Beruflich Dokumente
Kultur Dokumente
Introduction
Purpose is to provide:
A prompt for preparing data for new installations.
A datapack for installers.
A data entry form to capture additional as-built data.
An as-built record with sign-off.
Navigation:
The Master Site Data column lists entries required. Click on a
‘+’ tab at the far left of the screen to open up required links and
modules for the Node. Click ‘–’ tab to close.
The Build / As-Built Data column is for data entry. Build data
is data to be entered at the planning (datapack prep) stage. As-
built data is data to be entered at site, mostly from Portal.
The Portal column highlights the data to be entered
and data to be entered from Portal.
The Comments column is to capture any additional data.
General Instructions:
IRU 600 #1
IRU 600 #2
Networking
Terminal IP Address To
Subnet Mask To
Static or dynamic routing To
Static routing data
DHCP yes/no; address range To
Trap destinations To
Link
Link
Link
Link
DAC 16x
DAC 16x
DAC 4x
DAC 2x155e
DAC ES
DAC GE
DAC GE
DAC 155oM
DAC 3xE3/DS3
DAC 3xE3/DS3M
Traffic Circuits
AUX
NPC
PCC
Date/Time
(Specify Date/Time setting) To
Ground checks
Single point bldg ground y/n
Master Ground Bar resistance
Rack to MGB resistance
PSU to MGB resistance
Tower ground resistance(s)
Other resistance readings
Meter used
Name:
Signature:
Date:
Completion Comments
General Instructions: 4-wheel drive access only. This time of the year the track will be wet and slippery. Please do a battery check and run the back-up diesel generator
for about 30 mins and check associated panel lights. Should all be green.
Networking
Terminal IP Address 192.168.10.1 To
Subnet Mask 225.225.255.0. To
Static or dynamic routing RIP 2 To
Static routing data N/A
DHCP yes/no; address range Yes, 192.168.10.2 to 192.168.10.10 To
Trap destinations N/A To
Link 1
Link name/number Lakeside-Belmont To
Remote end site name Belmont To
Remote end node/terminal name E103 To
Local antenna type(s) VHLP2-180-EX
Local antenna diameter(s) 0.6M
Antenna serial number(s) AN35235
Height on tower / pole mount ID 21M `
Initial pointing (compass/map ref) 74 degrees
Polarization Vertical
Protected yes/no No To
Protection type N/A To
ODU(s) direct mounting, yes/no Yes
ODU type ODU 300hp
ODU serial number SNA7687988 From
ODU cable length(s) required 35m
Location of RAC in INU Slot 1 To
RAC type RAC 30
RAC serial number LEA00878770 From
Tx frequency 17.85 GHz To
Rx frequency 18.25 GHz To
T/R spacing 400 MHz To
Tx power 17 dBm To
Detected forward power 17.1 dBm From
Capacity 32xE1 To
Modulation 16QAM To
Link 2
Link name/number Lakeside to Pine Hill To
Remote end site name Pine Hill To
Remote end node/terminal name E102 To
Local antenna type(s) VHLP2-180-EX
Local antenna diameter(s) 0.6M
Antenna serial number(s) SN12495
Height on tower / pole mount ID 21M
Initial pointing (compass/map ref) 178 degrees
Polarization Vertical
Protected yes/no No To
Protection type N/A To
ODU(s) direct mounting, yes/no Yes
ODU type ODU 300hp
ODU serial number SNBO93859 From
ODU cable length(s) required 38m
Location of RAC in INU Slot 2 To
RAC type RAC 30
RAC serial number LEN00243551 From
Tx frequency 17.95 GHz To
Rx frequency 18.35 GHz To
T/R spacing 400 MHz To
Tx power 22dBm To
Detected forward power 21.5 dBm From
Capacity 32xE1 To
Modulation 16QAM To
ATPC yes/no No To
ATPC data
Expected RSL -53 dBm
Measured RSL -52 dBm From
Expected RSSI 1.3v
Indicated RSSI 1.35v From
Expected fade margin 33 dB
Measured fade margin 32 dB From
G.826 link check Zero errors over 14 hours From
Alarms check No active alarms from Link 2 From
Performance check All indications normal From
Link 2
Link 3
Link 4
DAC 16x
DAC location in INU Slot 4 To
Serial number LEX00234567 From
E1 or DS-1 E1 To
Bal or Unbal Unbal To
DS1 encoding N/A To
DS1 line length N/A To
Port / trib names Lak 1 to 8 To
Connect to Rack BNC panel: ports 1 to 8
DAC 16x
DAC 16x
DAC 4x
DAC 2x155e
DAC 3xE3/DS3
DAC 3xE3/DS3M
Traffic Circuits
Bus configuration E1 To
Circuit connections Link 1 ports 1-8 to DAC 16x, slot 4, ports 1-8. To
Link 1 ports 9 to 32 to Link 2, slot 2, ports 1 to
24.
AUX
AUX location in INU Slot 3 To
Serial number LEA05090295 From
Auxiliary ports
Port 1: function, type, port settings, Data, sync, P1, default, Aux Bel/Lak To
name
Port 2: function, type, port settings, To
name
Port 3: function, type, port settings, To
name
Auxiliary ports
Auxiliary circuits
Port 1: to/circuit name Port 1 to Link 1 port 1, Bel/Lak To
Port 1: to/circuit name To
Port 1: to/circuit name To
Auxiliary circuits To
Alarm I/O
Port layout 4xin, 2xout To
Port 1, type, active condition Digital input, active high To Wire to intruder alarm: alarm is active when circuit is
broken.
Port 2, type, active condition To
Port 3, type, active condition To
Port 4, type, active condition To
Port 5, type, active condition To
Port 6, type, active condition To
Alarm I/O
Alarm actions
Destination IP address, slot, and 192.168.2.1, slot 4, output 1. To At commissioning check that the destination output (bell)
output. Trigger(s). AUX alarm input 1. at Belmont activates when the intruder alarm is activated.
Also check that the alarm event is raised at the NOC.
NPC
Date/Time
(Specify Date/Time setting) Sync to Portal PC Date/Time To
Completion Comments The second farm gate is almost off its hinges.
One of the two tower-top warning lights is out.
Diesel generator checked out OK
Checked by:
Name:
Signature:
Date:
Additional Comments:
Site Name:
Signed By:
Customer
Name:
Signature:
Title:
Date:
Stratex Networks
Name:
Signature:
Title:
Date:
Site Name:
Signed As Completed
Customer
Name:
Signature:
Title:
Date:
Stratex Networks
Name:
Signature:
Title:
Date: