Beruflich Dokumente
Kultur Dokumente
html#prin_drive
The Den-Con HMB Hinged Pin Drive master bushing is available for 37 1/2" - 60 1/2" rotary tables.
The 49 1/2" - 60 1/2" HMB is rated 750 ton. The 37 1/2" - 49 1/2" HMB is rated 500 Ton. Removable
500 ton, 4 taper split insert bowls are available for both models to allow handling capability for 2 3/8" to
13 3/8" tubular products. 750 ton, 4 taper insert bowls are available upon request for the 49 1/2" - 60
1/2" HMB. The HMB can easily be removed from the drill string by removal of one hinge pin. The Den-
Con 27 RPH Roller Kelly Bushing is the drive bushing used with HMB 37 1/2" - 49 1/2".
The Den-Con SPB Solid Body Pin Drive master bushing is available for 20 1/2" - 27 1/2" rotary tables
and is rated 500 ton. Removable 500 ton, 4 taper split insert bowls are available to allow handling
capability for 2 3/8" to 13 3/8" tubular products. Refer to parts tables for casing bowls and sizes.
The Den-Con SMB Split Pin Drive master bushing is available for 17 1/2" - 27 1/2" rotary tables and is
rated 500 ton. The SMB is a split master bushing with the API 4 taper machined into the body halves
to handle 8 5/8" & smaller tubular products. This bushing is a split design to eliminate the need to strip
over the master bushing while running large tools during surface hole work. The SMB does not allow
for use of removable insert bowls. All of the pin drive master bushings have Pin drive hole locations to
API dimensions.
The Den-Con HMB Assembly, Parts and Bowls are interchangeable with Varco MPCH Bushings.
The Den-Con SPB Assembly, Parts and Bowls are interchangeable with Varco MSPC Bushings.
Ordering Information
Specify rotary table make, size and type when ordering.
*See Adapter Ring Data Table for additional details and configurations.
REMOVAL
1. Using an Acetylene torch, split worn bushings from top to bottom, in two place approximately
180 degrees apart.
2. Clean out drive holes, remove any rust and deburr the top edge.
Note: Place new drive hole bushing in a freezer to shrink.
INSTALLATION
1. Preheat the Master Bushing body around the drive hole area to 400-500°F.
2. Take drive hole bushing from freezer and place bushing in ice until ready to install.
3. Press drive hole bushing, chamfered end up, until flush with top of master bushing body.
4. If no press is available, make sure Master Bushing drive hole area is at the proper temperature.
Drive the drive hole bushing with a wooden block to seat drive hole bushing. Drive as rapidly
as possible using a sledge hammer.
37 49
QTY. 1/2” 27 1/2” 20 1/2” 27 1/2” 23” 20 1/2” 17 1/2” 27 1/2” 20 1/2” 1/2”
DESCRIPTIO
REQ’D HMB SPB50 SPB50 SSB500 SSB500 SSB500 SSB500 SMB50 SMB50 HMB
. N
500 0 TON 0 TON TON TON TON TON 0 TON 0 TON 750
TON TON
1 Assy. 2700 2526 2525 2504 2503 2502 2501 3300 3309 8011
1 Body Only 2701 2528 2527 2508 2507 2506 2505 3302 3309 8011
Drive Hole
4 2713 2713 2534 2535 2534 2713
Bushing
Hinge Pin,
1 2711 8047
Removable
Hinge Pin,
1 2709 8046
Stationary
Hinge Pin
1 2715 2715
Retainer
2 Lock 2541 2541 2543 2514 2514 2514 2541
2 Eccentric Pin 2542 2542 2544 2515 2515 2515 2542
Retaining Pin, 50106 50106- 50106- 50106
2 50104-10 50104-10 50104-10
Lock -24 24 20 -24
Bit Breaker
1 2537 2537 2536 2537 2536 8022
Plate
1 Lifting Sling 2712 2511 2511 2511 2511 2511 2511 2511 2511 8023
INSERT BOWLS - 500 TON, 4 TAPER
API Bowl, 8
2546XT251 2545XT250 2545XT250 2545XT250
1 Set 5/8” & 2706 2530 2529 8018
0 9 9 9
Smaller Pipe
1 Set No. 32 Bowl, 2707 2532 2531 2547XT 8019
10 3/4” & 9
5/8” Casing
No. 31 Bowl,
1 Set 13 3/8” & 11 2708 2533 2548XT 8020
3/4” Casing
XT - Indicates Extended Taper Bowls available as options. See page 16 for 49 1/2” HMB Bowls and Slips detail.
See the Rotary Equipment Data Table for 49 1/2" Bowls and Slips detail.