Beruflich Dokumente
Kultur Dokumente
AHGM SERIES
CONTENTS
1. INTRODUCTION
2. SPECIFICATIONS
2.1 SYSTEM BLOCK DIAGRAM
2.2 PHYSICAL LAYOUT OF ELECTRICAL CONNECTION
2.3 GENERAL SPECIFICATIONS
2.4 INTERNAL SETTINGS AND CALIBRATION METHODS
3. TROUBLE SHOOTING
3.1 TROUBLE SHOOTING LOOP
3.2 PARTS AND COMPONENTS TROUBLE SHOOTING
4. ELECTRICAL CIRCUITRY
4.1 SCHEMATICS
4.2 PCB LAYOUT
5. BILL OF MATERIAL
6. APPENDIX
1
1. INTRODUCTION
The AHGM series is designed and programmed according to the OIML -76
R
Class III requirements.
Should a load cell has been replaced, make sure that the protection
devices are properly set.
2
2. SPECIFICATION
2.1 SYSTEM BLOCK DIAGRAM
LCD
E+ CPU
LOAD E- A/D UNIT with ROM
CELL S+
S-
POWER SUPPLY: KEYBOARD
AC ADAPTOR (5 KEYS)
(9V/500mA)
RECHARGEABLE
BATTERY (6V 4Ah)
Description:
When a mass is placed on the platform, the load of the article is applied
to the load cell inside it.
The resistance to the excitation current in the strain gauge will then
changed and the analog output signal varies.
It is amplified and digitized continuously by the A/D converter into
a digital signal. Subsequently, the resulting count is processed and
managed by the CPU. The CPU refers to the instructions from the keyboard,
and then conveys the output data to LCD driver, which formats the data
into readout on the display panels.
3
2.2 PHYSICAL LAYOUT OF ELECTRICAL CONNECTION
LCD CN1
AGM-40-X
POWER BOARD
OPTIONAL REAR PISPLAY BOARD GM-20-X
DC JACK
LOAD CELL
RS-232 BOARD
RECHARGEABLE RS232C-1B1
BATTERY
6V 4Ah
MAIN BOARD
AGM-10-X J5
LCD J3
J4 E+
E-
S+
S- J2
MEMBRANE K/B
4
2.3 GENERAL SPECIFICATION
5
2.3.2 Dimension:
6
2.4 CALIBRATION METHODS
AUTO CALIBRATION
a. Turn scale off
b. Press and hold MODE, then press ON/ZERO
c. Scale displays CAL._1
d. Press MODE for YES and scale will self calibrate zero point
before proceed to the first point calibration
e. Load the mass according to the display, normally the first
point is 1/3 of the full capacity
f. Press MODE when display is flashing
g. Scale displays CAL._2
h. Press MODE for YES or ON/ZERO to exit
i. Load the mass according to the display, normally the second
point is the full capacity
j. Press MODE when display is flashing to complete the calibration
procedures
7
3. TROUBLE SHOOTING
3.1 TROUBLE SHOOTING LOOP
POWER ON
GHOST UNSTABLE
PROPER READOUT?
NORMAL OPERATION
8
3.2 PARTS AND COMPONENTS TROUBLE SHOOTING
3.2.1 Power Supply Checking
3.2.1.1 Relevant parts:
Power Board (GM-20-X)
Q1 (C1061)
Q2 (C945)
R1 (1.2R 1/2W)
ZD1(ZENER 8.2V)
DC JACK
BATTERY(6V 4Ah)
Q1 R1
C1061 1/2W 1.2R
R2 Q2
J1 1/2W 100R C945
SCD-22 B1
W04 1A
MB
D1 SIP4 BAT
ZD1 1N4148 R3 1 2PIN
2 1
8.2V 15K 3 2
4
R5
1/4W 220R Q3
A733
L1
L-59EGW
R4
470R
9
Description:
1) Power source: Rechargeable Battery 6V/4Ah or AC adaptor(9V,
500mA)
4) Auto-off:
If the scale is set with 4_oFF or even under LO-BAT situation,
after fixed time interval, CPU will release a low potential signal
to draw down Q2, then Q1 cuts off, the scale will be shut down
immediately.
10
3.2.3.2 Check whether LCD is broken.
3.2.4.1 Check that all pins are seated properly into the socket.
When no error is found with the above checking procedures, the trouble
can be caused on the loadcell or the PCB itself. Replace a new one
could be better to identify the defective.
In this way, the readout of weight would be varied because of the output
voltage of loadcell and different span value, so re -calibration is
required after this replacement.
11
4. ELECTRICAL CIRCUITRY
4.1 SCHEMATICS
12
13
14
15
16
1 2 3 4
D D
Q1 R1
C1061 1/2W 1.2R
R2 Q2
J1 1/2W 100R C945
SCD-22 B1
W04 1A
MB
D1 SIP4 BAT
C
ZD1 1N4148 R3 1 2PIN C
8.2V 2 1
15K 3 2
BATTERY 6V 10AH
4
R5
1/4W 220R Q3
A733
L1
L-59EGW
R4
470R
B B
Title
A A
G-SERIES CHARGING BOARD
Size Number Revision
A4 GM-20-2
Date: 1-Dec-2000 Sheet 1of 1
File: E:\GM20B.S01.sch Drawn By: BEN LEE
1 2 3 4
4.2 PCB LAYOUT
17
AGM-40-1 TOP LAYER
18
5. BILL OF MATERIAL
STRUCTURE
Parts No. Description Specification Qty Remark__
E1AGM000010 P.C.B. KIT AGM-10-1 MAIN BOARD 1
E1AGM001000 P.C.B. KIT AGM-40-1 REAR BOARD 1
E1GSP010000 P.C.B. KIT GM-20-1 POWER BOARD 1
A0002030*** LOAD CELL C2G1 1
AHGM-1500 C2G1-3kg
AHGM-3000 C2G1-6kg
AHGM-6000 C2G1-10kg
AHGM-15K C2G1-20kg
AHGM-30K C2G1-35kg
19
AGM-10-X MAINBOARD
E0AGM000010 P.C.B. AGM-10-1 1
20
A1500000004 BUZZER OBO-15210 1 BZ1
A/D SECTION
A0203077050 I.C. AD7705AN 1 U3
21
BACK LIGHT OPTION
A1400000009 BACK LIGHT 82*40mm 1 EL1
RS232 OPTION
E1GEC100000 P.C.B. KIT RS232C-1B1 RS232 BOARD 1
22
6. APPENDIX
23
ITEM PART NAME DESCRIPTION QTY
1 PLASTIC CABINET, UPPER GM SERIES(WHITE) 1
2 PLASTIC CABINET, UNDER GSP SERIES (GRAY) 1
3 ALUMINUM L/C SUPPORT(UPPER) GSP SERIES (C2X1 L/C) 1
4 ALUMINUM L/C SUPPORT(UNDER) GSP SERIES (C2X1 L/C) 1
5 PLASTIC PLATTER GSP SERIES 1
6 ADJUSTABLE FEET M SERIES 4
7 BATTERY CAP EM SERIES(GRAY) 1
8 OVERLAY AHGM SERIES 1
9 REAR PANEL AHGM SERIES, REAR DISPLAY 1
10 LOAD CELL C2G1 1
AHGM-1500 C2G1-3kg
AHGM-3000 C2G1-6kg
AHGM-6000 C2G1-10kg
AHGM-15K C2G1-20kg
AHGM-30K C2G1-35kg
11 RUBBER PAD CFR-190603 (GSP SERIES) 4
12 PANEL PC G SERIES, 98*45.5*0.8mm 1
13 RECHARGEABLE BATTERY GP4-6 6V 4AH 1
14 S/S PLATTER GP,NEC,NEP SERIES 1
15 P.C.B. KIT AGM-10-1 MAIN BOARD 1
16 P.C.B. KIT AGM-40-1 REAR BOARD 1
17 P.C.B. KIT GM-20-1 POWER BOARD 1
18 FLAT CABLE 24PIN 35CM 1
19 WIRE ARRAY 4PIN 40cm, SINGLE HOUSING 1
20 BUBBLE LEVEL D14 (Dia. 14mm) 1
21 MEMBRANE K/B XM SERIES(OIML) 1
24
APPRO VED NO. REV.
25