Beruflich Dokumente
Kultur Dokumente
USER MANUAL
PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE USE.
WARNING
WARNING
Improper installation or use of your Roof Top Tent may result in serious injury or
Warning
Improper
death. Youinstallation
will need or use of these
to follow your Roof Top Tentinstructions
installation may result carefully
in serioustoinjury or
ensure
death. You
proper will needon
installation to your
follow these and
vehicle installation
safe useinstructions
of your Roofcarefully
Top Tent.toPlease
ensurecontact
proper
Improper
your installation
installation
vehicleon oryour
use of your Roof
vehicle
manufacturer and
forTop Tentuse
safe mayloading
specified result
of your in Roof
serious injury
Top
capacity or
Tent.
of death.
yourPlease
roofYourack.
will need
contactNot toall
yourfollow
these installation instructions carefully to ensure proper installation on your vehicle and safe use of your Roof
vehicle roof
factory manufacturer for specifiedroof
racks or aftermarket loading
barscapacity
can safely of your roof rack.tent
accommodate Not models.
all factory
Top Tent. Please contact your vehicle manufacturer for specified loading capacity of your roof rack. Not all
roof
factory racks
roof racksoror aftermarket roof
aftermarket roof bars
bars can can safely
safely accommodate
accommodate tent models.
tent models.
Any
Any elements
elements applied
applied on
on the
the vehicle
vehicle roof
roof changes
changes the
the normal
normal vehicle
vehicle handling. The
handling. The
ANYmanufacturer disclaims
ELEMENTS APPLIED allVEHICLE
ON THE responsibility in case
ROOF CHANGEScase of
ofTHE
accidents
NORMAL due to improper
VEHICLE use,THE
HANDLING.
manufacturer disclaims all responsibility in accidents due to improper use,
MANUFACTURER DISCLAIMS ALL RESPONSIBILITY IN CASE OF ACCIDENTS DUE TO IMPROPER USE,
improper
improper maintenance,
maintenance, or checking the tightness of the brackets regarding the
WRONG MAINTENANCE, OR NOTor checkingTHE
CHECKING the tightnessOF
TIGHTNESS of theFASTENING
THE brackets HARDWARE/
regarding the
installation
installation
BRACKETS ON THEof ROOF
of the roof
the roof rack
rack
RACK system.
system.
SYSTEM
For CLIMB
DO NOT your safety and protection,
ON LADDER ensureANGLE
UNTIL CORRECT correct
IS placement and angle
ACHIEVED (approx. of ladder.
30 degrees
For
between
your
ladder
safety and protection,
and ground).
ensure correct placement and angle of ladder.
DO NOT CLIMB ON LADDER UNTIL CORRECT ANGLE IS ACHIEVED (approx. 30 degrees
DO NOT CLIMB ON LADDER UNTIL CORRECT ANGLE IS ACHIEVED (approx. 30 degrees
between
between
NOTE:
ladder
ladder
If the angle
and
and
of the
ground).
ground).
ladder
NOTE:
is at 90NOTE:
degrees
IfIfthe
theangle
angle
and/or
ofnot
does of
the
the ladder
ladder
reach
isis
atat
9090
the ground,
degrees
degrees
you
and/or
will needand/
a ladder
does not reach the ground, you will need a ladder extension
or does not reach the ground, you will need a ladder extension or longer extendable
extension or longer extendable ladder (sold separately). or longer extendable
ladder (sold
ladder (sold separately).
separately).
4WD Supacentre - The wholesaler / manufacturer shall not be liable for special, indirect incidental or
Adventure
consequential Kingsincluding
damages - The wholesaler
but not limited/ to
manufacturer
lost profits. shall not be liable for special,
indirect incidental
Adventure Kings -orThe consequential
wholesaler damages including
/ manufacturer but not limited
shall to lost
be liable profits.
for special,
indirect incidental or consequential damages including but not limited to lost profits.
SAFETY WARNING
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THE TENT MATERIALS.
UNDER NO CIRCUMSTANCE SHOULD ANY NAKED FLAME SOURCES OR HEATING DEVICES
BE USED INSIDE OR NEAR THE TENT.
KEEP CAMP FIRES WELL AWAY FROM TENT.
KEEP A LOOK OUT FOR ANY AIRBORNE BURNING EMBERS THAT MAY COME
INTO CONTACT WITH THE TENT.
KEEP A FIRE EXTINGUISHER OR WATER BUCKET NEARBY.
DO NOT SMOKE WITHIN THE TENT.
DO NOT OPERATE ANY DEVICE WHICH BURNS FUEL INSIDE OF THE TENT.
KEEP EXIT CLEAR.
Inspections: During trips regularly check that all nuts and bolts attaching your Roof Top Tent to your vehicle
are tight and in good repair.
3
3
2 T050801878
55 mm Steel M8 Bolt
8 T050801879
40 mm Steel M6 Bolt
8 T050801885
2 T050801887
4 T050801880
8 T050801881
2 T050801888
44
There are two mounting options for the orientation of your new Roof Top Tent. Either the Roof Top Tent will
open so that the ladder extends off the back of your vehicle, “Rear Mounted”. Or alternatively the ladder
extends off the side of your vehicle, “Side Mounted”. Either orientation will work for larger vehicles, however,
TENT ORIENTATION ON YOUR VEHICLE
most sedans or smaller SUVs are better suited for the side mounted option.
NOTE:There
If the are
Roof two mounting
Top Tent optionsyou
is rear mounted, forwillthe orientation
need of yourchannels
to cut the mounting new Roof ToptheTent.
to suite width of
Either the Roof Top Tent will open so that the ladder extends off the back of your
the roof top tent base.
vehicle, ”Rear Mounted”. Or alternatively the ladder extends off the side of your vehicle,
”Side Mounted”. Either orientation will work for larger vehicles, however, most
sedans or smaller SUVs are better suited for the side mounted option. If the
Roof Top Tent is rear mounted, the mounting channels need to be cut to match
the width of the Roof Top Tent base. We will go over this in the next section.
66
3. Using the four supplied 40mm Steel M6 bolt, slide your hand between the base and mattress,
3. Using theand
four supplied
insert 40mm
the bolts with Steel M6into
washers bolt,
theslide your hand
pre-drilled holes.between the base
and mattress, and insert the bolts with washers into the pre-drilled holes.
4. Place mounting channels on exposed bolts. For side mounted orientation, ensure the
mounting channels are perpendicular to hinge side. For rear mounted orientation, ensure the
4. Place mounting channels
mounting channelson exposed
are parallel bolts. For
to hinge side mounted orientation, ensure
side.
the mounting channels
5. Slide the M6 NylockareNut
perpendicular to in
into the inner slot hinge side.ofFor
the centre rear mounted
the mounting channels, until they
orientation,
are ensure
aligned the
with mounting channels
the bolts sticking are parallel
through the base.toTighten
hinge the
side.
bolts firmly from below,
using the supplied 10mm wrench. If you chose a rear mounted orientation, you will notice
that the mounting channels extend (20cm) beyond the edges of the base. You will need to
5. Slide the M6 Nylock Nut into the inner slot in the center of the mounting channels,
mark each channel where they extend beyond the tent base and cut the mounting channels
until theyso
are aligned
they with
fit within thethe
tentbolts
base.sticking through the
Fasten mounting base.toTighten
channels base asthe bolts above.
described
firmly from below, using the supplied 10mm wrench. If you chose a rear mounted
orientation, you will notice that the mounting channels extend (20cm) beyond the
edges of the base. You will need to mark each channel where they extend beyond
40mm Steel M6 Bolt
the tent base and cut the mounting channels so they fit within the tent base. Fasten
Washer
mounting channels to base as described above.
M6 Nylock Nut
Aluminium Mounting Channel
77 Plate
Slide
M8 Nylock Nut
DIAGRAM A DIAGRAM A
DIAGRAM B
DIAGRAM C
DIAGRAM C
DIAGRAM C
99
WARNING – DISCLAIMER
Any elements applied on the vehicle roof changes the normal vehicle handling.
The manufacturer disclaims all responsibility in case of accidents due to improper use, wrong
Maintenance , or checking the tightness of the brackets regarding the installation of the roof rack
system.
Mounting Channel
M8 Nylock Nut
DIAGRAM D
DIAGRAM D
4. Attach the Roof Top Tent to your roof rack at the four points where the rack and mounting
4. Attach the Roof Top Tent to your roof rack at the four points where the rack and
channels cross. Tighten all eight bolts. It is important that you check all the mounting bolts
and bracketsmounting channels
periodically cross.
to ensure Tighten
they all eight
are securely bolts securely.
fastened It is important
to your base that you
and roof rack or
check all
after-market roof bars.the mounting bolts and brackets periodically to ensure they are securely
fastened to your base and roof rack or after-market roof bars.
5. After ensuring the Roof Top Tent is positioned correctly, and all eight bolts are tightened,
insert the rubber end caps into the ends of the mounting channel (this may require light taps
5. After ensuring the Roof Top Tent is positioned correctly, and all eight bolts are
from a hammer).
tightened securely, insert the rubber end caps into the ends of the mounting
channel (this may require light taps from a hammer).
10
10
Care Instructions
Clean only with cold water and soft brush - do not use soap or detergent.
Do not expose to petrol, oil or solvents.
WARRANTY
WARRANTY PERIOD:
Full 12 month warranty from date of purchase against all manufacturing defects.
TO MAKE A CLAIM, PLEASE ENSURE YOU RETAIN YOUR SALES RECEIPT OF PURCHASE
CALL 1800 88 39 64