nat. graphite
100
80
60
40
20
0
0 1000 2000 3000 4000
Time (seconds)
Figure A-6: Dynamic wetting of FeSi 24.7 wt% for different substrates
144