Beruflich Dokumente
Kultur Dokumente
Prepared by:
Samsung
Course Name: SCFT Procedure
Course Objective Who should attend
This module will enable participants to Field engineers
understand how to conduct SCFT
Drive test Engineers
This module will also help to understand
the Work Flow Management for
RF Leads / Area Managers
SCFT(WAS-SCFT)using online portal
SITFORGE.
Session -1 Session -2
• SCFT Tests •SCFT -S4 Mini/ troubleshooting Guide
Lunch break
• SCFT Tool • Important Notes
(XCAL mobile - software version • Hands on exercises
Day 1 Operational Process
• SCFT WAS Workflow
•SCFT Siteforge module
Document History
Need to sign attendance sheet at the start and end of each day
Your valuable feedback will be taken at the end to enhance training experience
Introduction to SCFT
What is SCFT
Overview of SCFT Process
SCFT Workflow
Roles & Responsibilities
SCFT Requirements
Lead time
Tools
Drive Test
SCFT Stationary test
SCFT Moving test
Checklist during drive
Post SCFT Drive
Verification of
Availability and performance of
desired services
Physical configuration of the eNodeB
for each sector
Correct installation and configuration
((( ((( of the eNodeB
No Adjust Antenna
Pass Parameter and
SOLPAR
etc.
Scope Yes
Drive Test
SOLPAR PM
DT Engineer
DT Engineer
Roles & Responsibilities – SOLPAR Project Manager
Daily tracking of progress status
Extend support to circle SCFT Team for their minor & critical issues.
Prepare the RF Database and data backup of all drive related tests
( including any snaps) and provide to Samsung
Roles & Responsibilities – SOLPAR DT Engineer
Perform Field Test: DT testing and data collection during -
SCFT/Cluster Optimization
Rigger will make corrections on site and inform Drive Test Engineer
Drive Test Engineer will create the drive routes & configure the
Smart S4 mini as per defined test scenarios
Drive Test Engineer will save the log file. In case of handoff fail, bad
RSRP, call drop etc., inform respective teams immediately
Summary
Strictly follow all the health & safety guidelines
SCFT team consists of an DT engineer, Rigger and Car driver with well-defined
roles and responsibilities for all
Quiz
You find that the antenna azimuth is incorrect. You will _________
• Correct it, log and report the error and then proceed with drive test
• Proceed with the drive test and report it later
• Cancel the drive test
Maintain performance check records with history as per the attached sheet
Appendex-Smart DM
performance management.xls
Preparations for SCFT
Preparations for SCFT
S4 mini mobiles should be ready with
Get Site Access Confirmation from SOLAPR fully charged condition along with
PM mobile charger, Mobile holder,
Inverter, 4 points spike guard
7)
SOLPAR Engineer will collect the TSSR Report
If wall mount antenna or
& Cell ref file from SOLPAR PM who in-turn
Highway/Flyover mount site, then
shall collect the TSSR report & Cell ref file
accordingly arrange extra wall
from Samsung circle RF Lead
mount rigger with rope etc and
hydraulic vehicle (by informing
SOLPAR PM and Samsung area
Check other tools readiness like magnetic manager) in advance respectively
compass, tilt meter and laser meter Important:
no Test can be carried out if the handset. Is less
than 10% charged
Preparations for SCFT…
eNB Parameter
TSSR/Cellref
Verification Drive Route Checklist
Review
from LSM-R
Preparations for SCFT…
Technical Site Survey Report (TSSR)/ Cell ref info
Ensure that the site is verified as per TSSR/Cell ref file, any deviation need to
report Samsung immediately
Attached annexure-1 for the same to be filled up and handed over to SOLPAR
PM, who later sends it over to Samsung RF manager.
In case of any deviation in the same it needs to be corrected in cell ref file/field
before proceeding for the drive.
If it’s a RP1 site and On field data does not match with cell ref file then no need
to rectify physical parameter at field but need to correct only cell ref file.
Preparations for SCFT…
Technical Site Survey Report (TSSR/Cell ref)
• Satellite map: Pre analysis for service area. Google earth snapshots of actual locations and
populated areas
• Vector Map: Refer during drive test.
Satellite &
Vector maps
eNB Parameter
TSSR /Cell
Verification Drive Route Checklist
refReview
from LSM-R
Preparations for SCFT…
eNB Parameter Verification from LSM-R
Configuration
MIMO Type Parameters SON, ANR
(2x2, 4x2)
features
from LSM-R
MIMO
Access class
Mode
barred for
(TM3/TM4)
other UEs
from LSM-R
Preparations for SCFT…
eNB Parameter Verification from LSM-R
• Site down
• High drop Rate
Service Affecting • Low Tx Power
Alarms • GPS Alarm
VSWR values
• Tx Power is transmitted power from eNB station, measured Watts or dBm. Typical
value is 10W or 40dBm
Tx Power
Preparations for SCFT…
eNB Parameter Verification from LSM-R
eNB Parameter
TSSR Review Verification Drive Route Checklist
from LSM-R
Drive Route Basics
Minor
Major Road
Road
eNB Parameter
TSSR Review Verification Drive Route Checklist
from LSM-R
Check list for DT Engineer
Site access confirmation to be done in advance via Samsung area manager and
DT should get in touch directly with the person having key to the site.
Confirmation from Samsung area manager for eNB Commissioning (ATP–11B)
to be passed without any punch points before going for SCFT.
Two S4 mini mobile phones fully charged and mobile chargers should be ready.
DT and rigger ID proof and Reliance representative authorization letter
(multiple photo copies) of the DT and rigger having permission from RJIL to
conduct DT on behalf of RJIL (letter should not be site specific rather it should
be in general so that the same can be used in all sites). This letter to taken
from SOLPAR project manager who will get this letter from Samsung Area
Manager.
Site TSSR/Cell ref to be checked in advance, orientation and lat/long of site and
antenna location type (in case of wall mount antenna, extra riggers to be
arranged one day in advance, prior to the test)
Check list for DT Engineer…
Site access confirmation to be done in advance via Samsung area manager and
DT engineer should get in touch directly with the site owner
Magnetic compass to measure azimuth
Laser meter or measuring tape to measure antenna height
Tilt meter to measure the antenna tilt.
S4 mini should have adequate space to store snaps taken by mobile in case of
drive getting obstructed.
Car with Cigarette lighter Inverter, spike guard and mobile holder for the
mobile to stick on dashboard over the holder
Hydraulic vehicle in case of highway/road/Flyover mounted sites, request
should go over to SOLPAR PM and Samsung area manager a day in advance
who will gets in touch with Reliance area manager for the same.
Fill up the attached Annexure (Total 3) as in check list and handed over to
SOLPAR PM, who sends it over to Samsung RF manager.
Handset should be fully charged else no Test can be carried out by the handset
Check list for Rigger
FTP server
Connectivity
No
OK
Yes
No
OK
Yes
Start testing
Summary
Perform regular testing of drive-test UE’s
Preparations for SCFT consist of TSSR review, eNB parameter verification from
LSM-R, availability of drive route and checklists. Before proceeding to the site
make sure you have these
TSSR gives details about eNB physical parameters such as antenna height,
azimuth, tilt, pictures of obstruction, site drawings and map views
1. Stationary Test
a. Attach
b. VOLTE Short call
2. Moving Test
a. FTP -DL
b. FTP -UL
Stationary Test ( Alpha Sector)
Stationary Test Procedure:
Drive test engineer will start the drive test activity with stationary test.
Move over to Alpha sector and perform following activities
Latch on alpha sector PCI and RSRP, it should have a stable dominant RSRP
level from serving cell, and neighbor cells should not be dominant.
Check GPS status and select destination value of co-ordinates from map
window.
Assign “Stationary-1” call setting with Cycle information & site details, (CYCLE
should remain the same until the complete SCFT test (STATIONARY & MOVING)
ends), if you have to restart the test cause of any issue then issue new and
different cycle number, but it should be same for stationary and moving test
(ideally it should be incremented by 1, every time you repeat the test on same
site), cycle is a reference for naming the log files.
Stationary Test( Alpha Sector)…
Perform under mentioned test by pressing “AUTO CALL” over the s4 mini
phone.
. Stationary Test
a. Attach
b. VOLTE Short call
Drive test engineer now moves over towards Beta sector and
performs the following activities during stationary test:
Check PCI
Assign “Stationary-2” call setting with cycle information & site details
Perform under mentioned test by pressing “AUTO CALL” over s4 mini
handset.
a. Attach
b. VOLTE Short call
Drive test engineer shall move over towards Gamma sector and perform the
following activities during the stationary test
Check PCI and latch to it.
Assign “Stationary-3” call setting with cycle information & site details
Perform under mentioned test by pressing “AUTO CALL” over s4 mini
handset.
a. Attach
b. VOLTE Short call
At the end of “Auto call” presses status as “Completed”.
Press “Auto DRM/DRX Upload “button which is popped up & wait for
upload to finish
Moving Test
After completion of “Stationary” test now the DT has to go for the “Moving test”, drive test
engineer will use two S4 mini handsets.
There will be two different tests that shall be performed on these handsets.
One handset for DTDL
One handset for DTUL
“Moving test” call logging should start by performing a walk test around the site in clockwise and
anticlockwise direction for checking the inter-sector handover within the SCFT site and checking
the correct PCI as seen in cell reference file.
Drive test engineer will carry out the remaining part of moving test while in car in a continuous
log.
Keep checking the PCI of serving cell so as to confirm handover between neighbors of same site.
Move from Alpha sector to Beta sector to check handover between them.
Move from Beta sector to Gamma sector to check handover between them.
Move from Gamma sector to Alpha sector to check handover between them.
Move from Alpha sector to Gamma sector to check handover between them.
Move from Gamma sector to Beta sector to check handover between them.
Move from Beta sector to Alpha sector to check handover between them.
Make “Coverage footprint” of each sector in all possible drive routes based on Morphology based RSRP
Levels.
After finishing the clockwise / anti-clockwise routes, You must run through DTR (Drive test route) provided
to you by Samsung RF lead
NOTE : Samsung RF lead has to provide DTR based on best server plot , as per example attached below. Or
Alternately Samsung RF lead must follow procedures provided by National RF Optimization team to prepare
DTR , This is Mandatory
Moving Test…
Important: If handovers are not happening between neighbor cells then stop the drive
and call up LSMR engineer for handover definition or any alarms related to the same,
and resume the drive, post the resolution of the same.
If any Attach fail, /Access fail, Handover fail, Sector swap are observed during
drive test then call should be immediately stopped and LSMR engineer should
be contacted for any running alarm. Later fresh drive for the same should be
done post rectification.
During drive test and eNB physical verification if any physical obstruction due
to which drive couldn’t be done on that road then SOLPAR DT engineer needs
to take the snapshot and pass it over to Solpar PM.
If SOLPAR engineer can’t drive around in the clockwise or anticlockwise
direction then he has to mention the reason against the same along with a
snapshot proof. Also if for the stationary test, SOLPAR engineer is unable to go
into the main lobe while still in car, then he must try to walk and go into major
lobe of the sector, if even that is not possible then he should take snaps to
support the same.
The SOLPAR engineer should not wait more than 30 mins (post escalation to
LSMR and self troubleshooting) for any issue resolution at the site. If issue
resolution is taking time, then he should move to the next site.
Post SCFT Drive
All snapshots post SCFT (road and antenna obstructions) should be taken and
sent to SOLPAR Project Manager/ Samsung Area Manager/Circle RF Lead.
Backup of log files in memory card to be taken by the DT (this will required if
any file got corrupted during upload). Same to be handed over to Circle RF
Lead.
Contact LSMR Engineer to lock the site (all three sectors).
Handover the keys back to from where they were taken.
Inform the Solpar PM and Samsung RF lead about completion of the drive test.
Move over to the next site.
SCFT Tool
(XCAL mobile - software version v4.09.139 )
Operational Process
SCFT Tool(XCAL mobile) -Operational Process
Stationary Test:
Please follow below step by step process, in order to conduct SCFT automation
process on XCAL Auto call
Only 1 mobile is used for Stationary test.
The screenshots are only applicable to handset software version v4.09.139
Start Samsung S-4 Mini testing handset.
SCFT Tool Operational Process – Stationary Test
Start “X-Cal Auto” on handset and wait for IP framing Message.
By pressing “Setting” in main window assign under ‘Select type’, “SCFT” and
then under ‘Test type’ “STATION 1” (refers to stationary 1 test) and then under
‘Site’ select “Site name” and select “Cycle number” under ‘Cycle’ and press
“Save”. (CYCLE should remain the same until the complete SCFT test
(STATIONARY & MOVING) ends), if you have to restart the test cause of any
issue then issue new and different cycle number, but it should be same for
stationary and moving test (ideally it should be incremented by 1, every time
you repeat the test on same site), cycle is a reference for the log files.
By pressing “Setting” in main window assign under ‘Select type’, “SCFT”
SCFT Tool Operational Process – Stationary Test(Alpha Sector)…
Under ‘Test type’ “STATION 1” (refers to stationary 1 test) and then under ‘Site’
select “Site name”
SCFT Tool Operational Process – Stationary Test(Alpha Sector)…
At the end of ‘Autocall’ press status as “In Progress” (Msg which is popped up)
Press “OK” for ‘Auto DRM/DRX upload’ prompt which is popped up & wait for
upload to finish.
After the upload is done for Stationary 1 test, it will prompt for “Do you want
to perform Stationary 2”. Now go for stationary 2(Beta sector) test.
SCFT Tool Operational Process – Stationary Test (BETA Sector)
Now move to Beta Sector and latch to Beta sector PCI.
Press “OK” in handset for “Do you want to perform stationary 2” prompt.
Next under ‘Autocall’ press “Start” in main window (other setting remains same
as in Stationary 1) & repeat the procedure as done in “Stationary 1” test from
Auto call “Start” up-till file upload, make sure the Cycle remains the same.
Press “In Progress” after end of auto call in beta sector and then press “Ok” for
“Do you want to upload right now” prompt.
SCFT Tool Operational Process – Stationary Test( Gamma Sector)
Now proceed for Gamma sector, latch to Gamma Sector PCI for “Stationary-3”
test and repeat the process as done in Beta sector.
The difference here being that when the test ends the file upload status should
be selected as “Complete” instead of “In progress ” which was done while in alpha
and beta sectors.
SCFT Tool Operational Process – Moving Test
Under Moving test, follow the under mentioned steps in both handsets as
depicted.( this step is same as done in stationary test)
SCFT Tool Operational Process – Moving Test…
Select “GPS” in both handsets as was done in stationary mode. ( this step is
same as done in stationary test)
In both handsets Press “Setting” in main window and press “Select type” as “SCFT” and then “Test
type” as “Moving” and then under “Site“ select “name of the site” and “Cycle number” and press
“Save”. (CYCLE should remain the same until the complete SCFT test (STATIONARY & MOVING)
ends). if you have to restart the test cause of any issue then issue new and different cycle number,
but it should be same for stationary and moving test (ideally it should be incremented by 1, every
time you repeat the test on same site), cycle is a reference for the log files.
Press “Setting” in main window and press “Select type” as “SCFT” and then “Test type” as
“Moving”
SCFT Tool Operational Process – Moving Test…
Under “Site“ select “name of the site”
Press ”Start” under ‘Autocall ‘ in both handsets. Check the traffic should get
started on both handset .
SCFT Tool Operational Process – Moving Test…
Now do walk test around the site from to confirm inter sector handover from Gama
to Alpha, Alpha to Beta, Beta to Gamma and then reverse from Gamma to Beta,
Beta to Alpha, and Alpha to Gamma & then continue the drive in CAR from Gama to
Alpha, Alpha to Beta, Beta to Gamma and then reverse from Gamma to Beta, Beta
to Alpha, and Alpha to Gamma, once inter sector handover are confirmed
then continue the drive for Coverage footprint of each sector by driving all roads
within the “Best Server Plot” of the site and additional only 1 road drive in each
sector connecting SCFT and Neighbor site beyond Best server plot is to be done
until a handover happens.
Press Auto call “Stop” after completion of device on both handset and Press
"Complete” under ‘select’.
Press “Auto DRM/DRX Upload” button which is popped up in both handset & wait
for respective uploads to finish only then move from the site.
New features added…..logging file size
Logging file size can be configured....
After every test scenario whenever this is prompt to upload Logs upload it
Press “OK” for ‘Auto DRM/DRX upload’ prompt which is popped up & wait for
upload to finish.
This will automatically upload the logs after every test scenario.
Instead of pressing Ok if you choose to cancel or mistakenly press cancel then
you need to upload logs manually as explain next slide
New features added…..log Upload - Manual
Uploading of logs can be two ways : Manual
Observed Issue:
As shown in picture below though we are able to see our network parameters
being received by the S4-Mini handset, the handset is not registering to the LTE
network.
No Network service on Handset…
1) No network service on S4-Mini handset
Root Cause:
As shown in picture below the “Mobile data” or “Data roaming” settings was
unchecked under “Mobile networks” settings.
No VoLTE service status on S4-Mini handset
2) No VoLTE service status on S4-Mini handset
Observed Issue:
As shown in picture below, though we are able to see data services are active, no
VoLTE service is being observed. The internet & FTP session are running fine as
shown. When VoLTE call is made it shows “mobile network not available”.
No VoLTE service status on S4-Mini handset…
2) No VoLTE service status on S4-Mini handset
Root Cause:
Any change to the VoLTE configuration apart from above element, can cause
this type of problem.
XCAL-Mobile Software (Not XCAL-Auto Call) doesn’t start
3) XCAL-Mobile Software (Not XCAL-Auto Call) doesn’t start
Observed Issue:
Root Cause:
This was caused since the “Automatic date & time” was unchecked in “date & time”
settings.
FTP DTUL failed on Handset
4) FTP DTUL failed on Handset
Observed Issue:
Root Cause:
As shown below, the FTP URL in which file is going to be uploaded, does not
change as per FMS server settings. This caused FTP traffic failure on the slave
handset.
This issue could be due to XCAL-Auto Mobile Version mismatch or old version
being used on slave handset as shown, since after upgrading the XCAL
version, the issue got resolved.
Not able to download scenario
5) Not able to download Stationary or Moving scenario.
Observed Issue:
check the FTP server connectivity in your phones, check the IP address, user id
and password and server path as shown below.
Important Notes
Sector Swap Verification
Legend
Throughputs for Moving in Worst condition shouldn’t go below min. as per following table when
RSRP = -108dbm and SINR = 20db
Please note Throughput should be better when RSRP and SINR is better
* Above table is just for reference for worst condition only
Summary
eNB physical check involves checking azimuth (note free range), tilt, antenna
height, tower height
Drive around the site clockwise & anti-clockwise for moving tests
• 4 Mbps
• 20 Mbps
• 40 Mbps
• PCI
• RSRP
• VSWR
• FTP
• VoLTE
• Either
Work Flow Management for SCFT
Introduction to Work Order Assignment Management
Work Order Assignment Management is also known as WAS.
WAS is going to help users in automating the Work Order(WO) flow in a
systematic manner using a portal called SITEFORGE.
Using this portal each level of Management employees will receive and
execute their WO or Task assigned to them.
Helps to trace the network status through online mode.
Provides Visual steps to guide users on progress and upcoming steps.
Improves productivity & complete visibility.
Helps users to monitor Parameter Compliance Index(Planned Vs. Actual).
Helps users to Search/Filter Sites & WO based on various parameters.
Network Lifecycle Management Flow for SCFT
(Work Allocation System)
Work Flow Management for SCFT
Start
Responsibility:
GIS/SIITE FORGE; RFI report submit Trigger from GIS & WO Issued to
Notification: Samsung Circle Head (CH)
Samsung CH
Reject
Samsung
Notification:
Notification:Samsu Samsung CH assigns the WO to respective Optimization Samsung AM,
ng AM, RJIL CTO Samsung Area Manager (AM) engineer. Samsung RF
Lead, Samsung
CH, RJIO CTO.
Notification:
Samsung CH, AM Splits WO into tasks & assigns SCFT task to
SOLPAR PM respective Solpar PM as per the area.
Accept/Reject(i
f SOLFE is
Notification : Samsung SOLPAR PM Assigns of SCFT
Reject
needed to be
Area Manager, Task to SOLPAR field eng involved Accept
Sasmsung RF lead, RJIL Notification:Sams
RF lead, SOLPAR FE RJIL CTO ung AM, Samsung
Validates RF Lead, Samsung
SOLPAR FE Does the SCFT test in accordance CH, RJIO CTO, RJIL
Notification: SCFT report
with SCFT Test Procedure and update the RF lead
Solpar PM,
Samsung RF Lead
siteforge server if any parameter updates are Accept
done for the site.
Task closure in SITEFORGE
Samsung
Optimization All tasks (ATP11A, ATP11B, SCFT &
Notification: team Validates Responsibility: RJIL
EMF) completed, WO closure
Samsung -CH the SCFT Circle CTO / GIS /
report(Accept/Rej System
ect) Notification RJIL
End Circle CTO, GIS
SCFT procedure on Site Forge (WAS)
CH - Login
Circle Head can login by entering his user name & password here
CH – Dashboard, Sites
Click here to
know details of
that particular
site
Siite
summary,RAN,Inv
entory,Trasnport,P
htos,Regulatory &
Documents can
be viewed here
CH – Work Orders , Sign out
Option to Sign
Out
CH has to click here to Assign
or Re-assign WO to AM
AM can login by
entering username &
Password here
AM has
logged in
here
AM can view
dashboard here
AM – Sites
Filters can be
accessed here
Reports can be
downloaded
here by AM
AM – Work Orders
List of Work Orders Filters can
are displayed here be
accessed
here
Click here
to assign
or re-
assign
Samsung
engineer
After
assigning
engineers
from drop
down
Click here
AM – Work Orders….
Click here to see the list
of tasks available
Click here to
assign the task
to SOLPAR PM
SOLPAR PM logs in
by entering User
name & Password
SOLPAR PM has
Sites information logged in
can be accessed
here Filters for
accessing data
SOLPAR PM- Sites
By clicking on
particular site
SOLPM will be able
to see details of
that site
SOLPAR PM- Tasks
select responsible
SOLPAR FE(DT
engineer)from
dropdown
SOLPAR FE(DT Engineer) – Sign In , Sites
SOLPAR FE(DT
Engineer)logs in with his
user name & Password
SOLPAR FE (DT
engineer)has logged in
List of sites to be here
handled can be
viewed here
Filters are available Here
SOLPAR FE(DT Engineer) – Tasks
FE has to
click here to
complete
task
“Perform
SCFT”
Click here to
edit any
parameters
value if DT
has changed
during SCFT
SOLPAR FE(DT Engineer) – Tasks
After Editing
the
parameter
FE has to
save here
SOLPAR FE(DT Engineer) – Tasks…
Parameter
Changes can
be viewed by
clicking here
SOLPAR FE(DT Engineer) – Tasks , Sign out
By clicking
here FE will
be able to
see Reject
reason of
SCFT report
Samsung
Optimizer
logs in here
Samsung
Optimizer views
list of sites
Samsung Optimizer – Sites
When he
clicks on
particular
site he will
be able to
see Site
summary &
Etc.
Samsung Optimizer – Sites…
RAN details are
Inventory
displayed here
details are
displayed here
Site
documents are
displayed here
Site
documents can
be uploaded
here(if any)
Samsung Optimizer – Tasks
List of tasks to
be handled are
displayed here Task status
is displayed
here
Paramet
er
Click here to changes
know the info can
reason for be seen
rejection here
Samsung Optimizer – Sign Out
Samsung
Optimizer
can sign out
here
Accelerating the SCFT
Process change recommendation
The SCFT Process
1. PCI
2. ECGI
Cellref 3. Site Location (Lat/Long)
4. BSP
5. Coverage KPI
6. Polygon name
Report generation
FMS ActixOne SiteForge
1. No report
SCFT Stationary & 2. Blank KPI
Drive Test Data 3. 18 KPI pass/fail
The broad causes for unsuccessful report
1. Actix/Site ForgeIssue
SiteForge 2. Missing mandatory files
Report
download
1. PCI mismatch
1. No report 2. Missing Lat/Long parameters in the uploaded file
2. Blank KPI
3. 18 KPI pass/fail
KPI failure and its causes
2.9%
Handover Handover Fail (No Attempt)
20.4% 20.9%
Coverage Object Met Azimuth Mismatching
16.7%
19.0%
13.5% Coverage Object Met BSP Mismatching
The Drive Route Should be decided on Google Map within BSP boundaries
1. The BSP to be provided to circle RF Leads
2. It should be possible to super-impose the BSP boundaries over Google map
3. The SOLPAR co-ordinator to take print of Google map with BSP boundaries,
indicate the route on the map and provide to drive test team.
4. Drive test team to follow the map, sign-off & submit.
File upload process (PA5)
1. There is a large NO/PARTIAL REPORT issue due to incomplete upload of files.
1. The FMS should generate an SMS for the completion of all files
2. The X-CAL should have RED/GREEN indication for upload of mandatory files
Sector Swap Confirmation process (PA6)
1. There are sites where the CPRI cable is swapped with other sector RRH.
1. Since the KPI is for info only, RJIL should not hold the SCFT.
2. The SOLPAR team should contact circle RF lead if the throughput is lower than
xxMbps, and should not proceed with the SCFT drive.
Stationary Test process (PA8)
1. The Attach & VoLTE KPI failure is high.
1. There will be two attempts for Attach testing in the X-CAL itself, rather than one.
2. QC1 radio bearer should be mandatory for VoLTE call.
3. If the VoLTE is not successful, the SOLPAR should contact circle RF lead, and
should proceed for Drive Tests.
Summary of processes
Make Cellref Provide updated Cellref file & BSP to RF lead every week
File & BSP
Make SCFT
DTR
Provide SCFT DTR (Map & Ant. Info) to SOLPAR team
No
Report Provide Fail Reason
SiteForge Order Rework (Physical para., Station, Handover, Drive Test)
Verify
Yes
SCFT Site
Survey
ActixOne Report Submit
Yes Ant.Para
PA2
Mismatch
FMS
Change Ant. Para No
If missing neighbor, Add - Observe the target PCI change without Call Drop.
※ If the PCI is changed after call drop, then try to HO
neighbor in each sector
again.
- If call drop happened again and again, then DO NOT
EXECUTE SCFT and feedback to Samsung RF Lead
Confirm Neighbor List
immediately.
Handover Test
PA4 Drive Route Process
NOPT Samsung (Circle RF Team) SOLPAR
Cellref Eng. RF Lead Rigger
Drive Test
according to DTR
Drive Test
Stationary Test
(UE Attach/VoLTE call
setup)
Question 2:
Who will assign “perform SCFT” task to DT Engineer?
Answer:
PM(SOLPAR)
Question 3:
Whether Samsung RF head can reject approved SCFT data by Samsung Optimizer?
Answer:
A) Yes
B) No
Thank You