Sie sind auf Seite 1von 5

Roll#_________________________

Mehran University of Engineering & Technology Jamshoro Sindh


DEPARTMENT OF MECHATRONICS ENGINEERING
Strength of Material
Practical Test-I
Time Allotted: 15 Minutes______________ Date: 29-01-2018_ _Maximum Marks:05
1 The ratio of the difference of final & initial lengths to the original length is measure
of______________
(a) %Elongation ((b) % Reduction in Area (c) Stability (d) A & B
2 Resistance of material against any external force is known as :
(a) Stiffness ((b) Malleability (c) Strength (d) Hardness
3 Resistance developed by surface of any material is known as :
(a) Strength ((b) Hardness (c) Stiffness (d) Creep
4 Steel ball is used as Intender in which of the following test?
(a) Brinell hardness test (b) Rockwell harness test (c) Vickers hardness test (d) A.o.T
5 The property of a material that resists penetration or indentation by means of abrasion
or scratching is known as
(a) Strength (b) Hardness (c) Toughness (d) Brittleness
6 During hardness test the indenter is usually a
(a) Ball (b) Pyramid (c) Cone (d) All of these
7 Tensile strength of a mild steel specimen can be roughly predicted from following
hardness test
(a) Brinell. (b)Rockwell (c) Vicker (d) none of the above.
8 Intender used in brinell hardness testing machine is
(a) 25 mm dia (b) 15 mm dia (c) 10 mm dia (d) none of the above
9 What is the point at which the sample will return to its original size called?
(a) Rupture Point (b) Elastic Limit (c) Yield Point (d) none of the above
10 Which of the following pair has same dimension?
(a) Stress, Strain (b) Area, Moment of Inertia
(c) %Elongation, %Reduction (d)Shear Modulus, Elastic Modulus
Roll#_________________________

Mehran University of Engineering & Technology Jamshoro Sindh


DEPARTMENT OF MECHANICAL ENGINEERING
Strength of Material
Practical Test-I
Section (A)
Time Allotted: 15 Minutes_________ Date: 25-01-2018_ ___ _Maximum Marks:05
1 The ratio of the difference of final & initial lengths to the original length is measure
of______________
(a) %Elongation ((b) % Reduction in Area (c) Stability (d) A & B
2 Resistance of material against any local force is known as :
(a) Stiffness ((b) Malleability (c) Strength (d) Hardness
3 Resistance developed by surface of any material is known as :
(a) Strength ((b) Hardness (c) Stiffness (d) Creep
4 When a body is subjected to two equal and opposite pulls, as a result of which the body
tends to extend its length, the stress and strain induced is
(a) Compressive stress, tensile strain (b) Tensile stress, tensile strain
(C) Tensile stress, compressive strain (D) compressive stress, compressive strain
5 The property of a material that resists penetration or indentation by means of abrasion
or scratching is known as
(a) Strength (b) Hardness (c) Toughness (d) Brittleness
6 The property of material that determines its behavior under applied loads is called
(a) Elasticity (b) Plasticity (c) Mechanical Property (d) Hardness
7 Tensile strength of a mild steel specimen can be roughly predicted from following
hardness test
(a) Brinell. (b)Rockwell (c) Vicker (d) none of the above.
8 “15BHN150/2500” from this given hardness value what will be tensile strength?
(a) 51.75 (b) 86.25 (c) 5.175 (d) 517.5
9 What is the point at which the sample will return to its original size called?
(a) Rupture Point (b) Elastic Limit (c) Yield Point (d) none of the above
10 The ratio of the difference of final & initial lengths to the original length is measure
of______________
(a) %Elongation ((b) % Reduction in Area (c) Stability (d) A & B
Roll#_________________________
Mehran University of Engineering & Technology Jamshoro Sindh
DEPARTMENT OF MECHANICAL ENGINEERING
Strength of Material
Practical Test-I
Section (B)
Time Allotted: 15 Minutes___________ Date: 30-01-2018_ _______ _Maximum Marks:05
1 Angle of twist varies __________________with polar moment of inertia
(a) Directly ((b) Inversely (c) not affected
2 By applying the tensile test on ductile material, neck occurs at_______________
(a) 45o ((b) 35o (c) 40o (d)14o
3 Resistance developed by surface of any material is known as :
(a) Strength ((b) Hardness (c) Stiffness (d) Creep
4 When a body is subjected to two equal and opposite pulls, as a result of which the body
tends to extend its length, the stress and strain induced is
(a) Compressive stress, tensile strain (b) Tensile stress, tensile strain
(C) Tensile stress, compressive strain (D) compressive stress, compressive strain
5 The property of a material that resists penetration or indentation by means of abrasion
or scratching is known as
(a) Strength (b) Hardness (c) Toughness (d) Brittleness
6 The property of material that determines its behavior under applied loads is called
(a) Elasticity (b) Plasticity (c) Mechanical Property (d) Hardness
7 Which of the following is the hardest material?
(a) Brass (b) Aluminum (c) Mild Steel (d) none of the above.
8 Polar Moment of Inertia defines?
(a) Size of Specimen (b)Shape of Specimen (c)Both (d) Material Distribution
9 What is the point at which the sample will return to its original size called?
(a) Rupture Point (b) Elastic Limit (c) Yield Point (d) none of the above
10 Which of the following pair has same dimension?
(a) Stress, Strain (b) Area, Moment of Inertia
(c) %Elongation, %Reduction (d)Shear Modulus, Elastic Modulus
Roll#_________________________
Mehran University of Engineering & Technology Jamshoro Sindh
DEPARTMENT OF MECHANICAL ENGINEERING
Strength of Material
Practical Test-I
Section (C)
Time Allotted: 15 Minutes_________ Date: 26-01-2018_ _Maximum Marks:05
1 If a material is tested for hardness, under the pressure of 1500 Pa, for 15 seconds its BHN
value is 200. Chose the correct code for this test.
(a) 1500BHN200/15 ((b) 15BHN1500/200 (c) 200BHN15/1500 (d) 15BHN200/1500
2 By applying the tensile test on ductile material, neck occurs at_______________
(a) 45o ((b) 35o (c) 40o (d)14o
3 For a given Length and angle of twist, Which diameter is suitable for a turbine shaft,
when it is subjected to maximum torque of a load of 100 Nm
(a) 10 mm ((b) 15mm (c) 20mm (d) 25mm.
4 Modulus of Rigidity is the ratio of:
(a) Compressive stress and tensile strain (b) Tensile stress and tensile strain
(C) Shear strain and Shear Stress (D) Shear stress, Shear strain
5 The property of a material that resists penetration or indentation by means of abrasion
or scratching is known as
(a) Strength (b) Hardness (c) Toughness (d) Brittleness
6 The property of material that determines its behavior under applied loads is called
(a) Elasticity (b) Plasticity (c) Mechanical Property (d) Hardness
7 Which of the following is the hardest material?
(a) Brass (b) Aluminum (c) Mild Steel (d) none of the above.
8 Polar Moment of Inertia defines?
(a) Size of Specimen (b)Shape of Specimen (c)Both (d) Material Distribution
9 The Ductility of material ____________with the decrease in percentage elongation of a
specimen under the tensile load
(a) Decrease. (b) Increases (c) remains unchanged
10 Write the formula for:
(a) Angle of Twist=

(b) Engineering Stress=

Das könnte Ihnen auch gefallen