Beruflich Dokumente
Kultur Dokumente
PLATE
ASTM A514 Grade S
High-Yield-Strength, Quenched and Tempered AlloySteel Plate
ASTM A514 Grade S is a quenched and tempered alloy steel plate for structural
applications
requiring high yield strength combined with good formability and toughness. A514 Grade S
has
a minimum yield strength of 690 MPa [100 ksi] and may be ordered with supplemental
Charpy
equipment, crane booms, mobile man-lifts, agricultural equipment, heavy vehicle frames
and
Dimensions Available:
Standard plate thicknesses available (96” wide x 240” pattern size) include
4.8, 6.4, 9.5, 12.7, 19.0, 25.4 and 31.8 mm (3/16”, ¼”, 3/8”, ½”, ¾”, 1” and 1-1/4”).
0.2% YS
Elongation in 50 Reduction of Brinell
MPa [ksi], UTS MPa [ksi]
mm [2”], min. % Area, min. % Hardness*
min.
* For plates up to 0.375”, a Brinell hardness test may be used instead of a tensile test for
those plates not
requirement. A minimum Charpy V-notch impact energy value of 20 ft-lbs [27 J] at -50°F
[-45°C]
Chemical Composition
Meets chemical requirements of ASTM A514 Grade S, as shown below (wt % ladle
analysis):
4.8 – 19
Min. 0.11 1.10 − − 0.15 0.10 − 0.001 0.48 0.45
[0.1875” –
0.625”]
>19 – 31.8
Max. 0.21 1.50 0.035 0.008* 0.45 0.60 0.06 0.005 [>0.625” – 0.54 0.46
1.25”]
* Note that our S level is more restrictive than ASTM specification requirements for A514
Grade S
Tolerances
Thickness, width, and length tolerances for A514 Grade S steel plate are in accordance with
the
requirements of ASTM A6. The flatness tolerance for as supplied product is ½ ASTM A6.
Delivery Condition
welding code. In the absence of a specified welding code, the following suggested
minimum
preheat and interpass temperatures and welding consumables are provided. Special welding
consumables and welding procedures may be required to match the base metal toughness.
Low hydrogen practices are strongly recommended, including the removal of surface
moisture.
A514 Grade S may be susceptible to reheat cracking in the heat-affected zone of welds
during
stress relieving or postweld heat treatment. As a result, Beverly Steel recommends that a
qualified welding engineer consider this potential before stress relieving weldments of this
product.
Minimum Preheat
Welding and
Thickness, mm [in] Consumables
Process Interpass
Temperature
Formability: A514 Gr S material exhibits good cold forming characteristics. Shear burrs
and heat-affected zones of thermal cut edges on or near the bend axis as well as sharp
corners
on edges and on gas cut or punched holes located on or adjacent to the bend axis should be
removed by grinding prior cold forming. The following recommended minimum inside
bend
radius, R, and die width opening, W, as a function of bending orientation are provided:
Bend axis perpendicular Bend axis parallel
4.8 – 19
1.75t 7t 2.625t 9t
[0.1875” – 0.75”]
>19 – 25.4
2.25t 8t 3.375t 10t
[>0.75” – 1.00”]
>25.4 – 31.8
4.5t 12t 6.75t 16t
[>1.00” – 1.25”]
ASTM A514 Grade F|A514 Gr.F STE
Gangsteel is specialized in supplying ASTM A514 steel plate in A514 Grade F,A514 Gr.F ,A514 Gr F STEEL
PLATE
ASTM A514 Grade Q|A514 Gr.Q STE
Gangsteel is specialized in supplying ASTM A514 steel plate in A514 Grade Q,A514 Gr.Q,514 Gr Q STEEL
PLATE