Beruflich Dokumente
Kultur Dokumente
ANNEXURE A
TYPICAL DESIGN OF FOUNDATION
PMC:
PROJECT : Foundation Design
INDEX
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
1.1 SCOPE
1.2 DESIGN PHILOSOPHY
1.3 DESIGN SPECIFICATION , CODES AND STANDARDS
1.4 UNITS OF MEASUREMENT
1.5 MATERIALS
1.6 LEGENDS
2.0 FOOTING
PMC:
PROJECT : Foundation Design
1.1 SCOPE
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
The scope of the present report is to analyse and design the foundations for Pipe Support AX1-001 TO 004
2) The footing has been designed for vertical loads and moments in X/Z dir and Y- dir.
1.5 MATERIALS
Concrete
Characteristic Strength of Concrete fck = 30 N/mm2
Specific weight gc = 25 kN/m3
Reinforcement
Yield Strength of High Yield Strength Deformed bars (HYSD)
in accordance with Table 1 of IS:1786, (Grade - Fe415) fy = 415 N/mm2
Soil data
Specific weight (dry) gs = 18 kN/m3
Internal friction angle f = 30 0
Co-efficient of Friction m = 0.40
(Between the Soil Materials and Footing Bottom Concrete)
Allowable net pressure of Soil at 1 m below Natural Grade Level (NGL),
For Normal Operating Case qsoil net = 35 kN/m2
For Operation with Wind (35 X 1.25) q soil wind = 43.75 kN/m2
For Operation with Earthquake (35 X 1.25) qsoil Seismic = 43.75 kN/m2
(Refer Table 1 of IS 1893(Part 1)-2002)
For Maintenance load (35 X 1.2) qsoil test = 42 kN/m2
(As per IS : 456-2000 allowable net soil bearing pressure can be increased by 25% for
combination with wind, 25% for earthquake and 20% for testing loads )
PMC:
Specific weight
PROJECT : Foundation Design
=
10
CRUDE AND FINISHED PRODUCTS TANKAGES
kN/m3
OWNER :
PMC: PROJECT : Foundation Design OWNER :
1.6 LEGENDS
fck Characteristic Strength of Concrete
gc Specific weight of Concrete
fy
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
PMC:
PROJECT : Foundation Design
2.0 FOOTING
2.1 GENERAL GEOMETRY
2.1.1 FOUNDATION DIMENSIONS Dx
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
X (T)
LX
Dimensions
Dx = 1.10 m Pedestal Length along X
Dz = 1.10 m Pedestal Length along Z
LX = 7.90 m Foundation Length along X
LZ = 7.90 m Foundation Length along Z
T = 0.30 m Thickness of Foundation
H = 1.00 m Depth of Foundation
HS = 0.30 m Projection above FGL
h = H + HS = 1.30 m
h1 = h-T = 1.00 m Height of Pedestal
FGL = 99.85 m
HPP = 100.00 m
98.850
300
X(T)
7900
7900
Z (L)
1100
FGL
10 mm Dia @
200 mm c /c long bars 10 mm Dia @
200 mm c /c transverse bars
12 mm Dia @ 12 mm Dia @
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
This document is exclusive property of IOT DESIGN & ENGINEERING Limit
PMC:
200
mm c/c
long bars
PROJECT : Foundation Design
200
CRUDE AND FINISHED PRODUCTS TANKAGES
mm c /c transverse bars
OWNER :
PMC: PROJECT : Foundation Design OWNER :
F1 101 7.9 7.9 0.3 #N/A #N/A 0 0.00 #N/A #N/A #N/A #N/A
or used
copied or in anyway
used in detrimental to
anyway detrimental the interest
to the of this
interest of company and
this company subject to
and subject return on
to return
q max3 = Allowable bearing pressure for earthquake, q max4 = Allowable bearing pressure for maintenance load
and must
lent and
Mark
m m m Flexure mm2 Shear mm2.
the purpose
F1 101 7.9 7.9 0.3 #N/A #N/A #N/A #N/A #N/A #N/A #N/A
exclusive property
document isis exclusive of IOT
property of ENGINEERING Limited.
DESIGN && ENGINEERING
IOT DESIGN be used
to be
Limited. ItIt isis to for the
only for
used only
PMC:
PROJECT : Foundation Design
Required Z (L)
FOOTING Provided Reinforcement Check
demand
Rein.
returntoonreturn
7.9
AstBL #N/A 12 Ф @ 200 mm c/c = 565.5 ###
subject
F1
and subject
PMC:
PROJECT : Foundation Design
Hx P(Hy) Hz Mx My Mz
Sr.No. Load Combination
kN kN kN kN-m kN-m kN-m
1 101 #N/A #N/A #N/A #N/A 0.00 #N/A
2 102 #N/A #N/A #N/A #N/A 0.00 #N/A
3 103 #N/A #N/A #N/A #N/A 0.00 #N/A
4 104 #N/A #N/A #N/A #N/A 0.00 #N/A
5 105 #N/A #N/A #N/A #N/A 0.00 #N/A
6 106 #N/A #N/A #N/A #N/A 0.00 #N/A
7 107 #N/A #N/A #N/A #N/A 0.00 #N/A
8 108 #N/A #N/A #N/A #N/A 0.00 #N/A
9 109 #N/A #N/A #N/A #N/A 0.00 #N/A
PMC:
FOS, sliding
B. Stability Check
Pb
ms
=
= P+DL
PROJECT : Foundation Design
0.4
= m x Ps / Sqrt(Hx2 + Hz2)
CRUDE AND FINISHED PRODUCTS TANKAGES
101B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 60.00 #N/A 1.55 #N/A 1.55
102B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 60.00 #N/A 1.55 #N/A 1.55
103B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 60.00 #N/A 1.55 #N/A 1.55
104B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 60.00 #N/A 1.55 #N/A 1.55
105B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
106B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
107B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
108B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
109B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
This document is exclusive property of IOT DESIGN & ENGINEERING Limit
Critical values
#N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
Minimum contact area is in loadcase ### which has maximum eccentricity ratio.
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
PMC: PROJECT : Foundation Design OWNER :
x
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
4Cz qz
Neutral Axis
Lz
ez
Cz Z
qmax Cx ex
P
Lx
qsz
qsx 4Cx qx
Contact Area Calculations
Cx = (Lx/2 - ex)
Cz = (Lz/2 - ez)
Case i) If (ex/Lx+ez/Lz) <1/6, Full contact
Case ii) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx>0.25 & ez/Lz>0.25 Case ii)
Contact area is 8*(Cx)*(Cz)
Case iii) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx<0.25 & ez/Lz<0.25
X = (4Cz-Lz)*Cx/Cz Case iii)
Z = (4Cx-Lx)*Cz/Cx
Contact area is = (Af-(Lz-Z)*(Lx-X)/2)
Case iv) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx>0.25 & ez/Lz<0.25 Case iv)
X = (4Cz-Lz)*Cx/Cz
Contact area is = Lz*(4Cx+X)/2
Case v) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx<0.25 & ez/Lz>0.25
Z = (4Cx-Lx)*Cz/Cx Case v)
Contact area is = Lx*(4Cz+Z)/2
FUF
MUZ VUX
s min
s max
PMC:
ZZZ
PROJECT : Foundation Design
= 82.17
= (LZLX2/6)
m3
CRUDE AND FINISHED PRODUCTS TANKAGES
qL1
ON BUILD-OWN-OPERATE-TRANSFER (BOOT) BASIS
INSTALLATION, OPERATION AND MAINTENANCE OF
qTC
qmax
PMC: PROJECT : Foundation Design OWNER :
PMC:
PROJECT : Foundation Design
Critical Values
eZ/LZ
Load sV sml smt eZ eX ez/LZ eX/LX CZ CX qmax qT1 qmin qL1
on demand
+ K factor
Case
eX/LX
on demand
201 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
to return
202 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
to return
203 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
204 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
subject
205 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
subject
#N/A
and and
206 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
207 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
company
208 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
company
209 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
the purpose
for purpose
for the it is lent
which
which mustmust
and and
it is lent be copied
notcopied
not be in anyway
or used
or used detrimental
detrimental
in anyway the interest
to interest
to the of this
of this
WL
Limited.
Maximum Pressure Gross at face of pedestal in longitudinal qLC = qT1+ [(qmax - qT1)((LZ+Dz)/2)/min(LZ,4Cz)]
Limited.
Maximum Pressure Gross at face of pedestal in transverse qTC = qL1+ [(qmax - qL1)((LX+Dx)/2)/min(LX,4Cx)]
direction if (Lx+Dx)/2<min(Lx,4cx) Else 0
MUBL =
DESIGN
Pressure at distance "d" from face of pedestal in longitudinal qLd = qT1 + [(qmax - qT1)(LZ-LCL+d)/min(LZ,4Cz)]
direction if (Lz-Lcl+d)/2<min(Lz,4CZ) Else 0
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
PMC: PROJECT : Foundation Design OWNER :
Pressure at distance "d" from face of pedestal in transverse qTd = qL1 + [(qmax - qL1)(LX-LCT+d)/min(LX,4CX)]
direction if (Lx-LcT+d)/2<min(Lx,4Cx) Else 0
Where d = Effective Depth of Footing
VUL =
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
Shear at "d" from face of Pedestal in longitudinal direction [(LCL-d) x qLD + 0.5 x (qmax-WL - qLd) x (LCL-d)]
VUT =
Shear at "d" from face of Pedestal in transverse direction [(LCT-d) x qTD + 0.5 x (qmax -WL - qTd) x (LTL-d)]
Critical Values
Load qmax (net) qTC qLC MUBL MUBT MUTL MUTT qLD qTD VUL VUT
WL
Case
201 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
202 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
203 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
204 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
205 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
206 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
207 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
208 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
209 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
Bottom Reinforcement
Longitudinal Direction
Where,
Mu
Ast reqd =
0.87 Fy . j .d
Partial Safety Factor for Steel
j=0 .5+ 0. 25−
√
j =
gs =
#N/A
1.150
M
0 .87 fck . b . d . d
(Refer Cl. 36.4.2 of IS 456 - 2000)
Top Reinforcement:
Longitudinal Direction
Where,
Mu
This document is exclusive property of IOT DESIGN & ENGINEERING Limited. It is to be used only for the purpose which it is lent and must not be copied or used in anyway detrimental to the interest of this company and subject to return on demand
Ast reqd =
0.87 Fy . j .d
Partial Safety Factor for Steel
j=0 .5+ 0. 25−
gs =
√
j =
1.15
#N/A
M
0 .87 fck . b . d . d
(Refer Cl. 36.4.2 of IS 456 - 2000)
Design Strength of Steel fd = Yeild Strength / Partial Safety Factor
= 0.87 fy
Flexural reinforcement reuired Ast flex = #N/A mm2 ------------------ A
Percentage of Steel required r = #N/A %
Minimum area of reinforcement r min = 0.12 % of Gross cross sectional area
(Refer Cl. 26.5.2.1 of IS 456- 2000)
Ast min = 360 mm2 ------------------ B
Area of Steel required is maximum of A & B
Ast reqd = #N/A mm2 ###
PMC:
PROJECT : Foundation Design
= 1.77 m2
and subject
= 0.60
(Refer Cl. 31.3.3 of IS 456 - 2000)
anyway detrimental
= #N/A N/mm2
must not
Permissible Shear Stress (tcp) = ks tc (Refer Cl. 31.6.3.1 & Cl. 34.2.4.1.b of IS :
and must
456 - 2000)
ks = 0.5 + bc
lent and
Where, < 1
bc = Ratio of short to long side of column
is lent
= DZ / DX = 1.00
which itit is
Therefore, ks = 1.000
the purpose
tc = 0.25 x Sqrt(fck)
= 1.370 N/mm2
for the
= 1.370 N/mm2
used only
PMC:
PROJECT : Foundation Design
ANNEXURE A
INDEX
1.1 SCOPE
1.2 DESIGN PHILOSOPHY
1.3 DESIGN SPECIFICATION , CODES AND STANDARDS
1.4 UNITS OF MEASUREMENT
1.5 MATERIALS
1.6 REFERENCE DRAWINGS
1.7 LEGENDS
1.1 SCOPE
The scope of the present report is to analyse and design the foundations for Structure -Crude Pump House
2) The footing has been designed for vertical loads and moments in X/Z dir and Y- dir.
3. IS: 1893 - 2005 (Part 4) Industrial Structures including Stack like Structures.
4. IS: 13920 - 1993 Ductile Detailing of Reinforced Concrete Structures Subjected to Seismic Forces
Project Standard Drawings and Specification
5 PDRP-8310-DI-000-0001 Design Basis
6 PDRP-8310-43-201-0003 Civil and Structural Steel Works General Notes.
7 3210-8310-SP-0005 General Specification for Concrete Work
8 3210-8330-SP-0020 Buildings Performancr Specification
1.5 MATERIALS
Concrete
Characteristic Strength of Concrete (M25) fck = 30 N/mm2
Specific weight gc = 25 kN/m3
Reinforcement
Yield Strength of High Yield Strength Deformed bars (HYSD)
in accordance with Table 1 of IS:1786, (Grade - Fe415) fy = 415 N/mm2
Soil data
Specific weight (dry) gs = 18 kN/m3
Internal friction angle f = 30 0
PMC: PROJECT : 101 OWNER :
1.7 LEGENDS
fck Characteristic Strength of Concrete
gc Specific weight of Concrete
fy Yield Strength of High Yield Strength Deformed bars (HYSD)
gw Specific weight of Water
Wbf Weight of Water
gs Specific weight of Soil
f Internal friction angle of soil
m Co-efficient of Friction between soil and concrete
qsoil net Allowable Net Pressure of Soil (Normal Operating Case)
qsoil wind Allowable Net Pressure of Soil (Operating Case with Wind)
qsoil Seismic Allowable Net Pressure of Soil (Operating Case with Seismic)
qsoil test Allowable Net Pressure of Soil (Test / Erection Case)
Dx Size of column along X
Dz Size of column along Z
T Thickness of Footing
D Height of Soil above Foundation
Lx Foundation Length along X
Lz Foundation Length along Z
H Depth of Foundation
h5 Height of Soil for Stability Check
Ap Area of Column
Af Area of Foundation
Wf Weight of Foundation Slab
Ws Weight of Soil
DL Total Dead Load of Foundation
Ix,Iy Moment of Inertia of the leg along x and y directions
Hx,Hy,Hz Loads along x,y,z directions respectively
Mx,My,Mz Moments along x,y,z directions respectively
P Total Vertical Load
Ws(stab) Weight of Soil for Stability Check
DLS Total Dead Load of Foundation for Stability Calculation
Mo Overturning Moment
Mr Resisting Moment
b0 Perimeter for Punching Shear Check
tv Nominal Shear Stress
tvp Nominal Punching Shear Stress
tcp Permissible Shear Stress
qsx, qsz Base pressure at Shear Critical section
qx, qz Base pressure at corners of footing alogn x and z
Cx, Cz Intercepts of zero pressure line during redistribution
PMC: PROJECT : 101 OWNER :
2.0 FOOTING - F1
2.1 GENERAL GEOMETRY
2.1.1 FOUNDATION DIMENSIONS Dx
X (T)
LX
Dimensions
Dx = 0.90 m Pedestal Length along X
Dz = 0.90 m Pedestal Length along Z
LX = 7.90 m Foundation Length along X
LZ = 7.90 m Foundation Length along Z
T = 0.30 m Thickness of Foundation
H = 1.00 m Depth of Foundation
HS = 0.30 m Projection above HPP
h = H1 + HS = 1.30 m
h1 = h-T = 1.00 m Height of Pedestal
FGL = 99.85 m
HPP = 100.00 m
98.850
300
PMC: PROJECT : 101 OWNER :
Z (L)
900
FGL
12 mm Dia @
200 mm c /c long bars 12 mm Dia @
200 mm c /c transverse bars
20 mm Dia @ 20 mm Dia @
200 mm c/c long bars 200 mm c /c transverse bars
113 #N/A #N/A #N/A #N/A #N/A #N/A #N/A 42.00 #N/A 5.55 #N/A 5.55
114 #N/A #N/A #N/A #N/A #N/A #N/A #N/A 3500.00 #N/A 6.55 #N/A 6.55
115 #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 7.55 #N/A 7.55
116 #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 7.55 #N/A 7.55
117 #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 7.55 #N/A 7.55
118 #N/A #N/A #N/A #N/A #N/A #N/A #N/A 10.00 #N/A 7.55 #N/A 7.55
119 #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 7.55 #N/A 7.55
120 #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 7.55 #N/A 7.55
101B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 61.75 #N/A 1.55 #N/A 1.55
102B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 61.75 #N/A 1.55 #N/A 1.55
103B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 61.75 #N/A 1.55 #N/A 1.55
104B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 61.75 #N/A 1.55 #N/A 1.55
105B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
106B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
107B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
108B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
109B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
110B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 52.75 #N/A 1.55 #N/A 1.55
111B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 44.27 #N/A 1.55 #N/A 1.55
112B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 1.55 #N/A 1.55
113B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 42.00 #N/A 1.55 #N/A 1.55
114B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 3500.00 #N/A 1.55 #N/A 1.55
115B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 1.55 #N/A 1.55
116B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 1.55 #N/A 1.55
117B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 1.55 #N/A 1.55
118B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 10.00 #N/A 1.55 #N/A 1.55
119B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 1.55 #N/A 1.55
120B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 0.00 #N/A 1.55 #N/A 1.55
Critical values
#N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
Minimum contact area is in loadcase ### which has maximum eccentricity ratio.
4Cz qz
Neutral Axis
Lz
ez
Cz P Z
qsz
qmax Cx ex
qsx qx
Lx
PMC: PROJECT : 101 OWNER :
4Cx
Cx = (Lx/2 - ex)
Cz = (Lz/2 - ez)
Case i) If (ex/Lx+ez/Lz) <1/6, Full contact
Case ii) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx>0.25 & ez/Lz>0.25 Case ii)
Contact area is 8*(Cx)*(Cz)
Case iii) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx<0.25 & ez/Lz<0.25
X = (4Cz-Lz)*Cx/Cz Case iii)
Z = (4Cx-Lx)*Cz/Cx
Contact area is = (Af-(Lz-Z)*(Lx-X)/2)
Case iv) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx>0.25 & ez/Lz<0.25 Case iv)
X = (4Cz-Lz)*Cx/Cz
Contact area is = Lz*(4Cx+X)/2
Case v) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx<0.25 & ez/Lz>0.25
Z = (4Cx-Lx)*Cz/Cx Case v)
Contact area is = Lx*(4Cz+Z)/2
FUF
MUZ VUX
s min
s max
Pressure due to Transverse Moment (MX) smt = [MX / ZXX] qmin qT1
Area A = (LX x LZ)
= 62.41 m2
Section Modulus ZXX = (LXLZ2/6) qLC
= 82.17 m3
qL1 qTC qmax
ZZZ = (LZLX2/6)
= 82.17 m3
Critical Values
eZ/LZ
Load sV sml smt eZ eX ez/LZ eX/LX CZ CX qmax qT1 qmin qL1
+ K factor
Case
eX/LX
201 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
PMC: PROJECT : 101 OWNER :
202 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
203 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
204 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
205 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
206 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
207 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
208 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
209 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
210 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
211 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
212 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
213 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
214 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
215 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
216 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
217 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
218 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
219 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
220 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
Maximum Pressure Gross at face of pedestal in transverse qTC = qL1+ [(qmax - qL1)((LX+Dx)/2)/min(LX,4Cx)]
direction if (Lx+Dx)/2<min(Lx,4cx) Else 0
For calculating Ultimate Top Moment in base slab average base presuure distribution is considered below the base slab in
longitudinal direction
MUTT = (WL x LCT2/2)
Ultimate Top Moment for base slab
MUTL = (WL x LCL2/2) For Uplift Condition only
Pressure at distance "d" from face of pedestal in longitudinal qLd = qT1 + [(qmax - qT1)(LZ-LCL+d)/min(LZ,4Cz)]
direction if (Lz-Lcl+d)/2<min(Lz,4CZ) Else 0
PMC: PROJECT : 101 OWNER :
Pressure at distance "d" from face of pedestal in transverse qTd = qL1 + [(qmax - qL1)(LX-LCT+d)/min(LX,4CX)]
direction if (Lx-LcT+d)/2<min(Lx,4Cx) Else 0
Where d = Effective Depth of Footing
VUL =
Shear at "d" from face of Pedestal in longitudinal direction [(LCL-d) x qLD + 0.5 x (qmax-WL - qLd) x (LCL-d)]
VUT =
Shear at "d" from face of Pedestal in transverse direction [(LCT-d) x qTD + 0.5 x (qmax -WL - qTd) x (LTL-d)]
Critical Values
Load qmax (net) qTC qLC MUBL MUBT MUTL MUTT qLD qTD VUL VUT
WL
Case
201 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
202 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
203 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
204 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
205 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
206 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
207 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
208 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
209 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
210 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
211 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
212 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
213 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
214 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
215 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
216 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
217 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
218 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
219 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
220 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
Partial Safety Factor for Steel gs = 1.15 (Refer Cl. 36.4.2 of IS 456 -2000)
Top Reinforcement:
Longitudinal Direction
Where,
Mu
Ast reqd =
0.87 Fy . j .d
j =0 .5+ 0. 25−
gs =
√
j =
M
0 .87 fck . b . d . d
#N/A
Partial Safety Factor for Steel 1.15 (Refer Cl. 36.4.2 of IS 456 - 2000)
Design Strength of Steel fd = Yeild Strength / Partial Safety Factor
= 0.87 fy
Flexural reinforcement reuired Ast flex = #N/A mm2 ------------------ A
Percentage of Steel required r = #N/A %
Minimum area of reinforcement r min = 0.12 % of Gross cross sectional area
(Refer Cl. 26.5.2.1 of IS 456- 2000)
Ast min = 360 mm2 ------------------ B
Area of Steel required is maximum of A & B
Ast reqd = #N/A mm2 ###
Therefore, ks = 1.000
tc = 0.25 x Sqrt(fck)
= 1.370 N/mm2
Permissible Shear Stress (tcp) = 1 x 1.37
= 1.370 N/mm2
tvp ### tcp ###
###
###
PMC: PROJECT : 102 OWNER :
ANNEXURE A
INDEX
1.1 SCOPE
1.2 DESIGN PHILOSOPHY
1.3 DESIGN SPECIFICATION , CODES AND STANDARDS
1.4 UNITS OF MEASUREMENT
1.5 MATERIALS
1.6 REFERENCE DRAWINGS
1.7 LEGENDS
1.1 SCOPE
The scope of the present report is to analyse and design the foundations for Structure -Crude Pump House
2) The footing has been designed for vertical loads and moments in X/Z dir and Y- dir.
3. IS: 1893 - 2005 (Part 4) Industrial Structures including Stack like Structures.
4. IS: 13920 - 1993 Ductile Detailing of Reinforced Concrete Structures Subjected to Seismic Forces
Project Standard Drawings and Specification
5 PDRP-8310-DI-000-0001 Design Basis
6 PDRP-8310-43-201-0003 Civil and Structural Steel Works General Notes.
7 3210-8310-SP-0005 General Specification for Concrete Work
8 3210-8330-SP-0020 Buildings Performancr Specification
1.5 MATERIALS
Concrete
Characteristic Strength of Concrete (M25) fck = 30 N/mm2
Specific weight gc = 25 kN/m3
Reinforcement
Yield Strength of High Yield Strength Deformed bars (HYSD)
in accordance with Table 1 of IS:1786, (Grade - Fe415) fy = 415 N/mm2
Soil data
Specific weight (dry) gs = 18 kN/m3
Internal friction angle f = 30 0
PMC: PROJECT : 102 OWNER :
1.7 LEGENDS
fck Characteristic Strength of Concrete
gc Specific weight of Concrete
fy Yield Strength of High Yield Strength Deformed bars (HYSD)
gw Specific weight of Water
Wbf Weight of Water
gs Specific weight of Soil
f Internal friction angle of soil
m Co-efficient of Friction between soil and concrete
qsoil net Allowable Net Pressure of Soil (Normal Operating Case)
qsoil wind Allowable Net Pressure of Soil (Operating Case with Wind)
qsoil Seismic Allowable Net Pressure of Soil (Operating Case with Seismic)
qsoil test Allowable Net Pressure of Soil (Test / Erection Case)
Dx Size of column along X
Dz Size of column along Z
T Thickness of Footing
D Height of Soil above Foundation
Lx Foundation Length along X
Lz Foundation Length along Z
H Depth of Foundation
h5 Height of Soil for Stability Check
Ap Area of Column
Af Area of Foundation
Wf Weight of Foundation Slab
Ws Weight of Soil
DL Total Dead Load of Foundation
Ix,Iy Moment of Inertia of the leg along x and y directions
Hx,Hy,Hz Loads along x,y,z directions respectively
Mx,My,Mz Moments along x,y,z directions respectively
P Total Vertical Load
Ws(stab) Weight of Soil for Stability Check
DLS Total Dead Load of Foundation for Stability Calculation
Mo Overturning Moment
Mr Resisting Moment
b0 Perimeter for Punching Shear Check
tv Nominal Shear Stress
tvp Nominal Punching Shear Stress
tcp Permissible Shear Stress
qsx, qsz Base pressure at Shear Critical section
qx, qz Base pressure at corners of footing alogn x and z
Cx, Cz Intercepts of zero pressure line during redistribution
PMC: PROJECT : 102 OWNER :
2.0 FOOTING - F1
2.1 GENERAL GEOMETRY
2.1.1 FOUNDATION DIMENSIONS Dx
X (T)
LX
Dimensions
Dx = 0.65 m Pedestal Length along X
Dz = 0.65 m Pedestal Length along Z
LX = 7.90 m Foundation Length along X
LZ = 7.90 m Foundation Length along Z
T = 0.30 m Thickness of Foundation
H = 1.00 m Depth of Foundation
HS = 0.30 m Projection above HPP
h = H1 + HS = 1.30 m
h1 = h-T = 1.00 m Height of Pedestal
FGL = 99.85 m
HPP = 100.00 m
98.850
300
PMC: PROJECT : 102 OWNER :
Z (L)
650
FGL
12 mm Dia @
200 mm c /c long bars 12 mm Dia @
200 mm c /c transverse bars
16 mm Dia @ 16 mm Dia @
200 mm c/c long bars 200 mm c /c transverse bars
101B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 61.75 #N/A 1.55 #N/A 1.55
102B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 61.75 #N/A 1.55 #N/A 1.55
103B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 61.75 #N/A 1.55 #N/A 1.55
104B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 61.75 #N/A 1.55 #N/A 1.55
105B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
106B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
107B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
108B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
109B #N/A #N/A #N/A #N/A #N/A #N/A #N/A 53.00 #N/A 1.55 #N/A 1.55
Critical values
#N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
Minimum contact area is in loadcase ### which has maximum eccentricity ratio.
4Cz qz
Neutral Axis
Lz
ez
Cz P Z
qsz
qmax Cx ex
qsx qx
Lx
PMC: PROJECT : 102 OWNER :
4Cx
Cx = (Lx/2 - ex)
Cz = (Lz/2 - ez)
Case i) If (ex/Lx+ez/Lz) <1/6, Full contact
Case ii) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx>0.25 & ez/Lz>0.25 Case ii)
Contact area is 8*(Cx)*(Cz)
Case iii) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx<0.25 & ez/Lz<0.25
X = (4Cz-Lz)*Cx/Cz Case iii)
Z = (4Cx-Lx)*Cz/Cx
Contact area is = (Af-(Lz-Z)*(Lx-X)/2)
Case iv) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx>0.25 & ez/Lz<0.25 Case iv)
X = (4Cz-Lz)*Cx/Cz
Contact area is = Lz*(4Cx+X)/2
Case v) If (ex/Lx+ez/Lz) >1/6 and if ex/Lx<0.25 & ez/Lz>0.25
Z = (4Cx-Lx)*Cz/Cx Case v)
Contact area is = Lx*(4Cz+Z)/2
FUF
MUZ VUX
s min
s max
Pressure due to Transverse Moment (MX) smt = [MX / ZXX] qmin qT1
Area A = (LX x LZ)
= 62.41 m2
Section Modulus ZXX = (LXLZ2/6) qLC
= 82.17 m3
qL1 qTC qmax
ZZZ = (LZLX2/6)
= 82.17 m3
Critical Values
eZ/LZ
Load sV sml smt eZ eX ez/LZ eX/LX CZ CX qmax qT1 qmin qL1
+ K factor
Case
eX/LX
201 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
PMC: PROJECT : 102 OWNER :
202 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
203 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
204 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
205 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
206 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
207 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
208 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
209 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
Maximum Pressure Gross at face of pedestal in transverse qTC = qL1+ [(qmax - qL1)((LX+Dx)/2)/min(LX,4Cx)]
direction if (Lx+Dx)/2<min(Lx,4cx) Else 0
For calculating Ultimate Top Moment in base slab average base presuure distribution is considered below the base slab in
longitudinal direction
MUTT = (WL x LCT2/2)
Ultimate Top Moment for base slab
MUTL = (WL x LCL2/2) For Uplift Condition only
Pressure at distance "d" from face of pedestal in longitudinal qLd = qT1 + [(qmax - qT1)(LZ-LCL+d)/min(LZ,4Cz)]
direction if (Lz-Lcl+d)/2<min(Lz,4CZ) Else 0
PMC: PROJECT : 102 OWNER :
Pressure at distance "d" from face of pedestal in transverse qTd = qL1 + [(qmax - qL1)(LX-LCT+d)/min(LX,4CX)]
direction if (Lx-LcT+d)/2<min(Lx,4Cx) Else 0
Where d = Effective Depth of Footing
VUL =
Shear at "d" from face of Pedestal in longitudinal direction [(LCL-d) x qLD + 0.5 x (qmax-WL - qLd) x (LCL-d)]
VUT =
Shear at "d" from face of Pedestal in transverse direction [(LCT-d) x qTD + 0.5 x (qmax -WL - qTd) x (LTL-d)]
Critical Values
Load qmax (net) qTC qLC MUBL MUBT MUTL MUTT qLD qTD VUL VUT
WL
Case
201 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
202 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
203 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
204 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
205 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
206 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
207 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
208 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
209 20.10 #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A #N/A
Partial Safety Factor for Steel gs = 1.15 (Refer Cl. 36.4.2 of IS 456 -2000)
Top Reinforcement:
Longitudinal Direction
Where,
Mu
Ast reqd =
0.87 Fy . j .d
j =0 .5+ 0. 25−
gs =
√
j =
M
0 .87 fck . b . d . d
#N/A
Partial Safety Factor for Steel 1.15 (Refer Cl. 36.4.2 of IS 456 - 2000)
Design Strength of Steel fd = Yeild Strength / Partial Safety Factor
= 0.87 fy
Flexural reinforcement reuired Ast flex = #N/A mm2 ------------------ A
Percentage of Steel required r = #N/A %
Minimum area of reinforcement r min = 0.12 % of Gross cross sectional area
(Refer Cl. 26.5.2.1 of IS 456- 2000)
Ast min = 360 mm2 ------------------ B
Area of Steel required is maximum of A & B
Ast reqd = #N/A mm2 ###
Therefore, ks = 1.000
tc = 0.25 x Sqrt(fck)
= 1.370 N/mm2
Permissible Shear Stress (tcp) = 1 x 1.37
= 1.370 N/mm2
tvp ### tcp ###
###
###
Load Factor 1.05
Load Case Hx Py Hz Mx Mz
Max Fy 0.20 0.21 66.43 69.75 34.09 35.79 34.41 36.13 0.07 0.07
Min Fy 0.44 0.46 35.96 37.76 5.03 5.28 8.71 9.15 0.67 0.70
Max Hx 7.27 7.63 30.19 31.70 2.04 2.14 1.28 1.34 15.08 15.83
Max Hz 0.17 0.18 58.57 61.50 40.53 42.56 41.47 43.54 0.01 0.01
Max Mx 0.17 0.18 58.57 61.50 40.53 42.56 41.47 43.54 0.01 0.01
Max Mz 7.27 7.63 30.19 31.70 2.04 2.14 1.28 1.34 15.08 15.83
Mx + Mz 0.17 0.18 58.57 61.50 40.53 42.56 41.47 43.54 0.01 0.01
Modified
Horizontal Vertical Horizontal Moment
Node L/C Fx kN Fy kN Fz kN Mx kNm My kNm Mz kNm
101 101 102.32117 566.622 0 0 0 1681.54 1
102 18.321171 566.622 21 378 0 169.5405 2
103 65.678829 566.622 0 0 0 1342.46 3
104 18.321171 566.622 21 378 0 169.5405 4
105 84 566.622 18.321171 169.5405 0 1512 5
106 0 566.622 39.321171 547.5405 0 0 6
107 84 566.622 18.321171 169.5405 0 1512 7
108 0 566.622 2.6788287 208.4595 0 0 8
109 96.953068 566.622 12.953068 119.86513 0 1631.865 9
110 12.953068 566.622 33.953068 497.86513 0 119.8651 10
111 71.046932 566.622 12.953068 119.86513 0 1392.135 11
112 12.953068 566.622 8.0469319 258.13487 0 119.8651 12
113 18.321171 521.514 0 0 0 169.5405 13
114 18.321171 521.514 0 0 0 169.5405 14
115 0 521.514 18.321171 169.5405 0 0 15
116 0 521.514 18.321171 169.5405 0 0 16
117 12.953068 521.514 12.953068 119.86513 0 119.8651 17
118 12.953068 521.514 12.953068 119.86513 0 119.8651 18
119 84 566.622 0 0 0 1512 19
120 0 566.622 21 378 0 0 20
#VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 21
#VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 22
#VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 23
#VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 24
#VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 25
#VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 26
#VALUE! #VALUE! #VALUE! #VALUE! #VALUE! #VALUE! 27
Load Factor 1.05
Load Case Hx Py Hz Mx Mz
Max Fy 0.20 0.21 66.43 69.75 34.09 35.79 34.41 36.13 0.07 0.07
Min Fy 0.44 0.46 35.96 37.76 5.03 5.28 8.71 9.15 0.67 0.70
Max Hx 7.27 7.63 30.19 31.70 2.04 2.14 1.28 1.34 15.08 15.83
Max Hz 0.17 0.18 58.57 61.50 40.53 42.56 41.47 43.54 0.01 0.01
Max Mx 0.17 0.18 58.57 61.50 40.53 42.56 41.47 43.54 0.01 0.01
Max Mz 7.27 7.63 30.19 31.70 2.04 2.14 1.28 1.34 15.08 15.83
Mx + Mz 0.17 0.18 58.57 61.50 40.53 42.56 41.47 43.54 0.01 0.01