Sie sind auf Seite 1von 21

5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

POE EOC Unit 1
Due  May 21 at 11:59pm  Points  59  Questions  35  Available  May 11 at 12am ­ May 21 at 11:59pm  11 days  Time Limit  None
Allowed Attempts  3

Take the Quiz Again

A휇empt History
Attempt Time Score

LATEST Attempt 1  37 minutes 54 out of 59

 Correct answers are hidden.

Score for this attempt: 54 out of 59
Submitted May 18 at 10:54am
This attempt took 37 minutes.
 

Question 1 1 / 1 pts

There are 3 simple machines.

  True 

  False 

Question 2 1 / 1 pts

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 1/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

All simple machines manipulate magnitude of force and _________.

  distance 

  work 

  energy 

  time 

Question 3 1 / 1 pts

1. What is the actual mechanical advantage of the system?

  13.33 

  3.33 

  0.3 

  1.20 

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 2/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

Question 4 1 / 1 pts

A wheelbarrow is used to lift a 200­lb load. The length from the wheel axle to the center of the load is 2 ft. The length from the wheel and axle to
the effort is 5 ft.  Using static equilibrium calculations, calculate the effort force needed to overcome the resistance force in the system.

  80.0lb 

  2.5lb 

  500.0lb 

  40.0 

Question 5 1 / 1 pts

What is the linear distance traveled in one revolution of a 36­inch­diameter wheel?

  113in 

  36in 

  56.5in 

  9.42in 

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 3/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

Question 6 1 / 1 pts

An industrial water shutoff valve is designed to operate with 30 lb of effort force. The valve will encounter 200 lb of resistance force applied to a
1.5­ in.­diameter axle. 

1. What is the required actual mechanical advantage of the system?

  1.5 

  1 

  10 

  6.67 

Question 7 1 / 1 pts

A civil engineer must design a wheelchair accessible ramp next to a set of steps leading up to a building. The height from the ground to the top of
the stairs is 2 ft. Based on ADA codes, the slope must be 1:12 or less. Slope is equal to the rise of the ramp divided by the run of the ramp
.Using the ADA code, what is the allowable minimum length of the ramp base?

  24.1ft 

  12.0ft 

  24.0ft 

  0.042ft 

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 4/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

 
Partial Question 8 11 / 13 pts

Actual Mechanical Advantage  
The ra芠o of the magnitude of the resistance and effort forces applied to a system.

The ratio of the magnitude of the resistance and effort  
The ra芠o of the magnitude of the resistance and effort forces applied to a system.
forces applied to a system.

Efficiency  
The ra芠o of useful energy output to the total energy input, or the percentage of work input tha

Fulcrum  
The fixed point around which a lever rotates.

Ideal Mechanical Advantage  
Ra芠o of distance traveled by the applied effort and resistance force within a system.

Idler Gear  
A gear posi芠oned between the driver and the driven gear used to change rota芠onal direc芠on.

Inclined Plane  
A flat surface set at an angle (or incline) with no moving parts that is able to li objects by push

Lever  
A rigid bar used to exert a pressure or sustain a weight at one point of its length by the applica芠

Moment  
© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 5/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

The turning effect of a force about a point equal to the magnitude of the force 芠mes the perpendicular distance from the point to the line of ac芠on from the force.

Pitch  
Distance between adjacent threads in a screw.

Resistance Force  
An external force applied to an object.

Static Equilibrium  
A condi芠on where there are no net external forces ac芠ng upon a par芠cle or rigid body and the 

Torque  
A force that produces or tends to produce rota芠on or torsion.

Question 9 2 / 2 pts

Two lamps are wired in parallel. If another lamp is added in parallel. (Hint resistance and current are inversely proportionate)

  The total resistance will increase. 

  The voltage will drop 

  The total resistance will decrease 

  The total current stay the same. 

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 6/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

Question 10 1 / 1 pts

In a parallel circuit for lighting a home, which of the following is an advantage?

  Less wiring is used 

  Less chance of over heating 

  If one bulb goes out, none of them work 

  If one bulb goes out, the others still work 

Question 11 1 / 1 pts

In a series circuit for lighting a home, which of the following is an advantage?

  Less wiring is used 

  If one bulb goes out, the others still work 

  If one bulb goes out, none of them work 

  Higher chance of over heating 

Question 12 1 / 1 pts
© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 7/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

________________are diagrams consisting of symbol representations and configurations of electrical components within a circuit. 

  Map 

  Schematics 

  Blue Print 

  Bread Board 

Question 13 1 / 1 pts

On a camping trip, you decide to use a cordless air pump to inflate an inflatable mattress. If the air pump is powered by a 12­volt battery with a
resistance of 18 ohms, what is the amount of current flowing through the circuit?

  1.5 A 

  0.67 A 

  1.5 V 

  0.67 V 

Question 14 1 / 1 pts

The current of electricity is like the __________.

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 8/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

  IDK 

  flow of water 

  rock in the pipe 

  size of the tank 

Question 15 1 / 1 pts

Match the term to its letter

Resistance  
R

Current  
I

Voltage  
V

Question 16 1 / 1 pts

How many valence electrons do good electrical conductors have?

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 9/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

  3­6 

  1­3 

  6­8 

  8 or more 

Question 17 1 / 1 pts

Match the subatomic particle with the correct charge.

Electron  
Nega芠ve

Proton  
Posi芠ve

Neutron  
Neutral

Question 18 1 / 1 pts

________________ assumes that current flows out of the positive side of the battery, through the circuit, and back to the negative side of the
battery. This was the convention established when electricity was first discovered, but it is incorrect!
© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 10/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

  Electron flow 

  Mr. Johnston 

  Conventional current 

  Ohms Law 

 
Partial Question 19 3 / 4 pts

Matching

The sum of all voltage drops in a series circuit equals  
Kirchhoff’s Voltage Law (KVL): Series
the total applied voltage

The total current in a parallel circuit equals the sum of  
Kirchhoff’s Current Law (KCL): Parallel
the individual branch currents

The total current in a parallel circuit equals the sum of  
Kirchhoff’s Current Law (KCL): Parallel
the individual branch currents

The total resistance (RT) is equal to the reciprocal of  
Kirchhoff's resistance Law : Parallel
the sum of the reciprocal:

 
Incorrect Question 20 0 / 1 pts
© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 11/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

The images in Figures 7 and 8 show the voltmeter configurations that two different POE students used to take a voltage reading within a simple
circuit. Only one of the two students was able to measure the voltage value in the simple circuit. Use the information given in the figures to
answer the following questions.

1. Which of the two setups (Figure 7 or Figure 8) shows the correct way to measure voltage?

2. If the amount of current in the circuit is equal to 0.625A, what is the voltage value of the power supply?

  Figure 7, 10 Volts 

  Figure 8, 10 Volts 

  Figure 7, 25.6 Volts 

  Figure 8, 25.6 Volts 

Question 21 1 / 1 pts

In a series circuit, increasing the resistance while keeping voltage the same will cause the current to:
© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 12/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

  increase 

  stay the same 

  decrease 

  go to zero 

Question 22 1 / 1 pts

Which of the circuits below would have the same current (I)?

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 13/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

  All of them have the same current 

  None of them have the same current 

  A & B only 

  B & D only 

  A, C & E only 

  B & C only 

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 14/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

Question 23 1 / 1 pts

An electric motor uses 800J of electric energy to lift a cargo box doing 600J of work to it. What is the efficiency of this system?

  90% 

  133% 

  75% 

  25% 

Question 24 1 / 1 pts

ATV winches pull a horizontal load during testing. The winch pulls a weight where the friction produces a force which is measured as tension in
the cable. The following data can be used to compare electrical input to mechanical output to determine system efficiency.

Scenario Force Distance Time Current Volts


1 0 N 24 m 180 s 15 A 12 V
2 7000 N 24 m 360 s 100 A 12 V
3 11000 N 24 m 720 s 160 A 12 V

Which scenario is most efficient?

  Scenario 2 and 3 are equally efficient 

  Scenario 2 

  Scenario 3 

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 15/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

  Scenario 1 

 
Incorrect Question 25 0 / 1 pts

An elevator motor lifts 500 kg of mass to the height of the fourth floor of an office building (11.0 meters above ground level) at a constant speed in
6 seconds. Determine the power rating of the motor.

  856 W 

  523 W 

  273 W 

  917 W 

Question 26 1 / 1 pts

When using a multimeter, for which test should the circuit be disconnected from its power source?

  Resistance 

  Continuity 

  Voltage 

  Amperage 
© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 16/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

Question 27 1 / 1 pts

Power can be expressed in the amount of energy expended or work performed during a given time period.  In other terms power is simply the
rate at which energy is converted.  So in order to determine how much power electrical energy can supply to be converted into mechanical you
can use all of the following quantities except:

  Time 

  Distance 

  Force 

  Height 

Question 28 1 / 1 pts

A circuit with parallel resistors (R1 and R2) has a total resistance of 8 ohms. What is a possible value for the resistance of R1?

  16 ohms 

  4 ohms 

  2 ohms 

  8 ohms 

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 17/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

Question 29 1 / 1 pts

Andy is using an incline plane to pull a 260 lb load up to a height of 5 ft. The ramp is 13 ft long and the effort used to pull the load is 155 lbs.
Determine the efficiency of this simple machine.

  2.60 

  0.65 

  1.68 

  0.55 

Question 30 1 / 1 pts

A 100 N force is being applied to an object weighing 15 N a distance of 5 m. The object moves at constant speed so how much work has been
done?

  100 J 

  375 J 

  250 J 

  500 J 

 
© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 18/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

Question 31 1 / 1 pts

A 15 kg bike is pushed up a ramp of length 275 m.  The ramp incline is 25 degrees. The bike is pushed with a 25 N force parallel to the ramp and
it takes 18.0 sec to do the job.   What is the work and power, respectively?

  6900 J; 383 W 

  11 J; 0.0026 W 

  6900 J; 0.0026 W 

  11 J; 383 W 

Question 32 3 / 3 pts

 A hydrogen fuel cell by itself is not sufficient to power much of anything in our society.  How could fuel cells be configured to produce enough
voltage and current to a system? Select all that apply.

  Improve the storage of hydrogen 

  You could combine it with another source of energy. 

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 19/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

  You could increase the cost of the fuel. 

  You could put them in series not in parallel. 

Question 33 4 / 4 pts

Select all of the benefits of hydrogen fuel cells.

  cheap 

  safe 

  quiet 

  sustainable 

  clean 

Question 34 1 / 1 pts

Select all of the ways that one might collect 'lost" energy in ones school or home.

  Using a device that filters lint but lets the hot air created by the dryer return into the home. (in winter) 

  In winter, leaving hot water in tub to cool before letting it go down the drain. 

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 20/21
5/18/2017 POE EOC Unit 1: Principles of Engineering 2016 JJohnston Russellville High School 01

  Turning off the lights when not in use. 

  Keeping the thermostat set on 65. 

Question 35 4 / 4 pts

Alternative Energy  
energy generated in ways that do not deplete natural resources or harm the environment, espe

Electrolysis  
The process separa芠ng the hydrogen‐oxygen bond in water using an electrical current.

Renewable Energy  
A resource that can be replaced when needed.

Energy  
The ability to do work.

Quiz Score: 54 out of 59

© 2016 Project Lead The Way, Inc.
https://pltw.instructure.com/courses/500519/quizzes/401340/take 21/21

Das könnte Ihnen auch gefallen