Beruflich Dokumente
Kultur Dokumente
General Precautions
Vision Sensor yyDo not use this product for the purpose to
IV-500C / IV-500CA /
protect a human body or a part of human body.
yyThis product is not intended for use as an
explosion-proof product. Do not use this
IV-2000M / IV-2000MA
and performance before the start and the
operation of the IV Series.
yyWe recommend that you take substantial
safety measures to avoid any damage in the
Instruction Manual event of a problem occurring.
yyKEYENCE never warrants the function or
Read this manual before using the product in order to performance of the IV Series if it is used in manner
achieve maximum performance. that differs from the IV Series specifications
Keep this manual in a safe place after reading it so that it contained in this instruction manual or if the IV
can be used at any time. Series are modified by yourself.
For details of functions, refer to the IV Series User's Manual yyWhen the IV Series is used in combination with
(Monitor) or the IV Series User's Manual (PC). other instruments, functions and performance
yyThe IV Series User's Manual can be downloaded from the may be degraded, depending on operating
KEYENCE web site: conditions and the surrounding environment.
http://www.keyence.com/ yyDo not place the instruments, including
peripherals, under rapid temperature
Symbols change. It may cause condensation and may
damage instruments or peripherals.
The following symbols alert you to important messages. yyRemove the power cable from the power supply
Be sure to read these messages carefully. if you do not use this product for a long time.
It indicates a hazardous situation which, if not
avoided, will result in death or serious injury. Important Instructions
It indicates a hazardous situation which, if Observe the following precautions to prevent malfunction of
not avoided, could result in death or serious the IV Series and to ensure that it is used properly.
injury.
It indicates a hazardous situation which, if not Precautions on use
avoided, could result in minor or moderate yyThe power of this product and instruments
injury. connected to this product must be turned off
It indicates a situation which, if not avoided, when the cable is to be installed or removed.
could result in product damage as well as Failure to do so may cause an electric shock
property damage. or a product damage.
yyUse this product in the correct supply voltage.
It indicates cautions and limitations that must Failure to do so may cause a product damage.
be followed during operation.
Cautions
(1) Unauthorized reproduction of this manual in whole or
part is prohibited.
(2) The contents of this manual may be changed for
improvements without prior notice.
(3) An utmost effort has been made to ensure the contents of
this manual are as complete as possible. If there are any
mistakes or questions, please contact a KEYENCE office
listed in the back of the manual.
(4) Regardless of item (3), KEYENCE will not be liable for
any effect resulting from the use of this unit.
(5) Any manuals with missing pages or other paging faults
will be replaced.
The company names and product names used in this
manual are registered trademarks or the trademarks of their
respective companies.
Hexagon wrench
(L-shaped) x 1
Dome attachment x 1 5
Instruction Manual x 1
Polarized visible light filter attachment
yyOP-87436
Mounting screw x 2
Instruction Manual x 1
Polarized visible light filter
attachment x 1
Infrared polarization filter attachment
yyOP-87437
6
Mounting screw x 2
Instruction Manual x 1
7
Infrared polarization filter 8
attachment x 1
1 Sensor mounting adapter
Power I/O cable (M12 12pin - strand wire) Use this for mounting and fixing the sensor.
yyOP-87440 (2m) yyOP-87441 (5m) yyOP-87442 (10m) “Mounting” (Page 4)
2 Connector for power I/O cable
Connector for connecting a power I/O cable.
Use this for supplying power to the sensor and for
connecting with external devices.
“Cables” (Page 6)
3 Focusing position adjustment screw
Power I/O cable (M12 12pin - strand wire) x 1 (manual focus type only)
Mounting adapter Adjusts the focus of displayed images.
yyOP-87460 4 Connector for monitor cable/Ethernet cable
Connector for connecting a monitor cable or Ethernet
cable. Use this for connecting the monitor, PC, or Ethernet
Screw for mounting switch.
adapter x 1 “Cables” (Page 6)
When the cable is not connected, attach
Mounting adapter x 1 the waterproof cap for Ethernet connector
to maintain enclosure rating.
Same as the accessories for sensor. Tightening torque : 0.45 to 0.55 N·m
Optional parts in case of loss/damage.
5 Indicator light
Front cover (for replacement)
Indicates the operating status of the sensor.
yyOP-87461 “Operation of the indicator light” (Page 4)
6 Built-in light
Mounting screw x 2 LED light that illuminates the object.
Hexagon wrench 7 Camera
Front cover (for (L-shaped) x 1 Images the object.
replacement) x 1 O-shaped ring 8 Front cover
(Small x 2, Large x 1) Instruction Protects the camera and built-in lights.
Manual x 1
The front cover is protected by the protection sheet (blue)
Optional parts for replacement. in the default factory setting.
Bracket Remove the sheet when the sensor is to be used.
Front cover for replacement is provided for maintenance.
yyOP-87685×1
Mounting screw for
bracket + Nut x 1
500
400
300
200
150
100
50
0
25 50 70 100 130 150 200 250
210
View H (mm)
50
zz
Long-rang type
2500
Installed distance WD (mm)
2000
1500
1000
500
300
0
45 100 200 300 400 Push until you hear the clicking
View H (mm) sound from the both side stoppers
The value of View H and V will be a half of the value on
the figures above when using the digital zooming function 2 Fix the mounting adapter and sensor using the
attached screws.
(monochrome type only).
yyScrew : M3 x 1
Use the attached screws.
Mounting the mounting adapter yyTightening torque : 0.45 to 0.55 N·m
Use the mounting adapter (accessory or OP-87460) to
mount the sensor.
The mounting adapter is mounted on the
sensor in the default factory setting. Remove
it from the sensor.
“Unmounting the sensor” (Page 5)
Mounting on the wall
yyScrew : M3 x 4
Use the commercially available screws which have head
thickness of 3 mm or lower.
yyTightening torque : 1.0 N·m or lower Remove the protection
sheet (blue)
Mounting from the jig side
yyScrew : M4 x 4
Use the commercially available screws.
yyTightening torque : 1.5 N·m or lower
Black/White/Gray/ DC24V
Orange
(OUT) IN
Load
Blue (0V)
Adjust the pins and the
pin connection
Drain wire (FG)
Load
Brown
protection circuit
+3.3V
Overcurrent
Main circuit
OUT1 - OUT4
Main circuit
*
IN1 - IN6
*
0V
Blue
0V
* Black (OUT1) / White (OUT2) / Gray (OUT3) / Orange (OUT4)
Blue
Use by assigning the optional functions to OUT1 to OUT4
* Pink (IN1 : External trigger) / Yellow (IN2) / Light Blue (IN3) /
Purple (IN4) / Green (IN5) / Red (IN6)
When PNP output is selected
Use by assigning the optional functions to IN2 to 6 When PNP is selected in I/O format, the circuit becomes
Voltage input (When PNP output is selected) open collector PNP output circuit.
yyMaximum rating : 26.4 V, 50 mA
When PNP is selected in I/O format, the circuit becomes
yyRemaining voltage : 2 V or lower
voltage input circuit.
yyInput maximum rating : 26.4 V DC24V
yyON voltage : 15 V or higher Brown
yyON current : 2 mA (for 24V)
yyOFF current : 0.2 mA or lower
protection circuit
Overcurrent
Main circuit
DC24V
OUT1 - OUT4
Brown
*
Load
Main circuit
IN1 - IN6 0V
* Blue
Sensor
IV-500C / IV-500CA / IV-500M / IV-500MA / IV-150M / IV-150MA / IV-2000M / IV-2000MA
(102)
R
50
52
0
R5
(108) Focusing position adjustment screw
41 (MF type only)
50 0.4 81.5
10.5 6 3-M3
(Depth 6mm)
10.5
20.5
50
57.4
32.4
10.5
56 Mounting
adapter
58
1/4-20UNC
(Depth 6mm)
20
WD reference surface
45.5 25 4-M4
(Depth 6mm)
120 5
φ6.7
150 5
180 5
Bracket
OP-87685
0.4 112.5 56
50
48.4
93
31.6
19.6
99
(99) 58
41
82.5
E 1101-3