Beruflich Dokumente
Kultur Dokumente
2017 Edition
Unmatched Product Range Material Availability Manufacturing Capabilities Innovative Applications and Engineering Expertise
Your True Project Partner
Material Availability
With strategic stocking locations throughout the Americas,
Skyline Steel has established a material delivery network that is primed
for immediate response. Our facilities offer barge, rail and truck
transportation options for cost effectiveness and on-time delivery.
Manufacturing Capabilities
Skyline Steel owns and operates pipe, sheet pile, geostructural
and pile accessory facilities. Production is supplemented with
full fabrication capabilities to provide a single source for all your
foundation needs.
1 ft = 0.3048 m 1m = 3.2808 ft
Recycled Content
Hot Rolled: 100%
Cold Form: 80%
Recyclable: 100%
Skyline Steel supplies a wide variety of sheet pile from leading manufacturers.
Hot rolled and cold formed are two primary methods of manufacturing sheet pile. While there are key differences between
these two methods, the most important distinction is the interlock. Since hot rolled sheet piles are produced from steel at
high temperatures, the interlock tends to be tighter than its cold formed counterpart. Normally, looser interlocks are not
recommended in extremely hard driving conditions or for walls requiring low permeability.
Around the world, sheet piles are utilized for various applications. Z-pile, named after its shape, is commonly used for
cofferdams, levee strengthening, retaining structures, breakwaters, and bulkheads. In addition to these traditional
applications, steel sheet piles are also used for bridge abutments, environmental barrier walls, underground parking
garages, and depressed roads and railways. Sheet piles can also serve as permanent structural members in all of the
applications listed above.
Sheet pile designs are based on the bending properties, section modulus, and moment of inertia. Durability and drivability
of each section is also taken into consideration.
Flat sheet piles (straight web sheets) are used in the construction of cellular structures. Cellular cofferdams are utilized
to dewater large areas during the construction of locks and dams and are also employed as permanent walls when loads
are exceptionally high or there is little or no soil for embedment. Since the cells are gravity structures, large embedment
is generally not necessary. The tension is resisted by the interlock. Unlike Z-pile or combination walls, interlock strength is
the main design consideration for cellular cofferdams. The weight of the cell and the resistance of the flat sheet interlocks
provide the stability of the structure.
Calgary, AB
Columbus, OH Nome, AK
NZ/PZ
NZ/PZ Hot Rolled Steel Sheet Pile
tf
tw
h
W W
NZ
NZ 14 30.31 13.39 0.375 0.375 6.40 55 21.77 25.65 30.50 171.7 6.10 1.20
770 340 9.5 9.5 135.4 81.26 106.30 1379 1640 23447 1.86 1.20
NZ 19 27.56 16.14 0.375 0.375 7.07 55 24.05 35.08 41.33 283.1 6.18 1.35
700 410 9.5 9.5 149.6 81.85 117.40 1886 2222 38659 1.88 1.35
NZ 20 27.56 16.16 0.394 0.394 7.34 57 24.82 36.24 42.80 292.8 6.18 1.35
700 411 10.0 10.0 155.4 85.37 122.00 1948 2301 39984 1.88 1.35
NZ 21 27.56 16.20 0.433 0.433 7.80 61 26.56 38.69 45.85 313.4 6.18 1.35
700 412 11.0 11.0 165.2 90.78 129.70 2080 2465 42797 1.88 1.35
NZ 26 27.56 17.32 0.500 0.500 9.08 71 30.99 48.50 57.01 419.9 6.49 1.41
700 440 12.7 12.7 192.2 105.66 151.30 2608 3065 57340 1.98 1.41
NZ 28 27.56 17.38 0.560 0.560 9.98 78 33.96 52.62 62.16 457.4 6.49 1.41
700 441 14.2 14.2 211.2 116.08 165.82 2829 3342 62461 1.98 1.41
PZ 22 22.0 9.0 0.375 0.375 6.47 40.3 22.0 18.1 21.79 84.38 4.48 1.22
559 229 9.50 9.50 136.9 60.0 107.4 973 1171.4 11500 1.37 1.22
PZ 27 18.0 12.0 0.375 0.375 7.94 40.5 27.0 30.2 36.49 184.20 4.48 1.49
457 305 9.50 9.50 168.1 60.3 131.8 1620 1961.9 25200 1.37 1.49
PZ 35 22.6 14.9 0.600 0.500 10.29 66.0 35.0 48.5 57.17 361.22 5.37 1.42
575 378 15.21 12.67 217.8 98.2 170.9 2608 3073.5 49300 1.64 1.42
PZ 40 19.7 16.1 0.600 0.500 11.77 65.6 40.0 60.7 71.92 490.85 5.37 1.64
500 409 15.21 12.67 249.1 97.6 195.3 3263 3866.7 67000 1.64 1.64
NZ/PZ
ASTM YIELD STRENGTH
(ksi) (MPa)
A 328 39 270
A 572 Grade 50 50 345
A 572 Grade 60 60 415
A 588 50 345
A 690 50 345
A A A
A A
A
A
135º
B B B B 90º
B B 90º
α B B α α B B
B DD
A C
A C
AZ 13-770 30.31 13.54 0.354 0.354 5.94 51.14 20.24 24.2 28.8 163.7 6.07 1.20
770 344 9.0 9.0 125.8 76.1 98.8 1300 1546 22360 1.85 1.20
◆ AZ 14-770 30.31 13.56 0.375 0.375 6.21 53.42 21.14 25.2 30.0 170.6 6.07 1.20
770 345 9.5 9.5 131.5 79.5 103.2 1355 1611 23300 1.85 1.20
AZ 17-700 27.56 16.52 0.335 0.335 6.28 49.12 21.38 32.2 37.7 265.3 6.10 1.33
700 420 8.5 8.5 133.0 73.1 104.4 1730 2027 36230 1.86 1.33
AZ 18-700 27.56 16.54 0.354 0.354 6.58 51.41 22.39 33.5 39.4 276.8 6.10 1.33
700 420 9.0 9.0 139.2 76.5 109.3 1800 2116 37800 1.86 1.33
◆ AZ 19-700 27.56 16.56 0.375 0.375 6.88 53.76 23.35 34.8 41.0 288.4 6.10 1.33
700 421 9.5 9.5 145.6 80.0 114.3 1870 2206 39380 1.86 1.33
AZ 20-700 27.56 16.57 0.394 0.394 7.18 56.11 24.43 36.2 42.7 300.0 6.10 1.33
700 421 10.0 10.0 152.0 83.5 119.3 1945 2296 40960 1.86 1.33
AZ 18-800 31.5 17.68 0.335 0.335 6.07 54.26 20.67 34.2 39.7 302.6 6.82 1.30
800 449 8.5 8.5 128.6 80.7 100.9 1840 2135 41320 2.08 1.30
AZ 20-800 31.5 17.72 0.375 0.375 6.66 59.50 22.67 37.2 43.3 329.9 6.82 1.30
800 450 9.5 9.5 141.0 88.6 110.7 2000 2330 45050 2.08 1.30
AZ 22-800 31.5 17.76 0.413 0.413 7.25 64.77 24.68 40.3 47.0 357.3 6.82 1.30
800 451 10.5 10.5 153.5 96.4 120.5 2165 2525 48790 2.08 1.30
AZ 23-800 31.50 18.66 0.453 0.354 7.12 63.56 24.22 43.3 49.9 404.6 6.94 1.32
800 474 11.5 9.0 150.6 94.6 118.2 2330 2680 55260 2.11 1.32
AZ 25-800 31.50 18.70 0.492 0.394 7.71 68.91 26.26 46.5 53.8 435.1 6.94 1.32
800 475 12.5 10.0 163.3 102.6 128.2 2500 2890 59410 2.11 1.32
AZ 27-800 31.50 18.74 0.531 0.433 8.31 74.26 28.29 49.7 57.6 465.5 6.94 1.32
800 476 13.5 11.0 176.0 110.5 138.1 2670 3100 63570 2.11 1.32
AZ 24-700 27.56 18.07 0.441 0.441 8.23 64.30 28.00 45.2 53.5 408.8 6.33 1.38
700 459 11.2 11.2 174.1 95.7 136.7 2430 2867 55820 1.93 1.38
◆ AZ 26-700 27.56 18.11 0.480 0.480 8.84 69.12 30.10 48.4 57.1 437.3 6.33 1.38
700 460 12.2 12.2 187.2 102.9 146.9 2600 3070 59720 1.93 1.38
AZ 28-700 27.56 18.15 0.520 0.520 9.46 73.93 32.19 51.3 60.9 465.9 6.33 1.38
700 461 13.2 13.2 200.2 110.0 157.2 2760 3273 63620 1.93 1.38
29.53 20.04 0.472 0.394 8.09 67.73 27.53 52.3 60.3 523.9 6.93 1.41
AZ 28-750 750.0 509.0 12.00 10.00 171.2 100.80 134.40 2810 3245 71540 2.11 1.41
29.53 20.08 0.512 0.433 8.73 73.08 29.70 55.9 64.8 561.5 6.93 1.41
AZ 30-750 750.0 510.0 13.00 11.00 184.7 108.80 145.00 3005 3485 76670 2.11 1.41
29.53 20.12 0.551 0.472 9.37 78.44 31.88 59.5 69.2 599.0 6.93 1.41
AZ 32-750 750.0 511.0 14.00 12.00 198.3 116.70 155.60 3200 3720 81800 2.11 1.41
AZ 36-700N 27.56 19.65 0.591 0.441 10.20 79.72 34.71 66.8 76.4 656.2 6.73 1.47
700 499 15.0 11.2 215.9 118.6 169.5 3590 4110 89610 2.05 1.47
◆ AZ 38-700N 27.56 19.69 0.630 0.480 10.87 84.94 36.98 70.6 81.1 694.5 6.73 1.47
700 500 16.0 12.2 230.0 126.4 180.6 3795 4360 94840 2.05 1.47
AZ 40-700N 27.56 19.72 0.669 0.520 11.54 90.16 39.26 74.3 85.7 732.9 6.73 1.47
700 501 17.0 13.2 244.2 134.2 191.7 3995 4605 100080 2.05 1.47
AZ 42-700N 27.56 19.65 0.709 0.551 12.22 95.51 41.59 78.2 90.3 768.4 6.75 1.47
700 499 18.0 14.0 258.7 142.1 203.1 4205 4855 104930 2.06 1.47
AZ 44-700N 27.56 19.69 0.748 0.591 12.89 100.74 43.87 81.9 95.0 806.6 6.75 1.47
700 500 19.0 15.0 272.8 149.9 214.2 4405 5105 110150 2.06 1.47
AZ 46-700N 27.56 19.72 0.787 0.630 13.56 105.97 46.14 85.7 99.5 844.9 6.75 1.47
700 501 20.0 16.0 287.0 157.7 225.3 4605 5350 115370 2.06 1.47
AZ 46 22.83 18.94 0.709 0.551 13.76 89.10 46.82 85.5 98.5 808.8 6.20 1.63
580 481 18.0 14.0 291.2 132.6 228.6 4595 5295 110450 1.89 1.63
AZ 48 22.83 18.98 0.748 0.591 14.48 93.81 49.28 89.3 103.3 847.0 6.20 1.63
580 482 19.0 15.0 306.5 139.6 240.6 4800 5553 115670 1.89 1.63
AZ 50 22.83 19.02 0.787 0.630 15.22 98.58 51.80 93.3 108.2 886.5 6.20 1.63
580 483 20.0 16.0 322.2 146.7 252.9 5015 5816 121060 1.89 1.63
27.56 19.80 0.866 0.591 13.63 106.49 46.37 88.4 102.1 876.2 6.70 1.46
AZ 48-700 700.0 503.0 22.00 15.00 288.4 158.50 226.40 4755 5490 119650 2.04 1.46
27.56 19.84 0.906 0.630 14.30 111.73 48.65 92.2 106.7 914.6 6.70 1.46
AZ 50-700 700.0 504.0 23.00 16.00 302.6 166.30 237.50 4955 5735 124890 2.04 1.46
27.56 19.88 0.945 0.669 14.97 116.97 50.93 95.9 111.3 953.0 6.70 1.46
AZ 52-700 700.0 505.0 24.00 17.00 317.0 174.10 248.70 5155 5985 130140 2.04 1.46
◆ In stock.
Corner Piles
~0.98" ~2.76" ~1.18"
~(25 mm) ~(70 mm) ~0.59"
~(30 mm) ~(15 mm)
C 14 Omega 18 E 22 Delta 13
Grade: S 355 GP Grade: S 430 GP Grade: S 355 GP Grade: S 355 GP
Weight: 9.68 lb/ft Weight: 12.10 lb/ft Weight: 6.87 lb/ft Weight: 8.73 lb/ft
(14.4 kg/m) (18.0 kg/m) (10.2 kg/m) (13.0 kg/m)
> 8.5 mm ± 6%
Single Pile Width ± 2%
Double Pile Width ± 3%
Straightness 0.2% of the length Single Pile Double Pile
Ends out of Square 2% of the width Position B Form II on Request
SCZ 14 28.50 10.00 0.250 4.18 33.81 14.23 14.36 16.32 71.82 6.10 1.28
723.9 254.0 6.4 88.48 50.31 69.50 772 877.4 9808 1.86 1.28
SCZ 16 28.50 10.00 0.276 4.62 37.37 15.73 15.75 17.97 78.73 6.10 1.28
723.9 254.0 7.0 97.79 55.61 76.82 847 965.9 10751 1.86 1.28
SCZ 17N 28.50 10.00 0.295 4.95 40.03 16.86 16.87 19.21 84.35 6.10 1.28
723.9 254.0 7.5 104.78 59.58 82.32 907 1033 11519 1.86 1.28
SCZ 18N 28.50 10.00 0.317 5.31 42.94 18.08 18.10 20.61 90.48 6.10 1.28
723.9 254.0 8.1 112.39 63.91 88.28 973 1108 12356 1.86 1.28
SCZ 21N 28.50 10.00 0.375 6.29 50.84 21.41 21.43 24.40 107.13 6.10 1.28
723.9 254.0 9.5 133.06 75.66 104.54 1152 1312 14629 1.86 1.28
SKZ 20 28.50 16.00 0.315 6.00 48.24 20.31 31.69 36.66 253.51 7.60 1.60
723.9 406.4 8.0 127.00 71.79 99.17 1704 1970.97 34618 2.32 1.60
SKZ 22 28.50 16.00 0.335 6.30 51.30 21.60 33.43 38.94 267.40 7.60 1.60
723.9 406.4 8.5 133.35 76.34 105.46 1797 2093.55 36515 2.32 1.60
SKZ 23 28.50 16.00 0.354 6.70 54.20 22.82 35.61 41.12 284.90 7.60 1.60
723.9 406.4 9.0 141.82 80.66 111.42 1915 2210.75 38905 2.32 1.60
SKZ 24 28.50 16.00 0.375 7.10 57.43 24.18 37.73 43.52 301.80 7.60 1.60
723.9 406.4 9.5 150.28 85.47 118.06 2028 2339.78 41213 2.32 1.60
SKZ 25 28.50 16.00 0.399 7.60 61.10 25.73 40.14 46.24 321.12 7.60 1.60
723.9 406.4 10.1 160.87 90.93 125.61 2158 2486.02 43851 2.32 1.60
SKZ 31 28.50 18.00 0.450 9.07 73.82 31.08 51.56 60.51 464.05 8.06 1.70
723.9 457.2 11.4 192.04 109.85 151.75 2772 3253.29 63369 2.46 1.70
SKZ 33 28.50 18.00 0.475 9.40 77.64 32.69 54.89 63.57 494.03 8.06 1.70
723.9 457.2 12.1 198.97 115.54 159.61 2951 3417.68 67462 2.46 1.70
SKZ 34 28.50 18.00 0.500 9.89 81.42 34.28 57.62 66.86 518.62 8.06 1.70
723.9 457.2 12.7 209.25 121.17 167.38 3098 3594.60 70821 2.46 1.70
SKZ 36 28.50 18.00 0.535 10.78 86.81 36.55 60.71 71.58 546.43 8.06 1.70
723.9 457.2 13.6 228.10 129.19 178.46 3264 3848.17 74619 2.46 1.70
SKZ 38 28.50 18.00 0.550 11.07 88.95 37.45 62.32 73.52 560.85 8.06 1.70
723.9 457.2 14.0 234.42 132.37 182.85 3350 3952.44 76588 2.46 1.70
Interlock Compatibility
SCZ 17N
SCZ 18N
SCZ 21N
SKZ 20
SKZ 22
SKZ 23
SKZ 24
SKZ 25
SKZ 31
SKZ 33
SKZ 34
SKZ 36
SKZ 38
SCZ 14
SCZ 16
SCZ 14 l l l l l l l l l l
SCZ 16 l l l l l l l l l l
SCZ 17N l l l l l l l l l l
SCZ 18N l l l l l l l l l l
SCZ 21N l l l l l l l l l l
SKZ 20 l l l l l l l l l l
SKZ 22 l l l l l l l l l l
SKZ 23 l l l l l l l l l l
SKZ 24 l l l l l l l l l l
SKZ 25 l l l l l l l l l l
SKZ 31 l l l l l
SKZ 33 l l l l l
SKZ 34 l l l l l
SKZ 36 l l l l l
SKZ 38 l l l l l
Corner Piles
B2 Corner Pile B3 Corner Pile
5.0” 5.0”
(127 mm) (127 mm)
23.5”
23.5” (596.9 mm)
(596.9 mm)
Mass ± 2.5% ± 7%
Length + 5 inches – 0 inches ± 50 mm
Straightness
Bending (S) 0.25% of the length
SKL 9 21.65 3.54 0.157 2.53 15.52 8.60 2.55 3.28 4.50 4.23 1.17
550 90 4.0 53.50 23.10 42.00 137 176.43 615 1.29 1.17
SKL 10 21.65 3.54 0.177 2.83 17.40 9.63 2.88 3.67 5.09 4.23 1.17
550 90 4.5 59.90 25.90 47.00 155 197.23 695 1.29 1.17
SKL 12 21.65 3.54 0.217 3.43 21.10 11.67 3.53 4.42 6.22 4.23 1.17
550 90 5.5 72.60 31.40 57.00 190 237.66 850 1.29 1.17
SKS 11 27.56 5.91 0.197 3.29 25.69 11.26 6.34 7.54 18.67 5.87 1.28
700 150 5.0 69.60 38.23 55.00 341 405.36 2550 1.79 1.28
SKS 13 27.56 5.91 0.217 3.61 28.22 12.29 6.98 8.44 20.48 5.87 1.28
700 150 5.5 76.40 42.00 60.00 375 454.03 2810 1.79 1.28
SKS 14 27.56 5.91 0.250 4.17 32.58 14.19 8.05 9.48 23.78 5.87 1.28
700 150 6.4 88.20 48.49 69.27 433 509.87 3247 1.79 1.28
SKS 16 27.56 5.91 0.276 4.57 35.61 15.57 8.89 10.40 26.25 5.87 1.28
700 150 7.0 96.70 53.00 76.00 478 559.20 3585 1.79 1.28
Interlock Compatibility
SKL 9 SKL 10 SKL 12 SKS 11 SKS 13 SKS 14 SKS 16
SKL 9 l l l l l l l
SKL 10 l l l l l l l
SKL 12 l l l l l l l
SKS 11 l l l l l l l
SKS 13 l l l l l l l
SKS 14 l l l l l l l
SKS 16 l l l l l l l
Corner Piles
D1 Corner Piles D3 Corner Piles
Mass ± 2.5% ± 7%
Length + 5 inches – 0 inches ± 50 mm
Straightness
Bending (S) 0.25% of the length
PS 27.5 19.69 0.4 20 30 8.09 45.1 27.5 3.3 5.3 3.65 1.11
500 10.2 3500 9.14 171.2 67.1 134.3 54 221 1.11 1.11
† Minimum cell diameter cannot be guaranteed for piles over 65 feet (19.81 m) in length, or if piles are spliced. 58 piles are needed to make a 30 foot diameter cell.
AS 500 19.69 0.375 17.1 7.71 43.01 26.22 2.3 4.1 3.77 1.15
4.5
9.5 500 9.5 3000 163.2 64.0 128 37 170 1.15 1.15
AS 500 19.69 0.433 20.0 8.50 47.46 28.88 3.0 4.5 3.77 1.15
4.5
11.0 500 11.0 3500 180.0 70.6 141 49 186 1.15 1.15
AS 500 19.69 0.472 28.5 8.94 49.93 30.52 3.1 4.7 3.77 1.15
4.5
12.0 500 12.0 5000 189.2 74.3 149 51 196 1.15 1.15
AS 500 19.69 0.492 31.4 9.19 51.27 31.34 3.1 4.8 3.77 1.15
4.5
12.5 500 12.5 5500 194.5 76.3 153 51 201 1.15 1.15
AS 500 19.69 0.500 31.4 9.28 51.81 31.54 3.1 4.9 3.77 1.15
4.5
12.7 500 12.7 5500 196.4 77.1 154 51 204 1.15 1.15
AS 500 19.69 0.512 34.2 9.51 53.09 32.36 3.3 5.1 3.77 1.15
4.5
13.0 500 13.0 6000 201.2 79.0 158 54 213 1.15 1.15
Pre-bent piles are available to achieve a tighter radius in the cells and arcs.
Junction Piles
9.84"
(250 mm) 30° - 45°
9.84"
(250 mm) 120°
Y Pile
5.91"
(150 mm)
9.84"
(250 mm)
120° Y Pile
90°
10.16"
(258 mm)
9.84"
(250 mm)
90° T Pile
Combined Wall
Systems
Combined wall systems are used when regular sheet piles are not strong enough to carry the required loads. The two
main components of a combined wall system are the king pile (HZ®-M or Pipe) and a pair of intermediary sheet piles. The
connector is the third component and is welded to or interlocked with the king pile and connects the king pile to the sheet
pile. The intermediary sheet piles transfer the soil and water pressures to the king piles, which carry most of the load. The
sheet piles are usually shorter, varying from 60% to 100% of the length of the king pile. The king piles are often designed to
carry substantial vertical loads in addition to the normal bending loads.
There are a wide variety of HZ®-M and Pipe solutions which give the designer a great deal of flexibility. Each type of
system, beam and pipe, has their own advantages. The HZ®-M system is fully interlocking and does not rely on any welded
connections. The HZ®-M system also has a shallower depth than the pipe system which reduces the encroachment into
waterways. The Pipe-Z system has a much greater range of strengths than the HZ®-M system because of the very large pipes
that can be manufactured for the system. It also usually has higher strength to weight and stiffness to weight ratios than the
HZ®-M system. Whichever system is chosen, the engineer can rest assured that both systems have proven themselves on
large infrastructure projects around the world.
Combined wall systems provide an ideal solution for applications such as: large capacity retaining walls with deep
excavations, breakwaters, deep cofferdams, and other structures that require retaining walls to resist large loads.
Combined Wall
Systems
Corpus Christi, TX
Miami, FL Everett, WA
Pipe-Z
Pipe-Z Combined Wall Systems
Pipe-Z WEIGHT
System (Sheet Pile Length/Pipe Length) Cross Both
Sheet Pile
Section Outside Wall Pipe System System Section Sectional Sides of
Combination Diameter Thickness Weight Width Inertia Modulus 100% 80% 60% Area Wall
Sample
in in lb/ft in in4/ft in3/ft lb/ft2 lb/ft2 lb/ft2 in2/ft ft2/ft
mm mm kg/m mm cm4/m cm3/m kg/m2 kg/m2 kg/m2 cm2/m m2/m
PAZ30/AZ14-770 AZ 14-770 30.00 0.312 99.02 92.98 525 35.0 28.4 25.3 22.2 8.35 20.98
762.00 7.9 147.36 2362 71696 1882 138.7 123.4 108.2 176.7 6.40
PAZ30/AZ18 AZ 18 30.00 0.375 118.76 81.96 712 47.5 34.1 30.8 27.4 10.02 20.06
762.00 9.5 176.74 2082 97257 2553 166.6 150.2 133.9 212.2 6.12
PAZ36/AZ14-770 AZ 14-770 36.00 0.375 142.81 98.98 912 50.7 32.0 29.1 26.1 9.40 22.55
914.40 9.5 212.53 2514 124510 2723 156.2 141.9 127.5 199.0 6.87
PAZ36/NZ19 NZ 19 36.00 0.500 189.75 93.48 1295 71.9 40.3 37.1 33.9 11.84 22.71
914.40 12.7 282.38 2374 176814 3867 196.8 181.2 165.6 250.7 6.92
PAZ42/AZ14-770 AZ 14-770 42.00 0.438 194.60 104.98 1510 71.9 36.1 33.3 30.5 10.60 24.12
1066.80 11.1 289.61 2666 206230 3866 176.2 162.7 149.2 224.4 7.35
PAZ42/NZ19 NZ 19 42.00 0.500 221.82 99.48 1850 88.1 41.7 38.7 35.7 12.27 24.28
1066.80 12.7 330.11 2527 252623 4736 203.8 189.2 174.5 259.6 7.40
PAZ42/AZ23-800 AZ 23-800 42.00 0.625 276.44 107.35 2181 103.9 46.7 43.5 40.4 13.72 25.76
1066.80 15.9 411.39 2727 297846 5584 228.0 212.6 197.2 290.5 7.85
PAZ42/AZ38-700N AZ 38-700N 42.00 0.750 330.72 99.48 2879 137.1 62.1 57.7 53.2 18.25 25.44
1066.80 19.1 492.18 2527 393193 7372 303.2 281.5 259.8 386.3 7.75
PAZ48/AZ14-770 AZ 14-770 48.00 0.500 253.89 110.98 2369 98.7 40.5 37.9 35.3 11.91 25.69
1219.20 12.7 377.84 2819 323472 5306 198.0 185.2 172.4 252.2 7.83
PAZ48/NZ19 NZ 19 48.00 0.625 316.52 105.48 3117 129.9 50.1 47.3 44.5 14.73 25.85
1219.20 15.9 471.05 2679 425697 6983 244.8 231.0 217.2 311.9 7.88
PAZ48/AZ23-800 AZ 23-800 48.00 0.750 378.83 113.35 3515 146.5 55.1 52.1 49.1 16.18 27.33
1219.20 19.1 563.77 2879 479970 7874 268.9 254.3 239.7 342.5 8.33
PAZ48/AZ38-700N AZ 38-700N 48.00 0.875 440.80 105.48 4455 185.6 71.1 66.9 62.7 20.89 27.01
1219.20 22.2 655.99 2679 608417 9981 347.1 326.7 306.2 442.2 8.23
PAZ54/AZ14-770 AZ 14-770 54.00 0.563 321.61 116.98 3549 131.5 45.4 42.9 40.4 13.34 27.27
1371.60 14.3 478.62 2971 484705 7068 221.7 209.6 197.5 282.4 8.31
PAZ54/NZ19 NZ 19 54.00 0.625 356.61 111.48 4158 154.0 51.8 49.1 46.4 15.21 27.42
1371.60 15.9 530.71 2832 567781 8279 252.7 239.7 226.6 321.9 8.36
PAZ54/AZ23-800 AZ 23-800 54.00 0.750 426.93 119.35 4686 173.5 57.1 54.3 51.5 16.79 28.91
1371.60 19.1 635.36 3032 639866 9330 279.0 265.1 251.2 355.4 8.81
PAZ54/AZ38-700N AZ 38-700N 54.00 0.875 496.92 111.48 5891 218.2 73.3 69.3 65.4 21.54 28.58
1371.60 22.2 739.51 2832 804396 11730 357.9 338.6 319.2 456.0 8.71
Size Range: The combinations above are just a sample of the thousands of possibilities that are available with the Pipe-Z System.
System Width: For a given strength or stiffness requirement, using larger diameter pipes and wider sheet piles (new 800 mm sections) will maximize the efficiency of the wall.
A larger system width reduces the number of connectors to weld, piles to drive, and tierods to install.
Contact your local Skyline Steel representative to check on pricing and availability of your system.
Pipe-Z System
PROPERTIES OF PIPE PILE PROPERTIES OF COMBINED WALL COATING
Pipe-Z WEIGHT
System (Sheet Pile Length/Pipe Length) Cross Both
Sheet Pile
Section Outside Wall Pipe System System Section Sectional Sides of
Combination Diameter Thickness Weight Width Inertia Modulus 100% 80% 60% Area Wall
Sample
in in lb/ft in in4/ft in3/ft lb/ft2 lb/ft2 lb/ft2 in2/ft ft2/ft
mm mm kg/m mm cm4/m cm3/m kg/m2 kg/m2 kg/m2 cm2/m m2/m
PAZ60/AZ14-770 AZ 14-770 60.00 0.625 396.70 122.98 5098 169.9 50.5 48.2 45.8 14.85 28.84
1524.00 15.9 590.37 3124 696115 9136 246.7 235.1 223.6 314.2 8.79
PAZ60/NZ19 NZ 19 60.00 0.750 475.04 117.48 6391 213.0 61.2 58.7 56.1 17.99 28.99
1524.00 19.1 706.95 2984 872780 11454 298.9 286.5 274.1 380.7 8.84
PAZ60/AZ23-700 AZ 23-800 60.00 0.875 553.04 125.35 7004 233.5 66.5 63.8 61.1 19.53 30.48
1524.00 22.2 823.03 3184 956387 12551 324.6 311.4 298.1 413.5 9.29
PAZ60/AZ38-700N AZ 38-700N 60.00 1.000 630.71 117.48 8567 285.6 83.2 79.5 75.7 24.46 30.15
1524.00 25.4 938.62 2984 1169817 15352 406.4 388.0 369.6 517.7 9.19
PAZ66/AZ14-770 AZ 14-770 66.00 0.688 480.35 128.98 7084 214.7 56.0 53.7 51.4 16.44 30.41
1676.40 17.5 714.86 3276 967362 11541 273.2 262.2 251.2 348.0 9.27
PAZ66/NZ19 NZ 19 66.00 0.750 523.14 123.48 8079 244.8 62.9 60.5 58.1 18.49 30.56
1676.40 19.1 778.54 3136 1103222 13162 307.2 295.4 283.6 391.3 9.32
PAZ66/AZ23-800 AZ 23-800 66.00 0.875 609.16 131.35 8866 268.7 68.6 66.0 63.4 20.15 32.05
1676.40 22.2 906.56 3336 1210754 14445 334.8 322.2 309.5 426.5 9.77
PAZ66/AZ38-700N AZ 38-700N 66.00 1.000 694.85 123.48 10793 327.1 85.4 81.8 78.3 25.10 31.72
1676.40 25.4 1034.08 3136 1473880 17584 417.1 399.6 382.1 531.3 9.67
PAZ72/AZ14-770 AZ 14-770 72.00 0.750 571.25 134.98 9548 265.2 61.5 59.4 57.2 18.09 31.98
1828.80 19.1 850.13 3428 1303904 14260 300.5 290.0 279.5 382.8 9.75
PAZ72/NZ19 NZ 19 72.00 0.813 618.68 129.48 10796 299.9 68.9 66.6 64.2 20.23 32.13
1828.80 20.7 920.73 3289 1474260 16123 336.2 324.9 313.7 428.2 9.79
PAZ72/AZ23-800 AZ 23-800 72.00 0.875 665.29 137.35 10989 305.2 70.5 68.0 65.5 20.71 33.62
1828.80 22.2 990.08 3489 1500565 16411 344.1 332.0 320.0 438.3 10.25
PAZ72/AZ38-700N AZ 38-700N 72.00 1.000 758.99 129.48 13324 370.1 87.4 84.0 80.6 25.68 33.29
1828.80 25.4 1129.53 3289 1819541 19899 426.8 410.1 393.4 543.6 10.15
PAZ78/AZ23-800 AZ 23-800 78.00 0.875 721.41 143.35 13375 343.0 72.2 69.9 67.5 21.22 35.19
1981.20 22.2 1073.60 3641 1826459 18438 352.6 341.1 329.5 449.2 10.73
PAZ78/AZ38-700N AZ 38-700N 78.00 1.000 823.13 135.48 16165 414.5 89.2 86.0 82.7 26.22 34.86
1981.20 25.4 1224.98 3441 2207429 22284 435.6 419.7 403.7 554.9 10.63
PAZ84/AZ23-800 AZ 23-800 84.00 0.875 777.53 149.35 16030 381.7 73.8 71.6 69.3 21.69 36.76
2133.60 22.2 1157.12 3794 2188975 20520 360.5 349.4 338.3 459.2 11.20
PAZ84/AZ38-700N AZ 38-700N 84.00 1.000 887.27 141.48 19319 460.0 90.9 87.8 84.6 26.70 36.43
2133.60 25.4 1320.44 3594 2638067 24729 443.7 428.4 413.2 565.2 11.11
Size Range: The combinations above are just a sample of the thousands of possibilities that are available with the Pipe-Z System.
System Width: For a given strength or stiffness requirement, using larger diameter pipes and wider sheet piles (new 800 mm sections) will maximize the efficiency of the wall.
A larger system width reduces the number of connectors to weld, piles to drive, and tierods to install.
Contact your local Skyline Steel representative to check on pricing and availability of your system.
*Availability is dependent on pipe diameter and thickness. **Not available for AZ 36-700N and larger.
NZ 90 feet 27.4 m
DIMENSIONS
h h1 w tmax t s r
SECTION in in in in in in in Suitable Connector
mm mm mm mm mm mm mm
Solution 100
Sectional
v1 v2 v3 v4 u Area Mass y-y z-z y-y* y-y** z-z Waterside Landside
SECTION in in in in in in2 lb/ft in4 in4 in3 in3 in3 ft2/ft ft2/ft
mm mm mm mm mm cm2 kg/m cm4 cm4 cm3 cm3 cm3 m2/m m2/m
11.81 12.44 9.06 40.44 137.63 4330.3 926.9 366.9 102.5 1.52 8.45
HZ 680M LT 299.9 - 315.9 - 230.0 260.9 204.8 180430 38620 6015 - 1680 0.462 2.573
15.82 16.36 9.02 45.82 155.92 8571.4 960.8 541.9 106.5 1.51 9.73
HZ 880M A 401.7
-
415.7
-
229.0 295.6 232.0 356770 39990 8880
-
1745 0.459 2.966
15.89 16.36 9.06 50.87 173.13 9435.8 1027.5 593.8 113.5 1.51 9.74
HZ 880M B 403.7
-
415.7
-
230.0 328.2 257.6 392750 42770 9730
-
1860 0.461 2.967
15.97 16.36 9.06 53.11 180.76 10012.7 1065.5 627.0 117.8 1.51 9.74
HZ 880M C 405.7
-
415.7
-
230.0 342.7 269.0 416760 44350 10275
-
1930 0.461 2.967
20.62 21.17 8.94 58.00 197.39 16943.9 944.9 821.7 105.9 1.49 11.14
HZ 1080M A 523.7
-
537.7
-
227.0 374.2 293.8 705260 39330 13465
-
1735 0.455 3.396
20.74 21.17 8.94 61.63 209.72 18512.5 1016.5 892.8 113.8 1.49 11.14
HZ 1080M B 526.7
-
537.7
-
227.0 397.6 312.1 770550 42310 14630
-
1865 0.455 3.396
20.85 21.17 8.98 68.14 231.88 20396.5 1080.2 977.9 120.2 1.50 11.15
HZ 1080M C 529.7
-
537.7
-
228.0 439.6 345.1 848970 44960 16025
-
1970 0.457 3.397
21.01 21.17 9.00 73.41 249.82 22231.8 1127.7 1058.2 125.4 1.50 11.15
HZ 1080M D 533.7
-
537.7
-
228.5 473.6 371.8 925360 46940 17340
-
2055 0.457 3.397
21.17 21.17 9.02 77.63 264.18 23617.8 1152.0 1115.8 127.8 1.50 11.15
HZ 1180M A 537.7
-
537.7
-
229.0 500.8 393.1 983050 47950 18285
-
2095 0.457 3.397
21.25 21.25 9.02 80.46 273.83 24893.7 1228.9 1171.7 136.4 1.50 11.18
HZ 1180M B 539.7
-
539.7
-
229.0 519.1 407.5 1036160 51150 19200
-
2235 0.457 3.407
21.33 21.33 9.04 84.98 289.21 26434.9 1314.9 1239.4 145.5 1.51 11.21
HZ 1180M C 541.7
-
541.7
-
229.5 548.3 430.4 1100310 54730 20310
-
2385 0.459 3.416
21.41 21.41 9.06 89.51 304.63 27991.5 1401.9 1307.7 154.7 1.53 11.24
HZ 1180M D 543.7
-
543.7
-
230.0 577.5 453.3 1165100 58350 21430
-
2535 0.460 3.425
Solution 102
Sectional
v1 v2 v3 v4 u Area Mass y-y z-z y-y* y-y** z-z Waterside Landside
SECTION in in in in in in2 lb/ft in4 in4 in3 in3 in3 ft2/ft ft2/ft
mm mm mm mm mm cm2 kg/m cm4 cm4 cm3 cm3 cm3 m2/m m2/m
11.96 11.66 12.59 12.29 9.06 39.96 136.01 4256.9 894.7 356.2 98.8 1.57 8.45
HZ 680M LT 303.7 296.2 319.7 312.1 230.0 257.8 202.4 177370 37280 5840
-
1620 0.478 2.573
15.99 15.64 16.54 16.19 9.02 45.32 154.24 8441.2 928.3 527.9 102.8 1.57 9.73
HZ 880M A 406.2 397.2 420.1 411.2 229.0 292.4 229.5 351350 38640 8650
-
1685 0.478 2.966
16.07 15.72 16.54 16.19 9.06 50.33 171.30 9293.1 991.8 578.5 109.5 1.58 9.74
HZ 880M B 408.1 399.3 420.0 411.2 230.0 324.7 254.9 386810 41280 9480
-
1795 0.481 2.967
16.14 15.81 16.53 16.20 9.06 52.58 178.93 9870.2 1030.0 611.8 113.8 1.58 9.74
HZ 880M C 409.9 401.5 419.9 411.4 230.0 339.2 266.3 410830 42870 10025
-
1865 0.481 2.967
20.79 20.44 21.34 20.99 8.94 57.52 195.75 16729.6 913.7 804.6 102.2 1.55 11.14
HZ 1080M A 528.2 519.2 542.1 533.2 227.0 371.1 291.3 696340 38030 13185
-
1675 0.473 3.396
20.92 20.55 21.35 20.98 8.94 61.09 207.89 18273.4 981.9 873.6 109.8 1.56 11.14
HZ 1080M B 531.4 522.0 542.3 533.0 227.0 394.1 309.4 760600 40870 14315
-
1800 0.475 3.396
21.02 20.69 21.33 21.00 8.98 67.60 230.05 20157.5 1045.1 959.0 116.6 1.56 11.15
HZ 1080M C 533.9 525.5 541.9 533.4 228.0 436.1 342.4 839020 43500 15715
-
1910 0.475 3.397
21.17 20.86 21.32 21.01 9.00 72.87 247.99 21993.0 1038.9 1038.9 121.4 1.56 11.15
HZ 1080M D 537.6 529.8 541.6 533.7 228.5 470.1 369.0 915420 45480 17025
-
1990 0.475 3.397
21.32 21.02 21.32 21.02 9.02 77.09 262.34 23377.3 1116.4 1096.6 123.9 1.57 11.15
HZ 1180M A 541.4 534.0 541.6 534.0 229.0 497.3 390.4 973040 46470 17970
-
2030 0.477 3.397
21.44 21.06 21.44 21.06 9.02 79.75 271.39 24572.3 1181.5 1146.3 131.2 1.58 11.18
HZ 1180M B 544.5 534.9 544.5 534.9 229.0 514.5 403.9 1022780 49180 18785
-
2150 0.481 3.407
21.51 21.15 21.51 21.15 9.04 84.26 286.77 26111.3 1267.3 1214.1 140.4 1.58 11.21
HZ 1180M C 546.3 537.1 546.3 537.1 229.5 543.6 426.8 1086840 52750 19895
-
2300 0.481 3.416
21.67 21.14 21.67 21.14 9.06 88.42 300.92 27494.2 1329.8 1269.0 146.8 1.60 11.24
HZ 1180M D 550.4 537.0 550.4 537.0 230.0 570.5 447.8 1144400 55350 20795
-
2405 0.487 3.419
Solution 104
Sectional
v1 v2 v3 v4 u Area Mass y-y z-z y-y* y-y** z-z Waterside Landside
SECTION in in in in in in2 lb/ft in4 in4 in3 in3 in3 ft2/ft ft2/ft
mm mm mm mm mm cm2 kg/m cm4 cm4 cm3 cm3 cm3 m2/m m2/m
11.81 12.44 9.06 39.48 134.33 4185.1 862.3 354.7 95.2 1.57 8.51
HZ 680M LT 299.9
-
315.9
-
230.0 254.7 199.9 174380 35930 5815
-
1560 0.478 2.59
15.82 16.36 9.02 44.83 152.57 8313.6 895.9 525.7 99.5 1.57 9.79
HZ 880M A 401.7
-
415.7
-
229.0 289.2 227.0 346040 37290 8615
-
1630 0.478 2.984
15.89 16.36 9.06 49.80 169.47 9153.8 956.2 576.1 105.6 1.58 9.80
HZ 880M B 403.7
-
415.7
-
230.0 321.3 252.2 381010 39800 9440
-
1730 0.481 2.987
15.97 16.39 9.06 52.04 177.01 9730.8 994.2 609.3 109.8 1.58 9.80
HZ 880M C 405.7
-
415.7
-
230.0 335.7 263.6 405030 41380 9985
-
1800 0.480 2.987
20.62 21.17 8.94 57.04 194.10 16518.6 882.4 801.2 98.9 1.55 11.20
HZ 1080M A 523.7
-
537.7
-
227.0 368.0 288.9 687560 36730 13130
-
1620 0.473 3.414
20.74 21.17 8.94 60.55 206.06 18038.5 947.3 869.9 105.9 1.56 11.20
HZ 1080M B 526.7
-
537.7
-
227.0 390.6 306.7 750820 39430 14255
-
1735 0.475 3.415
20.85 21.17 8.98 67.06 228.22 19922.3 1010.3 955.3 112.6 1.56 11.21
HZ 1080M C 529.7
-
537.7
-
228.0 432.7 339.6 829230 42050 15655
-
1845 0.476 3.417
21.01 21.17 9.00 72.33 246.16 21757.8 1057.6 1035.6 117.5 1.56 11.21
HZ 1080M D 533.7
-
537.7
-
228.5 466.7 366.3 905630 44020 16970
-
1925 0.477 3.417
21.17 21.17 9.02 76.54 260.49 23139.9 1080.9 1093.2 119.9 1.57 11.21
HZ 1180M A 537.7
-
537.7
-
229.0 493.8 387.7 963160 44990 17915
-
1965 0.477 3.418
21.25 21.25 9.02 79.03 268.94 24256.4 1134.5 1141.5 125.7 1.58 11.25
HZ 1180M B 539.7
-
539.7
-
229.0 509.8 400.2 1009630 47220 18705
-
2060 0.481 3.430
21.33 21.33 9.04 83.55 284.32 25793.0 1220.0 1209.5 134.9 1.58 11.28
HZ 1180M C 541.7
-
541.7
-
229.5 539.0 423.1 1073590 50780 19820
-
2210 0.482 3.439
21.41 21.41 9.06 87.33 297.20 27009.1 1257.7 1261.7 138.8 1.60 11.29
HZ 1180M D 543.7
-
543.7
-
230.0 563.4 442.3 1124210 52350 20675
-
2275 0.487 3.440
Delivery Form
Sectional
v1 v2 v3 v4 u1 u2 Area Mass y-y z-z y-y* y-y** z-z Waterside Landside
SECTION in in in in in in in2 lb/ft in4 in4 in3 in3 in3 ft2/ft ft2/ft
mm mm mm mm mm mm cm2 kg/m cm4 cm4 cm3 cm3 cm3 m2/m m2/m
10.30 13.31 11.74 9.05 11.14 46.33 157.72 5052.2 1470.5 379.7 430.7 132.1 2.04 8.62
HZ 680M LT 261.7 338.1 298.1
-
229.8 282.9 298.9 234.7 210510 61270 6225 7060 2165 0.621 2.623
14.02 17.61 15.37 9.01 11.14 51.70 175.93 9868.7 1504.9 560.5 642.0 135.2 2.04 9.90
HZ 880M A 356.2 447.2 390.5
-
228.9 282.9 333.5 261.8 410770 62640 9185 10520 2215 0.621 3.017
14.27 17.51 15.55 9.05 11.18 56.71 192.98 10738.2 1573.2 613.0 690.8 140.7 2.05 9.91
HZ 880M B 362.5 444.9 394.9
-
229.9 283.9 365.8 287.2 446960 65480 10045 11320 2305 0.624 3.019
14.41 17.53 15.61 9.05 11.18 58.95 200.61 11320.8 1611.1 645.3 725.3 144.0 2.05 9.90
HZ 880M C 366.1 445.3 396.4
-
229.9 283.9 380.3 298.5 471210 67060 10580 11885 2360 0.624 3.019
18.72 22.51 20.07 8.93 11.06 63.89 217.43 19207.5 1480.7 853.1 956.9 133.9 2.02 11.31
HZ 1080M A 475.6 571.8 509.9
-
226.9 280.9 412.2 323.6 799480 61630 13980 15680 2195 0.617 3.447
18.96 22.51 20.19 8.93 11.06 67.46 229.58 20767.9 1548.9 922.4 1028.6 140.1 2.03 11.31
HZ 1080M B 481.5 571.9 512.9
-
226.9 280.9 435.2 341.6 864430 64470 15115 16855 2295 0.618 3.447
19.23 22.48 20.35 8.97 11.10 73.97 251.74 22670.7 1616.9 1008.7 1114.3 145.3 2.03 11.32
HZ 1080M C 488.5 570.9 516.8
-
227.9 281.9 477.2 374.6 943630 67300 16530 18260 2390 0.619 3.449
19.50 22.53 20.46 8.99 11.12 79.24 269.67 24519.0 1666.9 1088.7 1198.8 149.8 2.03 11.32
HZ 1080M D 495.3 572.1 519.6
-
228.4 282.4 511.2 401.3 1020560 69380 17840 19645 2455 0.620 3.449
19.73 22.61 20.53 9.01 11.14 83.46 284.02 25912.4 1693.0 1146.3 1262.0 151.9 2.04 11.32
HZ 1180M A 501.2 574.2 521.5
-
228.9 282.9 538.4 422.7 1078560 70470 18785 20680 2490 0.621 3.449
19.90 22.60 20.62 9.01 11.14 86.12 293.07 27124.2 1758.1 1200.3 1315.4 157.7 2.04 11.33
HZ 1180M B 505.5 573.9 523.8
-
228.9 282.9 555.6 436.1 1129000 73180 19670 21555 2585 0.622 3.454
19.90 22.75 20.66 9.03 11.16 91.33 310.81 28917.9 1897.5 1271.1 1399.6 170.0 2.08 11.36
HZ 1180M C 505.5 577.9 524.8
-
229.4 283.4 589.2 462.5 1203660 78980 20830 22935 2785 0.635 3.463
20.13 22.68 20.81 9.05 11.18 95.49 324.96 30333.2 1962.6 1337.3 1457.9 175.4 2.10 11.38
HZ 1180M D 511.2 576.2 528.5
-
229.9 283.9 616.1 483.6 1262570 81690 21915 23890 2875 0.641 3.468
Delivery Form
Sectional
v1 v2 v3 v4 u1 u2 Area Mass y-y z-z y-y* y-y** z-z Waterside Landside
SECTION in in in in in in in2 lb/ft in4 in4 in3 in3 in3 ft2/ft ft2/ft
mm mm mm mm mm mm cm2 kg/m cm4 cm4 cm3 cm3 cm3 m2/m m2/m
11.79 11.83 13.22 13.26 9.05 11.14 52.08 177.27 5980.6 1983.4 506.0 451.4 178.1 2.04 9.37
HZ 680M LT 299.5 300.4 335.8 336.9 229.8 282.9 336.0 263.8 249190 82640 8295 7400 2920 0.621 2.853
15.79 15.84 17.14 17.20 9.01 11.14 57.44 195.49 11485.9 2013.5 725.0 667.9 180.9 2.04 10.67
HZ 880M A 401.1 402.4 435.4 436.8 228.9 282.9 370.6 290.9 478080 83810 11880 10945 2965 0.621 3.253
15.87 15.92 17.14 17.19 9.05 11.18 62.41 212.38 12326.0 2083.2 774.4 716.7 186.4 2.05 10.68
HZ 880M B 403.1 404.3 435.4 436.8 229.9 283.9 402.6 316.1 513050 86710 12690 11745 3055 0.624 3.256
15.95 16.00 17.14 17.19 9.05 11.18 64.65 220.02 12903.21 2121.3 806.7 750.6 189.8 2.05 10.68
HZ 880M C 405.1 406.3 435.5 436.7 229.9 283.9 417.1 327.4 537070 88290 13220 12300 3110 0.624 3.255
20.59 20.65 21.94 22.00 8.93 11.06 69.65 237.02 21900.5 1981.6 1060.6 995.3 179.1 2.02 12.08
HZ 1080M A 522.9 524.5 557.3 558.9 226.9 280.9 449.3 352.7 911570 82480 17380 16310 2935 0.617 3.683
20.71 20.77 21.94 22.00 8.93 11.06 73.16 248.98 23420.1 2046.4 1128.0 1064.6 185.2 2.03 12.09
HZ 1080M B 526.0 527.4 557.3 558.9 226.9 280.9 472.0 370.5 974820 85180 18485 17445 3035 0.618 3.684
20.83 20.88 21.94 22.00 8.97 11.10 79.67 271.14 25304.3 2118.5 1211.9 1150.3 191.0 2.03 12.09
HZ 1080M C 529.0 530.4 557.3 558.9 227.9 281.9 514.0 403.5 1053250 88180 19860 18850 3130 0.619 3.685
20.99 21.04 21.94 22.00 8.99 11.12 84.94 289.07 27139.6 2170.7 1290.0 1233.6 195.3 2.03 12.09
HZ 1080M D 533.1 534.3 557.3 558.9 228.4 282.4 548.0 430.2 1129640 90350 21140 20215 3200 0.620 3.686
21.15 21.19 21.95 22.00 9.01 11.14 89.15 303.41 28521.8 2198.5 1345.9 1296.8 197.4 2.04 12.10
HZ 1180M A 537.1 538.3 557.4 558.9 228.9 282.9 575.2 451.5 1187170 91510 22055 21250 3235 0.621 3.687
21.22 21.27 21.95 22.00 9.01 11.14 91.64 311.86 29638.2 2252.1 1393.5 1347.4 202.3 2.04 12.10
HZ 1180M B 539.1 540.3 557.4 558.9 228.9 282.8 591.2 464.1 1233640 93740 22835 22080 3315 0.622 3.688
21.49 21.16 22.25 21.92 9.03 11.16 98.44 334.99 32120.9 2538.7 1494.5 1443.5 227.6 2.08 12.21
HZ 1180M C 545.9 537.5 565.2 556.8 229.4 283.4 635.1 498.5 1336980 105670 24490 23655 3730 0.635 3.722
21.57 21.25 22.25 21.93 9.05 11.18 102.22 347.87 33337.1 2582.2 1546.0 1498.4 231.0 2.10 12.23
HZ 1180M D 547.8 539.6 565.1 556.9 229.9 283.9 659.5 517.7 1387600 107480 25335 24555 3785 0.641 3.728
Delivery Form
Form a Form b
Sectional
v1 v2 v3 v4 u1 u2 Area Mass y-y z-z y-y* y-y** z-z Waterside Landside
SECTION in in in in in in in2 lb/ft in4 in4 in3 in3 in3 ft2/ft ft2/ft
mm mm mm mm mm mm cm2 kg/m cm4 cm4 cm3 cm3 cm3 m2/m m2/m
10.98 12.63 12.41 14.07 18.38 20.47 91.56 311.61 10102.6 10849.4 800.3 718.6 530.4 3.75 10.39
HZ 680M LT 279 320.9 315.3 357.4 466.8 519.9 590.7 463.7 420940 452060 13120 11780 8695 1.144 3.163
14.83 16.80 16.19 18.16 18.30 20.43 102.27 348.05 19700.5 11783.3 1172.9 1085.0 576.7 3.75 11.68
HZ 880M A 376.7 426.7 411.2 461.2 464.8 518.9 659.8 518.0 820000 490460 19220 17780 9450 1.144 3.559
15.00 16.79 16.27 18.07 18.38 20.51 112.20 381.85 21389.7 12853.1 1273.9 1183.9 626.7 3.77 11.70
HZ 880M B 380.9 426.5 413.4 458.9 466.9 520.9 723.9 568.3 890310 534990 20875 19400 10270 1.150 3.565
15.11 16.83 16.31 18.03 18.38 20.51 116.69 397.12 22547.0 13319.7 1339.5 1250.4 649.6 3.77 11.69
HZ 880M C 383.8 427.6 414.3 458.1 466.9 520.9 752.8 591.0 938480 554410 21950 20490 10645 1.150 3.565
19.58 21.65 20.94 23.01 18.14 20.27 126.68 431.12 38.283.1 13659.9 1767.9 1663.8 674.0 3.73 13.07
HZ 1080M A 497.4 550.0 531.8 584.4 460.9 514.9 817.3 641.6 1593470 568570 28970 27265 11045 1.136 3.985
19.75 21.72 20.99 22.95 18.14 20.27 133.71 455.04 41329.7 14385.9 1903.0 1800.5 709.7 3.73 13.08
HZ 1080M B 501.8 551.6 533.2 583.1 460.9 514.9 862.6 677.2 1720280 598790 31185 29505 11630 1.138 3.987
19.96 21.75 21.08 22.87 18.22 20.35 146.73 499.36 45109.3 15733.3 2074.2 1972.6 773.2 3.74 13.09
HZ 1080M C 507.0 552.4 535.4 580.8 462.9 516.9 946.7 743.1 1877600 654870 33990 32325 12670 1.141 3.990
20.18 21.85 21.14 22.81 18.26 20.39 157.27 535.23 48787.8 16792.3 2233.2 2139.2 823.5 3.75 13.10
HZ 1080M D 512.5 554.9 536.9 579.3 463.9 517.9 1014.7 796.5 2030710 698950 36595 35055 13495 1.142 3.991
20.38 21.96 21.18 22.77 18.30 20.43 165.70 563.90 51557.9 17628.8 2347.6 2264.9 862.9 3.75 13.10
HZ 1180M A 517.6 557.8 538.0 578.2 464.9 518.9 1069.0 839.2 2146010 733770 38470 37115 14140 1.144 3.993
20.48 22.02 21.20 22.74 18.30 20.43 170.66 580.80 53793.9 18164.3 2443.4 2365.3 889.1 3.76 13.13
HZ 1180M B 520.2 559.2 538.6 577.7 464.9 518.9 1101.0 864.3 2239080 756060 40040 38760 14570 1.147 4.002
20.53 22.12 21.29 22.88 18.38 20.51 181.98 619.31 57800.8 19543.1 2612.4 2525.8 952.9 3.82 13.17
HZ 1180M C 521.4 562.0 540.7 581.3 466.9 520.9 1174.1 921.6 2405860 813450 42810 41390 15615 1.164 4.015
20.64 22.17 21.32 22.85 18.42 20.55 189.55 645.07 60237.4 20355.4 2716.8 2635.9 990.7 3.86 13.20
HZ 1180M D 524.2 563.2 541.5 580.5 467.9 521.9 1222.9 960.0 2507280 847260 44520 43195 16235 1.176 4.025
Delivery Form
Form a Form b
Sectional
v1 v2 v3 v4 u1 u2 Area Mass y-y z-z y-y* y-y** z-z Waterside Landside
SECTION in in in in in in in2 lb/ft in4 in4 in3 in3 in3 ft2/ft ft2/ft
mm mm mm mm mm mm cm2 kg/m cm4 cm4 cm3 cm3 cm3 m2/m m2/m
11.80 11.82 13.23 13.25 18.38 20.47 97.81 332.84 11061.1 13022.4 936.7 835.1 636.5 3.75 11.09
HZ 680M LT 299.7 300.2 336.0 336.6 466.8 519.9 631.0 495.3 460880 542600 15355 13690 10435 1.144 3.376
15.81 15.82 17.16 17.19 18.31 20.43 108.51 369.28 21379.6 13940.3 1351.1 1244.0 682.6 3.75 12.39
HZ 880M A 401.4 402.0 435.8 436.5 464.9 518.9 700.1 549.6 889890 580240 22135 20385 11180 1.144 3.776
15.88 15.91 17.16 17.18 18.38 20.50 118.44 403.08 23059.9 15028.4 1449.6 1341.9 732.9 3.77 12.41
HZ 880M B 403.4 404.0 435.8 436.5 466.9 520.9 764.1 599.9 959830 625530 23755 21990 12010 1.150 3.782
15.96 15.98 17.16 17.18 18.38 20.50 122.93 418.35 24213.8 15494.9 1514.9 1409.0 755.8 3.77 12.41
HZ 880M C 405.4 406.0 435.9 436.5 466.9 520.9 793.1 622.6 1007860 644950 24825 23090 12380 1.150 3.782
20.60 20.63 21.96 21.99 18.14 20.27 132.92 452.36 41095.0 15780.3 1991.5 1868.9 778.4 3.73 13.79
HZ 1080M A 523.3 524.1 557.7 558.5 460.9 514.9 857.6 673.2 1710510 656830 32635 30625 12755 1.136 4.202
20.72 20.75 21.96 21.99 18.14 20.27 139.95 476.27 44134.6 16506.6 2127.0 2007.1 814.4 3.73 13.79
HZ 1080M B 526.3 527.1 557.7 558.5 460.9 514.9 902.9 708.8 1837030 687060 34855 32890 13345 1.138 4.204
20.84 20.87 21.96 21.99 18.22 20.35 152.97 520.59 47902.7 17872.2 2295.4 2178.6 878.4 3.74 13.80
HZ 1080M C 529.4 530.1 557.8 558.5 462.9 516.9 986.9 774.7 1993870 743900 37615 35700 14395 1.141 4.208
21.00 21.02 21.96 21.99 18.26 20.39 163.51 556.46 51573.5 18940.1 2452.9 2345.8 929.1 3.75 13.81
HZ 1080M D 533.4 534.0 557.8 558.5 463.9 517.9 1054.9 828.1 2146660 788350 40195 38440 15225 1.142 4.209
21.16 21.18 21.96 21.99 18.30 20.43 171.94 585.13 54338.1 19785.8 2565.4 2471.5 968.8 3.75 13.81
HZ 1180M A 537.4 538.0 557.8 558.4 464.9 518.9 1109.3 870.8 2261730 823550 42040 40500 15875 1.144 4.210
21.24 21.26 21.96 21.99 18.30 20.43 176.90 602.03 56570.9 20321.3 2661.0 2573.1 995.0 3.76 13.82
HZ 1180M B 539.4 540.0 557.8 558.4 464.9 518.8 1141.3 895.9 2354670 845840 43605 42165 16305 1.147 4.213
21.41 21.24 22.17 22.00 18.38 20.51 189.81 645.94 61256.8 22283.7 2860.8 2762.9 1086.5 3.82 13.95
HZ 1180M C 543.9 539.5 563.2 558.8 466.9 520.9 1224.5 961.3 2549710 927520 46880 45275 17805 1.164 4.251
21.49 21.32 22.17 22.00 18.42 20.55 197.37 671.70 63689.1 23107.5 2963.9 2873.0 1124.7 3.86 13.99
HZ 1180M D 545.8 541.6 563.1 558.9 467.9 521.9 1273.4 999.6 2650950 961810 48570 47080 18430 1.176 4.264
AZ - Intermediary Piles
30.31 13.56 0.375 0.375 31.40 106.84 862.2 127.2 5.24 6.10
AZ 14-770 770 344.5 9.5 9.5 202.6 159.0 35890 2085 13.31 1.85
27.56 16.56 0.375 0.375 31.59 107.52 1324.5 159.8 6.47 6.10
AZ 19-700 700 420.5 9.5 9.5 203.8 160.0 55130 2620 16.44 1.86
27.56 18.11 0.480 0.480 40.63 138.24 2008.7 221.8 7.03 6.33
AZ 26-700 700 460.0 12.2 12.2 262.1 205.7 83610 3635 17.86 1.93
Connectors
2.43 3.19 1.24 3.21 10.89 1.4 2.3 1.1 1.3 0.39 0.20
RZD 16 61.8 80.5
-
31.5
HZ 880M / 1080M / 1180M A-B
20.7 16.2 57 94 18 22 0.12 0.06
2.43 3.19 1.51 3.16 10.82 1.6 2.3 1.1 1.3 0.26 0.33
RZU 16 61.8 80.5
-
38.3
HZ 880M / 1080M / 1180M A-B
20.4 16.1 68 94 18 22 0.08 0.10
2.43 2.69 0.48 1.28 3.12 10.75 2.0 1.3 1.5 1.0 0.33 0.30
RH 16 61.8 68.2 12.2 32.5
HZ 880M / 1080M / 1180M A-B
20.1 16.0 83 54 25 16 0.10 0.09
2.65 3.35 1.41 3.57 12.16 1.9 2.6 1.3 1.5 0.39 0.23
RZD 18 67.3 85.0
-
35.9
HZ 1180M C-D
23.0 18.1 78 110 22 25 0.12 0.07
2.65 3.35 1.66 3.50 12.03 2.2 2.6 1.3 1.5 0.30 0.33
RZU 18 67.3 85.0
-
42.1
HZ 1180M C-D
22.6 17.9 92 110 22 25 0.09 0.10
2.65 3.12 0.56 1.44 3.91 13.44 2.9 2.1 2.0 1.3 0.36 0.33
RH 20 67.3 79.2 14.2 36.5
HZ 1180M C-D
25.2 20.0 122 88 33 22 0.11 0.10
Without other specifications, all the connectors are offered in Grade S 430 GP.
81.38 in.
2067.1 mm
HZ 680M LT 11.45 871.7 65.5 74.3 31.38 35.17 38.95 8.09 14.66
242.4 119038 3521.5 3994.6 153.21 171.71 190.17 2.466 4.468
HZ 880M A 12.25 1581.7 89.8 102.9 34.10 37.89 41.68 8.09 15.95
265.4 215994 4827.9 5532.2 166.49 184.99 203.50 2.466 4.862
HZ 880M B 12.97 1708.2 97.6 109.8 36.58 40.37 44.15 8.10 15.96
281.0 233269 5247.3 5903.2 178.60 197.10 215.56 2.469 4.865
HZ 880M C 13.30 1794.0 102.3 114.9 37.70 41.49 45.28 8.10 15.96
288.2 244985 5500.0 6177.4 184.07 202.57 221.08 2.469 4.865
HZ 1080M A 14.07 2963.8 131.7 147.7 40.30 44.09 47.89 8.08 17.36
304.9 404731 7080.6 7940.8 196.76 215.27 233.82 2.463 5.291
HZ 1080M B 14.60 3194.3 141.9 158.2 42.09 45.89 49.68 8.08 17.36
316.3 436208 7629.0 8505.3 205.50 224.05 242.56 2.463 5.291
HZ 1080M C 15.55 3471.9 154.5 170.7 45.32 49.11 52.91 8.08 17.37
336.9 474116 8306.4 9177.4 221.27 239.77 258.33 2.463 5.294
HZ 1080M D 16.32 3742.8 166.2 182.9 47.94 51.73 55.52 8.09 17.37
353.6 511110 8935.4 9833.3 234.06 252.57 271.07 2.466 5.294
HZ 1180M A 16.93 3946.4 174.6 192.2 50.03 53.82 57.61 8.09 17.37
366.8 538913 9387.0 10333.3 244.27 262.77 281.28 2.466 5.294
HZ 1180M B 17.32 4125.0 182.6 200.0 51.37 55.16 58.95 8.09 17.39
375.3 563303 9817.1 10752.6 250.81 269.31 287.82 2.466 5.300
HZ 1180M C 18.08 4387.2 192.9 212.3 53.82 57.67 61.53 8.14 17.42
391.7 599108 10370.9 11413.9 262.77 281.57 300.41 2.481 5.310
HZ 1180M D 18.68 4593.6 202.5 220.8 55.87 59.73 63.59 8.16 17.43
404.7 627294 10887.0 11870.9 272.78 291.63 310.47 2.487 5.313
* Referring outside of HZ -M-flange (v2), ** Referring outside of connector (v3), *** Length of connectors = Length of AZ.
®
81.38 in.
2067.1 mm
HZ 680M LT 12.29 1008.5 85.3 76.1 33.02 37.43 41.84 8.09 15.41
260.1 137720 4586.0 4091.4 161.22 182.75 204.28 2.466 4.697
HZ 880M A 13.09 1820.1 114.9 105.8 35.73 40.15 44.56 8.09 16.72
283.6 248550 6177.4 5688.1 174.45 196.03 217.56 2.466 5.096
HZ 880M B 13.81 1942.0 122.0 112.9 38.19 42.60 47.01 8.10 16.73
299.2 265196 6559.1 6069.9 186.46 208.00 229.52 2.469 5.099
HZ 880M C 14.14 2026.9 126.8 117.9 39.31 43.72 48.13 8.10 16.73
306.4 276790 6817.2 6338.7 191.93 213.46 234.99 2.469 5.099
HZ 1080M A 14.92 3361.5 162.8 152.8 41.94 46.36 50.78 8.08 18.14
323.3 459040 8752.6 8215.0 204.77 226.35 247.93 2.463 5.529
HZ 1080M B 15.44 3586.0 172.7 162.9 43.70 48.13 52.55 8.08 18.14
334.5 489698 9284.9 8758.0 213.36 234.99 256.57 2.463 5.529
HZ 1080M C 16.39 3860.5 184.9 175.5 46.93 51.35 55.77 8.08 18.14
355.1 527183 9940.8 9435.4 229.13 250.71 272.29 2.463 5.529
HZ 1080M D 17.16 4129.2 196.3 187.7 49.55 53.97 58.39 8.09 18.15
371.8 563876 10553.7 10091.3 241.92 263.50 285.08 2.466 5.532
HZ 1180M A 17.77 4331.0 204.3 196.9 51.64 56.06 60.47 8.09 18.15
385.0 591434 10983.8 10586.0 252.13 273.71 295.24 2.466 5.532
HZ 1180M B 18.13 4495.5 211.3 204.4 52.88 57.30 61.72 8.09 18.15
392.8 613897 11360.1 10989.2 258.18 279.76 301.34 2.466 5.532
HZ 1180M C 19.13 4859.1 226.1 218.4 55.81 60.45 65.09 8.14 18.27
414.5 663550 12155.8 11741.9 272.49 295.14 317.80 2.481 5.569
HZ 1180M D 19.68 5035.9 233.5 226.4 57.68 62.32 66.96 8.16 18.29
426.4 687693 12553.7 12172.0 281.62 304.27 326.93 2.487 5.575
* Referring outside of HZ®-M-flange (highest value of v1; v2), ** Referring outside of connector (highest value of v3; v4), *** Length of connectors = Length of AZ.
99.92 in.
2538.0 mm
HZ 680M LT 14.73 1315.0 104.1 93.5 43.98 47.06 50.14 9.80 16.43
311.8 179575 5596.8 5026.9 214.73 229.77 244.80 2.987 5.008
HZ 880M A 16.04 2467.6 146.8 135.9 48.42 51.51 54.59 9.81 17.73
347.5 336971 7892.4 7306.4 236.41 251.49 266.53 2.990 5.404
HZ 880M B 17.21 2666.1 158.8 147.6 52.39 55.47 58.55 9.83 17.75
372.9 364078 8537.6 7935.4 255.79 270.83 285.86 2.996 5.410
HZ 880M C 17.74 2804.8 166.6 155.5 54.22 57.30 60.38 9.83 17.75
384.4 383018 8956.9 8360.2 264.72 279.76 294.80 2.996 5.410
HZ 1080M A 19.03 4712.4 217.6 204.8 58.57 61.67 64.76 9.78 19.13
412.3 643517 11698.9 11010.7 285.96 301.10 316.19 2.981 5.831
HZ 1080M B 19.88 5079.2 233.9 221.2 61.45 64.55 67.64 9.79 19.14
430.7 693606 12575.2 11892.4 300.02 315.16 330.25 2.984 5.834
HZ 1080M C 21.41 5525.4 254.1 241.6 66.68 69.77 72.86 9.80 19.15
463.9 754539 13661.2 12989.2 325.56 340.65 355.73 2.987 5.837
HZ 1080M D 22.66 5962.8 273.0 261.4 70.94 74.02 77.11 9.80 19.15
491.0 814269 14677.3 14053.7 346.36 361.40 376.48 2.987 5.837
HZ 1180M A 23.65 6290.6 286.4 276.3 74.32 77.41 80.49 9.81 19.15
512.4 859033 15397.8 14854.7 362.86 377.95 392.98 2.990 5.837
HZ 1180M B 24.25 6558.9 297.9 288.4 76.35 79.43 82.52 9.82 19.18
525.4 895672 16016.0 15505.3 372.77 387.81 402.90 2.993 5.846
HZ 1180M C 25.57 7028.7 317.7 307.1 80.73 83.87 87.00 9.87 19.23
554.0 959827 17080.5 16510.6 394.16 409.49 424.77 3.008 5.861
HZ 1180M D 26.45 7314.9 329.9 320.1 83.75 86.89 90.02 9.91 19.26
573.1 998910 17736.4 17209.6 408.90 424.23 439.51 3.021 5.870
* Referring outside of HZ®-M-flange (highest value of v1; v2), ** Referring outside of connector (highest value of v3; v4), *** Length of connectors = Length of AZ.
99.92 in.
2538.0 mm
HZ 680M LT 15.48 1430.0 121.0 107.9 45.50 49.09 52.68 9.80 17.13
327.7 195279 6505.4 5801.1 222.15 239.68 257.20 2.987 5.221
HZ 880M A 16.79 2669.1 168.6 155.3 49.95 53.54 57.14 9.81 18.44
363.8 364487 9064.5 8349.4 243.88 261.40 278.98 2.990 5.621
HZ 880M B 17.95 2866.2 180.2 166.7 53.92 57.51 61.10 9.83 18.46
388.9 391403 9688.1 8962.3 263.26 280.79 298.31 2.996 5.627
HZ 880M C 18.49 3004.5 188.0 174.8 55.75 59.34 62.93 9.83 18.46
400.6 410289 10107.5 9397.8 272.19 289.72 307.25 2.996 5.627
HZ 1080M A 19.78 5050.9 244.8 229.7 60.11 63.71 67.32 9.78 19.84
428.6 689741 13161.2 12349.4 293.48 311.06 328.68 2.981 6.047
HZ 1080M B 20.63 5416.8 261.1 246.4 62.99 66.59 70.20 9.79 19.85
447.0 739708 14037.5 13247.2 307.54 325.12 342.74 2.984 6.050
HZ 1080M C 22.16 5861.1 280.9 266.5 68.21 71.81 75.41 9.80 19.86
480.1 800381 15102.1 14327.9 333.03 350.61 368.18 2.987 6.053
HZ 1080M D 23.41 6297.4 299.6 286.4 72.47 76.06 79.66 9.80 19.86
507.2 859962 16107.4 15397.8 353.83 371.36 388.93 2.987 6.053
HZ 1180M A 24.40 6624.2 312.8 301.3 75.85 79.45 83.04 9.81 19.87
528.7 904589 16817.1 16198.8 370.33 387.91 405.43 2.990 6.056
HZ 1180M B 25.00 6892.1 324.2 313.5 77.88 81.47 85.07 9.82 19.88
541.7 941173 17430.0 16854.7 380.24 397.77 415.35 2.993 6.059
HZ 1180M C 26.50 7442.7 347.5 335.6 82.64 86.42 90.19 9.87 20.00
574.2 1016362 18682.7 18042.9 403.48 421.94 440.34 3.008 6.096
HZ 1180M D 27.39 7728.1 359.6 348.6 85.66 89.44 93.21 9.91 20.04
593.5 1055335 19333.2 18741.8 418.23 436.68 455.09 3.021 6.108
* Referring outside of HZ®-M-flange (highest value of v1; v2), ** Referring outside of connector (highest value of v3; v4), *** Length of connectors = Length of AZ.
75.87 in.
1927.1 mm
HZ 680M LT 12.31 1007.9 75.7 85.8 33.72 37.80 41.88 8.12 14.69
260.6 137638 4069.9 4612.9 164.63 184.55 204.47 2.475 4.478
HZ 880M A 13.17 1769.6 100.5 115.1 36.64 40.72 44.81 8.13 15.99
285.4 241653 5403.2 6188.1 178.89 198.81 218.78 2.478 4.874
HZ 880M B 13.94 1905.1 108.8 122.6 39.29 43.37 47.45 8.14 15.99
302.0 260157 5849.4 6591.4 191.83 211.75 231.67 2.481 4.874
HZ 880M C 14.30 1997.1 113.9 128.0 40.50 44.58 48.66 8.13 15.99
309.8 272720 6123.6 6881.7 197.74 217.66 237.58 2.478 4.874
HZ 1080M A 15.13 3252.7 144.5 162.0 43.29 47.38 51.48 8.11 17.40
327.8 444183 7768.8 8709.6 211.36 231.33 251.35 2.472 5.304
HZ 1080M B 15.69 3500.0 155.5 173.4 45.21 49.31 53.40 8.12 17.40
340.0 477954 8360.2 9322.5 220.73 240.75 260.72 2.475 5.304
HZ 1080M C 16.71 3797.5 169.0 186.7 48.67 52.76 56.85 8.12 17.40
362.1 518580 9086.0 10037.6 237.63 257.60 277.56 2.475 5.304
HZ 1080M D 17.53 4087.8 181.4 199.9 51.49 55.57 59.66 8.12 17.41
379.8 558223 9752.6 10747.2 251.39 271.25 291.28 2.475 5.307
HZ 1180M A 18.19 4306.1 190.5 209.7 53.73 57.81 61.90 8.12 17.41
394.1 588033 10241.9 11274.1 262.33 282.25 302.22 2.475 5.307
HZ 1180M B 18.61 4497.6 199.0 218.1 55.16 59.24 63.33 8.13 17.42
403.2 614184 10698.9 11725.7 269.31 289.23 309.20 2.478 5.310
HZ 1180M C 19.42 4778.7 210.1 231.3 57.78 61.94 66.10 8.17 17.45
420.8 652571 11295.6 12435.4 282.11 302.42 322.73 2.490 5.319
HZ 1180M D 20.07 4999.8 220.4 240.3 59.99 64.14 68.30 8.19 17.47
434.9 682764 11849.4 12919.3 292.90 313.16 333.47 2.496 5.325
* Referring outside of HZ®-M-flange (v2), ** Referring outside of connector (v3), *** Length of connectors = Length of AZ.
75.87 in.
1927.1 mm
HZ 680M LT 13.21 1154.7 97.7 87.0 35.47 40.22 44.97 8.12 15.45
279.6 157685 5252.7 4677.4 173.18 196.37 219.56 2.475 4.709
HZ 880M A 14.07 2025.2 127.9 117.7 38.39 43.14 47.90 8.13 16.76
304.9 276558 6876.3 6327.9 187.44 210.63 233.87 2.478 5.108
HZ 880M B 14.84 2155.8 135.4 125.4 41.02 45.77 50.52 8.14 16.77
321.5 294392 7279.5 6741.9 200.28 223.47 246.66 2.481 5.111
HZ 880M C 15.20 2247.0 140.4 130.7 42.22 46.97 51.72 8.13 16.77
329.3 306846 7548.3 7026.8 206.13 229.33 252.52 2.478 5.111
HZ 1080M A 16.04 3679.4 178.2 167.2 45.05 49.81 54.58 8.11 18.17
347.5 502452 9580.6 8989.2 219.95 243.19 266.48 2.472 5.538
HZ 1080M B 16.59 3920.1 188.8 178.2 46.94 51.71 56.47 8.12 18.18
359.5 535322 10150.5 9580.6 229.18 252.47 275.71 2.475 5.541
HZ 1080M C 17.61 4214.2 201.8 191.6 50.40 55.16 59.92 8.12 18.18
381.6 575484 10849.4 10301.0 246.07 269.31 292.55 2.475 5.541
HZ 1080M D 18.43 4502.4 214.0 204.7 53.21 57.97 62.73 8.12 18.18
399.3 614840 11505.3 11005.3 259.79 283.03 306.27 2.475 5.541
HZ 1180M A 19.09 4718.6 222.6 214.6 55.45 60.21 64.96 8.12 18.18
413.6 644364 11967.7 11537.6 270.73 293.97 317.16 2.475 5.541
HZ 1180M B 19.48 4895.1 230.1 222.5 56.78 61.54 66.30 8.13 18.19
422.1 668466 12370.9 11962.3 277.22 300.46 323.70 2.478 5.544
HZ 1180M C 20.55 5284.8 245.9 237.5 59.92 64.92 69.92 8.17 18.30
445.3 721683 13220.3 12768.7 292.55 316.97 341.38 2.490 5.578
HZ 1180M D 21.13 5474.2 253.8 246.1 61.92 66.92 71.92 8.19 18.32
457.8 747547 13645.1 13231.1 302.32 326.73 351.14 2.496 5.584
* Referring outside of HZ®-M-flange (highest value of v1; v2), ** Referring outside of connector (highest value of v3; v4), *** Length of connectors = Length of AZ.
94.41 in.
2398.0 mm
HZ 680M LT 15.61 1450.2 114.8 103.0 46.59 49.86 53.14 9.84 16.47
330.4 198038 6172.0 5537.6 227.47 243.44 259.45 2.999 5.020
HZ 880M A 17.00 2670.3 158.9 147.0 51.29 54.57 57.86 9.84 17.77
368.3 364651 8543.0 7903.2 250.42 266.43 282.50 2.999 5.416
HZ 880M B 18.23 2880.0 171.5 159.4 55.49 58.77 62.04 9.86 17.79
395.0 393288 9220.4 8569.8 270.92 286.94 302.90 3.005 5.422
HZ 880M C 18.80 3026.7 179.8 167.9 57.43 60.70 63.98 9.86 17.78
407.3 413321 9666.6 9026.8 280.40 296.36 312.38 3.005 5.419
HZ 1080M A 20.17 5047.1 233.1 219.4 62.05 65.34 68.63 9.82 19.16
437.0 689223 12532.2 11795.6 302.95 319.02 335.08 2.993 5.840
HZ 1080M B 21.06 5435.4 250.3 236.8 65.10 68.39 71.68 9.82 19.17
456.3 742248 13456.9 12731.1 317.84 333.91 349.97 2.993 5.843
HZ 1080M C 22.68 5907.1 271.6 258.4 70.63 73.91 77.20 9.83 19.18
491.4 806663 14602.1 13892.4 344.84 360.86 376.92 2.996 5.846
HZ 1080M D 24.01 6369.8 291.6 279.3 75.13 78.41 81.69 9.84 19.18
520.2 869848 15677.3 15016.0 366.81 382.83 398.84 2.999 5.846
HZ 1180M A 25.06 6716.2 305.8 295.0 78.71 81.99 85.27 9.84 19.19
543.0 917152 16440.8 15860.1 384.29 400.31 416.32 2.999 5.849
HZ 1180M B 25.69 7000.2 318.0 307.8 80.85 84.13 87.41 9.85 19.22
556.6 955935 17096.7 16548.3 394.74 410.76 426.77 3.002 5.858
HZ 1180M C 27.08 7496.6 338.8 327.5 85.48 88.82 92.15 9.91 19.26
586.7 1023722 18214.9 17607.4 417.35 433.65 449.91 3.021 5.870
HZ 1180M D 28.01 7799.1 351.7 341.3 88.67 92.01 95.34 9.95 19.29
606.9 1065031 18908.5 18349.3 432.92 449.23 465.49 3.033 5.880
* Referring outside of HZ®-M-flange (highest value of v1; v2), ** Referring outside of connector (highest value of v3; v4), *** Length of connectors = Length of AZ.
94.41 in.
2398.0 mm
HZ 680M LT 16.41 1571.9 133.0 118.6 48.20 52.02 55.83 9.84 17.17
347.3 214657 7150.5 6376.3 235.33 253.98 272.58 2.999 5.233
HZ 880M A 17.79 2883.5 182.2 167.8 52.91 56.73 60.55 9.84 18.48
376.6 393766 9795.6 9021.4 258.33 276.98 295.63 2.999 5.633
HZ 880M B 19.02 3091.7 194.4 180.0 57.11 60.92 64.74 9.86 18.50
402.6 422197 10451.5 9677.4 278.83 297.44 316.09 3.005 5.639
HZ 880M C 19.59 3238.1 202.6 188.4 59.04 62.86 66.67 9.86 18.50
414.7 442189 10892.4 10129.0 288.26 306.91 325.51 3.005 5.639
HZ 1080M A 20.96 5405.5 262.0 245.8 63.67 67.51 71.34 9.82 19.88
443.7 738165 14085.9 13215.0 310.86 329.61 348.31 2.993 6.059
HZ 1080M B 21.86 5792.8 279.2 263.5 66.72 70.55 74.39 9.82 19.88
462.7 791054 15010.7 14166.6 325.75 344.45 363.20 2.993 6.059
HZ 1080M C 23.48 6262.5 300.1 284.9 72.25 76.07 79.90 9.83 19.89
497.0 855196 16134.3 15317.1 352.75 371.40 390.10 2.996 6.062
HZ 1080M D 24.80 6723.8 319.8 305.8 76.75 80.57 84.39 9.84 19.90
524.9 918190 17193.4 16440.8 374.72 393.37 412.03 2.999 6.066
HZ 1180M A 25.85 7069.3 333.8 321.5 80.32 84.14 87.96 9.84 19.90
547.2 965371 17946.1 17284.8 392.15 410.81 429.46 2.999 6.066
HZ 1180M B 26.48 7352.9 345.9 334.4 82.47 86.29 90.11 9.85 19.91
560.5 1004099 18596.7 17978.4 402.65 421.30 439.95 3.002 6.069
HZ 1180M C 28.07 7934.8 370.5 357.9 87.51 91.52 95.53 9.91 20.04
594.1 1083562 19919.2 19241.8 427.26 446.84 466.42 3.021 6.108
HZ 1180M D 29.01 8236.3 383.3 371.5 90.70 94.70 98.71 9.95 20.08
614.0 1124734 20607.4 19973.0 442.83 462.36 481.94 3.033 6.120
* Referring outside of HZ®-M-flange (highest value of v1; v2), ** Referring outside of connector (highest value of v3; v4), *** Length of connectors = Length of AZ.
75.87 in.
1927.1 mm
HZ 680M LT 13.73 1116.0 83.8 95.0 36.63 41.68 46.73 8.37 14.94
290.7 152 390 4 505 5 110 179 204 228 2.551 4.553
HZ 880M A 14.59 1877.8 106.7 122.1 39.55 44.61 49.67 8.37 16.23
308.9 256 420 5 735 6 565 193 218 243 2.551 4.948
HZ 880M B 15.37 2013.1 114.9 129.5 42.21 47.26 52.31 8.38 16.24
325.4 274 900 6 180 6 960 206 231 255 2.554 4.949
HZ 880M C 15.72 2105.1 120.1 134.9 43.41 48.46 53.51 8.38 16.24
332.9 287 470 6 455 7 250 212 237 261 2.554 4.949
HZ 1080M A 16.56 3361.2 149.3 167.4 46.21 51.28 56.35 8.36 17.64
350.5 458 990 8 025 9 000 226 250 275 2.547 5.378
HZ 1080M B 17.12 3608.3 160.2 178.7 48.13 53.20 58.27 8.36 17.64
362.4 492 740 8 615 9 610 235 260 285 2.548 5.378
HZ 1080M C 18.13 3905.7 173.8 192.0 51.59 56.65 61.72 8.36 17.65
383.9 533 350 9 345 10 320 252 277 301 2.549 5.379
HZ 1080M D 18.96 4196.1 186.3 205.2 54.40 59.46 64.52 8.37 17.65
401.3 573 000 10 015 11 030 266 290 315 2.550 5.380
HZ 1180M A 19.62 4414.2 195.3 215.0 56.64 61.70 66.76 8.37 17.65
415.2 602 790 10 500 11 560 277 301 326 2.551 5.381
HZ 1180M B 20.04 4605.8 203.9 223.4 58.07 63.13 68.19 8.37 17.67
424.1 628 950 10 960 12 010 284 308 333 2.552 5.385
HZ 1180M C 20.85 4886.8 214.8 236.5 60.70 65.83 70.95 8.42 17.70
441.3 667 320 11 550 12 715 296 321 346 2.565 5.394
HZ 1180M D 21.50 5107.8 225.2 245.4 62.90 68.03 73.15 8.44 17.71
455.0 697 500 12 105 13 195 307 332 357 2.571 5.399
* Referring outside of HZ®-M-flange (v2), ** Referring outside of connector (v3), *** Length of connectors = Length of AZ.
75.87 in.
1927.1 mm
HZ 680M LT 14.64 1262.7 106.8 95.2 38.38 44.10 49.83 8.37 15.69
309.9 172430 5740 5120 187 215 243 2.551 4.783
HZ 880M A 15.50 2133.5 134.7 124.1 41.30 47.03 52.76 8.37 17.00
328.2 291340 7240 6670 202 230 258 2.551 5.183
HZ 880M B 16.27 2263.9 142.2 131.7 43.93 49.65 55.37 8.38 17.01
344.4 309150 7645 7080 214 242 270 2.554 5.186
HZ 880M C 16.63 2355.1 147.2 137.0 45.13 50.86 56.58 8.38 17.01
351.9 321590 7915 7365 220 248 276 2.554 5.186
HZ 1080M A 17.47 3787.7 183.4 172.1 47.97 53.71 59.45 8.36 18.42
369.8 517240 9860 9255 234 262 290 2.547 5.613
HZ 1080M B 18.03 4028.5 194.0 183.1 49.86 55.60 61.34 8.36 18.42
381.5 550120 10430 9845 243 271 300 2.548 5.614
HZ 1080M C 19.04 4322.5 207.0 196.5 53.32 59.05 64.79 8.36 18.42
403.0 590270 11130 10565 260 288 316 2.549 5.616
HZ 1080M D 19.86 4610.6 219.2 209.6 56.13 61.86 67.59 8.37 18.43
420.4 629600 11785 11270 274 302 330 2.550 5.616
HZ 1180M A 20.52 4826.7 227.8 219.4 58.36 64.09 69.82 8.37 18.43
434.3 659120 12245 11795 285 313 341 2.551 5.617
HZ 1180M B 20.91 5003.2 235.2 227.5 59.70 65.43 71.16 8.37 18.43
442.6 683220 12645 12230 291 319 347 2.552 5.619
HZ 1180M C 21.97 5393.0 250.9 242.4 62.83 68.80 74.77 8.42 18.54
465.1 736440 13490 13030 307 336 365 2.565 5.652
HZ 1180M D 22.56 5582.2 258.8 250.9 64.84 70.80 76.77 8.44 18.56
477.5 762280 13915 13490 317 346 375 2.571 5.659
* Referring outside of HZ®-M-flange (highest value of v1; v2), ** Referring outside of connector (highest value of v3; v4), *** Length of connectors = Length of AZ.
94.41 in.
2398.0 mm
HZ 680M LT 16.75 1537.0 121.6 109.3 48.92 52.98 57.03 10.08 16.71
354.7 209 880 6 540 5 875 239 259 278 3.074 5.093
HZ 880M A 18.15 2757.2 164.1 151.9 53.63 57.70 61.76 10.09 18.01
384.1 376 510 8 825 8 165 262 282 302 3.074 5.489
HZ 880M B 19.38 2966.7 176.7 164.1 57.83 61.89 65.94 10.11 18.03
410.1 405 120 9 500 8 825 282 302 322 3.081 5.495
HZ 880M C 19.95 3113.4 185.0 172.6 59.77 63.82 67.88 10.11 18.03
422.2 425 160 9 945 9 280 292 312 331 3.080 5.495
HZ 1080M A 21.32 5134.3 237.1 223.1 64.40 68.47 72.55 10.06 19.41
451.3 701 120 12 745 11 995 314 334 354 3.066 5.915
HZ 1080M B 22.21 5522.6 254.3 240.6 67.45 71.52 75.60 10.07 19.41
470.2 754 140 13 670 12 935 329 349 369 3.068 5.918
HZ 1080M C 23.83 5994.1 275.6 262.1 72.97 77.04 81.11 10.08 19.42
504.5 818 530 14 815 14 090 356 376 396 3.072 5.921
HZ 1080M D 25.15 6456.7 295.6 283.1 77.47 81.54 85.60 10.08 19.43
532.4 881 700 15 890 15 220 378 398 418 3.073 5.922
HZ 1180M A 26.20 6803.1 309.8 298.8 81.05 85.11 89.17 10.09 19.43
554.6 929 010 16 655 16 065 396 416 435 3.074 5.923
HZ 1180M B 26.83 7087.1 321.9 311.6 83.19 87.25 91.32 10.10 19.46
568.0 967 790 17 305 16 755 406 426 446 3.077 5.932
HZ 1180M C 28.22 7583.3 342.7 331.4 87.82 91.93 96.05 10.15 19.51
597.4 1 035 550 18 425 17 815 429 449 469 3.094 5.945
HZ 1180M D 29.16 7885.8 355.6 345.0 91.01 95.12 99.23 10.19 19.54
617.2 1 076 850 19 120 18 550 444 464 484 3.107 5.955
* Referring outside of HZ®-M-flange (highest value of v1; v2), ** Referring outside of connector (highest value of v3; v4), *** Length of connectors = Length of AZ.
94.41 in.
2398.0 mm
HZ 680M LT 17.55 1658.6 140.3 125.2 50.54 55.13 59.73 10.08 17.41
371.5 226 490 7 545 6 730 247 269 292 3.074 5.307
HZ 880M A 18.94 2970.4 187.7 172.9 55.25 59.85 64.46 10.09 18.72
400.9 405 620 10 090 9 295 270 292 315 3.074 5.706
HZ 880M B 20.17 3178.5 199.9 185.0 59.45 64.04 68.63 10.11 18.74
426.9 434 040 10 745 9 945 290 313 335 3.081 5.713
HZ 880M C 20.74 3324.8 208.0 193.4 61.38 65.97 70.57 10.11 18.74
438.9 454 020 11 185 10 400 300 322 345 3.080 5.712
HZ 1080M A 22.11 5492.6 266.2 249.8 66.02 70.64 75.26 10.06 20.12
468.1 750 050 14 310 13 430 322 345 367 3.066 6.132
HZ 1080M B 23.01 5879.9 283.4 267.4 69.07 73.69 78.30 10.07 20.13
487.0 802 940 15 235 14 375 337 360 382 3.068 6.135
HZ 1080M C 24.63 6349.5 304.3 288.8 74.59 79.20 83.81 10.08 20.14
521.3 867 060 16 360 15 525 364 387 409 3.072 6.138
HZ 1080M D 25.95 6810.8 323.9 309.8 79.09 83.70 88.30 10.08 20.14
549.2 930 050 17 415 16 655 386 409 431 3.073 6.139
HZ 1180M A 26.99 7156.2 337.9 325.5 82.67 87.27 91.87 10.09 20.15
571.4 977 220 18 165 17 500 404 426 449 3.074 6.140
HZ 1180M B 27.63 7439.8 350.0 338.4 84.81 89.41 94.01 10.10 20.16
584.7 1 015 950 18 815 18 195 414 437 459 3.077 6.144
HZ 1180M C 29.22 8021.5 374.6 361.8 89.84 94.63 99.42 10.15 20.28
618.4 1 095 390 20 140 19 450 439 462 485 3.094 6.181
HZ 1180M D 30.15 8323.0 387.3 375.4 93.03 97.82 102.61 10.19 20.32
638.2 1 136 560 20 825 20 185 454 478 501 3.107 6.194
* Referring outside of HZ®-M-flange (highest value of v1; v2), ** Referring outside of connector (highest value of v3; v4), *** Length of connectors = Length of AZ.
Combination C 1
D = discontinuous weld, a = 0.236" (6 mm), 10% of length (3.94" per 3.28', 100 mm/m) over the whole pile length + 19.68" (500 mm) continuous weld at top and toe
HZ 680M LT 18.70 11.08 12.54 12.50 - 27.69 94.28 3014.1 240.4 241.1 1.81 8.52
47.5 281.4 318.4 317.6 586.4 460.3 411590 12 925 12960 0.552 2.594
HZ 880M A 18.70 14.96 16.67 16.31 – 31.28 106.46 5939.0 356.2 364.1 1.81 9.85
47.5 379.9 423.5 414.3 662.1 519.8 811 010 19 150 19 575 0.551 3.001
HZ 880M B 18.70 15.13 16.66 16.41 – 34.37 116.98 6464.9 388.1 394.0 1.82 9.85
47.5 384.3 423.1 416.7 727.6 571.1 882 820 20 865 21 185 0.554 3.003
HZ 880M C 18.70 15.24 16.71 16.44 – 35.81 121.88 6836.8 409.2 415.9 1.82 9.85
47.5 387.1 424.3 417.5 758.1 595.1 933 600 22 000 22 360 0.554 3.002
HZ 1080M A 18.50 19.72 21.52 21.08 – 39.49 134.40 11736.7 545.5 556.9 1.79 11.26
47.0 500.9 546.5 535.3 835.9 656.2 1 602 720 29 330 29 940 0.547 3.431
HZ 1080M B 18.50 19.91 21.57 21.14 – 41.82 142.31 12745.5 591.0 602.8 1.80 11.26
47.0 505.6 547.8 537.1 885.1 694.8 1 740 470 31 775 32 410 0.548 3.431
HZ 1080M C 18.50 20.10 21.61 21.22 – 45.86 156.08 13915.7 644.0 655.7 1.80 11.26
47.0 510.6 548.8 539.0 970.7 762.0 1 900 270 34 625 35 255 0.549 3.433
HZ 1080M D 18.50 20.31 21.71 21.27 – 49.17 167.35 15075.7 694.3 708.7 1.80 11.26
47.0 515.9 551.5 540.3 1 040.9 817.1 2 058 680 37 330 38 100 0.550 3.433
HZ 1180M A 18.70 20.51 21.83 21.31 – 51.79 176.26 15938.9 730.1 747.9 1.81 11.27
47.5 520.9 554.5 541.3 1 096.3 860.6 2 176 560 39 250 40 210 0.551 3.434
HZ 1180M B 18.70 20.65 21.84 21.38 – 53.51 182.11 16715.1 765.2 781.9 1.82 11.29
47.5 524.5 554.9 543.0 1 132.6 889.1 2 282 550 41 140 42 040 0.553 3.440
HZ 1180M C 18.70 20.58 22.07 21.34 – 56.58 192.56 17798.2 806.4 833.9 1.83 11.34
47.5 522.8 560.6 542.1 1 197.6 940.1 2 430 450 43 355 44 835 0.558 3.457
HZ 1180M D 18.70 20.78 22.03 21.46 – 59.12 201.21 18656.7 846.9 869.3 1.85 11.37
47.5 527.9 559.5 545.2 1 251.5 982.4 2 547 690 45 530 46 735 0.564 3.464
Form a Form b
Combination C 23
D = discontinuous weld, a = 0.236" (6 mm), 10% of length (3.94" per 3.28', 100 mm/m) over the whole pile length + 19.68" (500 mm) continuous weld at top and toe
R = continuous weld, a = 0.236" (6 mm), length 19.68" (500 mm) at top and toe only
37.40 11.39 12.23 12.81 13.67 28.38 96.63 3121.2 255.2 228.4 3.53 10.24
HZ 680M LT 95.0 289.2 310.7 325.4 347.1 601.0 471.8 426220 13 720 12 280 1.075 3.117
37.40 15.31 16.32 16.67 17.67 31.97 108.81 6126.0 375.4 346.6 3.53 11.62
HZ 880M A 95.0 389.0 414.4 423.4 448.9 676.7 531.2 836 540 20 185 18 635 1.074 3.542
37.40 15.44 16.35 16.72 17.63 35.03 119.21 6641.1 406.2 376.7 3.55 11.64
HZ 880M B 95.0 392.1 415.3 424.6 447.7 741.5 582.0 906 880 21 840 20 255 1.081 3.549
37.40 15.54 16.41 16.73 17.61 36.47 124.12 7012.4 427.3 398.2 3.54 11.64
HZ 880M C 95.0 394.6 416.8 425.1 447.3 772.0 606.0 957 590 22 975 21 410 1.080 3.548
37.00 20.09 21.14 21.45 22.50 40.19 136.79 12054.7 570.2 535.9 3.50 13.02
HZ 1080M A 94.0 510.4 537.0 544.8 571.4 850.8 667.9 16 461 40 30 655 28 810 1.066 3.969
37.00 20.24 21.23 21.48 22.47 42.48 144.57 13045.2 614.5 580.6 3.51 13.03
HZ 1080M B 94.0 514.1 539.3 545.5 570.7 899.2 705.9 17 814 00 33 035 31 215 1.068 3.971
37.00 20.40 21.30 21.52 22.42 46.52 158.33 14212.4 667.1 633.8 3.52 13.04
HZ 1080M C 94.0 518.3 541.1 546.7 569.6 984.8 773.0 19 407 90 35 865 34 075 1.072 3.974
37.00 20.59 21.43 21.55 22.39 49.84 169.60 15370.6 717.2 686.4 3.52 13.04
HZ 1080M D 94.0 523.1 544.3 547.5 568.8 1054.9 828.1 20 989 50 38 560 36 905 1.073 3.975
37.40 20.77 21.57 21.58 22.37 52.45 178.50 16231.2 752.6 725.6 3.52 13.05
HZ 1180M A 95.0 527.6 547.8 548.0 568.2 1 110.2 871.5 22 164 70 40 460 39 010 1.074 3.977
37.40 20.86 21.63 21.59 22.36 54.05 183.95 16952.4 783.6 758.2 3.54 13.08
HZ 1180M B 95.0 529.9 549.5 548.3 567.9 1 144.1 898.1 23 149 50 42 130 40 765 1.078 3.988
37.40 20.87 21.78 21.64 22.54 57.37 195.26 18147.9 833.3 805.2 3.57 13.15
HZ 1180M C 95.0 530.2 553.2 549.5 572.5 1 214.4 953.3 24 782 00 44 800 43 290 1.087 4.009
37.40 20.97 21.84 21.65 22.52 59.68 203.09 18888.9 864.9 838.8 3.61 13.18
HZ 1180M D 95.0 532.7 554.7 550.0 572.0 1 263.2 991.6 25 794 00 46 500 45 095 1.099 4.018
Mass ± 2.5% ± 5%
Length + 5 inches – 0 inches ± 200 mm
Height ± 5 mm
Width ± 2%
Width Interlocked ± 3%
Straightness 0.2% of the length
Ends out of Square ± 2% of the width
AZ Pile
Thickness ≤ 8.5 mm ± 0.5 mm
> 8.5 mm ± 6%
HZ -M Pile
®
H-Piles
Recycled Content: 100%
Recyclable: 100%
H-pile (also referred to as HBP or HP) is manufactured by Nucor and constitutes most of the steel pile supplied by
Skyline Steel. For the first time in several decades, Nucor recently expanded the H-pile range. Traditionally, H-pile was made
in 8-, 10-, 12-, and 14-inch sizes. The capacity of previous sections has been nearly doubled through the addition of new
ranges of 16- and 18-inch pile. Like all other steel produced using the electric arc furnace, H-pile is made from 100% scrap
and is 100% recyclable.
Applications of H-Pile
H-piles are commonly used as bearing piles and are driven into the ground to support bridges, buildings, factories, stadiums,
and nearly every other type of structure. H-piles are most effective as end-bearing piles, but also resist load through skin
friction. H-piles are also used for walers and bracing in cofferdams and in beam and lagging walls.
H-Pile
Grand Rapids, MI
Wichita, KS Orlando, FL
HP
Steel H-Pile
THICKNESS PROPERTIES
Flange Coating AXIS X-X AXIS Y-Y
Weight Area Depth Width Flange Web Area
d b (tf) (tw) I S Z r I S Z r
lb/ft in2 in in in in ft2/ft in4 in3 in3 in in4 in3 in3 in
SECTION (kg/m) (cm2) (mm) (mm) (mm) (mm) (m2/m) (cm4) (cm3) (cm3) (cm) (cm4) (cm3) (cm3) (cm)
HP 8 36 10.6 8.02 8.16 0.445 0.445 3.92 119 29.8 33.6 3.36 40.3 9.88 15.2 1.95
HP 200 54 68.4 204 207 11.3 11.3 1.19 4953 488 550.6 8.53 1677 162 249.1 4.95
42 12.4 9.70 10.10 0.420 0.415 4.83 210 43.4 48.3 4.13 71.7 14.2 21.8 2.41
HP 10 63 80.0 246 257 10.7 10.5 1.47 8741 711 791.5 10.5 2984 233 357.2 6.12
HP 250 57 16.7 9.99 10.20 0.565 0.565 4.91 294 58.8 66.5 4.18 101 19.7 30.3 2.45
85 108 254 259 14.4 14.4 1.50 12237 964 1089.7 10.6 4204 323 496.5 6.22
53 15.5 11.80 12.00 0.435 0.435 5.82 393 66.7 74.0 5.03 127 21.1 32.2 2.86
79 100 300 305 11.0 11.0 1.77 16358 1093 1212.6 12.8 5286 346 527.7 7.26
63 18.4 11.90 12.10 0.515 0.515 5.86 472 79.1 88.3 5.06 153 25.3 38.7 2.88
94 119 302 307 13.1 13.1 1.79 19646 1296 1447.0 12.9 6368 415 634.2 7.32
74 21.8 12.10 12.20 0.610 0.605 5.91 569 93.8 105 5.11 186 30.4 46.6 2.92
110 141 307 310 15.5 15.4 1.80 23683 1537 1720.6 13.0 7742 498 763.6 7.42
HP 12 84 24.6 12.30 12.30 0.685 0.685 5.97 650 106 120 5.14 213 34.6 53.2 2.94
HP 310 125 159 312 312 17.4 17.4 1.82 27055 1737 1966.4 13.1 8866 567 871.8 7.47
89 25.9 12.36 12.32 0.720 0.720 6.04 689 111.6 126.3 5.16 225 36.5 56.2 2.94
132 167 314 313 18.3 18.3 1.84 28700 1830 2070 13.1 9370 599 922 7.48
102 29.9 12.56 12.64 0.819 0.819 6.17 811 129.3 147.6 5.20 276 43.7 67.1 3.04
152 193 319 321 20.8 20.8 1.88 33800 2120 2420 13.2 11500 716 1100 7.71
117 34.4 12.76 12.87 0.929 0.929 6.26 946 148.2 170.8 5.24 331 51.4 79.3 3.11
174 222 324 327 23.6 23.6 1.91 39400 2430 2800 13.3 13800 843 1300 7.89
73 21.4 13.60 14.60 0.505 0.505 6.96 729 107 118 5.84 261 35.8 54.6 3.49
109 138 345 371 12.8 12.8 2.12 30343 1753 1933.7 14.8 10864 587 894.7 8.86
89 26.1 13.80 14.70 0.615 0.615 7.02 904 131 146 5.88 326 44.3 67.7 3.53
HP 14 132 168 351 373 15.6 15.6 2.14 37627 2147 2392.5 14.9 13569 726 1109.4 8.97
HP 360 102 30.1 14.00 14.80 0.705 0.705 7.06 1050 150 169 5.92 380 51.4 78.8 3.56
152 194 356 376 17.9 17.9 2.15 43704 2458 2769.4 15.0 15817 842 1291.3 9.04
117 34.4 14.20 14.90 0.805 0.805 7.12 1220 172 194 5.96 443 59.5 91.4 3.59
174 222 361 378 20.4 20.4 2.34 50780 2819 3179.1 15.1 18439 975 1497.8 9.12
88 25.8 15.30 15.70 0.540 0.540 7.52 1110 145 161 6.56 349 44.5 68.2 3.68
131 167 389 399 13.7 13.7 2.29 46201 2376 2638.3 16.7 14526 729 1117.6 9.35
101 29.9 15.50 15.80 0.625 0.625 7.56 1300 168 187 6.59 412 52.2 80.1 3.71
150 193 394 401 15.9 15.9 2.30 54110 2753 3064.4 16.7 17149 855 1312.6 9.42
121 35.8 15.80 15.90 0.750 0.750 7.62 1590 201 226 6.66 504 63.4 97.6 3.75
HP 16 180 231 401 404 19.1 19.1 2.32 66180 3294 3703.5 16.9 20978 1039 1599.4 9.53
HP 410 141 41.7 16.00 16.00 0.875 0.875 7.69 1870 234 264 6.70 599 74.9 116 3.79
210 269 406 406 22.2 22.2 2.34 77835 3835 4326.2 17.0 24932 1227 1900.9 9.63
162 47.7 16.30 16.10 1.000 1.000 7.75 2190 269 306 6.78 697 86.6 134 3.82
241 308 414 409 25.4 25.4 2.36 91154 4408 5014.4 17.2 29011 1419 2195.9 9.70
183 54.1 16.50 16.30 1.130 1.130 7.81 2510 304 349 6.81 818 100.0 156 3.89
272 349 419 414 28.7 28.7 2.38 104473 4982 5719.1 17.3 34047 1639 2556.4 9.88
135 39.9 17.50 17.80 0.750 0.750 8.54 2200 251 281 7.43 706 79.3 122 4.21
201 257 445 452 19.1 19.1 2.60 91570 4113 4604.7 18.9 29386 1299 1999.2 10.7
157 46.2 17.70 17.90 0.870 0.870 8.60 2570 290 327 7.46 833 93.1 143 4.25
HP 18 234 298 450 455 22.1 22.1 2.62 106971 4752 5358.5 18.9 34672 1526 2343.3 10.8
HP 460 181 53.2 18.00 18.00 1.000 1.000 8.66 3020 336 379 7.53 974 108.0 167 4.28
269 343 457 457 25.4 25.4 2.64 125701 5506 6210.7 19.1 40541 1770 2736.6 10.9
204 60.2 18.30 18.10 1.130 1.130 8.73 3480 380 433 7.60 1120 124.0 191 4.31
304 388 465 460 28.7 28.7 2.66 144847 6227 7095.6 19.3 46618 2032 3129.9 11.0
Mass ± 2.5%
Length §
†
Longer lengths may be possible upon request.
Skyline Steel manufactures three types of pipe: Straight seam (ERW), spiralweld and rolled & welded. They are all made
from steel that has similar physical and chemical properties. All of these types of pipe are welded with full penetration
welds that are just as strong as the base material.
ERW Pipe
Pipe
ERW pipe is made from steel coil and the weld seam runs parallel to the pipe. The width of the coil is the same as the
circumference of the pipe so diameters are limited to 24 inches. However, the manufacturing process is fast so it is ideal for
large production runs of small (<= 24 in.) diameter sections.
Spiralweld Pipe
Spiralweld pipe, like ERW, is also manufactured from steel coil. The difference is the coil is wound at an angle, so the weld
runs around the outside of the pipe in the shape of a helix. This allows for a lot more variation in diameter and thickness
than ERW pipe. Spiralweld pipe is most commonly used for pipe diameters between 24 in. and 120 in. and for thicknesses of
1.0 in. or less.
Pipe is ideal for bearing piles since it can be produced in a wide variety of sizes, grades, and lengths. It is also easy to splice
and can be driven open or closed-ended. Closed-ended pipe can be filled with concrete to increase the total capacity after
the pile has been driven. The American Society of Civil Engineers (ASCE) recommends a lower safety factor for concrete-
filled, closed-ended pipe than any other type of foundation pile (driven or drilled), primarily due to the predictability of a
quality installed product. Pipe can also be used for:
Seattle, WA
DO
APPROXIMATE VALUES
DI Pipe Weight (lbs/ft) = 10.69*t*(DO-t)
t DO (in) - outside diameter
t (in) - thickness of pipe
Pipe Weight (kg/m) = 0.0247*t*(DO-t)
DO (mm) - outside diameter
t (mm) - thickness of pipe
24 47.86 51.64 55.67 63.47 79.01 94.71 125.61 156.17 186.41 245.87
609.6 71.22 76.85 82.85 94.46 117.57 140.94 186.92 232.41 277.40 365.94
Easy Weight Calculator (All Dimensions in inches. Density of steel = 0.2836 lbs/in3)
DI
π π
Weight (lbs) = A x B x Thickness x 0.2836 Weight (lbs) = Thickness x (DO2 - DI2) x 0.2836 Weight (lbs) = Thickness x (D2) x 0.2836
4 4
π π 2
Area = (DO2 - DI2) Area = D
4 4
DO
APPROXIMATE VALUES
Additional Capabilities
Installation of:
Bands, Cutting Shoes, End Plates, Carbide Teeth, Rolled Channel and Angle Iron, Twisting Slots, Picking Eyes,
Lifting Lugs, etc.
Pipe manufactured to American Welding Society standards. Structural welding code AWS D1.1 or D1.5 is also available.
Outside Diameter ± 1%
Weight/Thickness Per Specification
Length ± 1 inch
DO
APPROXIMATE VALUES
DI Pipe Weight (lbs/ft) = 10.69*t*(DO-t)
t DO (in) - outside diameter
t (in) - thickness of pipe
Pipe Weight (kg/m) = 0.0247*t*(DO-t)
DO (mm) - outside diameter
t (mm) - thickness of pipe
10 3/4 20.23 21.23 22.89 24.65 28.06 34.81 40.52 (0.365) 54.79
273.05 30.10 31.59 34.06 36.69 41.76 51.81 60.30 81.54
Easy Weight Calculator (All Dimensions in inches. Density of steel = 0.2836 lbs/in3)
DI
π π
Weight (lbs) = A x B x Thickness x 0.2836 Weight (lbs) = Thickness x (DO2 - DI2) x 0.2836 Weight (lbs) = Thickness x (D2) x 0.2836
4 4
π π 2
Area = (DO2 - DI2) Area = D
4 4
Structural Sections
Recycled Content: 100%
Recyclable: 100%
Skyline Steel takes great pride in providing a wide range of structural sections from several different mills. All sections
(including jumbo beams and columns) found in the American Institute of Steel Construction (AISC) manual are available.
Beams
Available Steel Grades
AMERICAN CANADIAN EUROPEAN*
Mass ± 2.5%
Depth ± 0.125 inches
Length 30 feet and under Over 30 Feet
Beams W 24 and Under ± 0.375 inches + ( 0.375 inches + (Length - 30) / 80 -0.375 inches
Beams Over W 24 ± 0.5 inches + ( 0.5 inches + (Length - 30) / 80 -0.375 inches
Flanges out of Square
Beams W 12 and Under ≤ 0.25 inches
Beams Over W 12 ≤ 0.3125 inches
Web off Center ≤ 0.1875 inches
Greatest Depth over Theoretical ≤ 0.25 inches
Camber and Sweep (0.125 in) * (Length / 10)
Camber and Sweep for Columns*
45 Feet and Under (0.125 in) * (Length / 10) but not over 0.375 inches
Over 45 Feet (0.375 in) + (0.125 in * (Length - 45) / 10
*W 8 x 31 and heavier, W 10 x 49 and heavier, W 12 x 65 and heavier, and W 14 x 90 and heavier order as columns.
If other sections are ordered as columns, the tolerances are subject to negotiation with manufacturer.
Channels Angles
Available Steel Grades Available Steel Grades
AMERICAN AMERICAN
CANADIAN CANADIAN
YIELD STRENGTH YIELD STRENGTH
CSA G40.21 CSA G40.21
(ksi) (MPa) (ksi) (MPa)
Grade 350 W 50 350 Grade 350 W 50 350
EUROPEAN EUROPEAN
YIELD STRENGTH YIELD STRENGTH
EN 10248 EN 10248
(ksi) (MPa) (ksi) (MPa)
S 235 GP 34 235 S 235 34 235
S 355 GP 51 355 S 355 51 355
Pile Accessories
Recycled Content: 100%
Recyclable: 100%
Since geotechnical exploration and pile driving are not exact sciences, it is often challenging to predict the difficulty of
driving piles and also to determine what their final lengths will be. To assist engineers and contractors in the construction of
deep foundations, pile splicers, shoes, points, and other accessories are available.
HP Accessories
HP Splicer
HP Point
HP Point
HP Point
Pipe Accessories
Backing Ring
Timber Accessories
Contact Information
Associated Pile & Fitting
Tel: (973) 773-8400
Toll Free: (800) 526-9047
Fax: (973) 773-8442
apf@associatedpile.com
www.associatedpile.com
As a leader in the sheet pile industry, we are proud to introduce our new line of High Density Polyethylene (HDPE)
sheet piles, the PE30. HDPE is impermeable and exceptionally resistant to corrosion, biological attacks, chemicals, and
salts making it ideal for cutoff walls. By nearly eliminating deterioration, HDPE is unmatched when compared to other Environ
subsurface materials, thus allowing for an extremely long design life and minimizing the risk of premature failure.
Incorporating the benefits of HDPE, the PE30 can be used in a full range of environments including marine, industrial,
manufacturing, and mining.
The PE30’s revolutionary design combines the time tested benefits of HDPE with the latest innovations in sheet pile
technology. The PE30 is equipped with the Larssen Interlock which is the least permeable system available in today’s
market. In addition, the effective permeability of the joints can be further decreased by using sealants. The PE30 is
domestic, readily available and cost-effective, making it an ideal solution for environmental barrier applications.
Environ
Environ PE30
Environ PE30 Sheet Pile
MATERIAL PROPERTIES
Thickness
Width Height Section Moment
(w) (h) Flange Web Weight Modulus of Inertia
(tf) (tw)
in in in in lb/ft in3/ft in4/ft
Density
Peak Tensile Stress Modulus of Elasticity Hardness (HDPE Compound)
Test Method ASTM D3039/D638 ASTM D3039/D638 ASTM 2240 ISO 1183
As a premier supplier of steel foundation products, Skyline Steel offers a comprehensive line of geostructural products.
Since becoming a member of the Nucor family, a concentrated emphasis has been made to fully develop the geostructural
business unit into a leader in the supply side of the heavy civil construction business.
A core group of geostructural industry specialists has been assembled to focus on providing superior service to this growing
market niche. A significant investment in manufacturing has been made which has allowed us to add new product lines
and strengthen our existing product offering. In addition to Skyline Steel’s complete line of grade 75 and grade 150 cold
rolled threaded bar, we now offer an improved hot-rolled fully threaded bar. Our manufacturing capabilities have also
been expanded to allow us to produce DCP shop grouted and SCP ground anchors in multiple locations across the United
States. Skyline Steel’s experienced production team has become experts at assembling large-scale reinforcement bar cages
measuring over 109 feet long, using couplers and full load nuts.
Significant improvements have also been made in our micropile manufacturing capabilities. Micropile threaded casing
production capacity has been expanded to further supplement our full line of bar reinforcing products, making us the single
source supplier to any contractor involved in a micropile project. Multi-strand anchors, featuring Samwoo load distributive
anchor systems with removable capabilities, are now available from Skyline Steel. A comprehensive hollow bar system with
Geostructural
a full line of complementary accessories has also been added to our geostructural product offering. Skyline Steel is pleased
Solutions
to be a market leader in the specialty products described in this manual and we are dedicated to partnering with our
customers and delivering high quality products and cost effective solutions.
Chicago, IL
Cold rolled threaded bars conform to the physical and chemical requirements of ASTM A 615 Grade 75 ksi “Standard Specification for Deformed Carbon Steel Bars for Concrete Reinforcement”
* Contact your local Skyline Steel representative for information on additional steel grades.
Approx. Major
Thread Diameter
Threaded Bar Connectors Full Load Hex Nuts and Jam Nuts
OD
A B A C
L
Full Load Hex Nut Jam Nut
Weight
OD L Weight A B C
Bar Bar lbs
Designation in in lbs Designation in in in (kg)
(mm) (mm) (kg) (mm) (mm) (mm)
Full Jam
1.625 4.500 1.55 1.625 2.000 0.500 0.81 0.20
#8 #8 0.09
41.3 114.3 0.70 41.3 50.8 12.7 0.37
1.875 5.000 2.39 1.750 2.000 0.563 0.89 0.25
#9 #9 0.11
47.6 127.0 1.08 44.5 50.8 14.3 0.40
2.125 5.500 3.47 2.000 2.187 0.625 1.33 0.38
#10 #10 0.17
54.0 139.7 1.57 50.8 55.5 15.9 0.60
2.250 6.000 4.02 2.250 2.500 0.688 1.96 0.54
#11 #11 0.24
57.2 152.4 1.82 57.2 63.5 17.5 0.89
2.875 7.875 9.16 2.750 3.250 0.938 3.86 1.11
#14 #14 0.50
73.0 200.0 4.15 69.9 82.6 23.8 1.75
3.500 9.125 13.93 4.000 4.500 1.000 4.87 1.81
#18 #18 0.82
88.9 231.8 6.32 101.6 114.3 25.4 2.21
4.000 9.500 19.86 4.000 4.500 1.125 9.83 2.76
#20 #20* 1.25
101.6 241.3 9.01 101.6 114.3 28.6 4.46
4.750 10.750 31.01 4.750 4.500 1.500 12.98 4.33
#24 #24** 1.96
120.6 243.0 14.07 120.6 114.3 38.1 5.89
5.500 12.000 46.20 5.500 6.000 1.563 23.10 6.02
#28 #28** 2.73
139.7 304.8 20.96 139.7 152.4 39.7 10.48
*Round collar nut available **Round collar nut with flats
Please note: As we continuously improve the design of our products, product details are subject to change.
† Contact your sales representative for information on hot dip galvanized and epoxy coated hardware (available upon request).
Nominal Nominal
A B C Weight A B C D Bevel Weight
Diameter Diameter
in in in in lbs in in in in degrees lbs
in
(mm) (mm) (mm) (mm) (kg) (mm) (mm) (mm) (mm) (kg)
(mm)
Please note: As we continuously improve the design of our products, product details are subject to change.
Contact your local Skyline Steel representative for information on additional steel grades.
C
B
A
SECTION A SECTION B
Bearing plate dimensions reflect typical sizes. SECTION A
Actual design criteria should be used for specific plate sizing.
A B C
A B C Weight Bar
Bar Designation in in in
Designation in in in lbs (mm) (mm) (mm)
(mm) (mm) (mm) (kg)
#8 – #11 3.5 2.25 6.75
88.9 57.2 171.5
#8 8 8 3/4 13.40
203.20 203.20 19.05 6.08 #14 – #28 6.5 4.25 10.25
165.1 108.0 260.4
#9 8 8 3/4 13.35
203.20 203.20 19.05 6.06
Nominal
A B C Weight L
Diameter
in in in lbs
in
(mm) (mm) (mm) (kg) Grade 150 Anchor Nuts
(mm)
Please note: As we continuously improve the design of our products, product details are subject to change.
C Threaded
Portion
Threaded
Portion
A B C D E F
Bar
Designation in in in in in in
(mm) (mm) (mm) (mm) (mm) (mm)
Contact your Skyline Steel sales representative for assistance with connection details. Single Corrosion Protection (SCP)
Approx. Major
Thread Diameter
Nominal Min. Net Area Min. Ultimate Min. Yield Nominal Approx. Major Max.
Bar Thread
Grade Diameter Thru Threads Strength Strength Weight Thread Diameter Length
Designation Orientation
in in2 kips kips lbs/ft in ft
(mm) (mm2) (kN) (kN) (kg/m) (mm) (m)
Hot rolled threaded bars conform (Excluding the requirement of: “legibly rolled surface markings.”) to the requirements of ASTM A 615 Grade 75 ksi (520 Mpa) “Standard Specification for
Deformed Carbon Steel Bars for Concrete Reinforcement”
† Contact your sales representative for information on hot dip galvanized and epoxy coated bars.
Please note: As we continuously improve the design of our products, product details are subject to change.
#6 3/4 1.25 3.125 0.62 3/4 1.125 1.45 0.87 0.26 0.16
20 31.75 79.37 0.28 #6 20 28.57 36.83 22.10 0.12 0.07
#7 7/8 1.50 3.75 0.93 7/8 1.375 1.75 0.87 0.43 0.21
22 38.10 95.25 0.42 #7 22 34.92 44.45 22.10 0.20 0.10
#9 1-1/8 1.875 5.00 2.31 1-1/8 1.75 2.25 0.87 0.97 0.37
28 47.62 127.00 1.05 #9 28 44.45 57.15 22.10 0.43 0.17
#10 1-1/4 2.00 5.75 2.77 1-1/4 2.00 2.50 1.00 1.43 0.56
32 50.80 146.05 1.26 #10 32 50.80 63.50 25.40 0.65 0.25
#11 1-3/8 2.25 6.40 3.79 1-3/8 2.25 2.75 1.00 1.52 0.53
35 57.15 162.56 1.72 #11 35 57.15 69.85 25.40 0.69 0.24
#14 1-3/4 2.88 7.85 5.49 1-3/4 2.50 3.60 1.00 3.02 0.82
45 73.15 192.53 2.49 #14 45 63.50 91.44 25.40 1.37 0.37
B B
D
Nominal Nominal
Bar Diameter A B C Weight Bar Diameter A B C D Bevel Weight
Designation Designation degrees
in in in in lbs in in in in in lbs
(mm) (mm) (mm) (mm) (kg) (mm) (mm) (mm) (mm) (mm) (kg)
#6 3/4 1.75 0.938 .136 0.07 3/4 1.75 .95 .78 .32 .32
20 44.45 23.83 3.45 0.03 #6 20 44.45 24.13 19.81 8.13
15 0.15
#7 7/8 2.00 1.063 .136 0.09 7/8 1.75 1.14 .78 .32 .37
22 50.80 27.00 3.45 0.04 #7 22 44.45 28.96 19.81 8.13
15 0.17
#9 1-1/8 2.50 1.375 .136 0.13 1-1/8 2.63 1.38 .93 .23 .64
28 63.50 34.92 3.45 0.06 #9 28 66.80 31.75 23.62 5.84
15 0.29
#10 1-1/4 2.75 1.531 .136 0.16 1-1/4 2.75 1.63 .97 .23 .66
32 69.85 38.89 3.45 0.07 #10 32 69.85 41.40 24.64 5.84
15 0.30
#11 1-3/8 3.00 1.625 .136 0.19 1-3/8 3.09 1.75 1.06 .23 .93
35 76.20 41.27 3.45 0.09 #11 35 78.49 44.45 26.92 5.84
15 0.45
#14 1-3/4 3.25 1.77 .178 0.30 1-3/4 4.00 2.13 1.29 .23 1.94
45 82.55 44.96 4.52 0.14 #14 45 10.16 54.10 32.77 5.84
15 0.88
Please note: As we continuously improve the design of our products, product details are subject to change.
Thread Shaft
Thread Shaft Recommended
Diameter Diameter Tensile Yield Ultimate Gross Yield Ultimate Design Capacity
Stress Area Capacity Capacity Area Capacity Capacity
Bar
DT Dg As Thy Thu Ag Shy Shu ASD* LRFD*
in in in2 kips kips in2 kips kips kips kips
mm mm mm2 kN kN mm2 kN kN kN kN
M 85/64 3.3 2.52 7.67 556 734 4.99 362 477 217 344
85 64 4,948 2,474 3,266 3,217 1,608 2,123 963 1,528
M 90/68 3.5 2.68 8.67 628 830 5.63 408 539 244 388
90 68 5,591 2,795 3,690 3,632 1,816 2,397 1,087 1,725
M 95/72 3.7 2.83 9.72 705 931 6.31 458 604 274 435
95 72 6,273 3,137 4,140 4,072 2,036 2,687 1,219 1,934
M 100/76 3.9 2.99 10.84 786 1,038 7.03 510 673 305 484
100 76 6,995 3,497 4,616 4,536 2,268 2,994 1,358 2,155
M 105/80 4.1 3.15 12.02 872 1,151 7.79 565 746 338 537
105 80 7,755 3,878 5,119 5,027 2,513 3,318 1,505 2,388
M 110/85 4.3 3.35 13.26 962 1,269 8.80 638 842 381 606
110 85 8,556 4,278 5,647 5,675 2,837 3,745 1,694 2,695
M 115/90 4.5 3.54 14.56 1,056 1,394 9.86 715 944 418 669
115 90 9,395 4,697 6,201 6,362 3,181 4,199 1,860 2,976
M 120/90 4.7 3.54 15.92 1,155 1,524 9.86 715 944 428 679
120 90 10,274 5,137 6,781 6,362 3,181 4,199 1,905 3,022
M 125/95 4.9 3.74 17.35 1,258 1,661 10.99 797 1,052 477 757
125 95 11,191 5,596 7,386 7,088 3,544 4,678 2,122 3,367
M 130/100 5.1 3.94 18.83 1,366 1,803 12.17 883 1,165 529 839
130 100 12,149 6,074 8,018 7,854 3,927 5,184 2,351 3,731
M 135/105 5.3 4.13 20.37 1,478 1,950 13.42 973 1,285 583 925
135 105 13,145 6,573 8,676 8,659 4,330 5,715 2,593 4,113
M 140/110 5.5 4.33 21.98 1,594 2,104 14.73 1,068 1,410 631 1,010
140 110 14,181 7,090 9,359 9,503 4,752 6,272 2,808 4,492
M 145/110 5.7 4.33 23.65 1,715 2,264 14.73 1,068 1,410 640 1,015
145 110 15,256 7,628 10,069 9,503 4,752 6,272 2,845 4,514
M 150/115 5.9 4.53 25.37 1,840 2,429 16.10 1,168 1,541 699 1,109
150 115 16,370 8,185 10,804 10,387 5,193 6,855 3,110 4,934
M 155/120 6.1 4.72 27.16 1,970 2,600 17.53 1,271 1,678 761 1,208
155 120 17,524 8,762 11,566 11,310 5,655 7,464 3,386 5,372
M 160/125 6.3 4.92 29.01 2,104 2,777 19.02 1,379 1,821 826 1,310
160 125 18,716 9,358 12,353 12,272 6,136 8,099 3,674 5,829
M 165/130 6.5 5.12 30.92 2,242 2,960 20.57 1,492 1,969 888 1,417
165 130 19,948 9,974 13,166 13,273 6,637 8,760 3,950 6,305
The recommended design capacities are based on AISC/ASD and AASHTO/LRFD design methodologies for steel structures and retaining walls. Additional reduction factors from EN1993-5 are
applied to the tie rods based on their ability to articulate.
Thread Shaft
Thread Shaft Recommended
Diameter Diameter Tensile Yield Ultimate Gross Yield Ultimate Design Capacity
Stress Area Capacity Capacity Area Capacity Capacity
Bar
DT Dg As Thy Thu Ag Shy Shu ASD* LRFD*
in in in2 kips kips in2 kips kips kips kips
mm mm mm2 kN kN mm2 kN kN kN kN
M 85/76 3.3 2.99 7.67 556 734 7.03 510 673 305 484
85 76 4,948 2,474 3,266 4,536 2,268 2,994 1,358 2,155
M 90/80 3.5 3.15 8.67 628 830 7.79 565 746 338 537
90 80 5,591 2,795 3,690 5,027 2,513 3,318 1,505 2,388
M 95/85 3.7 3.35 9.72 705 931 8.80 638 842 382 606
95 85 6,273 3,137 4,140 5,675 2,837 3,745 1,699 2,695
M 100/90 3.9 3.54 10.84 786 1,038 9.86 715 944 428 679
100 90 6,995 3,497 4,616 6,362 3,181 4,199 1,905 3,022
M 105/95 4.1 3.74 12.02 872 1,151 10.99 797 1,052 477 757
105 95 7,755 3,878 5,119 7,088 3,544 4,678 2,122 3,367
M 110/100 4.3 3.94 13.26 962 1,269 12.17 883 1,165 529 839
110 100 8,556 4,278 5,647 7,854 3,927 5,184 2,351 3,731
M 115/105 4.5 4.13 14.56 1,056 1,394 13.42 973 1,285 583 925
115 105 9,395 4,697 6,201 8,659 4,330 5,715 2,593 4,113
M 120/110 4.7 4.33 15.92 1,155 1,524 14.73 1,068 1,410 640 1,015
120 110 10,274 5,137 6,781 9,503 4,752 6,272 2,845 4,514
M 125/115 4.9 4.53 17.35 1,258 1,661 16.10 1,168 1,541 699 1,109
125 115 11,191 5,596 7,386 10,387 5,193 6,855 3,110 4,934
M 130/120 5.1 4.72 18.83 1,366 1,803 17.53 1,271 1,678 761 1,208
130 120 12,149 6,074 8,018 11,310 5,655 7,464 3,386 5,372
M 135/125 5.3 4.92 20.37 1,478 1,950 19.02 1,379 1,821 826 1,310
135 125 13,145 6,573 8,676 12,272 6,136 8,099 3,674 5,829
M 140/130 5.5 5.12 21.98 1,594 2,104 20.57 1,492 1,969 893 1,417
140 130 14,181 7,090 9,359 13,273 6,637 8,760 3,974 6,305
M 145/135 5.7 5.31 23.65 1,715 2,264 22.19 1,609 2,124 963 1,528
145 135 15,256 7,628 10,069 14,314 7,157 9,447 4,286 6,799
M 150/140 5.9 5.51 25.37 1,840 2,429 23.86 1,730 2,284 1,036 1,644
150 140 16,370 8,185 10,804 15,394 7,697 10,160 4,609 7,312
M 155/145 6.1 5.71 27.16 1,970 2,600 25.60 1,856 2,450 1,111 1,763
155 145 17,524 8,762 11,566 16,513 8,256 10,899 4,944 7,844
M 160/150 6.3 5.91 29.01 2,104 2,777 27.39 1,986 2,622 1,189 1,887
160 150 18,716 9,358 12,353 17,671 8,836 11,663 5,291 8,394
M 165/155 6.5 6.10 30.92 2,242 2,960 29.25 2,121 2,800 1,270 2,015
165 155 19,948 9,974 13,166 18,869 9,435 12,454 5,649 8,963
The recommended design capacities are based on AISC/ASD and AASHTO/LRFD design methodologies for steel structures and retaining walls. Additional reduction factors from EN1993-5 are
applied to the tie rods based on their ability to articulate.
Nominal Outer Average Inner Effective Outer Cross Ultimate Yield Approx. Major Nominal
Bar Diameter Diameter Diameter Sectional Area Load Load Thread Diameter Weight
Designation in in in in2 kips kips in lbs/ft
(mm) (mm) (mm) (mm2) (kN) (kN) (mm) (kg/m)
Please note: As we continuously improve the design of our products, product details are subject to change.
A B A C
Size OD L
“T” Threaded Hollow Bar Couplers “T” Threaded Hollow Bar Hex Nuts Hollow Bar Centralizers
“R” Threaded Hollow Bar Couplers “R” Threaded Hollow Bar Hex Nuts
OD L Weight A B Weight
Bar Bar
Designation in in lbs Designation in in lbs
(mm) (mm) (kg) (mm) (mm) (kg)
Please note: As we continuously improve the design of our products, product details are subject to change.
A A
OD L
L
“T” Threaded Hollow Bar Couplers* “T” Threaded Hollow Bar Anchor Hex Nuts*
OD L Weight A L Weight
Bar Bar
Designation in in lbs Designation in in lbs
(mm) (mm) (kg) (mm) (mm) (kg)
HBC 760 3.75 7.875 34.81 HBAN 760 4.00 3.1 23.81
95.25 200.03 15.79 101.6 78.7 10.80
Carbide Cross, Steel Cross Cut , and Button Bits Drill Bit Adaptors
Cross External
Outside Thickness Inside Weight Sectional Total Area Internal Surface Moment Section
Diameter Diameter Area of Shaft Volume Area of Inertia Modulus
in in in lbs/ft in2 in2 ft3/ft ft2/ft in4 in3
mm mm mm kg/m cm2 cm2 m3/m m2/m cm4 cm3
5.500 0.415 4.670 22.56 6.63 23.76 0.12 1.44 21.57 7.84
139.700 10.541 118.618 33.57 42.77 153.28 0.011 0.44 897.80 128.47
6.625 0.432 5.761 28.60 8.40 34.47 0.18 1.73 40.49 12.22
168.275 10.973 146.329 42.56 54.23 222.40 0.017 0.53 1685.31 200.25
7.000 0.408 6.184 28.75 8.45 38.48 0.21 1.83 46.07 13.16
177.800 10.363 157.073 42.79 54.51 248.29 0.019 0.56 1917.56 215.65 Cross Sectional Area
7.000 0.453 6.094 31.70 9.32 38.48 0.20 1.83 50.16 14.33
177.800 11.506 154.787 47.18 60.11 248.29 0.019 0.56 2087.80 234.83
7.000 0.500 6.000 34.74 10.21 38.48 0.20 1.83 54.24 15.50
177.800 12.700 152.400 51.70 65.87 248.29 0.018 0.56 2257.62 254.00
7.625 0.430 6.765 33.07 9.72 45.66 0.25 2.00 63.12 16.56
193.675 10.922 171.831 49.21 62.71 294.60 0.023 0.61 2627.23 271.31
7.625 0.500 6.625 38.08 11.19 45.66 0.24 2.00 71.37 18.72
193.675 12.700 168.275 56.67 72.21 294.60 0.022 0.61 2970.62 306.76
Total Area of Shaft
8.625 0.500 7.625 43.43 12.76 58.43 0.32 2.26 105.72 24.51
219.075 12.700 193.675 64.63 82.34 376.94 0.029 0.69 4400.36 401.65
8.625 0.562 7.501 48.44 14.24 58.43 0.31 2.26 116.25 26.96
219.075 14.275 190.525 72.09 91.84 376.94 0.029 0.69 4838.65 441.79
9.625 0.472 8.681 46.18 13.57 72.76 0.41 2.52 142.51 29.61
244.475 11.989 220.497 68.73 87.56 469.42 0.038 0.77 5931.67 485.22
9.625 0.545 8.535 52.90 15.55 72.76 0.40 2.52 160.80 33.41
244.475 13.843 216.789 78.73 100.30 469.42 0.037 0.77 6692.95 547.49
10.750 0.500 9.750 54.79 16.10 90.76 0.52 2.81 211.95 39.43
273.050 12.700 247.650 81.54 103.87 585.56 0.048 0.86 8821.95 646.14
10.75 0.545 9.660 59.46 17.47 90.76 0.51 2.81 228.10 42.44
273.050 13.843 245.364 88.49 112.73 585.56 0.047 0.86 9494.16 695.46
External Surface Area
10.75 0.595 9.560 64.59 18.98 90.76 0.50 2.81 245.53 45.68
273.050 15.113 242.824 96.12 122.47 585.56 0.046 0.86 10219.65 748.56
11.875 0.582 10.711 70.26 20.65 110.75 0.63 3.11 330.04 55.59
301.624 14.783 272.059 104.56 133.21 714.53 0.058 0.95 13737.19 910.95
12.75 0.500 11.750 65.48 19.24 127.68 0.75 3.34 361.54 56.71
323.849 12.700 298.449 97.45 124.14 823.71 0.070 1.02 15048.31 929.31
13.375 0.480 12.415 66.17 19.45 140.50 0.84 3.50 404.73 60.52
339.724 12.192 315.340 98.47 125.45 906.45 0.078 1.07 16846.00 991.74
13.375 0.514 12.347 70.67 20.77 140.50 0.83 3.50 430.07 64.31
339.724 13.056 313.613 105.17 133.98 906.45 0.077 1.07 17900.72 1053.85
Contact your Skyline Steel representative for additional diameters, lengths, and starter details.
Micropile casing installed with fully threaded Female and male casing cut and bundled to Saver-subs available to fit all sizes of casing
75 ksi bar reinforcement specifications
Please note: As we continuously improve the design of our products, product details are subject to change.
Casing Accessories
Skyline Steel’s Geostructural Group is positioned to deliver complete accessory packages with
your threaded casing. We understand the urgency of your project and stock a wide range of
casing accessories for immediate delivery.
Tooling Items
Custom machining is available for duplex and flange adapters to match casing, drill, and drill
system requirements. We can also fabricate crossover subs to fit any existing tooling items.
Skyline Steel offers the following tooling items for the installation of micropile casing:
Air Swivels API Crossover Subs API Drill Rods (2 3/8 in to 6 5/8 in)
Breakout Wrenches Casing Crowns Cushion Subs
Diverter Heads Downhole Hammers Downhole Hammer Bits
Drag Bits Floating Subs Flushing Heads
Grout Swivels Ictology Bits Stabilizers
Tricone Bits
Casing accessories include duplex and flange adapters Downhole hammers and bits are available in various API drill rods and casing subs are typical tooling items
sizes and shank configurations
Please note: As we continuously improve the design of our products, product details are subject to change.
1
0.217 58.6 46.9 35.2 29.3 0.74
140 261 209 156 130 1.10
2
0.434 117.2 93.8 70.3 58.6 1.48
280 521 417 313 261 2.20
3
0.651 175.8 140.6 105.5 87.9 2.22
420 782 626 469 391 3.31
4
0.868 234.4 187.5 140.6 117.2 2.96
560 1043 834 626 521 4.41
5
1.085 293.0 234.4 175.8 146.5 3.70
700 1303 1043 782 652 5.51
6
1.302 351.6 281.3 211.0 175.8 4.44
840 1564 1251 938 782 6.61
7
1.519 410.2 328.2 246.1 205.1 5.18
980 1825 1460 1095 912 7.71
8
1.736 468.8 375.0 281.3 234.4 5.92
1120 2085 1668 1251 1043 8.82
9
1.953 527.4 421.9 316.4 263.7 6.66
1260 2346 1877 1408 1173 9.92
10
2.170 586.0 468.8 351.6 293.0 7.40
1400 2607 2085 1564 1303 11.02
11
2.387 644.6 515.7 386.8 322.3 8.14
1540 2867 2294 1720 1434 12.12
12
2.604 703.2 562.6 421.9 351.6 8.88
1680 3128 2503 1877 1564 13.22
13
2.821 761.8 609.4 457.1 380.9 9.62
1820 3389 2711 2033 1694 14.33
14
3.038 820.4 656.3 492.2 410.2 10.36
1960 3649 2920 2190 1825 15.43
15
3.255 879.0 703.2 527.4 439.5 11.10
2100 3910 3128 2346 1955 16.53
16
3.472 937.6 750.1 562.6 468.8 11.84
2240 4171 3337 2503 2085 17.63
17
3.689 996.2 797.0 597.7 498.1 12.58
2380 4432 3545 2659 2216 18.73
18
3.906 1054.8 843.8 632.9 527.4 13.32
2520 4692 3754 2815 2346 19.84
19
4.123 1113.4 890.7 668.0 556.7 14.06
2660 4953 3962 2972 2476 20.94
Please note: As we continuously improve the design of our products, product details are subject to change.
STEEL ANCHORHEAD AØ
CAP (OPTIONAL)
GR50 OR A36
BEARING PLATE**
H
A500
STEEL TRUMPET PIPE
16” Typ.
AASHTO M252
HDPE CORRUGATED
SHEATH
Max. No of OD ID OD ID AØ H OD Height
Strands
in in in in in in in in
mm mm mm mm mm mm mm mm
For technical questions and engineering support, please contact us via our technical hotline at:
1-866-875-9546 or email us at: engineering@skylinesteel.com.
02/17 Edition