Beruflich Dokumente
Kultur Dokumente
FinePix 3800
SERVICE MANUAL
US/CA-Model
WARNING
THE COMPORNENTS IDENTIFIED BY THE MARK “ ” ON THE SCHEMATHIC
DIAGRAM AND IN THE PARTS LIST ARE CRITICAL FOR SAFETY.
PLEASE REPLACE ONLY BY THE COMPONENTS SPECIFIED ON THE SCHEMATHIC
DIAGRAM AND IN THE PARTS LIST.
IF YOU USE WITH PART NUMBER UN-SPECIFIED, IT MAY RESULT IN A FIRE AND AN
ELECTORICAL SHOCK.
Ref.No.:ZM00449-100
FUJI PHOTO FILM CO.,LTD. Printed in Japan 2002.8(T.S.)
FinePix 3800 (US/CA) SERVICE MANUAL
SAFETY CHECK-OUT
After correcting the original problem, perform the following safety
check before return the product to the costomer.
1. Check the area of your repair for unsoldered or poorly 6. Make leakage - current measurements to determine
sol dered connections. Check the entire board sur that exposed parts are acceptably insulated from the
face for solder splasher and bridges. supply circuit before returning the product to the customer.
2. Check the interboard wiring to ensure that no wires 7. CAUTION: FOR CONTINUED
are “pinched” or contact high-wattage resistors. PROTECTION AGAINST FIRE
HAZARD, REPLACE ONLY WITH
SAME TYPE 2.5 AMPERES 125V
3. Look for unauthorized replacement parts, particu FUSE.
RISK OF FIRE-
larly tran sistors, that were installed during a previ 2.5A125V
REPLACE FUSE ATTENTION: AFIN D'ASSURER
AS MARKED UNE PROTECTION
ous repair. Point them out to the customer and rec 2.5A125V PERMANENTE CONTRE LES
ommend their replacement. RISQUES D'INCENDIE,
REMPLACER UNIQUEMENT
PAR UN FUSIBLE DE MEME,
4. Look for parts which, though functioning, show obvi TYPE 2.5 AMPERES, 125
ous signs of deterioration. Point them out to the cus VOLTS.
CONTENTS
1.General
4.Adjustment
3
1.General FinePix 3800 (US/CA) SERVICE MANUAL
1.General
1-1. Product specification
System
Model Digital Camera FinePix 3800
Number of effective pixels 3.2 million pixels
CCD sensor 1/2.7-inch square pixel CCD with RGB Filter
Number of total pixels: 3.34 million pixels
Number of recorded pixels 2048 × 1536 pixels/1600 × 1200 pixels/1280 × 960 pixels/ 640 × 480 pixels
File format Still image: JPEG (Exif Ver.2.2), DPOF-compatible
Movie: AVI format, Motion JPEG
* Design rule for Camera File system compliant
Viewfinder 0.33 inches 110,000 pixels electronic viewfinder
Lens Fujinon 6× optical zoom lens F2.8/F4.8/F8.2
Storage media xD-Picture Card (16MB to 128MB)
Focus distance f=6 mm-36 mm
(equivalent to 38 mm-228 mm on a 35 mm camera)
Exposure control 64 zones TTL metering, Program AE
(exposure compensation available in Manual mode)
Sensitivity Equivalent to ISO 100
White balance Auto (7 positions selectable in Manual mode)
Focal range Normal: Approx. 80 cm/2.6 ft. to infinity
Macro: Approx. 10 cm-80 cm/3.9 in.-2.6 ft.
Shutter speeds Variable-speed, 3 sec. to 1/1500 sec. (using AE)
Flash (Auto flash using Effective range: Wide Approx. 0.3 m-3.5 m (1.0 ft.-11.5 ft.)
flash control sensor) Tele Approx. 0.8 m-3.5 m (2.6 ft.-11.5 ft.)
Flash modes: Auto, Red-Eye Reduction, Forced Flash, Suppressed Flash, Slow
Synchro, Red-Eye Reduction + Slow Synchro
(when the pop-up flash is stowed: Suppressed Flash)
LCD monitor 1.8-inches, 62,000 pixels amorphous silicon TFT
Aperture F2.8/F4.8/F8.2 (Wide) (automatically selected)
Self-Timer Approx 10 sec. timer clock
Erase modoes Erase frame, Erase all frames, Format (initialize)
Number of frames recorded
Quality 3M F 3M N 2M 1M 0.3M
Number of recorded pixels 2048 1536 1600 1200 1280 960 640 480 320 240 160 120
Image Data Size Approx. 1300KB Approx. 590KB Approx. 390KB Approx. 320KB Approx. 130KB Movie
DPC-16 (16MB) 12 26 39 49 122 Approx. 94 sec. Approx. 5 min.
DPC-32 (32MB) 25 53 79 99 247 Approx. 191 sec. Approx. 10.1 min.
DPC-64 (64MB) 50 107 159 198 497 Approx. 6.4 min. Approx. 20.2 min.
DPC-128 (128MB) 102 215 319 398 997 Approx. 12.9 min. Approx. 40.6 min.
Input/Output Terminals
(USB) socket USB (1) for image data output with a personal computer
DC IN 5V (Power input) Socket for specified AC power adapter
socket
4
FinePix 3800 (US/CA) SERVICE MANUAL
1.General
Number of available Battery type Using LCD monitor Using EVF
shots using batteries
Alkaline batteries Approx. 300 frames* Approx. 320 frames *
Using (battery life)
Ni-MH batteries
HR-3UF Approx. 320 frames* Approx. 350 frames *
5
1.General FinePix 3800 (US/CA) SERVICE MANUAL
z Superb image quality provided by the high-resolution Fujinon 6× zoom lens and 3.2 million effective pixels
z Maximum number of recorded pixels: 2048 × 1536 pixels (3.15 million pixels)
z Compact and lightweight body
z Wide range of photography applications (includes Macro function)
z Intelligent Auto White Balance and AE functions built-in
z Built-in automatic flash with precise wide-range flash control
z 3.2× digital zoom photography (5× for movie shooting) and up to 12.8× zoom playback functions
z Manual and Scene Position modes that provide an expanded range of photography options
z 1.8 inches 62,000 pixels amorphous silicon TFT LCD monitor and 0.33 inches electronic viewfinder (EVF)
z Voice Caption function records up to 30 seconds of sound.
z Movie shooting function (320 × 240/160 × 120 pixels with sound)
z Easy high-speed image file transfer via the USB connection (using the Interface Set provided with sound)
z Accepts tele and wide conversion lenses. (Flash cannot be used when a conversion lens is mounted.)
z Conforms to the new standard for digital camera file system*
* Design rule for Camera File system
Explanation of Terms
DPOF: Digital Print Order Format
DPOF is a format used for recording information on a storage media (image
memory card, etc.) that allows you to specify which of the frames shot using a
digital camera are printed and how many prints are made of each image.
EV: A number that denotes exposure. The EV is determined by the brightness of the
subject and sensitivity (speed) of the film or CCD. The number is larger for bright
subjects and smaller for dark subjects. As the brightness of the subject changes, a
digital camera maintains the amount of light hitting the CCD at a constant level by
adjusting the aperture and shutter speed. When the amount of light striking the
CCD doubles, the EV increases by 1. Likewise, when the light is halved, the EV
decreases by 1.
JPEG: Joint Photographics Experts Group
A file format used for compressing and saving color images. The compression
ratio can be selected, but the higher the compression ratio, the poorer the quality
of the expanded image.
Motion JPEG: A type of AVI (Audio Video Interleave) file format that handles images and sound
as a single file. Images in the file are recorded in JPEG format. Motion JPEG can
be played back by QuickTime 3.0 or later.
PC Card: A generic term for cards that meet the PC Card Standard.
PC Card Standard: A standard for PC cards determined by the PCMCIA.
PCMCIA: Personal Computer Memory Card International Association (US).
White Balance: Whatever the kind of the light, the human eye adapts to it so that a white object still
looks white. On the other hand, devices such as digital cameras see a white sub-
ject as white by first adjusting the color balance to suit the color of the ambient
light around the subject. This adjustment is called matching the white balance. A
function that automatically matches the white balance is called an Automatic
White Balance function.
6
FinePix 3800 (US/CA) SERVICE MANUAL
1.General
1-3.Names of External Components
Mode dial
Power switch
Microphone
Shutter button
OPEN (Flash pop-up)
Self-timer lamp button
Strap mount
Flash
Flash control Slot cover
sensor
xD-Picture Card slot
DC IN 5V(Power input)
socket
Speaker
( Macro)button
( Flash)button
( Wide zoom)button
EVF/LCD
(monitor selector)
button Strap mount
MENU /OK button
Indicator lamp
BACK button
LCD monitor
DISP button
7
2. Disassembly FinePix 3800 (US/CA) SERVICE MANUAL
2. Disassembly
2-1.Names of internal Components
CABI REAR ASSY
EVF CONST
STROBE CONST
LCD ASSY
MSW PWB ASSY
RSW PWB ASSY
LCD FRAME
MAIN FRAME
LENS CONST
MACROHONE ASSY
SPEAKER ASSY
CABI FRONT ASSY
8
FinePix 3800 (US/CA) SERVICE MANUAL 2. Disassembly
2-2.Removing CABI R ASSY
<Step1>
3 2
2
*Reassemble CABI REAR in the state of the Manual
camera mode.
<Step2>
9
2. Disassembly FinePix 3800 (US/CA) SERVICE MANUAL
<Step1>
1
<Step2>
10
FinePix 3800 (US/CA) SERVICE MANUAL 2. Disassembly
2-5.Removing MAIN PWB ASSY.
Remove in the order indicated by circled numbers.
<Step1>
1 (1) Remove CN101 CN204, CN301, CN207and CN501.
(2) Remove MAIN PWB ASSY in the direction of the
2 arrow while removing the connector in A part.
A
1
1
<Step2> (note)
Make the power lever a turning off mode.
1
(1) Raise BATTERY HOLDER ASSY in the direction
of the arrow.
2 (3) Remove CN601.
11
2. Disassembly FinePix 3800 (US/CA) SERVICE MANUAL
<Step1>
2
<Step2>
<Step1>
(1) Remove three screws.
1 (2) Remove CCD EARTH PLATE, EARTH PLATE.
(3) Remove MAIN FRAME.
(4) Remove LENS CONST in the direction of the arrow.
4
12
FinePix 3800 (US/CA) SERVICE MANUAL 2. Disassembly
2-9.Removing STROBE CONST/ST TOP.
Remove in the order indicated by circled numbers.
<Step1>
1 (1) Remove one screws.
3
(2) Remove CN2.
2 (3) Remove SPEAKER BLOCK in the direction
of the arrow.
* Formation of harness
<Step2>
13
2. Disassembly FinePix 3800 (US/CA) SERVICE MANUAL
A RSW PWB
<Step1>
14
FinePix 3800 (US/CA) SERVICE MANUAL 3.Schematic
3.Schematic
3-1.Cautions
<Caution when replaceing chip (leadless) parts.>
* Do not re-use the removed parts, but use new parts.
Be careful that the negativ side of the tantalum capacitors are susceptible to heat.
* Voltage indications are omitted for capacitors other than chemical and tantalum capacitors
with a dielectric strength of 50 V or less.All units are uF (p shows pF).
* Chip resistors without indication are 1/10 W.
* k=1000 , M=1000 k
* Variable resistors and semi-variable resistor are abbreviated the specification of B characteristic.
15
3.Schematic FinePix 3800 (US/CA) SERVICE MANUAL
The FinePix 3800/S304 incorporates two new ICs - a intelligent highly integrated image processor IC (WCS:202).
The intelligent highly integrated image processor IC (WCS:202) is equivalent to the image signal processing IC (VCS:
IC209) incorporated in previous models of the FinePix 2800Zoom, however it provides a dramatic reduction in imaging/
playback interval time, and improved S/N ratio and image sharpness.
Time required for transfer of software via the USB interface is reduced due to the use of the WCS internal buffer.
16
3-4. Block Diagram
O.LPF
24.5MHz
D+,D-,VBUS
LENS ANALOG A/D USB USB
1/2.7 inch 3M BLOCK (12bit) 12
x 6 ZOOM
Various pulses
ADCLK EVF-Driver EVF
V H
IBUF IC403
6 2
EVF BL
V_DRV Timing Generator
DIGITAL
IC101 (Programable)
SHUTTER AVD,AHD
IRIS ADCK,FI
ZOOM CAM1-4 LCD LCD
AF LED BL
JPEG
Motor Drv.
IC301 MEDIA
TIMER CPU
Detection core
XD-Picture
Card
MSW PWB
ASSY
OFF/CAM/PB
S1/S2 KEY PWB
32.768kHz
+/- ASSY
STRB DISP SDRAM Flash ROM
MODE BACK
(128Mbit) (16Mbit)
DIAL MENU/OK (x32)
IC601 5.6V BATT
L/R/U/D IC203 IC204
5.0V back RTC PWR CTL EVR
RSW PWB up Block D/A
ASSY 3.3V
3.Schematic
8ch
BT601
CCD 1.5V RESET IC501
PIO AMP
PW CTL Block
Speaker
VDET
BATT DC block
PWR_ON IC IC352 Volume SP_AMP
DCDC_8.5V
AUDIO
MIC_AMP
DC IN FUSE
MIC
SO1,SI1,SCK1
17
FinePix 3800 (US/CA) SERVICE MANUAL
PC
CN851 CN901 RSW PWB ASSY
MIC ASSY
FFC FFC
CN203
CN206 XD-Picture
Card
CN602 CN201
LENS CONST
DCST PWB ASSY
CN301 FPC
FPC FPC
CN207
DC_IN
BATT_IN CN1
CN2 EVF CONST
SP ASSY
LCD ASSY
STROBE CONST
18
FinePix 3800(US/CA) SERVICE MANUAL 3.Schematic
3-6.Board mounting diagram
3-6-1.Printed wiring board of DCST PWB ASSY.
CN701 CN702
CN602
PS602 PS604
PS603 CN601
PS601
IC601
IC702 F601
C713
J601
19
3.Schematic FinePix 3800 (US/CA) SERVICE MANUAL
CN207
CN204
CN205
SW201 CN501 CN401
CN402
IC403
CN301
IC203
IC301
CN451
IC202
IC204
CN201
PS351
IC102
IC101
IC352 CN203
CN101
20
FinePix 3800(US/CA) SERVICE MANUAL 3.Schematic
3-6-3.Printed wiring board of RSW PWB CONST.
CN951
A
SW952
SW903
SW904
A
CN902
B
SW901 SW902
CN901
21
3.Schematic FinePix 3800 (US/CA) SERVICE MANUAL
SW856
SW855 SW858
A B
SW851
SW857
SW854
SW853
CN851
SW852
IC1(CCD)
CN801
22
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
4.Adjustment
4-1.Important point Adjustment when Replacing Major Parts
Adjust the item shown by in the table below at the part replacement of MAIN PWB ASSY, DCST PWB ASSY,
LENS CONST, and LCD ASSY. (Other part replacements need not be adjusted. )
Replacing parts
Adjustment item MAIN PWB ASSY DCST PWB ASSY LENS CONST LCD ASSY
Battery adjustment
LCD adjustment
CCD Defect correction adjustment
CAM adjustment
AF adjustment
Flash adjustment
End setting (Do the end setting when you end the adjustment software when you set the camera to the Jig mode. )
When you replace MAIN PWB ASSY: CAM adjustment -->AF adjustment --> CCD defect correction adjustment -->
Battery adjustment -->LCD adjustment -->Flash adjustment --> End setting.
When you replace LENS CONST: CAM adjustment -->AF adjustment --> CCD defect correction adjustment -->
Flash adjustment --> End setting.
When you replace DCST PWB ASSY: Battery adjustment -->LCD adjustment -->Flash adjustment --> End setting.
When you replace LCD ASSY: LCD adjustment --> End setting.
(Note1) It is a type that the harness of POWER CABLE JIG so far becomes long.
The adjustment is possible even by past POWER CABLE JIG.
(Note2) Please downloaded from Web server (http://fujifilm-di.intranets.com/).
23
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
DC_5V
DC IN terminal
USB terminal
Voltmeter
(Note 1)
(sensing)
Note 1: Always check the input voltage in the vicinity of the DC IN terminal when adjusting.
1. Brightness:
160±5cd/m2 (with LB140 filter)
No chart, center of pattern box
Filter(LB140)
Minolta brightness meter LS-110 or equivalent
24
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
(2)Environmental setting for Flash Adjustment (Fig.B)
As Flash adjustment is easily affected by external light,
1000mm +-10mm
the area around the gray chart should be as dark as pos-
sible.
The chart is mounted at a distance of 1000 mm from the
reference face of the camera.
An Oxford Gray (No.22) chart (manufactured by Superi- Center
or) with a reflectivity of 18±0.7% is used as the gray
chart.
Baseplat e (∑-13-3/Sigma
<Conversion Lens Unit>
Optical Equipment)
900mm +-5mm
<Fig.C> Environmental setting for AF Adjustment
(4) Environmental setting for LCD adjustment (Fig.D)
1) Fit the sensor of LCD adjustment Jig to the center of
FinePix 3800/S304 LCD Monitor
the LCD monitor.
2) Shade from the fluorescent lamp to the LCD monitor part.
MENU
/OK
* Make the LCD monitor part a darkroom condition as
much as possible. BACK
DISP
FinePix
4-7.Various downloading software decompres-
sions, preservation methods, and notes
<Fig.D> Environmental setting for LCD Adjustment
<Step1>
Download compressed PC adjustment software <Fig.E-1>
(ZJ00578-100.ZIP) from Web server (http://fujifilm-
di.intranets.com/).<Fig.E-1>
25
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
<Step2>
Defrost the downloaded compression software. My Computer
(Note) 3.5inch FD(A:)
*Specify the preservation drive for C drive if it is decom- (C:)
pression software which can specify the preservation
drive. ZJ00578-100
*Similarly, defrost without making a new folder if it is de-
compression software which can be defrosted without
FinePix3800_U
making a new folder.
*Defrost simply if the decompression software which you <Fig.E-2>
have cannot specify the drive specification and the folder
making.
My Computer
<Step3>
The folder named ZJ00578-100 can be made by de- 3.5inch FD(A:)
frosting without specifying anything. <Fig.E-2>
Then, copy the folder named FinePix3800_U in this
(C:)
folder in C drive.(Fig.E-3) ZJ00578-100
The folder of ZJ00578-100 becomes unnecessary at the
end, and delete this folder. FinePix3800_U
<Fig.E-3>
(2) Download and preservation method of LCD adjust-
ment image
<Step2>
Defrost the downloaded compression software
<Step3>
As the folder named ZJ00579-100 can be made by sim-
ply defrosting;(fig.E-4)
All files are copied in xD-Picture Card (more than 16MB,
3.3V) in this folder including the folder named Dcim.
(Caution)[Important]
(a) PC adjustment software can not start when there is folder of
FinePix3800_U in folder named ZJ00578-100.(Fig.E-2)
Please preserve the folder of FinePix3800_U right under C drive.(Fig.E-3)
(b) Please do not change the foldername named FinePix3800_U.
PC adjustment software can not start when foldername is changed.
(d) LCD adjustment should use xD-Picture Card.
(e) Please format xD-Picture Card with the camera.
(f) When the folder named Dcim is changed, the LCD adjustment cannot adjust.
26
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
4-8.Install the DSC jig driver and the PC adjust-
(1) (2)
ment software.
* Since this camera uses the USB for communications
with the personal computer, in order to start the PC ad-
justment software, [the DSC jig driver] needs to be in-
stalled in the personal computer beforehand.
* The DSC jig driver is the same as that for the FinePix
6800Z, so if this jig driver software is already installed in
the personal computer, it is not necessary to install it.
The procedure is given below.
<Step 1>
DSC jig driver(ZJ00476-100.ZIP) is downloaded from
Web server (http://fujifilm-di.intranets.com/).
<Step 3>
Double-click setup.exe in the folder of defrosted
ZJ00476-100 and install Fuji FILM DSC Jig Driver as fol-
lows.
<Step 4>
Install the software in [C:\ProgramFiles\Fjig]
according to the instructions on the PC's screen.
27
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
<Step 1>
Double-click on the executable file FFW.exe (Fig.E-(1)) to
display the FFW Start-up Screen (Fig.F). <Fig.F> FFW.EXE Start-up Screen
<Step 2>
(1)
Select the Setting menu (Fig.G-(1)) from the menu bar on the (2)
Menu screen, and then select Mode setting (Fig.G-(2)).
<Step 3>
Fx3800z_u
Select the EVR menu (Fig.H-(1)) from the Customize dialog
screen, and setup as follows (Fig.H-(2)).
Item Setup details
etc (-V2) Use (=check)
LANC page Use (=check)
<Step 4>
Select the Etc menu (Fig.I-(1)) from the Customize dialog
screen, and setup as follows (Fig.I-(2)).
Item Setup details
Number of automatic measurements 0
Enable mode change No check (=un used)
Use Japanese fonts No check (=un used)
Fx3800z_u Fx3800z_u
Apply Apply
<Fig.I> Etc Dialog Box Screen <Fig.H> EVR Dialog Box Screen (2)
28
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
<Step 5> (2) (1)
Select Hardware from the Customize Setup Screen (Fig.J-
(1)). Setup as follows on the Hardware menu (Fig.J-(2)).
fx2800z_ue
<Step 6>
When setup on the three menus noted above (EVR, Etc, Hard
ware) is complete, click on Apply (Fig.J-(3)) on the Customize
dialog screen to finish.
After the setup has been applied, further setup is unnecessary.
Note:
Setting Disable OKNG Display to OFF on the screen shown in Apply
29
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
Fig.1
—> The [Cautions When Using the Adjustment Software] screen appears.
<Step 3>
Fig.2
30
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
<Step 4>
<Fig.3>
<Note>
(1) [F3] LCD Adjustment cannot be run unless the LCD flicker image xD-Picture card is inserted into the camera.
(2) [F1] Battery Adjustment cannot be run unless the PC Jack Cable Jig is used to supply power to the camera.
<Step 5>
Fig.4
<Note>
(1) The firmware version as of August 20th, 2002 is ‘1.27’. A separate instruction will be issued if the firmware requires
upgrading.
(2) The firmware for this camera is not upgraded with the use of SmartMedia as is the case with previous models. See ‘[F8]
Firmware Download’ on page 40 for details of upgrading the firmware.
31
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
<Step 6>
<Fig.5>
<Note>
(1) ‘Fx3800 U PC Software Ver.1.27’ at the bottom-right of the screen indicates the version number of the adjustment
software.
(2) Always run CCD Defect Correction Adjustment following CAM Adjustment.
Reason: CCD defect correction adjustment may not have been run correctly.
(3) After running firmware download, other adjustments may be required depending on the content of the download soft-
ware. In such cases, the items to be adjusted, and the sequence of adjustment, will be indicated separately.
(4) After starting the adjustment software and beginning communication with the camera, always run End Setting following
adjustment and before returning the camera to the customer. If the End Setting is not run, the PC will not recognize the
camera when the two are connected.
Reason: As the camera will remain in the Jig mode (repair mode), it will not be recognized with the normal camera
drivers.
32
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
4-11. [F5] CAM Adjustment
(shutter adjustment, adjustment for reduced aperture sensitivity, ISO sensitivity adjustment, white balance adjust-
ment, AE adjustment, offset level adjustment)
<Step 1>
Select [F5] CAM Adjustment on the [Adjustment Items Select] screen (Fig.6).
—> The [CAM Adjustment Preparation] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
Fig.6
<Note>
An error will occur during CAM adjustment, and adjustment cannot be completed, unless the pattern box is calibrated
correctly.
—> The [CAM Adjustment (without filter)] screen appears.
<Step 3>
Fig.7
33
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
<Step 4>
Fig.8
<Step 5>
Fig.9
—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
—> The [CAM Adjustment Complete] screen appears.
<Note>
CAM adjustment may be terminated if adjustment is continued without removing the LB140 filter. Always ensure that the
LB140 filter is removed before proceeding with adjustment.
34
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
<Step 6>
Fig.10
Fig.11
35
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
<Step 3>
Fig.12
—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
—> The [CCD Defect Correction Adjustment Complete] screen appears.
<Step 4>
Fig.13
36
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
4-13. [F6] AF Adjustment
<Step 1>
Select [F6] AF Adjustment on the [Adjustment Items Select] screen (Fig.6).
—> The [AF Adjustment Preparation] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
Fig.14
<Note>
Always use a 900mm conversion lens.
Fig.15
—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
—> The [AF Adjustment Complete] screen appears.
37
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
<Step 4>
Fig.16
Fig.17
38
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
<Step 3>
Fig.18
<Step 4>
Fig.19
39
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
<Step 5>
Fig.20
—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
—> The [Battery Voltage Adjustment Complete] screen appears.
<Step 6>
Fig.21
40
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
4-15 [F3] LCD Adjustment
<Step 1>
Select [F3] LCD Adjustment on the [Adjustment Items Select] screen (Fig.6).
—> The [LCD Adjustment Preparation] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
Fig.22
<Note>
(1) Refer to the Setup Manual supplied with the jig for details of setting up the LCD automatic adjustment jig with the PC.
(2) If the LCD flicker image xD-Picture card has not been inserted in the camera, return to the [Jig Mode Setup] screen, select
the Jig mode again, and run LCD Adjustment.
<Step 3>
Fig.23
—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
—> The [LCD Adjustment Complete] screen appears.
41
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
<Step 4>
Fig.24
Fig.25
—> The [Flash Adjustment Start] screen appears.
42
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
<Step 3>
Fig.26
—> Write the adjustment data to the flash ROM when adjustment has been completed correctly.
—> The [Flash Adjustment Complete] screen appears.
<Step 4>
Fig.27
43
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
Fig.28
<Step 3>
Fig.29
44
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
<Step 4>
Fig.30
<Note>
This example assumes that <A>USA has been selected. The following screen therefore appears.
—> The [USA_ID USA] screen appears.
<Step 5>
Fig.31
45
4.Adjustment FinePix 3800 (US/CA) SERVICE MANUAL
<Step 6>
Fig.32
<Step 7>
Fig.33
46
FinePix 3800(US/CA) SERVICE MANUAL 4.Adjustment
4-18 [F8] Firmware Download
<Step 1>
Select [F8] Firmware Download on the [Adjustment Items Select] screen (Fig.6).
—> The [Firmware Download Start] screen appears.
<Step 2>
Run the adjustment in accordance with the instructions on the screen.
Fig.34
<Step 3>
Fig.35
47
5.Inspection FinePix 3800 (US/CA) SERVICE MANUAL
5. Inspection
5-1. Required Measuring Equipment
Measuring equipment Remarks
Power supply AC adapter (AC-5VH), stabilized power supply
Digital voltmeter For general use
Ammeter For general use (able to measure 1mA or less)
power cable jig For general use
xD-Picture card For general use
Power supply
FinePix 3800 Ammeter (AC-5VH, stabilized power supply)
2 Power supply Auto (1) Place battery in camera. (1) Approximately 4.5V with
switch photography (2) Insert xD-Picture card four AA-sized batteries.
LCD_ON and close cover. (2) Recording check card.
(3) Set mode dial to still
photography mode.
(4) Switch power supply ON. (4) Power supply LED is
green and beeps.
(5) If the date set message (5) Through screen and text
appears, press Cancel. display in EVF.
3 Check LCD Auto (1) Press EVF/LCD button. (1) Check that EVF is
photography extinguished, and that
through screen appears
on LCD monitor.
4 Check Movie Auto (1) Apply an appropriate (1) No problem with display LCD monitor
mode shock noise photography shock to the camera. on LCD monitor.
LCD_ON * Do not apply shock Restoration possible
directly to the lens or card despite disruption of sync.
cover.
48
FinePix 3800 (US/CA) SERVICE MANUAL 5.Inspection
Preparations for adjustment Method of adjustment Measuring Measurement points
Sequence Item Mode
(measurement points, subject, other) (VRs,waveforms,requiredvalues) equipment and jigs (VRs, positions)
5 Check macro Auto (1) Macro photography (1) Macro icon appears in
photography photography distance (approximately LCD monitor.
Check focus LCD_ON 10~80cm). (2) LED beside viewfinder
(2) Press shutter button to changes from green to
take photographs. orange (recording) to
green.
6 Movie/audio Movie (1) Select Movie mode. (1) Standby display on LCD.
recording check photography (2) Half-press shutter button (2) Movie/audio recording
LCD_ON -> full-press -> full-press begins. Recording
-> half-press -> release. displayed on LCD.
(3) Half-press five seconds (3) Movie/audio recording
later -> release. completed. Recording on
xD-Picture card.
8 Card cover detect M mode (1) Open card cover to check (1) Switch power OFF. LCD monitor
check LCD_ON recording.
(2) Remove xD-Picture card.
Delete mode Delete (1) Select <Delete all frames> (1) [OK to delete all
10 check from the menu, and press frames?] displayed.
the <OK> button.
(2) Press the <OK> button (2) Movie/photography
again. screen extinguished.
11 Battery low check Movie (1) Connect power cable jig Refer to Battery Adjustment Power supply
for connection details. cable jig
(2) Set voltage. (2) Set voltage to 4.5±0.3V. Stabilized
(3) Set mode dial to Replay (3) Starts normally. power supply
mode, and switch main
power ON.
(4) Set to pre-end voltage. (4) Set voltage to
3.7±0.02V. Battery
warning displayed.
(5) Set to end voltage. (5) Set voltage to
3.5±0.02V. Lens
retracts and main power
switched OFF.
12 Current Auto (1) Connect power cable jig. Ammeter
consumption photography (2) Set voltage. (2) Set voltage to 5.00±0.05V.
check LCD_ON (3) Set mode dial to Camera
mode, and switch main
power ON.
(4) Press the <EVF/LCD>
button to switch the LCD
monitor ON.
(5) After the through screen (5) Maximum current
is displayed, check consumption 450mA.
current consumption.
13 Leak current Power (1) Switch power OFF. (1) Maximum leak current Ammeter
OFF 1mA.
14 Factory setting Playback (1) Set mode dial to Playback * Setting and clearing date
mode. (1) Connect the USB cable
(2) Return all settings to initial from the PC to the camera
values. (ensure that the PC is
Flash: Auto switched ON).
Monitor brightness: Center (2) Open the card cover and
Power saving: OFF switch power ON
USB setting: Cardreader (POWER_ON) while
Beep: LOW pressing the shutter
Pixels: 1M normal button.
Photography mode:A mode (3) Switch power OFF
Date: Not set (POWER_OFF).
(3) Inspection battery/ (4) Check that the date has
inspection xD-Picture card been cleared.
not inserted in camera.
(4) Battery cover closed.
(5) LCD/EVF surface free of
contamination.
(6) Clean exterior of camera.
49
6.Parts List FinePix 3800 (US/CA) SERVICE MANUAL
6.Parts List
6-1.Packing and Accessories
6-1-1.Packing and Accessories(US model)
A117 A116
A107 A114
A106
A112
A113 A105
A111
A102
A115
A110
A118 A103
A101
A109
A104
A108
Ref No. Parts No. Description Note Ref No. Parts No. Description Note
50
FinePix 3800(US/CA) SERVICE MANUAL 6.Parts List
6-1-2.Packing and Accessories(CA model)
A117 A116
A107 A114
A106
A113
A105
A112
A111 A102
A115
A110
A118 A103
A101
A109
A104
A108
Ref No. Parts No. Description Note Ref No. Parts No. Description Note
51
6.Parts List FinePix 3800 (US/CA) SERVICE MANUAL
M217
B
M216
C
D
A
N.S
M218
M219
M207 M213
M208 M212
M209 M211
M210 K
M221 M203
M220
M204
M201
M215
M205
M202
Ref No. Parts No. Description Note Ref No. Parts No. Description Note
(Note 1) Do not attach M423 to CABI REAR ASSY when you use M222A.
Attach M423 to CABI REAR ASSY when you use M222B.
52
FinePix 3800(US/CA) SERVICE MANUAL 6.Parts List
6-3.Internal block (US/CA model)
M327
M309
G M324
M313 C I
M312
M311 E M323 M322
H
M309
M310 M326
E
M301 J
O
H
I
B L
M305 L
M304 D
K
N G
M303 M M325
M322
M306 N
N.S. M320
M321
M318
M302 M317
M307
N.S. M308 M319
M314
J M319
M
M316
M315
N.S.:Not Supply
Ref No. Parts No. Description Note Ref No. Parts No. Description Note
53
6.Parts List FinePix 3800 (US/CA) SERVICE MANUAL
M405
M408
M420 M421
M416
M409
M406
M414
M412 M422
M413
M415 M411
M401 M403
M404
M410
M419
M418
M403 M403
M407
O M417
M402
M423 (Note 1)
M422
Ref No. Parts No. Description Note Ref No. Parts No. Description Note
54
FinePix 3800(US/CA) SERVICE MANUAL 6.Parts List
6-5.Electrical Parts (US/CA model)
[NOTE]
The components indicated by mark are critical for safety. * Due to standardization,replacement in the parts list may be
When indicated parts by reference number,please include different form the parts list specified in the circuit or the
the board name. components used on the set.
55
7.Appendix FinePix 3800 (US/CA) SERVICE MANUAL
7. Appendix
7-1.List of Related Technical Updates Issued
To ensure that after-sales srevice is performed accuratety, keep a record here of the technical updates
issued that cover this device.
56
FUJI PHOTO FILM CO., LTD.
26-30, Nishiazabu 2-chome, Minato-ku, Tokyo 106-8620, Japan.