Beruflich Dokumente
Kultur Dokumente
No: 142
IJM GULF
WORLD TRADE CENTER
DHA ISLAMABAD
METHOD STATEMENT
PAINT
1 of 5
Doc. No: 142
IJM GULF
WORLD TRADE CENTER
DHA ISLAMABAD
1. SCOPE:
The work under this method statement consists of furnishing all the surfaces in any
floor and at any height in connection with surface preparation, mixing, painting
concrete works i.e. walls, ceilings and all such surfaces, architectural textured coating,
as shown on drawings and/or directed by the Engineer.
2. Submittals:
2. The Engineer will furnish a schedule of colour/tecture of each area and surface.
All colours shall be mixed in accordance with the manufacturer’s selection.
3. Materials:
All material shall be delivered to site in their original unbroken containers or packages
& shall bear the manufacturer’s name, label, brand & formula & will be mixed and
applied in accordance with his directions.
Paints/coatings shall be delivered to the site in sealed containers, which plainly shows
the type of paint, colour (formula or specifications number) batch number, texture,
quantity, date of manufacture, name of manufacturer and instructions for use.
Pigmented paints shall be supplied in containers not larger than 20 litres. All materials
shall be stored under cover in a clean storage space, which should be accessible at
all the time to the Engineer. If storage is allowed inside the building, floors shall be
kept clean and free from spillage.
5. Execution:
Surface Preparation:
1. All oil, grease, dirt, dust, loose mill scale and any other foreign substance shall
be removed from the substrate surface to be painted/coated, polished and
white washed by the use of a solvent and clean wiping material. Following the
solvent cleaning, the surface shall be cleaned by scrapping, chipping, blasting,
wire brushing or other effective means as approved by the Engineer.
2. In the event the surface becomes otherwise contaminated in the interval
between cleaning and painting/coating, re-cleaning will be done by the
contractor at no additional cost.
3. Surfaces of stainless steel, aluminum bronze and machined surfaces adjacent
to metal work being cleaned or painted shall be protected by effective masking
or other suitable means, during the cleaning and painting operations.
4. All the surfaces to be painted/coated with approved quality paint/coat shall be
free from dust, dirt, fungus, lichen, algae etc. Oil paint, varnish and lime wash
should always be removed by scraping and washing.
5. All surfaces to be bitumen painted shall be thoroughly cleaned of any
accretion, dust, dirt etc. by scraping, wire-brushing or as directed by the
3 of 5
Doc. No: 142
Engineer. The surface shall be primed with a coat of asphalt oil used at the rate
of not less than 1 gallon per 100 square foot of area.
No work in this section shall be allowed until all surfaces or conditions have been
inspected and approved by the Engineer.
Application:
1. All paints and coating materials shall be in a thoroughly mixed condition at the
time of application. All work shall be done in a workman like manner leaving the
finished surface free from drips, ridges, waves, lapse and brush marks. All paint
shall be applied under dry and dust free conditions unless approved the
Engineer paint shall not be applied when the temperature of the metal or the
surrounding air is below 7 degree centigrade. Surface shall be free from
moisture at the time of painting.
All primary paint shall be applied by brushing. The first coat of paint shall be
applied immediately after cleaning. When paint is applied by spraying, suitable
measures shall be taken to prevent segregation of the paint in the container
during painting operation.
Effective means shall be adopted for the removing all free oil and moisture from
the air supply lines of the spraying equipment. Each coat of paint shall be
allowed to dry or harden thoroughly before the succeeding coat is applied.
Coats of Weather Shield Coat paint and textured coating shall be applied in
accordance with manufacturer’s instructions or as directed by the Engineer.
For painting only as much as much material should be mixed as can be used
up in one hour. Over-thinning will not be permitted. After the first coat the
surface will be soaked evenly four or five times and the second coat shall be
applied after leaving for at least overnight.
2. Where shown on drawings all the exterior finishes shall be painted/coated with
Weather Shield/weather coat paint or texture coated in approved
colour/textures as per the manufacturer’s specifications. The number of coats
shall be shown on the drawings or as directed by the Engineer.
3. All wooden doors shall be painted with the approved synthetic enamel paint or
lacquer polished as per manufacturer’s recommendation and instructions or
after approval of the Engineer.
4. Plastic emulsion paint, vinyl emulsion paint or matt enamel paint of the
approved make and shade shall be applied to surfaces as shown on drawings
as per manufacturer’s instructions. The number of coats shall be as indicated
on drawings or as directed by the Engineer.
4 of 5
Doc. No: 142
Job Conditions:
6. Safety Measures:
(a) All the workers will be instructed to wear safety shoes or water boots, safety
helmets, safety gloves and proper dress during paint, in order to avoid any mishaps.
(b) Safe scaffolding shall be made available to work on height having green tag by
safety department.
(c) In case of any mishap, first-aid facility and a vehicle will be available at site at all
times during concreting in order to provide proper treatment to the workers.
5 of 5