Beruflich Dokumente
Kultur Dokumente
BALL
SCREWS
02
WWW.HIWIN.CZ
BALL
SCREWS
General informations
3/4
Rolled ball screws
5/8
Peeled ball screws
9/14
Ball screws for special requirements
15/16
Bearing housings
17/29
Shaft ends
30/34
Other accessories
35/49
Project planning sheet
50
02 WWW.HIWIN.CZ
INTELLIGENCE IN MOTION
Ball screws
General informations
Accuracy class
Manufacturing method Diameter range Lead range
Max. path deviation v300p over 300 mm
T 5 (0.023 / 300 mm)
Rolled 8 - 63 mm 2.5 - 40 mm
T 7 (0.052 / 300 mm)
P 5 (0.023 / 300 mm)
Peeled 16 - 80 mm 5 - 20 mm
P 7 (0.052 / 300 mm)
P 1 (0.006 / 300 mm)
Ground P 3 (0.012 / 300 mm) 6 - 100 mm 1 - 50 mm
P 5 (0.023 / 300 mm)
Profile
Spindle 1.1213 Cf 53 58 - 62
Nut 1.6523 21 NiCrMo 2 58 - 62
Ball 1.3505 100 Cr 6 62 - 66
1.4 Ball recirculation systems External recirculation type nut with return tubes
HIWIN ballscrews are available with three different recirculation systems.
The external recirculation system comprises the ballscrew shaft, ballscrew nut, steel
balls, ball recirculation system and clamping plate. The balls are placed in the ball
track between the ballscrew shaft and nut. At the end of the nut, they are guided out
of the ball track and back to the start via a return tube; ball circulation is therefore
a closed circuit.
2 / 3
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
The internal single recirculation system comprises the ballscrew shaft, ballscrew nut, Internal
Internalsingle
singlerecirculation
recirculationtype nutnut
type withwith
return capscaps
return
General informations
steel balls and deflecting parts. The balls undertake just one circuit around the shaft.
The circuit is closed by a deflecting part in the ballscrew nut and allows the balls to
return to the start via the rear of the thread. The position of the ball deflection in the
nut gives the internal single recirculation system its name.
The internal single recirculation system comprises the ballscrew shaft, ballscrew nut,
steel balls and deflecting parts. The balls undertake just one circuit around the shaft.
The circuit is closed by a deflecting part in the ballscrew nut and allows the balls to
return to the start via the rear of the thread. The position of the ball deflection in the
nut gives the internal single recirculation system its name.
The third type of return is the endcap recirculation system. It has the same basic Endcap
Endcaprecirculation
recirculationtype nutnut
type with recirculation
with system
recirculation system
principleTheasthird
the type
external return,
of return however,
is the endcapthe balls are system.
recirculation returnedIt via
hasathe
channel in the
same basic
ballscrew nut. The
principle balls
as the perform
external one however,
return, completethecycle
ballsinare
thereturned
ballscrew
via nut. The endcap
a channel in the
return orballscrew
“internalnut.total
Therecirculation” provides
balls perform one goodcycle
complete loading
in thecapacity
ballscrewwith
nut.short track
The endcap
lengthsreturn
and small nut diameters.
or “internal total recirculation” provides good loading capacity with short track
lengths and small nut diameters.
By default, rolled and peeled ballscrews are delivered with slight play. This is suf-
axial load
Fa (or P)
Fa (or P)
By most
ficient for default, rolled and peeled
applications, ballscrews
and has are delivered
the advantage withballscrews
that the slight play.run
Thissmoothly
is sufficient
Fn
for most applications, and
and a low starting torque is required.has the advantage that the ballscrews run smoothly X
and ademands
low starting deviation
If increased aretorque
placedisonrequired.
the positioning accuracy and rigidity, the axial play Fn
If increased demands
can be neutralised by a preload are placed
force P.onForthethis
positioning
purpose,accuracy
differentandmethods
rigidity, are
the axial play Fa (or P)
can
available. be neutralised by a preload force P. For this purpose, different methods are
Sa l Sa l
available. 2
Lead Lead
Preloaded
Preloaded singlesingle
nutsnuts Nut
Preload method withwith
Preload method oversized
oversized ballsballs involves
involves ballswhich
balls whichare
areslightly
slightlylarger
larger than
than the
the
space in the ball track; the ball therefore makes contact at four
space in the ball track; the ball therefore makes contact at four points. points.
Screw Shaft
X preload is generated with an undersized spacer which pulls the nuts together.
The preload is generated by inserting a spacer between the nuts. The O preload Spacer
results from fitting an oversized spacer which pushes the halves of the nut apart.
Preload force Preload force Preload force Preload force
The X preload is generated with an undersized spacer which pulls the nuts together.
INTELLIGENCE IN MOTION
Ball screws
Rolled
2.1 Properties of rolled ball screws
One of the benefits of rolled ballscrews is that feed systems equipped with them have mm are always kept in stock and can be supplied at short notice. They can be supplied
less friction and are quieter than standard threads. with or without end machining. Complete bearing units combined with standardised
shaft ends enable us to supply complete ballscrews.
HIWIN manufactures them using state-of-the-art rolling technologies where the
processes of material selection, rolling, heat treatment, machining and assembly
are very closely coordinated. Rolled ballscrews from HIWIN can be flexibly used in
virtually all areas of industry. Rolled ballscrew shafts with diameters of 8 mm to 63
R 40 05 - FSC - 0586 - X - T_
Nut type
FSI
FSC
RSIT
RSB
SSV
2.3 Product range of rolled ball screws
4 / 5
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
www.hIwIN.Cz
Ball screws
Ball screws
Rolled
Rolled
Simple flanged
2.4. Simple nut acc.
flanged nutDIN part DIN
69051 acc.
FSC/FSI 5 69051 part 5
D2
D2
D2
D g6
D -0,2
-0,3
D1
ds
dk
D3 D3
P D3
L2
L1 B B B
L Hole pattern 0 Hole pattern 1 Hole pattern 2
Accu-
Max. Nut Shaft
racy
P D g6 D1 D2 D3 L L1 L2 L3 S B dk Cdyn [N] C0 [N] axial play weight weight class Accu-
±0,1
ds
patternHole Axial play
[mm] [kg/ks]
Nut
[kg/m] Shaft
racy
Nut type Size P D g6 D1 D2 D3 L L1 L2 L3 S B dk Cdyn [N] C0 [N] max. weight weight
T5
±0.1 pattern class
12x5 11,7 5 24 40 32 4,5 0 33 8 8 4 M3 26 9,9 5500 12000 0,02
[mm] 0,11
[kg]
0,80
[kg/m]
●
R12-05K4-FSCDIN T5
R12-10K3-FSCDIN
R12-05K4-FSCDIN 12x10
12x5 11,8
11.7 10 5 24 24 40 40 32 324,5 4.5 0 043 338 88 84 4 M3 M326 26 9,6 9.95100 550010100 12000 0,02 0.02 0,13 0,77
0.11 ●
0.80 ●
15x5 13,8 5 28 48 38 5,5 1
R15-05K4-FSCDIN
R12-10K3-FSCDIN 12x10 11.8 10 24 40 32 4.5 038 4310 10
8 85 4 M6
M340 2611,8 12600
9.6 510021000 10100 0,04 0.02 0,17 1,07
0.13 -
0.77 ●
R16-05T3-FSIDIN 16x5 15,5 5 28 48 38 5,5 1 40 10 10 5 M6 40 12,9 7320 12470 0,04 0,17 1,26 ●
R15-05K4-FSCDIN 15x5 13.8 5 28 48 38 5.5 1 38 10 10 5 M6 40 11.8 12600 21000 0.04 0.17 1.07 -
R16-10K3-FSCDIN 16x10 14,6 10 28 48 38 5,5 1 45 10 10 5 M6 40 12,5 9100 19300 0,04 0,19 1,17 ●
R16-05T3-FSIDIN 16x5 15.5 5 28 48 38 5.5 1 40 10 10 5 M6 40 12.9 7320 12470 0.04 0.17 1.26 ●
R16-16K3-FSCDIN 16x16 14,4 16 28 48 38 5,5 1 61 12 20 6 M6 40 13,0 9100 19300 0,04 0,30 1,13 ●
R16-10K3-FSCDIN 16x10 14.6 10 28 48 38 5.5 1 45 10 10 5 M6 40 12.5 9100 19300 0.04 0.19 1.17 ●
R16-20K2-FSCDIN 16x20 13,9 20 28 48 38 5,5 1 56 10 10 5 M6 40 11,8 5200 10400 0,04 0,25 1,13 ●
R16-16K3-FSCDIN 16x16 14.4 16 28 48 38 5.5 1 61 12 20 6 M6 40 13.0 9100 19300 0.04 0.30 1.13 ●
R20-05K4-FSCDIN 20x5 19,5 5 36 58 47 6,6 1 40 10 10 5 M6 44 16,9 13400 32740 0,04 0,29 2,07 ●
R16-20K2-FSCDIN 16x20 13.9 20 28 48 38 5.5 1 56 10 10 5 M6 40 11.8 5200 10400 0.04 0.25 1.13 ●
R20-10K3-FSCDIN 20x10 19,3 10 36 58 47 6,6 1 48 10 10 5 M6 44 16,6 10000 23500 0,04 0,32 2,07 ●
R20-05K4-FSCDIN 20x5 19.5 5 36 58 47 6.6 1 40 10 10 5 M6 44 16.9 13400 32740 0.04 0.29 2.07 ●
R20-20K2-FSCDIN 20x20 19,5 20 36 58 47 6,6 1 57 10 10 5 M6 44 17,1 6800 15300 0,04 0,36 2,40 ●
R20-10K3-FSCDIN 20x10 19.3 10 36 58 47 6.6 1 48 10 10 5 M6 44 16.6 10000 23500 0.04 0.32 2.07 ●
R20-20K4-DFSCDIN 20x20 19,5 20 36 58 47 6,6 1 57 10 10 5 M6 44 17,1 12300 30500 0,04 0,36 2,40 ●
R20-20K2-FSCDIN 20x20 19.5 20 36 58 47 6.6 1 57 10 10 5 M6 44 17.1 6800 15300 0.04 0.36 2.40 ●
R25-05K4-FSCDIN 25x5 24,9 5 40 62 51 6,6 1 43 10 12 5 M6 48 22,3 14900 41500 0,04 0,31 3,42 ●
R20-20K4-DFSCDIN 20x20 19.5 20 36 58 47 6.6 1 57 10 10 5 M6 44 17.1 12300 30500 0.04 0.36 2.40 ●
R25-10K4-FSCDIN 25x10 24,4 10 40 62 51 6,6 1 61 10 16 5 M6 48 21,8 15900 404000,04 0,39 3,42 ●
R25-05K4-FSCDIN
R25-25K2-FSCDIN 25x5
25x25 24,7 25 5
24.9 40 40 62 62 51 516,6 6.6 1 170 4310 10
16 125 5 M6 M648 4822,1 22.37500 1490019300
41500 0,04 0.04 0,43 0.31
3,42 3.42
● ●
R25-10K4-FSCDIN
R25-25K4-DFSCDIN 25x10 24,7
25x25 24.4 25 10 40 40 62 62 51 516,6 6.6 1 170 6110 10
16 165 5 M6 M648 4822,1 21.8
13500 1590038200 40400 0,04 0.04 0,43 0.39
3,42 3.42
● ●
R25-25K2-FSCDIN
R32-05K6-FSCDIN 32x5 31,7 5 25 50 40 80 62 65 519,0 6.6
25x25 24.7 1 148 7012 10
12 166 5 M6 M662 4829,1 22.1
23900 750081900 19300 0,04 0.04 0,59 0.43
6,31 3.42
● ●
R25-25K4-DFSCDIN
R32-10K5-FSCDIN 25x25 31,8
32x10 24.7 10 25 50 40 80 62 65 519,0 6.6 1 177 7012 10
16 166 5 M6 M662 4828,6 22.1
31500 1350080100 38200 0,04 0.04 1,02 0.43
6,31 3.42
● ●
R32-05K6-FSCDIN
R32-20K3-FSCDIN 32x5 31,8
32x20 31.7 20 5 50 50 80 80 65 659,0 9.0 1 188 4812 12
16 127 6 M6 M662 6228,6 29.1
17000 2390048500 81900 0,04 0.04 1,02 0.59
6,15 6.31
● ●
R32-10K5-FSCDIN
R32-32K2-FSCDIN 31.8 32 10 50 50 80 80 65 659,0 9.0
32x10 31,9
32x32 1 188 7712 12
12 166 6 M6 M662 6228,7 28.6
11600 3150031800 80100 0,04 0.04 1,20 1.02
6,15 6.31
● ●
R32-20K3-FSCDIN
R32-32K4-DFSCDIN 32x20 31,9
32x32 31.8 32 20 50 50 80 80 65 659,0 9.0 1 188 8812 12
12 166 7 M6 M662 6228,7 28.6
20600 1700062200 48500 0,04 0.04 1,33 1.02
6,15 6.15
● ●
R32-32K2-FSCDIN
R40-05K6-FSCDIN 40x5
32x32 39,4
31.9 5 32 63 50 93 80 78 659,0 9.0 2 150 8814 12
10 127 M8x1
6 M670 6236,8 28.7
25900 11600100600 31800 0,04 0.04 1,10 9,87
1.20 ●
6.15 ●
R32-32K4-DFSCDIN
R40-10K4-FSCDIN 40x10
32x32 37,8
31.9 10 32 63 50 93 80 78 659,0 9.0 2 170 8814 12
16 127 M8x1
6 M670 6232,8 28.7
45000 20600123000 62200 0,04 0.04 1,25 7,70
1.33 ●
6.15 ●
R40-20K3-FSCDIN
R40-05K6-FSCDIN 40x20
40x5 37,8
39.4 20 5 63 63 93 93 78 789,0 9.0 2 288 5014 16 107
14 M8x1
7 M8x170 7032,8 36.8
34850 2590094000 100600 0,07 0.04 1,45 7,70
1.10 ●
9.87 ●
R40-40K2-FSCDIN
R40-10K4-FSCDIN 40x40
40x10 37.8 40 10 63 63 93
37,8 93 78 789,0 9.0 2 102
2 7014 14 167
16 M8x1
7 M8x170 7032.9 23000
32.8 4500058400 123000 0,07 0.04 1,60 8,60
1.25 ●
7.70 ●
R40-40K4-DFSCDIN
R40-20K3-FSCDIN 40x40
40x20 37,8
37.8 40 20 63 63 93 93 78 789,0 9.0 2 102
2 8814 16 167
14 M8x1
7 M8x170 7032,9 41500
32.8 34850115800 94000 0,07 0.07 1,60 8,60
1.45 ●
7.70 ●
R50-05K6-FSCDIN
R40-40K2-FSCDIN 50x5
40x40 37.8 5 40 75 63 110
49,3 93 93 78 11 9.0 2 2 10216
50 10
14 168 M8x1
7 M8x185 7046,8 28300
32.9 23000127200 58400 0,07 0.07 1,30 15,41
1.60 -
8.60 ●
R50-10K6-FSCDIN 50x10 47,9 10 75 110 93 11 2 90 16 16 8 M8x1 85 42,9 74500 250000 0,07 2,20 13,86 -
R40-40K4-DFSCDIN 40x40 37.8 40 63 93 78 9.0 2 102 14 16 7 M8x1 70 32.9 41500 115800 0.07 1.60 8.60 ●
R50-20K5-FSCDIN 50x20 48,0 20 75 110 93 11 2 132 18 25 9 M8x1 85 42,9 62000 208000 0,07 2,50 14,81 -
R50-05K6-FSCDIN 50x5 49.3 5 75 110 93 11 2 50 16 10 8 M8x1 85 46.8 28300 127200 0.07 1.30 15.41 -
R50-40K3-FSCDIN 50x40 50,3 40 75 110 93 11 2 149 18 45 9 M8x1 85 45,0 39000 123000 0,07 3,30 14,81 -
R50-10K6-FSCDIN 50x10 47.9 10 75 110 93 11 2 90 16 16 8 M8x1 85 42.9 74500 250000 0.07 2.20 13.86 -
R50-40K6-DFSCDIN 50x40 50,3 40 75 110 93 11 2 149 18 45 9 M8x1 85 45,0 70300 242600 0,07 3,37 14,81 -
R50-20K5-FSCDIN 50x20 48.0 20 75 110 93 11 2 132 18 25 9 M8x1 85 42.9 62000 208000 0.07 2.50 14.81 -
R63-10T6-FSIDIN 63x10 63,1 10 90 125 108 11 2 120 18 16 9 M8x1 95 58,0 61920 214090 0,07 3,10 22,30 -
R50-40K3-FSCDIN 50x40 50.3 40 75 110 93 11 2 149 18 45 9 M8x1 85 45.0 39000 123000 0.07 3.30 14.81 -
R50-40K6-DFSCDIN 50x40 50.3 40 75 110 93 11 2 149 18 45 9 M8x1 85 45.0 70300 242600 0.07 Dimensions
3.37 in [mm]
14.81 -
R63-10T6-FSIDIN 63x10 63.1 10 90 125 108 11 2 120 18 16 9 M8x1 95 58.0 61920 214090 0.07 3.10 22.30 -
Nuts for rolled ball screws Simple flanged nut Accuracy class T5 on request
Dimensions acc. DIN 69051 part 5 Standard accuracy class T7 Housings for nuts available
Dimensions in [mm]
Nuts with sealings DFSCDIN - double start nut
Nuts for rolled ball screws Simple flanged nut Housings for nuts available
Dimensions acc. DIN 69051 part 5 Standard accuracy class T7 DFSCDIN - double start nut
Nuts with sealings Accuracy class T5 on request
INTELLIGENCE IN MOTION
Ball screws
Rolled
dk
ds
M
D
P
MMmax
max LL
4-Hxt
4-Hxt FF K
K CC
A
A
w
B
dk
ds
W
T
TT
Dyn. Stat.
ds P W F Hxt L B C K T A Mmax dk Capacity
Dyn.[mm] [kg/ks]
C dyn [N] C0 [N]
Stat. [kg/m] Max. Nut Shaft Accu-
R16-05B1-SSV 16x5 16 5 42 16 M5x8 36 32 22 6 21,5 M6 35,0 12,9 6790 12260
0,04 0,26 1,26 ●
Nut type Size ds R20-05B1-SSV
P W F20x5 H20 x 5t 48 17L M6x10
B 35C 35 K22 5
T A Mmax 7450dk 15260
9,0 M6 39,0 16,9
capacity0,04 capacity
0,27 2,07
axial
●
weight weight racy
R25-05B1-SSV 25x5 25 5 60 20 M8x12 35 40 22 7 9,5 M6 45,0 22,3 8450 Cdyn [N]0,04 C0,41
19870 0 [N] 3,42
play [mm]
● [kg] [kg/m] class T5
R16-05B1-SSV 16x5 16 5 42 16
Nut with sealing M5x8 36 32 22 6 21.5 M6 35.0 12.9 6790 12260 Dimensions in0.04
[mm]
0.26 1.26 ●
Standard accuracy class T7
R20-05B1-SSV 20x5 20 5Accuracy
48 class17T5 on request
M6x10 35 35 22 5 9.0 M6 39.0 16.9 7450 15260 0.04 0.27 2.07 ●
R25-05B1-SSV 25x5 25 5 60 20 M8x12 35 40 22 7 9.5 M6 45.0 22.3 8450 19870 0.04 0.41 3.42 ●
6 / 7
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
all screws
olled Ball screws
Rolled
le cylindrical nut with thread RSIT for small diameters
2.7 Simple cylindrical nut with thread RSIT for small diameters
D1
dk
ds
D
P
L1
L Groove for lubricant supply
hout sealing
e side sealing
KuličKové šrouby
HIWIN S.R.O., INFO@HIWIN.CZ, WWW.HIWIN.CZ 16 / 17
INTELLIGENCE IN MOTION
Ball screws
Peeled
In terms of quality, peeled ballscrews from HIWIN fall between rolled and ground ballscrews and can therefore be used for numerous transport or positioning applications.
On request, we are happy to produce a lead measurement report for them. A number of nut shapes are available for peeled ballscrews, as both single and double nuts. Customised
complete ballscrews can be produced with short lead times. Complete bearing units combined with standardised shaft ends minimise the amount of design work involved.
DDB 40 05 R - 0586 - X - P_
Thread
R - right
L - left
8 / 9
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Peeled
Lubrication hole
Lubrication hole
Hole Nut
Nut type ds P D g6 D1 D2 D3 pat- L L1 L2 L3 S B dk Cdyn [N] C0 [N] weight
tern [kg]
Dimensions in [mm]
Lubrication hole
Lubrication 90°
L3
90° 30°
S
Lubrication hole
hole 22,5°
30°
D2
D2
D g6
D -0,2
-0,3
D1
ds
dk
D3 D3
P
L2
L1 B B
L
Hole pattern
Hole pattern 11 Hole pattern
Hole pattern 22
ds <_ds32≤ 32 ds >_ds40> 32
10 / 11
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hIwIN.Cz
www.hiwin.cz
Ball screws
Ball screws
Peeled
Peeled
Simple cylindrical nut ZE
3.6 Simple cylindrical nut ZE
L
L1 L2 L3
B
dk
ds
D
P T
L4
Groove for lubricant supply
L1 L2 L2 L1
B
dk
ds
D
P T
L4
L
Groove for lubricant supply
Dimensions inDimensions
[mm] in [mm]
Nuts for peeled ball screws
Standard
Nuts for peeled preload 7% Cdyn
ball screws
Standard preload 7% Cdyn P5 and P7
Accuracy class
KuličKové šrouby
HIWIN S.R.O., INFO@HIWIN.CZ, WWW.HIWIN.CZ 24 / 25
12 / 13
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Ball screws
Peeled
Peeled
Simple cylindrical nut with thread SE
dk
ds
D
P
L1
L Groove for lubricant supply
KuličKové šrouby
HIWIN S.R.O., INFO@HIWIN.CZ, WWW.HIWIN.CZ 22 / 23
INTELLIGENCE IN MOTION
WWW.HIWIN.CZ
Ball screws
Ball
Ball screws
screws for special requirements
Ball screws for special requirements
4.1 Driven nut unit AME
Driven nut unit AME
D5
D
J
D2
L2 B
M6 lubrication hole L1
L
14
26/ 1/ 27
5
BALL SCREWS
KuličKové šrouby
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
HIWIN S.R.O., INFO@HIWIN.CZ, WWW.HIWIN.CZ
www.hIwIN.Cz
www.hiwin.cz
Ball
Ballscrews
screws
Ball
Ballscrews
screwsfor
forspecial
specialrequirements
requirements
Safety nut SEM
4.2 Safety nut SEM
The safety nut comprises a ball thread unit and safety unit. The safety nut basically
The safety nut comprises a ball thread unit and safety unit. The safety nut basically works
works like a normal ballscrew nut. If the axial play is increased due to wear, ball failure or
like a normal ballscrew nut. If the axial play is increased due to wear, ball failure or ball loss,
ball loss, the thread of the safety unit comes into contact with the ball thread.
Thethenutthread of the
cannot safetybreak
therefore unit comes intonormal
out. The contactfunction
with theofball
the thread. The nut cannot
unit is guaranteed up totherefore
break out. The normal
an axial play of 0.4 mm. function of the unit is guaranteed up to an axial play of 0.4 mm.
Areas of application:
- Lifting equipment Ballscrew unit Safety unit
- Clamping fixtures
- Lifting platforms
- Elevators
90° 90° L3
30°
22,5° S
30°
D2 D2
-0,2
D -0,3
D
D1
dk
ds
D3 D3
P
L2
B B L1
L
Hole pattern 1 Hole pattern 2
ds ≤ 32 ds > 32
Bearing
Bearing housings
housings
5.1 Fixed bearing housing type SFA
Precise bearing housings SFA are recommended for peeled and ground ball screws.
Fixed bearing housing SFA includes:
Steel housing
SFA-06
Angular÷contact
SFA-10ball bearing ZKLF
LockSFA-06
nut ÷ SFA-10
SFA-06 ÷ SFA-10
L2 1
2
45° SC The axis height of the
3 fixed bearing is matched to supported bearing SLA and nut
Fixed bearing housing SFA contains:
H4
housing GFD. The pillow block can be screwed on from above (S1) and below (S2).
Steel housing
S1 The reference edge makes it easier to align the unit. The fixed bearing can be pinned
D1
D
with two tapered pins or cylindrical pins. The end machining suited to the fixed bearing
Lock nut
H1
H3
H5
S3 S2 B2 b B2
L1
L/2 L/2
(L) SC
L L1 L2 L3 H S1
L3 H2 H3 H4 H5 d D D1 b B B1 B2 S2 S3 DIN 912
JS7 H12
10.9
12 SFA-06 62 34 38 50 41 22 13 5 11 9 6 30 19 12The32axis16
height
10,0of the5,3fixedM6
bearing
3,7 is matched to supported
ZKLFA0630.2Z bearing 4SLA
HIR-06 x M3andxnut
12
16 SFA-10 86 52 52 68 58 32 22 7 15 15 10 50 32 20 37 23 8,5 8,4 M10 7,7 ZKLFA1050.2RS HIR-10 4 x M5 x(S2).
housing GFD. The pillow block can be screwed on from above (S1) and below 20
B1
B
The reference edge makes it easier to align the unit. The fixed bearing can be pinned
with two tapered pins or cylindrical pins. The end machining Dimensions
suited to theinfixed
[mm]bearing
is the S2-xx and S3-xx type.
16 / 17
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
BALL
KuličKové SCREWS
šrouby
Ball screws
www.hiwin.cz
Bearing housings
Ball screws
WWW.HiWin.cZ
WWW.HIWIN.CZ
Bearing housings
Ball screws
Ball screws
Bearing housings
SFA-12 ÷ SFA-40
SFA-12 ÷ SFA-40 Bearing housings
SFA-12 ÷ SFA-40
SFA-12 ÷ SFA-40
L2 1
2
45° ZKLF
SC 3
H4
D1
D
d
S1
H
H1
H2
H5
H3
S3 L1 S2 B2 b B2
L/2 L/2
(L) End machining S2-d
L3
B1
B
SC
Ball screw
Bearing unit dimensions L L1 L2 L3 H1
H S1 S1 Lock
Type L L1 L2 L3 H H2 H3
H2 H4 H5 H5d
H3 H4 dD D1D D1
b Bb B1B B1B2 B2 S2 S3 Bearing DIN D
size JS7 JS7 H12 H12 nut
912 10.9
912 1
Ball screw H1 S1 SC
Type
20 20 L SFA-12
L1SFA-12
L2
94 5294L3 5260 H60 77 77 H2 22
64 64
34 34H3227 H4
177 15H5 15
17 12 d12
55 D 25
55
32 32D1 42
25 25b 25
42 B 8,5
8,5 B1 M10
8,4 8,4B2M10
7,7 7,7 S2 S3
ZKLF1255.2RSPE
ZKLF1255.2RSPE HIR-12
HIR-12 3 x M63 xxM6
35 x
size JS7 H12 DIN 912 10.9
25 25 SFA-17 SFA-17
108 108
65 65 66 66 88 8872 72
39 2739 1027 10
19 19
18 18 17 1762 62 25
36 36 4625 2946 10,5
29 10,5
10,5 10,5
M12 M129,7 9,7 ZKLF1762.2RSPE
ZKLF1762.2RSPE HIR-17
HIR-17 3 x M6
SC 3 xxM6
35 x
20 SFA-12 L 52
32 32 94SFA-20L1 112
L2 65L37765
60 112 73H 6473 34 4222H4 710 17 18D1518 49S110,5
SFA-20 92 H292 78
78 H3 42 H5
27 27 10
20
d 20 D1 1220
20 68
b B55 B1
68
42 423249
28 28 25
B2 29 294210,52510,5
10,5 M128.5M12
9,7 8.4
9,7 M10 7.7 3xM6x35
ZKLF2068.2RSPE
ZKLF2068.2RSPE HIR-20
HIR-20 4 x M6
DIN 4 xxM6
40 x
JS7 H12
25 SFA-17
40 40108SFA-30
65
SFA-3066 126
126 828882 84 7284 105
105 39 5027 32
92 92 50 1013
32 19
13
23 211821
23 30 1730
80 62 28
80
52 523653
28 3225 324612,5
53 12,5 2912,6
12,6 10.5M14
M14 9,710.5
9,7 M12 9.7 3xM6x35
ZKLF3080.2RSPE
ZKLF3080.2RSPE HIR-30
HIR-30 6 x M6
912 10.9 6 xxM6
40 x
32 20 SFA-20
50 112
SFA-12 SFA-40
50 65
SFA-40
94 52 14673 146 9282 78
104
60 827710464 125 42
125
34 112
22 6027
112
7 1760 10
32 1332
15 20
13
30
12 21551821
30 32 20
40 40
100
25 68
100
66 25
42 66 42
34 5934 28
59 3449
8,5 348,412,5 12,529
M1012,6 10.5
12,6
7,7 M14 M14 10.5
9,7 M12 9.7 4xM6x40
ZKLF40100.2RSPE
9,7 ZKLF40100.2RSPE
ZKLF1255.2RSPE 3 x M6 x 435x M8 x 50 x
HIR-12 HIR-40 HIR-40 4 x M8
40 25 SFA-30
SFA-17126108 8265 66
84 88 105 72 92 39 50 27 1032 19 1318 23
17 6221 36 3025 80 29 5210,5 2810,5 M12
46 53 9,732 12.5 12.6 M14 9.7
ZKLF1762.2RSPE HIR-17 6xM6x40
3 xDimensions
M6 x 35 in [mm]
Dimensions in [m
50 32 SFA-40
SFA-20 112 65 73 92 78 42 27 1032 20 1318
146 82 104 125 112 60 30
20 6821 42 4028 100 66 34 59 34 12.5 12.6 M14 9.7
49 29 10,5 10,5 M12 9,7 ZKLF2068.2RSPE HIR-20 4 x M6 x 40 4xM8x50
40 SFA-30 126 82 84 105 92 50 32 13 23 21 30 80 52 28 53 32 12,5 12,6 M14 9,7 ZKLF3080.2RSPE Dimensions
HIR-30 6inx[mm]
M6 x 40
50
Technical data of bearing
SFA-40 146 82 104 125 112 60 32 13 30 21 40 100 66 34 59 34 12,5 12,6 M14 9,7 ZKLF40100.2RSPE HIR-40 4 x M8 x 50
Ball screws
Bearing housings
intelligence in motion
WWW.HIWIN.CZ
5.2 Simple bearing housing type SLA
Ball screws
Precise bearing housings SLA are recommended for peeled and ground ball screws.
Ball screws
Bearing housings
Bearing includes:
Simple bearing housing SLA housings
Steel housing
Radial
Simple bearing
bearing housing type SLA
Circlip
Simple bearing housing type SLA
Precise bearing housings SLA are recommended for peeled and ground ball screws.
L2
3 b B1
1
45°
H4
D
d
S1
H
H1
2
H2
H5
H3
L1 S2
L/2
L3
B
(1) Steel housing, (2) Radial bearing, (3) Circlip The axis height of the supported bearing is matched to fixed bearing SFA and nut
(1) Steel pillow block housing, (2) Bearing, (3) Circlip housing GFD. The housing can be screwed on from above (S1) and below (S2).
The reference edge makes it easier to align the unit. The end machining suited to
the supported bearing is the S5-xx or S1-xx type.
18 / 19
SLA-30 6206.2RS
40 SLA-30 126 82 84 105 92 50 32 13 23 21 16 38 11,0 12,6 BALL
M14 SCREWS
30 62 30 x 1,5 6206.2RS
50 SLA-40 146 82 104 125 112 60 32 13 30 21 18 44 13,0 12,6 M14 40 80 40 x 1,75 6208.2RS
50 SLA-40 146 82 104 125 112 60 32hiwin 13 s.r.o.,
30 21info@hiwin.cz,
18 44 13,0 12,6 www.hiwin.cz
M14 40 80 40 x 1,75 6208.2RS
Dimensions in [mm]
www.hiwin.cz
Ball screws
Bearing housings
The axis height of the fixed bearing BK is matched to supported bearing BF.
The end machining suited to fixed bearing BK is the E2B-xx type.
2-M 2-M1 1
2-ØX hole,2-ØX
ØY counter
hole, ØYbore,
counter bore, (L2) (L2)
L3 L3
counter bore
counter
depthbore
Z depth Z
B1 B1 T T
2 2 5 5
7 4 7 4
Ød
Ød
H
H
H1
H1
h
6 6
b b 3 3 C1 C2C1 C2
P P
L1 L
L1 L
B B
(1) Housing, (2) Bearing, (3) Retaining cover, (4) Support ring, (5) Seal, (6) Clamping nut, (7) Allen set screw
End
Type Ød L L1 L2 L3 B H b ±0.02 h ±0.02 B1 H1 P C1 C2 X Y Z M T machi- Bearing
ning
BK-10 10 25 5 29.5 5 60 39 30 22 34 32.5 46 13 6 6.6 10.8 5.1 M3 16 E2B-10 7000A
BK-12 12 25 5 29.5 5 60 43 30 25 34 32.5 46 13 6 6.6 10.8 5.5 M4 19 E2B-12 7001A
BK-15 15 27 6 32.0 6 70 48 35 28 40 38.0 54 15 6 6.6 11.0 6.5 M4 22 E2B-15 7202A
BK-17 17 35 9 44.0 7 86 64 43 39 50 55.0 68 19 8 9.0 14.0 8.5 M4 24 E2B-17 7003A
BK-20 20 35 8 43.0 8 88 60 44 34 52 50.0 70 19 8 9.0 14.0 8.5 M4 30 E2B-20 7204A
BK-25 25 42 12 54.0 9 106 80 53 48 64 70.0 85 22 10 11.0 17.0 11.0 M6 35 E2B-25 7205A
BK-30 30 45 14 61.0 9 128 89 64 51 76 78.0 102 23 11 14.0 20.0 13.0 M6 40 E2B-30 7206A
BK-40 40 61 18 76.0 15 160 110 80 60 100 90.0 130 33 14 18.0 26.0 17.5 M6 50 E2B-35 7208A
Dimensions in [mm]
INTELLIGENCE IN MOTION
Ball screws
Bearing housings
5.4 Simple bearing housing type BF
The axis height of the supported bearing is matched to fixed bearing BK.
The end machining suited to supported bearing BF is the E5B-xx type.
2-ØX
2-ØXhole,
hole,ØYØYcounter
2-ØX
counter
hole,
bore,
bore,
ØY counter bore, B1B1 B1
counter
counterbore
boredepth
counter
depthZ Zbore depth Z 33 22 31 1 2 1
Ød
Ød
Ød
H
H
H
H1
H1
H1
h
h
bb b
PP P
BB B LL L
(1)(1)Housing,
Housing,(2)
(1)(2)Bearing,
Housing,
Bearing,(3)
(2)(3)Circlip
Bearing,
Circlip (3) Circlip
Dimensions in [mm]
20 / 21
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
Ball screws
www.hiwin.cz
Bearing housings
Ball screws
Fixed bearing housing type EK
Bearing housings
The axis height of the fixed bearing is matched to supported bearing EF. The end
machining suited to fixed bearing EK is the E2E-xx type.
2-M
2-ØX hole, ØY counter bore, (L2) L3
counter bore depth Z
B1 T 2
4 3 5
7
1
Ød
H1
H
b
P
B L1 L
(1) Housing, (2) Bearing, (3) Retaining cover, (4) Support ring, (5) Seal, (6) Clamping nut, (7) Allen set screw
b h End
Type
Type Ball screw size d d
Ball screw L L1 L1 L2 L2L3 L3B HB ± H ± b B1 H1 h P B1 X H1Y PZ MX T Y machi-Z Bearing
M T
size 0.02 0.02 ± 0.02 ± 0.02 ning
EK-06 8, 10* 6 20 5.5 22 3.5 42 25 21 13 18 20 30 5.8 9.5 11 M3 12 E2E-06 706A
EK-06 8, 10* 6 20 5.5 22 3.5 42 25 21 13 18 20 30 5.8 9.5 11 M3 12
EK-08 10*, 12 8 23 7.0 26 4.0 52 32 26 17 25 26 38 6.6 11.0 12 M3 14 E2E-08 708A
EK-08 10*, 12 8 23 7.0 26 4.0 52 32 26 17 25 26 38 6.6 11.0 12 M3 14
* EK-06 suitable for ball screws 10x4 Dimensions in [mm]
EK-08 suitable for ball screws 10x2.5
KuličKové šrouby
HIWIN S.R.O., INFO@HIWIN.CZ, WWW.HIWIN.CZ 30 / 31
INTELLIGENCE IN MOTION
Ball screws
Bearing
Ball screwshousings
Bearing housings
Simple bearing housing type EF
3 2 1
Ød
H
H1
h
b
P
B L
KuličKové šrouby
HIWIN S.R.O., INFO@HIWIN.CZ, WWW.HIWIN.CZ 30 / 31
22 / 23
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Bearing housings
5.7 Fixed bearing housing type FK
End
Bea-
Type Ød1 L H F E ØDg6 ØA PCD B L1 T1 L2 T2 X Y Z M T machi-
ring
ning
FK-06 6 20 7 13 22.0 22 36 28 28 5.5 3.5 6.5 4.5 3.4 6.5 4 M3 12 E2F-06 706A
FK-08 8 23 9 14 26.0 28 43 35 35 7.0 4.0 8.0 5.0 3.4 6.5 4 M3 14 E2F-08 708A
FK-10 10 27 10 17 29.5 34 52 42 42 7.5 5.0 8.5 6.0 4.5 8.0 4 M3 16 E2F-10 7000A
FK-12 12 27 10 17 29.5 36 54 44 44 7.5 5.0 8.5 6.0 4.5 8.0 4 M4 19 E2F-12 7001A
FK-15 15 32 15 17 36.0 40 63 50 52 10.0 6.0 12.0 8.0 5.5 9.5 6 M4 22 E2F-15 7002A
FK-17 17 45 22 23 47.0 50 77 62 61 11.0 9.0 14.0 12.0 6.6 11.0 10 M4 24 E2F-17 7203A
FK-20 20 52 22 30 50.0 57 85 70 68 8.0 10.0 12.0 14.0 6.6 11.0 10 M4 30 E2F-20 7204A
FK-25 25 57 27 30 59.0 63 98 80 79 13.0 10.0 20.0 17.0 9.0 15.0 13 M5 35 E2F-25 7205A
FK-30 30 62 30 32 61.0 75 117 95 93 11.0 12.0 17.0 18.0 11.0 17.5 15 M6 40 E2F-30 7206A
Dimensions in [mm]
INTELLIGENCE IN MOTION
WWW.HIWIN.CZ
Ballscrews
Ball screws
Bearinghousings
Bearing housings
5.8 Simple bearing housing type FF
Simple bearing housing type FF
The associated fixed bearing unit is the FK bearing series.
The end machining suited to supported bearing FF is the E5F-xx type.
End
TypeType d1Ød1 L L H H F F ØDg6
Dg6 A ØA PCDPCD B B X X Y Y Z Z machining Bearing
FF-06
FF-06 6 6 10 10 6 6 4 4 22 22 36 36 28 28 28 28 3,4 3.4 6,5 6.5 4,0 4.0 E5F-08
E5F-08 606ZZ
606 ZZ
FF-10
FF-10 8 8 12 12 7 7 5 5 28 28 43 43 35 35 35 35 3,4 3.4 6,5 6.5 4,0 4.0 E5F-10
E5F-10 608ZZ
608 ZZ
FF-12
FF-12 10 10 15 15 7 7 8 8 34 34 52 52 42 42 42 42 4,5 4.5 8,0 8.0 4,0 4.0 E5F-12
E5F-12 60006000ZZ
ZZ
FF-15
FF-15 15 15 17 17 9 9 8 8 40 40 63 63 50 50 52 52 5,5 5.5 9,5 9.5 5,5 5.5 E5F-15
E5F-15 60026002ZZ
ZZ
FF-17
FF-17 17 17 20 20 11 11 9 9 50 50 77 77 62 62 61 61 6,6 6.6 11,011.0 6,5 6.5 E5F-17
E5F-17 62036203ZZ
ZZ
FF-20
FF-20 20 20 20 20 11 11 9 9 57 57 85 85 70 70 68 68 6,6 6.6 11,011.0 6,5 6.5 E5F-20
E5F-20 62046204ZZ
ZZ
FF-25
FF-25 25 25 24 24 14 14 10 10 63 63 98 98 80 80 79 79 9,0 9.0 14,014.0 8,5 8.5 E5F-25
E5F-25 62056205ZZ
ZZ
FF-30
FF-30 30 30 27 27 18 18 9 9 75 75 117117 95 95 93 93 11,011.0 17,017.0 11,011.0 E5F-30
E5F-30 62066206ZZ
ZZ
Dimensions in [mm]
Dimensions in [mm]
24 //37
25
BALLšrouby
KuličKové SCREWS
hiwin
HIWIN s.r.o.,
S.R.O., info@hiwin.cz,
INFO@HIWIN.CZ, www.hiwin.cz
WWW.HIWIN.CZ 36
www.hiwin.cz
WWW.HIWIN.CZ
Ball screws
Ball screws
Bearing housings
Bearing housings
5.9 WBK bearing housings for high load
Thanks to their robust steel bearing housing, the flange bearing units of the WBK series are especially suited to use in heavy-duty ballscrews. Depending on the axial loads present,
the
WBK bearing
WBK bearinghousings
units are for high load
available with the DF, DFD and DFF bearing arrangements.
The end machining processes suited to the WBK fixed bearing are types WS2 and WS3.
Thanks to their robust steel bearing housing, the flange bearing units of the WBK series are especially suited to use in heavy-duty ballscrews. Depending on the axial
loads present, the WBK bearing units are available with the DF, DFD and DFF bearing arrangements.
The end machining processes suited to the WBK fixed bearing are types W2 and W5.
High load bearing set WBK includes:
Steel bearing housing
Angular contact ball bearing (2, 3 or 4 pcs)
Spacer (2 pcs)
Lock nut
PCD W PCD W
d1 H8
d1 H8
D g6
D1
D2
d
DV DV
PC PC
6-ØX hole 8-ØX hole counter bore ØY,
counter bore ØY, depth Z depth Z
A A
l l
L1 L2
L
Ball screw
Type d D D1 D2 L L1 L2 A W X Y Z d1 l V P Q
size
WBK-15-DF 20 15 70 106 72 60 32 15 80 88 9 14 8.5 45 3 58 M5 10
WBK-17-DF 25 17
d 70
D 106
D1 72
D2 60
L 32
L1 15
L2 80
A 88
W X9 14
Y 8.5
Z 45
d1 l3 58
V M5
P 10
Q
WBK-20-DF 25 20 70 106 72 60 32 15 80 88 9 14 8.5 45 3 58 M5 10
WBK-15-DF 20 15 70 106 72 60 32 15 80 88 14 14 8,5 45 3 58 M5 10
WBK-25-DF 32 25 85 130 90 66 33 18 100 110 11 17.5 11 57 4 70 M6 12
WBK-17-DF 25 17 70 106 72 60 32 15 80 88 14 14 8,5 45 3 58 M5 10
WBK-25-DFD 32 25 85 130 90 81 48 18 100 110 11 17.5 11 57 4 70 M6 12
WBK-20-DF 25 20 70 106 72 60 32 15 80 88 14 14 8,5 45 3 58 M5 10
WBK-25-DFF 32 25 85 130 90 96 48 18 100 110 11 17.5 11 57 4 70 M6 12
WBK-25-DF 32 25 85 130 90 66 33 18 100 110 17,5 17,5 11 57 4 70 M6 12
WBK-30-DF 40 30 85 130 90 66 33 18 100 110 11 17.5 11 57 4 70 M6 12
WBK-25-DFD 32 25 85 130 90 81 48 18 100 110 17,5 17,5 11 57 4 70 M6 12
WBK-30-DFD 40 30 85 130 90 81 48 18 100 110 11 17.5 11 57 4 70 M6 12
WBK-30-DF 40 30 85 130 90 66 33 18 100 110 17,5 17,5 11 57 4 70 M6 12
WBK-30-DFF 40 30 85 130 90 96 48 18 100 110 11 17.5 11 57 4 70 M6 12
WBK-30-DFD 40 30 85 130 90 81 48 18 100 110 17,5 17,5 11 57 4 70 M6 12
WBK-35-DF 40 35 95 142 102 66 33 18 106 121 11 17.5 11 69 4 80 M6 12
WBK-35-DF 45 35 95 142 102 66 33 18 106 121 17,5 17,5 11 69 4 80 M6 12
WBK-35-DFD 40 35 95 142 102 81 48 18 106 121 11 17.5 11 69 4 80 M6 12
WBK-35-DFD 45 35 95 142 102 81 48 18 106 121 17,5 17,5 11 69 4 80 M6 12
WBK-35-DFF 40 35 95 142 102 96 48 18 106 121 11 17.5 11 69 4 80 M6 12
WBK-35-DFF 45 35 95 142 102 96 48 18 106 121 17,5 17,5 11 69 4 80 M6 12
WBK-40-DF 50 40 95 142 102 66 33 18 106 121 11 17.5 11 69 4 80 M6 12
WBK-40-DF 50 40 95 142 102 66 33 18 106 121 17,5 17,5 11 69 4 80 M6 12
WBK-40-DFD 50 40 95 142 102 81 48 18 106 121 11 17.5 11 69 4 80 M6 12
WBK-40-DFD 50 40 95 142 102 81 48 18 106 121 17,5 17,5 11 69 4 80 M6 12
WBK-40-DFF 50 40 95 142 102 96 48 18 106 121 11 17.5 11 69 4 80 M6 12
WBK-40-DFF 50 40 95 142 102 96 48 18 106 121 17,5 17,5 11 69 4 80 M6 12
Dimensions in [mm]
Dimensions in [mm]
INTELLIGENCE IN MOTION
Ball screws
Bearing housings
Bearing arrangements
Bearing arrangements
Bearing structure
Bearing structure
1 2 3 4 5 6 7
1 2 3 4 5 6 7
ØD3
MM
ØD3
L3
L3
A
A B
B
(1) bolt,
(1) Mounting Mounting bolt, cover,
(2) Bearing (2) Bearing cover,housing,
(3) Bearing (3) Bearing housing,(5)(4)
(4) Bearing, Bearing,
Seal, (5) Seal,
(6) Spacer, (6) Spacer,
(7) Lock nut (7) Lock nut
(1) Mounting bolt, (2) Bearing cover, (3) Bearing housing, (4) Bearing, (5) Seal, (6) Spacer, (7) Lock nut
Note: Note:Note:
1. Use
1. Use reference reference
planes A and Bplanes A and Bduring
for alignment for alignment
assembly.during assembly.
1.
2. highUse reference
Toaccuracy,
ensure high planes
accuracy,A and B for
parts alignment
6 must notduring
1 –disassembled.. assembly.
be disassembled.
2. To ensure parts 1 – 6 may not be
2. To ensure high accuracy, parts 1 – 6 must not be disassembled.
Dynamic Max. axial Preload Axial rigidity Starting torque Lock nut Weight
Type Table 7.12 Technical data of bearing
capacitydata
Table 7.12 Technical [kN]of bearing
force [kN] [kN] [N/μm] [Nm] M D3 L3 [kg]
WBK-15-DFArticle no. Dynamic
21.9 load 26.6Permissible2.15 Preload [kN]750 Axial rigidity
0.19 StartingM15x1 Lock nut30 14 1.20 Weight
Article no. Dynamic
rating load Permissible
[kN] axial load [kN] Preload [kN] Axial
[N/µm]rigidity Starting
torque [Nm] Lock nut Weight
[kg]
WBK-17-DF 22.4 27.1 2.20 750 0.19 M17x1 M 37 D3 L318 1.24
Nut tightening
rating [kN] axial load [kN] [N/µm] torque [Nm] M D3 L318 Nut tightening [kg]
WBK-20-DF 22.4 27.1 2.20 750 0.19 M20x1 40 torque 2.0
[Nm]
WBK-25-DFWBK15DF 29.1 41.526.6 3.20 2.15 1000 0.29 M25x1.5
torque3.3[Nm]
21.9 750 0.19 M15 × 1 45 30 14 20 52 1.9
WBK15DF
WBK-25-DFD 21.94.7 26.6
83.026.6 2.15
4.40 2.15 1500 750 0.40 0.19 M25x1.5 M15 × 1 30 14 20 52 3.8 1.9
WBK17DF 21.9 750 0.19 M17 × 1 45 32 16 74 1.9
WBK17DF
WBK-25-DFF 21.9 26.6 2.15 750 0.19 M17 × 1 32 16 74 1.9
WBK20DF 21.94.7 83.026.6 6.40 2.15 2000 750 0.50 0.19 M25x1.5 M20 × 1 45 38 16 20 118 4.5 1.9
WBK-30-DFWBK20DF 21.9
29.8 44.026.6 3.40 2.15 1050 750 0.30 0.19 M30x1.5 M20 × 1 50 38 16 20 118 3.2 1.9
WBK25DF 28.5 40.5 3.15 1000 0.29 M25 × 1.5 38 18 188 3.1
WBK25DF
WBK-30-DFD 28.5
48.5 88.040.5 4.60 3.15 1550 1000 0.40 0.29 M30x1.5 M25 × 1.5 38 18 188 3.1
WBK25DFD 46.5 81.5 4.3 1470 0.39 M25 × 1.550 38 18 20 188 3.7 3.4
WBK25DFD
WBK-30-DFF 46.5
48.5 88.081.5 6.80 4.3 2050 1470 0.52 0.39 M30x1.5 M25 × 1.550 38 18 20 188 4.3 3.4
WBK30DF 29.2 43.0 3.35 1030 0.30 M30 × 1.5 45 18 260 3.0
WBK-35-DFWBK30DF 31.5
29.2 51.043.0 3.90 3.35 1200 1030 0.35 0.30 M35x1.5 M30 × 1.555 45 18 22 260 3.8 3.0
WBK30DFD 47.5 86.0 4.5 1520 0.40 M30 × 1.5 45 18 260 3.3
WBK-35-DFD
WBK30DFD 51.5
47.5 102.086.0 5.30 4.5 1750 1520 0.46 0.40 M35x1.5 M30 × 1.555 45 18 22 260 4.5 3.3
WBK35DF 31.0 50.0 3.8 1180 0.34 M35 × 1.5 52 18 340 3.4
WBK-35-DFF
WBK35DF 51.5
31.0 102.050.0 7.80 3.8 2400 1180 0.60 0.34 M35x1.5 M35 × 1.555 52 18 22 340 5.2 3.4
WBK35DFD
WBK-40-DFWBK35DFD
50.5
32.5
100.0
53.0 4.00
5.2 1250
1710 0.37
0.45 M40x1.5
M35 × 1.560 52 18 22 340 3.7 4.3
50.5 100.0 5.2 1710 0.45 M35 × 1.5 52 18 340 4.3
WBK35DFF
WBK-40-DFD 50.5
52.5 100.0
106.0 5.40 7.65 1850 2350 0.47 0.59 M40x1.5 M35 × 1.560 52 18 22 340 4.2 5.0
WBK35DFF 50.5 100.0 7.65 2350 0.59 M35 × 1.5 52 18 340 5.0
WBK40DF
WBK-40-DFF 31.5
52.5 106.052.0 8.00 3.9 2450 1230 0.62 0.36 M40x1.5 M40 × 1.560 58 20 22 500 5.0 3.6
WBK40DF 31.5 52.0 3.9 1230 0.36 M40 × 1.5 58 20 500 3.6
WBK40DFD 51.5 104.0 5.3 1810 0.47 M40 × 1.5 58 20 500 4.2
WBK40DFD 51.5 104.0 5.3 1810 0.47 M40 × 1.5 58 20 500
Dimensions
4.2
WBK40DFF 51.5 104.0 7.85 2400 0.61 M40 × 1.5 58 20 500in [mm] 4.7
WBK40DFF 51.5 104.0 7.85 2400 0.61 M40 × 1.5 58 20 500 4.7
26 / 27
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
WWW.HiWin.cZ
www.hiwin.cz
WWW.HIWIN.CZ
Ball
Ball screws
screws
Ball screws
Bearing
Bearing housings
housings
Bearing housings
SBKbearing
5.10 SBK bearinghousings
housingsforforhigh
highload
load
Thanks
Thanks to their torobust
their robust steel bearing
steel bearing housing,housing, the bearing
the bearing unitsunits
of theof SBK
the SBK series
series are are especially
especially suited
suited to touseuseininheavy-duty
heavy-dutyballscrews.
ballscrews.Depending
Depending on
on the
the axial
axial loads
loadspresent,
present,the SBK
WBK bearing
the SBK bearing
bearing units arehousings
units are availablefor
available withhigh
with theload
the DF
DF and
and DFD
DFD bearing
bearing arrangements.
arrangements.
The end The end machining
machining processesprocesses
suited tosuited to the
the SBK fixedSBK fixed are
bearing bearing
typesareWS2
types
andWS2
WS3.and WS3.
Bearing arrangements
1 2 3 5 4
4-ØX
4-ØX drilldrill ØY counter
ØY counter bore depthbore
Z depth Z
Ød1
Ød
A
h H1
I I
E L1 L1
B L L
Supported
Type d A h H1 L L1 L3 B d1 E C2 C1 X Y Z I V P Q H side
�0.02
Type SBK 25DF Ball screw d A53 66 h
H1
25size89 51 ± 0.02 71 18 L 160L1 57L3 130 B 15.5d1 40 E 18 C2 26 C1 2 X4 Y70 Z
M6 I
10 V
M6 P SF25 Q H
SBK 25DFD 81
SBK-25-DF
SBK 30DF 32 25 89 6651 53 66 71 18 160 57 130 15.5 40 18 26 2 4 70 M6 10 M6
30 89 51 53 71 18 160 57 130 15.5 40 18 26 2 4 70 M6 10 M6 BF30
SBK-25-DFD
SBK 30DFD 32 25 89 8151 53 81 71 18 160 57 130 15.5 40 18 26 2 4 70 M6 10 M6
SBK-30-DF
SBK 35DF 40
35 96
30
52
89
54
6651 53 1866 16071 69 18 130160 15.5 57 40 130 18 15.526 40
71
184 2680 2 4
10
70 M6 10 M6
2 M6 M6 BF35
SBK-30-DFD
SBK 35DFD 40 30 89 8151 53 81 71 18 160 57 130 15.5 40 18 26 2 4 70 M6 10 M6
SBK 40DF
SBK-35-DF 6652
40 40
96 35
52 96
54 7154 1866 16071 69 18 130160 15.5 69 40 130 18 15.526 40 2 184 2680 2
M6 4
10 80
M6 M6SF4010 M6
SBK 40DFD 81
SBK-35-DFD 40 35 96 52 54 81 71 18 160 69 130 15.5 40 18 26 2 4 80 M6 10 M6
SBK-40-DF 50 40 96 52 54 66 71 18 160 69 130 15.5 40 18 26 Dimensions
2 4in [mm]
80 M6 10 M6
SBK-40-DFD 50 40 96 52 54 81 71 18 160 69 130 15.5 40 18 26 2 4 80 M6 10 M6
Dimensions in [mm]
Dimensions in [mm]
INTELLIGENCE IN MOTION
Ball screws
Bearing housings
C2 45°
45°
C1 L1
DF Type
C2
C1 L1
Back view 4-P
4-Pdpdp
Q PCD ØV ØV
Q PCD
both
bothsides
sides
DFD Type
6
ØD3
M
Ød
M
Assembly on shaft
L3
Lock nut
Lock nut
Dynamic Max. axial Preload Axial rigidity Starting torque Lock nut Weight
Type
capacity [kN] force [kN] [kN] [N/μm] [Nm] M D3 L3 [kg]
SBK-25-DF 29.1 41.5 3.2 1000 0.29 M25x1.5 45 20 4.46
SBK-25-DFD 47.0 83.0 4.4 1500 0.40 M25x1.5 45 20 5.25
SBK-30-DF 29.8 44.0 3.4 1050 0.30 M30x1.5 50 20 4.35
SBK-30-DFD 48.5 88.0 4.6 1550 0.40 M30x1.5 50 20 5.09
SBK-35-DF 31.5 51.0 3.9 1200 0.35 M35x1.5 55 22 4.57
SBK-35-DFD 51.5 102.0 5.3 1750 0.46 M35x1.5 55 22 5.30
SBK-40-DF 32.5 53.0 4.0 1250 0.37 M40x1.5 60 22 4.60
SBK-40-DFD 52.5 106.0 5.4 1850 0.47 M40x1.5 60 22 5.15
Dimensions in [mm]
55
28 / 29
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Shaft ends LP
S2
O d2
O d0
O d3
O d1
B P9 / T
LB LZ
6.1 Standard shaft ends for SFA fixed bearing housings DIN 509
L2
Type S2 LP Type S3
S2 S3
O d2
O d2
O d0
O d0
O d3
O d1
O d1
B P9 / T
LB LZ LZ DIN 509
DIN 509
L2 L3
S3
Dimensional table for S2 and S3 shaft
Typ S2ends
Typfor
S3 SFA
Pro bearing
ulozeni housing
d0 d1 d2 d3 L2 L3 LB LZ LP BxT
S2-06 S3-06 SFA-06 8, 10, 12 6 h5 M 6x0,5 5 j6 37 21 16 10 - -
O d2
O d0
O d1
Type S2 Type S3 Bearing housing d0 d1 d2S2-10 S3-10d3 SFA-10 L2 16 10 h5L3 M 10x0,75 8LB j6 50 30LZ 20 12 LP
14 2x1,2 B x X
S2-12 S3-12 SFA-12 20 12 h5 M 12x1 10 j6 58 35 23 12 16 3x1,8
S2-06 S3-06 SFA-06
LZ DIN 8,
50910, 12 6 h5 M6x0.5S2-17 5 j6
S3-17 SFA-17 37 25 17 h521 M 17x1 1416j6 73 43 10 30 20 20- 5x3,0 -
S2-10 S3-10 SFA-10L3 16 10 h5 M10x0.75 S2-20 S3-20
8 j6 SFA-20 50 25, 32 20 h530 M 20x1 1420j6 76 46 12 30 20 20
14 5x3,0 2x1.2
S2-25 S3-25 SFA-25 32, 40 25 h5 M 25x1,5 20 j6 96 46 50 21 36 6x3,5
S2-12 S3-12 SFA-12 20 12 h5 M12x1 S2-30 10 j6
S3-30 SFA-30 58 40 30 h535 M 30x1,5 2523j6 108 48 12 60 22 16
45 8x4,0 3x1.8
S2-40 S3-40 SFA-40
S2-17 S3-17 SFA-17 25 17 h5 M17x1 S2-50
14 j6
S3-50
73 50 40 h5 M 40x1,5 32 k6 135 55 80
43 30
63 50 h5 M 50x1,5 40 k6 155 55 100
20 24
24
56
20
70
10x5,0
12x4,0
5x3.0
S2-20 S3-20 RozmerovaSFA-20
tabulka opracovaní S2 a S3 pro25, 32 SFA
ulozeni 20 h5 M20x1 S2-60 14 j6
S3-60 76 80 60 h546 M 60x2 5030k6 177 67 20 110 25 20
70 14x5,0 5x3.0
Typ S2 Typ S3 Pro ulozeni d0 d1 d2 d3 L2 L3 LB LZ LP B x T
S2-25
S2-06 S3-25 SFA-06 8, -10, 12 6 h5 M 6x0,5 5 j6 32,3740 21
S3-06 1625 h510 -M25x1.5
- 20 j6 96 46 50 21 36 6x3.5
S2-30S2-10 S3-30 SFA-10
S3-10 SFA-30
16 10 h5 M 10x0,75 8 j6 5040 30 2030 h512 14M30x1.5
2x1,2 25 j6 108 48 60 22 45 8x4.0
S2-12 S3-12 SFA-12 20 12 h5 M 12x1 10 j6 58 35 23 12 16 3x1,8
S2-40S2-17 S3-40
S3-17 SFA-17 SFA-40
25 17 h5 M 17x1 14 j6 7350 43 3040 h520 20M40x1.5
5x3,0 32 k6 135 55 80NAZEV 24 56 10x5.0
Opracovani koncu S2 a S3 pro ulozeni SFA
S2-50
S2-20 S3-50 SFA-20 25,- 32 20 h5 M 20x1 14 j6 7663 46
S3-20 3050 h520 20M50x1.5
5x3,0 40 k6 155 55 100 24 70 12x4.0
S2-25 S3-25 SFA-25 32, 40 25 h5 M 25x1,5 20 j6 96 46 50 21 36 6x3,5 SIZE c. vykr.
S2-60S2-30 S3-60 SFA-30
S3-30 -40 30 h5 M 30x1,5 25 j6 10880 48 6060 h522 45 M60x2
8x4,0 50 k6 177 JMENO67 DATUM 110 A4 25Standardni konce 70 14x5.0
7
S2-40 S3-40 SFA-40 50 40 h5 M 40x1,5 32 k6 135 55 80 24 56 10x5,0 NAKRESLIL Lukas 03.06.2014 SOUBOR: S2+S3 pro SFA.dft
S2-50 S3-50 63 50 h5 M 50x1,5 40 k6 155 55 100 24 70 12x4,0 ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
S2 type without keyway
S2-60 S3-60 - S21 80 60 h5 M 60x2 50 k6 177 67 110 25 70 14x5,0 Dimensions in [mm]
S5
O d0
O dE
O d1
NAZEV
6.2 Standard shaft ends for SLA simple bearing housings Opracovani koncu S2 a S3 pro ulozeni SFA LE H13 L15 DIN 509
JMENO DATUM
SIZE c. vykr. L5
A4 Standardni konce 7
NAKRESLIL Lukas 03.06.2014 SOUBOR: S2+S3 pro SFA.dft
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
Type S5 Type S1 LP
S5 S1
O d2
O d0
O d3
O d1
O d0
O dE
O d1
B P9 / T
S1
Typ S5bearing
Dimensional table for S5 and S1 shaft end for SLA Typ S1 housing
Pro ulozeni d0 d1 d2 d3 dE L1 L5 L15 LB LZ LP LE BxT
S5-06 S1-06 SLA-06 8, 10, 12 6 j6 M6x0.5 5 j6 5.7 h10 31 8 6 16 10 - 0.8 -
O d2
O d0
O d3
O d1
LB LZ
DIN 509 S5-20 S1-20 SLA-20 25, 32 20 j6 M20x1 14 j6 19 h12 42 17 14 30 20 20 1.3 5x3.0
S5-06 S1-06
L1 SLA-06 8, 10, 12 6 j6 M6x0.5 5 j6 5.7 h10 S5-25 31S1-25 8
SLA-25 32, 640 25 j6 16M25x1.5 20
10j6 23.9 h13- 83 180.815 50 21 - 36 1.3 6x3.5
S5-10 S1-10 SLA-10 16 10 j6 M10x0.75 8 j6 9.6 h10 S5-30 39S1-30 12
SLA-30 409 30 j6 20M30x1.5 2512j6 28.6 h12
14 95 201.116 602x1.2
22 45 1.6 8x4.0
S5-40 S1-40 SLA-40 50 40 j6 M40x1.5 32 k6 37.5 h12 119 22 18 80 24 56 1.85 10x5.0
S5-12 S1-12 SLA-12 20 12 j6 M12x1 10 j6 11.5 h11 S5-50 43S1-50 13- 10
63 50 j6 23M50x1.5 40 12k6 47 h1216 142 251.120 1003x1.8
24 70 2.15 12x5.0
Rozmerova tabulka opracovani S5 a S1 pro ulozeni SLA
Typ S5-17
S1 Pro ulozeni d0S1-17d1 d2 SLA-17 25 LZ17 j6LP LE BM17x1 14 j6 16.2 h11 S5-60 60S1-60 15- 12
80 60 j6 30M60x2 50 20k6 57 h1220 155 281.122 1105x3.0
25 70 2.15 14x5.0
Typ S5 d3 dE L1 L5 L15 LB xT
S5-06 S5-20SLA-06 8, 10,S1-20
S1-06 12 6 j6 M6x0.5SLA-205 j6 5.7 h10 31 25, 8 32 6 16 1020 j6- 0.8 M20x1
- 14 j6 19 h12 42 17 14 30 20 20 1.3 5x3.0
S5-10 S1-10 SLA-10 16 10 j6 M10x0.75 8 j6 9.6 h10 39 12 9 20 12 14 1.1 2x1.2
S5-12
S5-25
S1-12 SLA-12
S1-25 -
20 12 j6 M12x1 10 j6 11.5 h11 43 13 10
32, 40 23
25 j6
12 16
M25x1.5
1.1 3x1.8
20 j6 23.9 h13 83 18 15 50 21 36 1.3 6x3.5
S5-17 S5-30SLA-17 25S1-30
S1-17 17 j6 M17x1 SLA-30
14 j6 16.2 h11 60 15 40 12 30 30 j620
20 1.1 M30x1.5
5x3.0 25 j6 28.6 h12 95 20 16 60 22 45
NAZEV 1.6 8x4.0
S5-20 S1-20 SLA-20 25, 32 20 j6 M20x1 14 j6 19 h12 42 17 14 30 20 20 1.3 5x3.0
S5-25
S5-40 S1-40 SLA-40
S1-25 SLA-25 32, 40 25 j6 M25x1.5 20 j6 23.9 h13 83 18 15
50 50
40 j6
21 36
M40x1.5
1.3 6x3.5
32 k6 37.5 h12 119 22 18 80 24 56 Opracovani
1.85 koncu10x5.0
S5 a S1 pro ulozeni SLA
SIZE c. vykr.
S5-30 S5-50SLA-30 40S1-50
S1-30 30 j6 M30x1.5- 25 j6 28.6 h12 95 20 63 16 60 50 j645
22 1.6 M50x1.5
8x4.0 40 k6 47 h12 142 25 20 100JMENO 24DATUM 70A4 2.15 Standardni
12x5.0konce 8
S5-40 S1-40 SLA-40 50 40 j6 M40x1.5 32 k6 37.5 h12 119 22 18 80 24 56 1.85 10x5.0
S5-50 S5-60
S1-50 - S1-60 -
63 50 j6 M50x1.5 40 k6 47 h12 142 25 20 80 100 60 j670
24 M60x2
2.15 12x5.0 50 k6 57 h12 155 28 22
NAKRESLIL
110Lukas 05.06. 2014
25 SOUBOR: S5+S1
70 2.15pro SLA.dft
14x5.0
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
S5-60 S1-60 - 80 60 j6 M60x2 50 k6 57 h12 155 28 22 110 25 70 2.15 14x5.0
S1 type without keyway - S11 Dimensions in [mm]
NAZEV
Opracovani koncu S5 a S1 pro ulozeni SLA
JMENO DATUM
SIZE c. vykr.
A4 Standardni konce 8
NAKRESLIL Lukas 05.06. 2014 SOUBOR: S5+S1 pro SLA.dft
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
INTELLIGENCE IN MOTION
Ball screws
Shaft ends LP DIN 509
E2B1
O d0
O d5
O d4
O d1
výchozí
LB LZ
B P9 / T
6.3 Standard shaft end E2B for BK fixed bearing housing L2
E2B1 E2B2
O d0
O d5
O d4
O d0
O d4
O d5
O d1
O d1
Type E2B1 Type E2B2 výchozí Type E2B3
LB LZ LB LZ
B P9 / T
L2 L2
O d0
O d5
O d0
O d5
O d4
O d0
O d4
O d5
O d1
O d1
O d1
výchozí LZ
LB LZ LB LZ
B P9 / T
L2 L2 L3
O d0
O d5
O d1
O d0
O d4
O d5
O d1
O d1
Typ d0 d1 d4 d5 L3E2Bx-40
LP B xBK-40 50 40 143 83 26 10x5,0
E2B_-12 LZ
BK-12 16 12 h6 E2Bx-1010 j6BK-10 M12x1 h6 8 j6 M 10x1
12 10 15 15 16 5114 36 9 51
2x1,2 36 9 3x1.8
E2Bx-12 BK-12 16 12 h6 10 j6 M 12x1 15 14 51 36 9 3x1,8
E2B_-15 BK-15
L3 20 15 h6 E2Bx-1512 j6BK-15 M15x1
20 15 h6 12 j6 M 15x1 20 20 12 6012 40 12 60
4x2,5 40 12 NAZEV 4x2.5
E2Bx-17 BK-17 25 17 h6 15 j6 M 17x1 23 17 76 53 15 5x3,0 Opracovani koncu E2B pro BK
E2B_-17 BK-17 25 17 h6 E2Bx-2015 j6BK-20 M17x1
25 20 h6 17 j6 M 20x1 23 25 15 7817 53 15 76
5x3,0 53 15 SIZE 5x3.0
E2Bx-25 JMENO DATUM A4 Standardni konce 1
E2B_-20 BK-20 25 20 h6 E2Bx-30
17 j6BK-25
BK-30
32 25 h6 20 j6 M 25x1,5 30 18 95
M20x1 25
40 30 h6 25 j6 M 30x1,5 38 25 110
15 65 16
72 23
6x3,5
78 NAKRESLIL 53 Lukas
8x4,0
15 SOUBOR: E2B pro5x3.0
14.05.2014 BK.dft
Rozmerova tabulka opracovaní E2B pro ulozeni BK
E2B_-25
Typ Pro ulozeni d0BK-25 d1 d4 d5 LB LZ 32L2 L3 LP25 h6
BxT E2Bx-4020 j6BK-40 M25x1.5
50 40 h6 35 j6 M 40x1,5 30 50 35 143 18 83 26 95 ZKONTROLOVAL 65
10x5,0 16 MERITKO: 6x3.5
HMOTNOST: SHEET 1 OF 1
E2Bx-10 BK-10 12 10 h6 8 j6 M 10x1 15 16 51 36 9 2x1,2
E2B_-30
E2Bx-12 BK-12 16BK-30
12 h6 10 j6 M 12x1 15 14 4051 36 930 h6
3x1,8 25 j6 M30x1.5 38 25 110 72 23 8x4.0
E2B_-40
E2Bx-15
E2Bx-17
BK-15
BK-17
20BK-40
15 h6 12 j6 M 15x1 20 12 5060
25 17 h6 15 j6 M 17x1 23 17 76
40
53
1240 h6
4x2,5
15 5x3,0
35 j6 M40x1.5 50 NAZEV
Opracovani koncu E2B pro BK143
35 83 26 10x5.0
E2Bx-20 BK-20 25 20 h6 17 j6 M 20x1 25 15 78 53 15 5x3,0 SIZE
JMENO DATUM A4 Standardni konce 1
E2Bx-25
E2Bx-30
BK-25
BK-30
32
40
25 h6
30 h6
20 j6 M 25x1,5 30
25 j6 M 30x1,5 38
18
25
95
110
65
72
16 6x3,5
23 8x4,0 NAKRESLIL Lukas 14.05.2014 SOUBOR: E2B pro BK.dft Dimensions in [mm]
E2Bx-40 BK-40 50 40 h6 35 j6 M 40x1,5 50 35 143 83 26 10x5,0 ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
E5B
NAZEV
6.4 Standard shaft end E5B for BF simple bearing housing
Opracovani koncu E2B pro BK
SIZE
JMENO DATUM A4 Standardni konce 1
NAKRESLIL Lukas 14.05.2014 SOUBOR: E2B pro BK.dft
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
Type E5B
O d10
O d0
O dE
L16 L17
DIN 509
L10
Dimensional
Rozmerova tabulka opracovaní tableBF for E5B shaft end for BF bearing housing
E5B pro ulozeni
Typ Pro ulozeni d0 d10 j6 dE -0,2 L10 L16 L17 H13 Lozisko
E5B-10 BF-10 12 8Bearing7,6 10 7 0,9 608ZZ
E5B-12 Type
BF-12 16 10housing9,6 11 d0 8 d10 j66000ZZ
1,15 dE -0.2 L10 L16 L17 H13
E5B-15 BF-15 20 15 14,3 13 9 1,15 6002ZZ
E5B-17 E5B-10
BF-17 25 BF-10
17 16,2 16 1212 1,15 86203ZZ 7.6 10 7 0.9
E5B-20 BF-20 25 20 19,0 19 14 1,35 6004ZZ
E5B-25 E5B-12
BF-25 32 BF-12
25 23,9 20 16
15 1,35 106205ZZ 9.6 11 8 1.15
E5B-30 E5B-15
BF-30 40 BF-15
30 28,6 21 20
16 1,75 156206ZZ 14.3 13 9 1.15
E5B-40 BF-40 50 40 38,0 23 18 1,95 6208ZZ
E5B-17 BF-17 25 17 16.2 16 12 1.15
E5B-20 BF-20 25 20 19.0 16 12 1.35
E5B-25 BF-25 32 25 23.9 20 15 1.35
E5B-30 BF-30 40 30 28.6 21 16 1.75
E5B-40 BF-40 50 40 38.0 23 18 1.95
NAZEV
Opracovani koncu E5B pro BF
SIZE Dimensions in [mm]
JMENO DATUM A4 Standardni konce 3
NAKRESLIL Lukas 14.05.2014 SOUBOR: E5B pro BF.dft
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
30 / 31
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz WWW.HIWIN.CZ
Ball
Ballscrews
screws
Shaft
Shaftends
ends LP
LP DIN
DIN 509
509
E2B1
d0
OOd5d5
OOd4d4
OOd1d1
OOd0
6.5 Standard
Standard shaft
shaft endend
E2BE2E
forfor
EKEK fixed
fixed bearing
bearing housing
housing vvýchozí
LB LZ ýchozí
LB LZ
BBP9P9 //TT
L2
L2
LP
LP DIN 509
DIN 509 DIN 509
DIN 509
E2B1TypeType E2B2
d0
OOd5d5
OOd4d4
d0
OOd4d4
OOd5d5
OOd1d1
OOd1d1
OOd0
OOd0
Type
TypeE2E1
E2E1 Type E2E2
Type E2E2 LBLB LZ
E2E3E2E3
vvýchozí
ýchozíLB Type
LZ E2E3
LZ
BBP9P9 //TT
LB LZ
L2
L2 L2
L2
LP
LP DIN 509
DIN 509 DIN 509
DIN 509 DIN 509
DIN 509
d0
OOd5d5
d0
OOd5d5
OOd4d4
d0
OOd4d4
OOd5d5
OOd1d1
OOd1d1
OOd1d1
OOd0
OOd0
OOd0
LZ vvýchozí
ýchozí LZ
LZ LZ
LB
LB LZ LB
LB LZ
BBP9P9 //TT
L6
L6
L6 L6
L6
L6 L7
L7
L7
DIN 509
DIN 509 DIN 509
DIN 509
d0
OOd5d5
OOd1d1
d0
OOd4d4
OOd5d5
OOd1d1
OOd0
OOd0
Typ
Typ Pro ulozeni
Pro ulozeni d0
d0 d1
d1 d4
d4 d5
d5 LB LZ
LB LZ L2 L2 L3
L3 LP
LP BB xx TT
LB
LB LZ
LZ Dimensional table of E2E shaft
LZ end for EK bearing housing
LZ
L2
L2 L3
L3
Type Bearing
DINBearing housing d0 d1 d4 d5 LB LZ L6 L7 LP BBxxTT
Type DIN 509
509 d0 d1 d4 d5 LB LZ L6 L7 LP
housing
E2E_-06 EK-06 8, 10* 6 h6 4 j6 M 6x0.75 8 BK 8 36 28 - -
E2E_-06 EK-06 8, 10* E2B3
6 h6 Typ 46j6j6
Rozmerova tabulka
Rozmerova
ulozeniM6x0.75
tabulka opracovaní
8
E2B pro
opracovaní E2B pro ulozeni
ulozeni BK
8 36 TT 28 - -
d0
OOd5d5
OOd1d1
OOd0
SIZE
SIZE
JMENO
JMENO DATUM
DATUM A4
A4 Standardni konce
Standardni konce 11
NAKRESLIL
NAKRESLIL Lukas
Lukas 14.05.2014 SOUBOR:
14.05.2014 E2B pro
SOUBOR: E2B pro BK.dft
BK.dft
ZKONTROLOVAL
ZKONTROLOVAL MERITKO:
MERITKO : HMOTNOST:
HMOTNOST: SHEET
SHEET 11 OF
OF 11
NAZEV
NAZEV
Opracovani
Opracovani koncu
koncu E2B
E2B pro
pro BK
BK
E5B
SIZE
SIZE
JMENO DATUM A4 Standardni konce
konce 11
6.6 Standard shaft end E5ELukas
NAKRESLIL
NAKRESLIL
for EF14.05.2014
Lukas simpleSOUBOR:
14.05.2014
A4
bearing
SOUBOR: E2B pro
E2B
housing
pro BK.dft
BK.dft
Standardni
MERITKO:: SHEET
SHEET 11 OF
OF 11
ZKONTROLOVAL
ZKONTROLOVAL MERITKO HMOTNOST:
HMOTNOST:
Type E5E
Type E5E
d10
d0
dE
O d10
O d0
O dE
O
O
L16
L16 L17
L17
DIN
DIN 509
509
L10
L10
Dimensional Dimensional
Dimensional
table forBF table
table forfor
E5EE5E shaft
shaft endend
forfor
EF EF bearing
bearing housing
housing
BFE5E shaft end for EF bearing housing Type
Rozmerova tabulka
tabulka E5B pro
opracovaní E5B pro ulozeni
Type
Rozmerova opracovaní ulozeni
Typ Pro ulozeni d0 d10 j6
j6 dE -0,2
-0,2 L10 L16 L17 H13
H13 Lozisko
Lozisko
Typ Pro ulozeni d0 Bearing
d10 dE L10 L16 L17
TypeType Bearing housing d0 d0 d10d10
J6 j6 dEdE-0,2
-0.2 L10L10 L16
L16 L17H13
L17 H13
housing
E5E-06
E5E-06 EF-06
EF-06 8,10*
8,10* 66 5.75.7 99 66 0.80.8
E5E-08
E5E-08 EF-08
EF-08 10*,1212
10*, 66 5.75.7 99 66 0.8
0.8
Opracovani koncu
Opracovani koncu E5B
E5B pro
pro BF
BF
SIZE
SIZE
JMENO
JMENO DATUM
DATUM A4
A4 Standardni
Standardni konce
konce 33
NAKRESLIL
NAKRESLIL Lukas
Lukas 14.05.2014
14.05.2014 SOUBOR:
SOUBOR: E5B
E5B pro
pro BF.dft
BF.dft
ZKONTROLOVAL MERITKO:
MERITKO : HMOTNOST: SHEET
SHEET 11 OF
OF 11
ZKONTROLOVAL HMOTNOST:
KuličKové šrouby
HIWIN S.R.O., INFO@HIWIN.CZ, WWW.HIWIN.CZ 40 / 41
INTELLIGENCE IN MOTION
Ball screws
Shaft ends LP DIN 509
E2F1
O d0
O d5
O d4
O d1
6.7 Standard shaft end E2F for FK fixed bearing housing výchozí
LB LX
B P9 / T
L4
E2F1 E2F2
O d0
O d5
O d4
O d1
O d0
O d4
O d5
O d1
Type E2F1 Type E2F2 LB LX
výchozí
LB
Type
LX
E2F3
B P9 / T
L4 L4
O d0
O d5
O d0
O d4
O d5
O d0
O d5
O d4
O d1
O d1
O d1
výchozí
LB LX LB LX LX
B P9 / T
L6 L4 L4 L6 L5
O d0
O d5
O d1
O d0
O d4
O d5
O d1
O d1
E5F
SIZE
Standardni konce 2
NAKRESLIL Lukas 14.05.2014 SOUBOR: E2F pro FK.dft
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
Type E5F
O d10
O d0
O dE
L16 L17
DIN 509
L10
Dimensional
Rozmerova tabulka opracovaní table for E5F shaft end for FF bearing housing
E5F pro ulozeni FF
Typ Pro ulozeni d0 d10 j6 dE -0,2 L10 L16 L17 H13 Lozisko
E5F-08 FF-06 (10) 12 6 Bearing 5,7 9 6 0,8 606ZZ
E5F-10 FF-10 Type 12 8 7,6 10 7 d0 0,9 d10 j6
608ZZ dE -0.2 L10 L16 L17 H13 Bearing
E5F-12 FF-12 16 10 housing
9,6 11 8 1,15 6000ZZ
E5F-15 FF-15 20 15 14,3 13 9 1,15 6002ZZ
E5F-17 E5F-08
FF-17 25 FF-06
17 16,2 16 128, 10 1,15 6203ZZ6 5.7 9 6 0.8 606ZZ
E5F-20 E5F-10
FF-20 25 FF-10
20 19,0 16 12 12 1,35 6004ZZ8 7.6 10 7 0.9 608ZZ
E5F-25 FF-25 32 25 23,9 20 15 1,35 6205ZZ
E5F-30 E5F-12
FF-30 40 FF-12
30 28,6 21 16 16 1,75 10
6206ZZ 9.6 11 8 1.15 6000ZZ
E5F-15 FF-15 20 15 14.3 13 9 1.15 6002ZZ
E5F-17 FF-17 25 17 16.2 16 12 1.15 6203ZZ
E5F-20 FF-20 25 20 19.0 19 14 1.35 6204ZZ
E5F-25 FF-25 32 25 23.9 20 15 1.35 6205ZZ
E5F-30 FF-30 NAZEV
40koncu E5F pro FF
Opracovani 30 28.6 21 16 1.75 6206ZZ
SIZE
JMENO DATUM A4 Standardni konce 4
NAKRESLIL Lukas 14.05.2014 SOUBOR: E5F pro FF.dft Dimensions in [mm]
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
32 / 33
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Shaft ends DIN 76-B
LP
DIN 509
W21
O d0
O d5
O d4
O d1
6.9 Standard shaft ends for bearing housings WBK and SBK LB LZ PRO WBK_DF
B P9 / T
L21
Driven end DIN 76-B DIN 509 DIN 76-B DIN 509
LP LP
O d0
O d4
O d5
O d1
O d0
O d5
O d4
O d1
- WBK_DF - WBK_DFDLB LZ PRO -WBK_DF
WBK_DFFLB LZ PRO WBK_DFD
B P9 / T
B P9 / T
- SBK_DF - SBK_DFD L21 L22
DIN 76-B DIN 509 DIN 76-B DIN 509 DIN 76-B DIN 509
LP LP LP
O d0
O d0
O d4
O d5
O d5
O d5
O d0
O d4
O d4
O d1
O d1
O d1
B P9 / T
B P9 / T
O d5
O d1
O d5
O d0
O d4
W2x-17 O d1
WBK-17 25 17 h5 14 j6 M 17x1 111 - - 30 23 20 5x3,0
LB LZ
Dimensional table ofLBWS2 shaft
PRO WBK_DFD LZ
ends for WBK and SBK bearing housing
W2x-20
PRO W2x-25 WBK-20
WBK_DFFWBK-25 25 20 h5 17 j6 M 20x1 111 - - 30 23 20 5x3,0
B P9 / T
O d0
O d4
O d1
O d0
O d1 Dimensions in [mm]
W2x-20 WBK-20 25 20 h5 17 j6 M 20x1 111 - - 30 23 20 5x3,0
NAKRESLIL Lukas 30.05.2014 SOUBOR: W2 pro WBK.dft
W2x-25 WBK-25 32 25 h5 20 j6 M 25x1,5 139 154 - 50 26 36 6x3,5
W2x-30 WBK-30 40 30 h5 25 j6 M 30x1,5 149 164 - 60 26 45 8x4,0 ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1 PRO WBK_DF
LZ
W2x-35 WBK-35 40 35 h5 30 j6 M 35x1,5 152 167 182 60 30 45 8x4,0
W2x-40 WBK-40 50 40 h5 35 k6 M 40x1,5 172 187 202 80 10 56 10x5,0 L51
Supported end
NAZEV DIN 76-B DIN 509 DIN 76-B DIN 509
Opracovani koncu W2 pro WBK
O d1
O d5
O d0
O d1
- WBK_DF NAKRESLIL
ZKONTROLOVAL
Lukas 30.05.2014 SOUBOR: W2 pro WBK.dft
MERITKO: HMOTNOST: SHEET 1 OF 1
- WBK_DFD - WBK_DFF
PRO WBK_DF PRO WBK_DFD
- SBK_DF - SBK_DFD
LZ LZ
L51 L52
DIN 76-B DIN 509 DIN 76-B DIN 509 DIN 76-B DIN 509
O d0
O d1
O d5
O d0
O d0
O d5
O d1
O d1
DIN 76-B DIN 509 DIN 76-B DIN 509 Rozmerova tabulka opracovani W5 pro ulozeni WBK
Typ Pro ulozeni d0 d1 d5 L51 L52 L53 LZ
O d1
O d5
O d0
O d1
O d0
O d1
SIZE
W5x-17 WBK-17 25 17 h5 M 17x1 81 - - 23 JMENO DATUM A4 Standardni konce 6
WS3_-20 WBK-20 - 25
PRO WBK_DFF
W5x-2020 h5 WBK-20 M20x1
25 20 h5 M 20x1 81 81 - -- 23 - 23
NAKRESLIL Lukas 30.05.2014 SOUBOR: W5 pro WBK.dft
W5x-25 WBK-25 32 25 h5 M 25x1,5 89 104 - 26
WS3_-25LZ WBK-25 SBK-25 32 W5x-3025 h5WBK-30 M25x1.540 30 h5 M 30x1,5 89 89 104 104- 26 - 26
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
L53
WS3_-30 WBK-30 SBK-30 40 W5x-35
W5x-40
30 h5 WBK-35
WBK-40
40 35 h5 M 35x1,5 92
M30x1.5
50 40 h5 M 40x1,5 92
89 107
107
122
104
122
30
30
- 26
WS3_-35 Rozmerova WBK-35
tabulka opracovaniSBK-35
W5 pro ulozeni WBK 40 35 h5 M35x1.5 92 107 122 30
WS3_-40 Pro ulozeni WBK-40 SBK-40 L53 50 LZ NAZEV
Typ d0 d1 d5 L51 L52 40 h5 M40x1.5 92 Opracovani107
koncu W5 pro WBK 122 30
W5x-15 WBK-15 20 15 h5 M 15x1 81 - - 23
W5x-17 WBK-17 25 17 h5 M 17x1 81 - - 23 SIZE
JMENO DATUM A4 Standardni konce 6
W5x-20
W5x-25
WBK-20
WBK-25
25
32
20 h5
25 h5
M 20x1
M 25x1,5
81
89
-
104
-
-
23
26
NAKRESLIL Lukas 30.05.2014 SOUBOR: W5 pro WBK.dft Dimensions in [mm]
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
W5x-30 WBK-30 40 30 h5 M 30x1,5 89 104 - 26
W5x-35 WBK-35 40 35 h5 M 35x1,5 92 107 122 30
W5x-40 WBK-40 50 40 h5 M 40x1,5 92 107 122 30
NAZEV
Opracovani koncu W5 pro WBK
SIZE
JMENO DATUM A4 Standardni konce 6
NAKRESLIL Lukas 30.05.2014 SOUBOR: W5 pro WBK.dft
ZKONTROLOVAL MERITKO: HMOTNOST: SHEET 1 OF 1
INTELLIGENCE
INTELLIGENCEIN
INMOTION
MOTION
INTELLIGENCE IN MOTION
Ball
Ballscrews
screws
Accessories
Accessories
Nut
Nuthousing
7.1 Nut for
forflanged
housing
housing GFD fornuts
flanged nutsacc.
flanged DIN69501
nuts
acc. part
part5 5 part 5
acc. DIN69501
DIN69501
The
The nut
Thenut housing
housingisisissuitable
nuthousing suitable
suitablefor for assembling
forassembling flange
assemblingflange nuts
flangenuts DEB,
nutsDEB, DDB
DEB,DDB and
DDBand FSCDIN.
andFSCDIN.
FSCDIN.The
Theaxis
axis
The axis
height height
heightofofthe of
thehousingthe housing
housingisismatched is matched
matchedtotofixed to fixed
fixedbearing
bearingSFA bearing
SFAand SFA
andthe and the
thesupported
supported supported
bearing bearing SLA.
bearingSLA.
SLA.
The
Thehousing
The housingcan
housing canbebe
can bescrewed
screwedonon
screwed onfrom
fromabove
from above(S1)
above (S1)and
(S1) andbelow
and below(S2).
below (S2).
(S2).
The
Thehousing
The housingGFD-16
housing GFD-16.........5050
GFD-16 50can
canbebe
can bepinned
pinnedwith
withtwo
twotapered
taperedpins
pinsororcylindrical
cylindricalpins.
pins.
Screws
Screwsofofofstrength
Screws strengthclass
strength class8.8
class 8.8should
8.8 shouldbebe
should beused
usedfor
used forthe
for thefastening
the fastening
fastening.
GFD-12
GFD-12
GFD-12
H4H4x 45v v
x 45 L3 L3
60°60 TT
OOS1 S1H12H12 60°60° ° ,5
R 5R 5,5
=
=
G
O D1
G
D1
O
O D +1
OD
O D +1
OD
H
H
B1
B
B1
B
H2
H2
H1
H1
H5
H5
=
=
S2S2 L1 L1 LP LP
LL BB
Hole pattern 0
Ball
Ball
H1H1 DD S1 Hole
Hole
screw
screw Type
Type L L L1L1 L2L2 L3L3 HH JS7 H2H2 H3H3 H4H4 H5H5 D1D1 LPLP BB B1B1 S1 S2S2 S3S3 GG T T
Ball JS7 H8H8 H12
H12 pattern
pattern
diameter
diameter H1 D S1 Hole
screw Type L L1 L2 L3 H H2 H3 H4 H5 D1 LP B B1 S2 S3 G T
JS7 H8 H12 pattern
diameter
1212 GFD-12 6262 3636 -- 5050 3232 1717 2020 - - 1212 1212 2424 3232 8 8 3737 2222 6,66,6 M8M8 - - - - M4M4 1010
GFD-12
12 GFD-12 62 36 - 50 32 17 20 - 12 12 24 32 8 37 22 6.6 M8 - 0 M4 10
Dimensions in [mm]
GFD-16
GFD-16.........
GFD-16 5050 50
Hole
Holepattern
pattern1 1 Hole
Holepattern
pattern2 2
Ball
Ballscrew
screw
Ball
H1 D S1 Hole
Hole
Hole
screw Type
Type
Type LL L L1
L1L1 L2
L2L2 L3
L3L3 HHH H2H2 H3H3 H4H4 H5H5 D D1D1 LPLP BB B1B1 S1 S2S2 S3S3 GG T T
diameter
diameter JS7
JS7 H8
H8 H12
H12 pattern
pattern
pattern
diameter
1616 GFD-16
GFD-16 8686 5252 5252 6868 5858 3232 2222 77 1515 1515 2828 3838 1010 3737 2323 8.4
8,48,4 M10
M10 7.7
7,77,7 11 M5M5 1212
2020 GFD-20
GFD-20 9494 5252 6060 7777 6464 3434 2222 77 1717 1515 3636 4747 1616 4242 2525 8.4
8,48,4 M10
M10 7.7
7,77,7 11 M6M6 1515
2525 GFD-25
GFD-25 108
108 6565 6666 8888 7272 3939 2727 1010 1919 1818 4040 5151 1616 4646 2929 10.5
10,5
10,5 M12
M12 9.7
9,79,7 11 M6M6 1515
3232 GFD-32
GFD-32 112
112 6565 7272 9292 8282 4242 2727 1010 1919 1818 5050 6565 1616 4949 2929 10.5
10,5
10,5 M12
M12 9.7
9,79,7 11 M8M8 2020
4040 GFD-40
GFD-40 126
126 8282 8484 105
105 9797 5050 3232 1313 2323 2121 6363 7878 1616 5353 3232 12.6
12,6
12,6 M14
M14 9.7
9,79,7 22 M8M8 2020
5050 GFD-50
GFD-50 146
146 8282 104
104 125
125 115
115 6060 3232 1313 3030 2121 7575 9393 1616 5959 3434 12.6
12,6
12,6 M14
M14 9.7
9,79,7 22 M10
M10 2525
Dimensions in [mm]
KuličKové
KuličKovéšrouby
šrouby
34 / 35
BALL SCREWS
HIWIN
HIWINS.R.O.,
S.R.O.,INFO@HIWIN.CZ,
INFO@HIWIN.CZ,WWW.HIWIN.CZ
WWW.HIWIN.CZ
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
www.hIwIN.Cz
Ballscrews
Ball screws
Accessories
Accessories
7.2 Cardnic nut housings GKD for flanged nut
Cardnic nut housings for flanged nut
1616 GKD-16
GKD-16 7070 5050 1010 1515 2020 1212 2828 3838 11 M5M5 1010 0,20.2
2020 GKD-20
GKD-20 8585 5858 13.5
13,5 1717 2525 1616 3636 4747 11 M6M6 1212 0,30.3
2525 GKD-25
GKD-25 9595 6565 1515 1919 2525 1818 4040 5151 11 M6M6 1212 0,40.4
3232 GKD-32
GKD-32 125
125 8585 2020 2525 3030 2525 5050 6565 11 M8M8 1212 0,90.9
4040 GKD-40
GKD-40 140
140 100
100 2020 2929 4040 3030 6363 7878 22 M8M8 1414 1,71.7
5050 GKD-50
GKD-50 165
165 115
115 2525 3434 5050 4040 7575 9393 22 M10
M10 1616 2,62.6
Dimensions in [mm]
Dimensions in [mm]
INTELLIGENCE IN MOTION
Ball screws
Accessories
intelligence in motion
7.3 Tube connector for central lubrication system
ØD
L
H
Nominal
diameter
Type Form Thread G Tube ØD H L
of ball
screw
TCS-661 15 - 32 straight M6 6 5 23
TCS-67 40 - 80 straight M8x1 6 8 25
Dimensions in [mm]
36 / 37
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
www.hIwIN.Cz
www.hIwIN.Cz
Ball screws
Ball screws
Accessories AF
Ball
Accessories screws AD
Accessories
7.4 Spiral spring cover
Spiral spring cover
Lmin
SpiralSprings
Spiral
Spiral Springs are
springare manufacturedspecifically
cover
manufactured specificallytotosuit
suithorizontal
horizontalororvertical
verticaloperation.
operation.For
Forhorizontal
horizontal
applications,the
applications, theextension
extensionisisreduced
reduced(see
(seetabulations).
tabulations).
Spiral Springs are manufactured specifically to suit horizontal or vertical operation. For horizontal
applications,
SD theMaximum
extensionoutside
is reduced (seeoftabulations).
diameter the part to be covered
*value is reduced by 6 mm when using flanges
SDSD - Maximum outside
Maximum diameter
outsideofdiameter
the partoftothe
becovered *value
part to be is reduced by 6 mm when using flanges
covered
IDID - Inside diameter
Insideofdiameter
spiral of spiral
spring (±1 spring
mm) (±1 mm)
*value is reduced by 6 mm when using flanges
AD Outside diameter of spiral spring (±2 mm)
stroke
ADID - Outside diameter
Inside of spiral spring
diameter of spiral(±2spring
mm) (±1 mm) Lv/Lh
Lh Maximum extension length for horizontal installation position
LhAD - Maximum extension
Outside diameter of spiral springinstallation
length for horizontal (±2 mm) position
Lv Maximum extension length for vertical installation position
LvLh - Maximum extension
Maximum extension length for horizontal position
length for vertical installation installation position
BB Band width, corresponds to Lmin
BBLv - Band width,Maximum
corresponds to Lminlength for vertical installation position
extension
BB Band width, corresponds to Lmin
Installation
Installation
- Before
silver
installing the coil spring ensure that theflanges on the machine have the tolerances
-Installation
Before installing
specified in the the coil spring ensure that theflanges on the machine have the tolerances specified in
catalogue. 1/2 Lmin
-- the
Beforecoilinstalling
catalogue. the coil spring ensure that theflanges on the machine haveH the tolerancesor V
silver
The spring must be installed in accordance with the mounting label (horizontal)
specified in themust
- (vertical).When
The coil spring catalogue.
installed vertically the spring’s largermounting diameter is uppermost.or V
be installed in accordance with the mounting label H (horizontal)
- (vertical).
The coil spring
When must be installed
installed verticallyintheaccordance with mounting
spring’s larger the mounting labelisHuppermost.
diameter (horizontal) or V
-- (vertical).When
The wires must
The wires mustnot notbeberemoved
installed removed until
vertically
until after
theafter thethe
spring’s coil spring
hashas
largermounting
coil spring been
diameter
been installed
at itsatintended
is uppermost.
installed its intended SD
positionandandthetheflanges
position flangesareare about
about two twoto to three
three coilstrip
coil strip widths
widths apart.
apart.
- The wires must not be removed until after the coil spring has been installed at its intended ID
- Remove all of the wiring.
position and the flanges are about two to three coilstrip widths apart.
- After removing the wiring insert the coil spring carefully into the flange receiver. Do not let thecoil spring snap out!
- Remove all of the wiring. IF
thecoilWhen
-- Note: spring snap out!
installed coil springs must
After removing the wiring insert the coilmove
springfreely and must
carefully not flange
into the be screwed orriveted!
receiver. Do not let thecoil spring snap out!
- Note: When installed coil springs must move freely and must not be screwed orriveted!
- Note: When installed coil springs must move freely and must not be screwed orriveted!
Flanges are not part of delivery
Type SD ID AD Lh Lv BB Type SD ID AD Lh Lv BB Type SD ID AD Lh Lv BB
Flanges are not part of delivery
Rozměry
Type v tabulce
15-70-20 SD jsou15ID
11 uvedeny
AD v [mm]
22 -
Lh 70Lv 20
BB 25-450-40
Type 21
SD 25ID 48
AD 370Lh 450Lv 40
BB 30-750-50
Type 26
SD 30ID 58
AD 690Lh 750Lv 50 BB
15-100-20
15-70-20 1111 1515 2222 60- 10070 2020 25-500-40
25-450-40 2121 2525 4948 420
370 500
450 4040 30-650-60
30-750-50 2626 3030 5858 590
690 650
750 6050
Rozměry
15-120-20 v tabulce
11 jsou ID
uvedeny v [mm] 120Lv 25-450-50 30-750-60
Type
15-100-20 11 1515
SD 22
22 90Lh
AD 60 100 20
BB20 Type
25-500-40 21
SD
21 2525
ID 41
AD
49 390
Lh
420 450
Lv
500 50
BB
40 Type
30-650-60 26
SD
26 3030
ID 55
58 690
AD Lh 750
590 Lv 60
650 BB
60
15-150-20
15-70-20
15-120-20 1111 1515 2822 11090- 150 70
120 2020 25-550-50
25-450-40
25-450-50 2121 2525 4348
41 490
370
390 550
450 5040
50 30-900-60
30-750-50
30-750-60 2626 3030 5858
55 840
690 900
750 60
50
60
15-200-20
15-100-20
15-150-20 1111 1515 3122 28 160 60 200
110 100
150 2020 25-600-50
25-500-40
25-550-50 2121 2525 4449
43 540
420
490 600
500
550 5040
50 30-1000-60
30-650-60
30-900-60 2626 3030 6058 940
840 1000
590 900 6060
650
15-300-20
15-120-20
15-200-20 1111 1515 3222 31 260 90 300
160 120
200 2020 25-650-50
25-450-50
25-600-50 2121 2525 4541
44 590
390
540 650
450
600 5050 35-100-20
30-750-60
30-1000-60 3126 3530 4555
60 69060 1000
940 100
750 2060
20-100-20
15-150-20
15-300-20 1611 2015 3028 32 110 60 100
260 150
300 2020 25-750-50
25-550-50
25-650-50 2121 2525 4743
45 690
490
590 750
550
650 5050 35-100-30
30-900-60
35-100-20 3126
31 3530
35 4458
45 8406060 100
100 3060
900 20
20-150-20
15-200-20
20-100-20 1611
16 2015 20 333130 110 60 150
160 200
100 2020 25-900-50
25-600-50
25-750-50 2121 2525 5744
47 840
540
690 900
600
750 5050 35-150-30
30-1000-60
35-100-30 3126
31 3530
35 4860
44 9409060 1000
150
100 3060
30
20-200-20
15-300-20
20-150-20 1611
16 2015 20 363233 160 110 200
260 300
150 2020 30-150-30
25-650-50
25-900-50 2621 3025 3945
57 90
590
840 150
650
900 3050 35-200-30
35-100-20
35-150-30 3131 3535 5045
48 14060
90 200
150 3020
100 30
20-250-20
20-100-20
20-200-20 1616 2020 3930 36 210 60 250
160 100
200 2020 30-200-30
25-750-50
30-150-30 2621
26 3025
30 4247
39 140
690
90 200
750
150 3050
30 35-250-30
35-100-30
35-200-30 3131 3535 5244
50 190 60 250
140 200 3030
100
20-300-20
20-150-20
20-250-20 16
16 20
20 41
39 210 300
33 260
110 150
250 2020 30-250-30
25-900-50
30-200-30 2621
26 3025
30 4457
42 190
840
140 250
900
200 3050
30 35-300-30
35-150-30
35-250-30 3131 3535 5548
52 240 90 300
190 250 3030
150
20-250-30
20-200-20
20-300-20 1616 2020 3636 41 210 260 250
160 200
300 3020 30-300-30
30-150-30
30-250-30 2626 3030 4639
44 24090
190 300
150
250 3030 35-350-30
35-200-30
35-300-30 3131 3535 6150
55 290240 350
140 300 3030
200
20-300-30
20-250-20
20-250-30 1616 2020 3939 36 260 210 300250 3020
30 30-350-30
30-200-30
30-300-30 2626 3030 4942
46 290
140
240 350
200
300 3030 35-400-30
35-250-30
35-350-30 3131 3535 6352
61 340290 400
190 350 3030
250
20-350-30
20-300-20
20-300-30 1616 2020 4141 39 310 260 350300 3020
30 30-400-30
30-250-30
30-350-30 2626 3030 5044
49 340
190
290 400
250
350 3030 35-300-40
35-300-30
35-400-30 3131 3535 4855
63 240340 300
240 400 4030
300
20-400-30
20-250-30
20-350-30 1616 2020 4336 41 360 310 400
210 250
350 3030 30-450-30
30-300-30
30-400-30 2626 3030 5346
50 390
240
340 450
300
400 3030 35-350-40
35-350-30
35-300-40 3131 3535 5061
48 290240 350
290 300 4030
350 40
20-400-40
20-300-30
20-400-30 1616 2020 3539 43 360 360 400
260 300
400 4030 30-450-40
30-350-30
30-450-30 2626 3030 5349
53 370
290
390 450
350
450 4030 35-400-40
35-400-30
35-350-40 3131 3535 5463
50 340290 400
340 350 4030
400 40
20-450-40
20-350-30
20-400-40 1616 2020 4141 35 410 360 450
310 350
400 4030
40 30-500-40
30-400-30
30-450-40 2626 3030 5550
53 440
340
370 500
400
450 4030
40 35-450-40
35-300-40
35-400-40 3131 3535 5848
54 390340 450
240 400 4040
300
20-500-40
20-400-30
20-450-40 16
16 20
20 48
41 410 500
43 460
360 400
450 4030
40 30-550-40
30-450-30
30-500-40 2626 3030 5853
55 490
390
440 550
450
500 4030
40 35-500-40
35-350-40
35-450-40 3131 3535 6050
58 440390 500
290 450 4040
350
25-100-20
20-400-40
20-500-40 2116 2520 3635 48 360 60 100
460 400
500 2040 30-600-40
30-450-40
30-550-40 2626 3030 5853
58 540
370
490 600
450
550 4040 35-550-40
35-400-40
35-500-40 3131 3535 6254
60 490440 550
340 500 4040
400
25-150-20
20-450-40
25-100-20 2116
21 2520 25 384136 110 60 150
410 450
100 2040
20 30-650-40
30-500-40
30-600-40 2626 3030 6055
58 590
440
540 650
500
600 4040 35-350-50
35-450-40
35-550-40 3131 3535 5158
62 290490 350
390 550 5040
450
25-200-20
20-500-40
25-150-20 2116
21 2520 25 404838 160 110 200
460 500
150 2040
20 30-700-40
30-550-40
30-650-40 2626 3030 6458
60 640
490
590 700
550
650 4040 35-400-50
35-500-40
35-350-50 3131 3535 5260
51 340290 400
440 350 5040
500 50
25-250-20
25-100-20
25-200-20 2121 2525 4436 40 210 60 250
160 100
200 2020 30-150-50
30-600-40
30-700-40 2626 3030 4058
64 90
540
640 150
600
700 5040 35-450-50
35-550-40
35-400-50 3131 3535 5462
52 390340 450
490 400 5040
550 50
25-300-20
25-150-20
25-250-20 2121 2525 4638 44 260 210 300
110 150
250 2020 30-250-50
30-650-40
30-150-50 2626 3030 4260
40 190
590
90 250
650
150 5040
50 35-500-50
35-350-50
35-450-50 3131 3535 5551
54 440390 500
290 450 5050
350
25-300-30
25-200-20
25-300-20 2121 2525 4240 46 240 260 300
160 200
300 3020 30-350-50
30-700-40
30-250-50 2626 3030 4564
42 290
640
190 350
700
250 5040
50 35-650-50
35-400-50
35-500-50 3131 3535 6052
55 590440 650
340 500 5050
400
25-350-30
25-250-20
25-300-30 2121 2525 4544 42 290 240 350
210 250
300 3020
30 30-450-50
30-150-50
30-350-50 2626 3030 4640
45 39090
290 450
150
350 5050 35-750-50
35-450-50
35-650-50 3131 3535 6454
60 590 650 5050
690
390 750
450
25-400-30
25-300-20
25-350-30 2121 2525 4846 45 340 290 400
260 300
350 3020
30 30-550-50
30-250-50
30-450-50 2626 3030 4842
46 490
190
390 550
250
450 5050 35-850-50
35-500-50
35-750-50 3131 3535 6555
64 790690 850
440 750 5050
500
25-450-30
25-300-30
25-400-30 2121 2525 4942 48 390 340 450
240 300
400 3030 30-650-50
30-350-50
30-550-50 2626 3030 5545
48 590
290
490 650
350
550 5050 35-450-60
35-650-50
35-850-50 3131 3535 5360
65 390790 450
590 850 6050
650
25-350-30
25-450-30 21 25 45
49 290 390 350450 30 30-450-50
30-650-50 26 30 46
55 390
590 450
650 50 35-750-50
35-450-60 31 35 64
53 690390 750
450 50 60
Yellow field
25-400-30 - available
21 also
25from Stainless
48 340 400 Steel. 30 30-550-50 26 30 48 490 550 50 35-850-50 31 35 65 Dimensions
790 850in [mm]
50
Yellow field - available
25-450-30 21 also 25 from49Stainless
390 Steel.
450 30 30-650-50 26 30 55 590 650 50 35-450-60 31 35 53Dimensions
390 450in [mm]60
Ball screws
Accessories
38 / 39
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Accessories
Ball screws
Accessories
40 / 41
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Accessories
7.5 Angular contact ball bearing ZKLFA
Double-row angular contact ball bearing in O arrangement with 60° contact angle
Outer ring suitable for flange mounting
Split inner ring with defined gap for matching of preload
Lubricated for life for most applications
The ball cages are made from plastic, permissible continuous operating temperature 120 °C.
1) Contact angle a = 60°.
2) min. rs = 0.3 mm.
3) min. r1s = 0.6 mm; min. r1s = 0.3 mm.
4) Minimum diameter required of installation surface.
If these diameters are not reached, D1 and d1 should be noted.
Housing Shaft
Ball screws
Accessories
Dimensions and connecting dimensions for angular ball bearing unit ZKLFA
Bearing
Mounting bolts Axial Resistance Recommended Tightening
Shaft Axial load rating Limit speed friction
DIN 912 10.91) rigidity to tilting lock nut1) torque1)
diameter Code torque 2)
[mm]
Number C dyn Co Grease MRL CAL CKL Article MA
nxt [kN] [kN] [min-1] [Nm] [N/µm] [Nm/mrad] number [Nm]
ZKLFA0630.2Z M3 4 4.9 6.1 14000 0.01 150 4 HIR-06 2
6 ZKLFA0640.2RS M4 4 6.9 8.5 6800 0.02 200 8 HIR-06 2
ZKLFA0640.2Z M4 4 6.9 8.5 12000 0.02 200 8 HIR-06 2
ZKLFA0850.2RS M5 4 12.5 16.3 5100 0.04 250 20 HIR-08 4
8
ZKLFA0850.2Z M5 4 12.5 16.3 9500 0.04 250 20 HIR-08 4
ZKLFA1050.2RS M5 4 13.4 18.8 4600 0.06 325 25 HIR-10 6
10
ZKLFA1050.2Z M5 4 13.4 18.8 8600 0.06 325 25 HIR-10 6
ZKLFA1263.2RS M6 4 17.0 24.7 3800 0.08 375 50 HIR-12 8
12
ZKLFA1263.2Z M6 4 17.0 24.7 7600 0.08 375 50 HIR-12 8
ZKLFA1563.2RS M6 4 17.9 28.0 3500 0.10 400 65 HIR-15 10
15
ZKLFA1563.2Z M6 4 17.9 28.0 7000 0.10 400 65 HIR-15 10
The ball cages are made from plastic, permissible operating temperature 120 °C (continuous operation)
1) Tightening torque of mounting bolts according to details from manufacturer.
Screws according to DIN 912 are not supplied.
2) Bearing friction torque with gap seal (.2Z). With contact seal (.2RS) ≈ 2 × M
42 / 43
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Accessories
7.6 Angular contact ball bearing ZKLF
Double-row angular contact ball bearing in O arrangement with 60° contact angle
Outer ring suitable for flange mounting
Split inner ring with defined gap for matching of preload
Lubricated for life for most applications
Circumferential extraction slot at the outside surface of the outer ring
Radial and axial lubrication hole M6 each
Housing Shaft
Dimensions and connecting dimensions for angular ball bearing unit ZKLF
The ball cages are made from plastic, permissible operating temperature 120 °C (continuous operation)
1) Minimum diameter required of installation surface. If these diameters are not reached, D1 and d1 should be noted.
Ball screws
Accessories
ZKLF....( d <_ 50) 1) Contact angle α = 60° ZKLF....2Z ( 60 <_ d <_ 100 )
2) min. rs = 0.3 mm
3) min. r1s = 0.6 mm; min. r1s = 0.3 mm
Bearing
Mounting bolts Axial Resistance Recommended Tightening
Shaft Axial load rating Limit speed friction
DIN 912 10.91) rigidity to tilting lock nut1) torque1)
diameter Code torque 2)
[mm]
Number C dyn Co Grease MRL CAL CKL Article MA
nxt [kN] [kN] [min-1] [Nm] [N/µm] [Nm/mrad] number [Nm]
ZKLF1255.2Z M6 3 × 120° 17.0 24.7 7600 0.08 375 50 HIR-12 8
12
ZKLF1255.2RS M6 3 × 120° 17.0 24.7 3800 0.08 375 50 HIR-12 8
ZKLF1560.2Z M6 3 × 120° 17.9 28.0 7000 0.10 400 65 HIR-15 10
15
ZKLF1560.2RS M6 3 × 120° 17.9 28.0 3500 0.10 400 65 HIR-15 10
ZKLF1762.2Z M6 6 × 60° 18.8 31.0 6600 0.12 450 80 HIR-17/HIA-17 15
17
ZKLF1762.2RS M6 6 × 60° 18.8 31.0 3300 0.12 450 80 HIR-17/HIA-17 15
ZKLF2068.2Z M6 8 × 45° 26.0 47.0 5400 0.15 650 140 HIR-20/HIA-20 18
20
ZKLF2068.2RS M6 8 × 45° 26.0 47.0 3000 0.15 650 140 HIR-20/HIA-20 18
ZKLF2575.2Z M6 8 × 45° 27.5 55.0 4700 0.20 750 200 HIR-25/HIA-25 25
25
ZKLF2575.2RS M6 8 × 45° 27.5 55.0 2600 0.20 750 200 HIR-25/HIA-25 25
ZKLF3080.2Z M6 12 × 30° 29.0 64.0 4300 0.25 850 300 HIR-30/HIA-30 32
30
ZKLF3080.2RS M6 12 × 30° 29.0 64.0 2200 0.25 850 300 HIR-30/HIA-30 32
ZKLF30100.2Z M8 8 × 45° 59.0 108.0 4000 0.40 950 400 HIA-30 65
30
ZKLF30100.2RS M8 8 × 45° 59.0 108.0 2100 0.40 950 400 HIA-30 65
ZKLF3590.2Z M8 8 × 45° 41.0 89.0 3800 0.30 900 400 HIR-35/HIA-35 40
35
ZKLF3590.2RS M8 8 × 45° 41.0 89.0 2000 0.30 900 400 HIR-35/HIA-35 40
ZKLF40100.2Z M8 8 × 45° 43.0 101.0 3300 0.35 1000 555 HIR-40/HIA-40 55
40
ZKLF40100.2RS M8 8 × 45° 43.0 101.0 1800 0.35 1000 555 HIR-40/HIA-40 55
ZKLF40115.2Z M8 12 × 30° 72.0 149.0 3100 0.65 1200 750 HIA-40 110
40
ZKLF40115.2RS M8 12 × 30° 72.0 149.0 1600 0.65 1200 750 HIA-40 110
ZKLF50115.2Z M8 12 × 30° 46.5 126.0 3000 0.45 1250 1000 HIR-50/HIA-50 85
50
ZKLF50115.2RS M8 12 × 30° 46.5 126.0 1500 0.45 1250 1000 HIR-50/HIA-50 85
ZKLF50140.2Z M10 12 × 30° 113.0 250.0 2500 1.30 1400 1500 HIA-50 150
50
ZKLF50140.2RS M10 12 × 30° 113.0 250.0 1200 1.30 1400 1500 HIA-50 150
60 ZKLF60145.2Z M8 8 × 45° 84.0 214.0 2400 1.00 1300 1650 HIR-60/HIA-60 100
70 ZKLF70155.2Z M8 8 × 45° 88.0 241.0 2200 1.20 1450 2250 HIR-70/HIA-70 130
80 ZKLF80165.2Z M8 8 × 45° 91.0 265.0 2100 1.40 1575 3000 HIR-80/HIA-80 160
90 ZKLF90190.2Z M10 8 × 45° 135.0 395.0 1800 2.30 1700 4400 HIA-90 200
100 ZKLF100200.2Z M10 8 × 45° 140.0 435.0 1700 2.60 1900 5800 HIA-100 250
The ball cages are made from plastic, permissible operating temperature 120 °C (continuous operation).
1) Tightening torque of mounting bolts according to details from manufacturer.
Screws according to DIN 912 are not supplied.
2) Bearing friction torque with gap seal (.2Z). With contact seal (.2RS) ≈ 2 × MRL.
44 / 45
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Accessories
7.7 Angular contact ball bearing ZKLN
Dimensions [mm]
Weight
Shaft diameter Code
[kg] d D B rS r1S
d1 D1 Da 2) da 2)
-0.005 -0.01 -0.25 min. min.
6 ZKLN0619.2Z 0.02 6 19 12 0.3 0.3 12.0 16.5 16 9
ZKLN0624.2RS* 0.03 6 24 15 0.3 0.6 14.0 19.5 19 9
ZKLN0624.2Z 0.03 6 24 15 0.3 0.6 14.0 19.5 19 9
8 ZKLN0832.2RS 0.09 8 32 20 0.3 0.6 19.0 26.5 26 12
ZKLN0832.2Z 0.09 8 32 20 0.3 0.6 19.0 26.5 26 12
10 ZKLN1034.2RS* 0.10 10 34 20 0.3 0.6 21.0 28.5 28 14
ZKLN1034.2Z 0.10 10 34 20 0.3 0.6 21.0 28.5 28 14
12 ZKLN1242.2RS* 0.20 12 42 25 0.3 0.6 25.0 33.5 33 16
ZKLN1242.2Z 0.20 12 42 25 0.3 0.6 25.0 33.5 33 16
15 ZKLN1545.2RS* 0.21 15 45 25 0.3 0.6 28.0 36.0 35 20
ZKLN1545.2Z 0.21 15 45 25 0.3 0.6 28.0 36.0 35 20
17 ZKLN1747.2RS* 0.22 17 47 25 0.3 0.6 30.0 38.0 37 23
ZKLN1747.2Z 0.22 17 47 25 0.3 0.6 30.0 38.0 37 23
20 ZKLN2052.2RS* 0.31 20 52 28 0.3 0.6 34.5 44.0 43 25
ZKLN2052.2Z 0.31 20 52 28 0.3 0.6 34.5 44.0 43 25
25 ZKLN2557.2RS* 0.34 25 57 28 0.3 0.6 40.5 49.0 48 32
ZKLN2557.2Z 0.34 25 57 28 0.3 0.6 40.5 49.0 48 32
30 ZKLN3062.2RS* 0.39 30 62 28 0.3 0.6 45.5 54.0 53 40
ZKLN3062.2Z 0.39 30 62 28 0.3 0.6 45.5 54.0 53 40
ZKLN3072.2RS 0.72 30 72 38 0.3 0.6 51.0 65.0 64 47
ZKLN3072.2Z 0.72 30 72 38 0.3 0.6 51.0 65.0 64 47
35 ZKLN3572.2RS* 0.51 35 72 34 0.3 0.6 52.0 63.0 62 45
ZKLN3572.2Z 0.51 35 72 34 0.3 0.6 52.0 63.0 62 45
40 ZKLN4075.2RS* 0.61 40 75 34 0.3 0.6 58.0 68.0 67 50
ZKLN4075.2Z 0.61 40 75 34 0.3 0.6 58.0 68.0 67 50
ZKLN4090.2RS 0.95 40 90 46 0.6 0.6 65.0 80.0 80 56
ZKLN4090.2Z 0.95 40 90 46 0.6 0.6 65.0 80.0 80 56
50 ZKLN5090.2RS* 0.88 50 90 34 0.3 0.6 72.0 82.0 82 63
ZKLN5090.2Z 0.88 50 90 34 0.3 0.6 72.0 82.0 82 63
ZKLN50110.2RS 2.50 50 110 54 0.6 0.6 80.0 98.0 98 63
ZKLN50110.2Z 2.50 50 110 54 0.6 0.6 80.0 98.0 98 63
60 ZKLN60110.2Z 2.20 60 110 45 0.6 0.6 85.0 100 100 85
70 ZKLN70120.2Z 2.40 70 120 45 0.6 0.6 95.0 110 110 92
80 ZKLN80130.2Z 2.70 80 130 45 0.6 0.6 105.0 120 120 102
90 ZKLN90150.2Z 4.50 90 150 55 0.6 0.6 120.0 138 138 116
100 ZKLN100160.2Z 4.90 100 160 55 0.6 0.6 132.0 150 150 128
The ball cages are made from plastic, permissible operating temperature 120 °C (continuous operation).
1) Contact angle a = 60°.
2) Minimum diameter required of installation surface.
Ball screws
Accessories
Housing and shaft tolerances ZKLN...2RSPE Housing and shaft tolerances ZKLN...2RS/...2Z
3) Bearing friction torque with gap seal (.2Z). With seal disc (.2RS) ≈ 2 × M .
4) Lock nuts are not supplied; order separately!
46 / 47
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Accessories
12
0°
t
d2
d3
d1
0,5 A
0,01 A h
Grub screw
Screw max.
tightening
Type Thread D h g t d1 c m
torque
[Nm]
HIR-08 M8×0.75 16 8 3 2.0 11 4 M4 2.6
HIR-10 M10×0.75 18 8 3 2.0 13 4 M4 2.6
HIR-12 M12×1.00 22 8 3 2.0 18 4 M4 2.6
HIR-15 M15×1.00 25 8 3 2.0 21 4 M4 2.6
HIR-17 M17×1.00 28 10 4 2.0 23 5 M5 5.0
HIR-20 M20×1.00 32 10 4 2.0 27 5 M5 5.0
HIR-20 × 1.5 M20×1.50 32 10 4 2.0 27 5 M5 5.0
HIR-25 M25×1.50 38 12 5 2.0 33 6 M6 9.0
HIR-30 M30×1.50 45 12 5 2.0 40 6 M6 9.0
HIR-35 M35×1.50 52 12 5 2.0 47 6 M6 9.0
HIR-40 M40×1.50 58 14 6 2.5 52 7 M6 9.0
HIR-45 M45×1.50 65 14 6 2.5 59 7 M6 9.0
HIR-50 M50×1.50 70 14 6 2.5 64 7 M6 9.0
HIR-55 M55×2.00 75 16 7 3.0 68 8 M6 9.0
HIR-60 M60×2.00 80 16 7 3.0 73 8 M6 9.0
HIR-65 M65×2.00 85 16 7 3.0 78 8 M6 9.0
HIR-70 M70×2.00 92 18 8 3.5 85 9 M8 22.0
HIR-75 M75×2.00 98 18 8 3.5 90 9 M8 22.0
HIR-80 M80×2.00 105 18 8 3.5 95 9 M8 22.0
HIR-85 M85×2.00 110 18 8 3.5 102 9 M8 22.0
HIR-90 M90×2.00 120 20 10 4.0 108 10 M8 22.0
HIR-95 M95×2.00 125 20 10 4.0 113 10 M8 22.0
HIR-100 M100×2.00 130 20 10 4.0 120 10 M8 22.0
Dimensions in [mm]
INTELLIGENCE IN MOTION
Ball screws
Accessories
c
b
12
0°
d5
d4
d2
d3
d1
t
0,5 A
0,002 A h
Grub screw
Screw max.
tightening
Type Thread D h g t d1 A m
torque
[Nm]
HIA-17 M17×1.0 28 16 4 2.0 23 22.5 M4 1.8
HIA-20 M20×1.0 32 16 4 2.0 27 26.0 M4 1.8
HIA-20 × 1.5 M20×1.5 32 16 4 2.0 27 26.0 M4 1.8
HIA-25 M25×1.5 38 18 5 2.0 33 31.5 M5 3.5
HIA-30 M30×1.5 45 18 5 2.0 40 37.5 M5 3.5
HIA-35 M35×1.5 52 18 5 2.0 47 43.5 M5 3.5
HIA-40 M40×1.5 58 20 6 2.5 52 49.0 M6 6.3
HIA-45 M45×1.5 65 20 6 2.5 59 55.0 M6 6.3
HIA-50 M50×1.5 70 20 6 2.5 64 60.0 M6 6.3
HIA-55 M55×2.0 75 22 7 3.0 68 65.0 M6 6.3
HIA-60 M60×2.0 80 22 7 3.0 73 70.0 M6 6.3
HIA-65 M65×2.0 85 22 7 3.0 78 75.0 M6 6.3
HIA-70 M70×2.0 92 24 8 3.5 85 81.0 M8 15.0
HIA-75 M75×2.0 98 24 8 3.5 90 87.0 M8 15.0
HIA-80 M80×2.0 105 24 8 3.5 95 93.0 M8 15.0
HIA-85 M85×2.0 110 24 8 3.5 102 98.0 M8 15.0
HIA-90 M90×2.0 120 26 10 4.0 108 105.0 M8 15.0
HIA-95 M95×2.0 125 26 10 4.0 113 110.0 M8 15.0
HIA-100 M100×2.0 130 26 10 4.0 120 115.0 M8 15.0
Dimensions in [mm]
48 / 49
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
www.hiwin.cz
Ball screws
Ball screws
Project planning
Project planning sheet sheet
Customer Data
Company: Contact Person:
Department:
Phone:
Project: Fax:
Email:
Cycle data
Phase Direction of mo- Process force Acceleration Deceleration Rotation speed [1/min] Time slice
n tion, see (1) (±) FP [N], see (2) a [m/s²] a [m/s²] n1 n2 [%]
1
2
3
4
Other notes
intelLigence in motion
Notes:
50 / 51
BALL SCREWS
hiwin s.r.o., info@hiwin.cz, www.hiwin.cz
intelligence IN MOTION
HIWIN s.r.o.
Medkova 888/11
627 00 Brno
CZECH REPUBLIC
Tel.: +420 548 528 238
Fax.: +420 548 220 223
Email: INFO@hiwin.cz
www.hiwin.CZ
01 02 03 04
HIWIN S.R.O.
MLÁDEŽNÍCKA 2101
01701 POVÁŽSKÁ BYSTRICA
SLOVENSKO
TEL.: +421 424 434 777
www.hiwin.sk
FAX.: +421 424 262 306
EMAIL: INFO@HIWIN.SK
WWW.HIWIN.SK
Bulgaria
Tel.: +359-2 974 5659
Fax.: +359-2 974 5659
Email: info@hiwin.bg
05
WWW.HIWIN.CZ
06
WWW.HIWIN.CZ
07
WWW.HIWIN.CZ
09
08
WWW.HiWin.cZ
WWW.HIWIN.CZ
www.hiwin.bg
Technical data subject to change without notice
© Hiwin s.r.o. 2016