Beruflich Dokumente
Kultur Dokumente
BDA20303
Lecture #03
3
TYPICAL GEAR BELT DRIVE BALL MILL
4
POWER TRANSMISSION SYSTEM
(BELT)
Objectives:
Students will be able to:
1. describe basic features of a drive/transmission belt
2. describe several types of drive/transmission belt
3. solve kinematics and belt tension problems of belt drive system
Learning topics:
• Introduction
• Type of transmission
belt.
• Belt drive geometry
• Belt drive system
arrangement
• Belt drive kinematics
• Belt tension
5
INTRODUCTION
7
APPLICATIONS
8
APPLICATIONS
11
ADVANTAGES
Compared to other form of power transmission, belt drive have these
advantages :
12
TYPES OF POWER TRANSMISSION BELT
13
V-BELT TERMINOLOGY
15
BELT LENGTH
r r
2
16
BELT LENGTH
α
18
BELT DRIVE SYSTEM ARRANGEMENT
Power from one shaft can be transmitted to another shaft using some of
these arrangement :
19
Compound
20
belting
21
BELT DRIVE KINEMATICS
Velocity Ratio, VR : is defined as the angular speed of the driven pulley to the
angular speed of the driver pulley.
ω driven ω 2 D1 ( D1 + t )
VR = = = =
ω driver ω1 D2 ( D2 + t )
belt speed, vb : is defined as the linear velocity of the belt. The magnitude of this
velocity corresponds to the magnitude of the linear velocity of a point on the pitch
diameter of each pulley.
D1 D2
vb = ω1 = ω2 22
2 2
EXAMPLE
Answers :
i. 1775 rpm
ii. 22.30 m/s
23
IN CLASS TUTORIAL
Given: A belt drive is used to transmit power from an electric motor to
a fan as shown in the figure below. The electric motor is rated
at 3000 rpm. The radii of motor’s and fan’s pulley is 20 mm
and 80 mm respectively.
Find: velocity ratio, VR , the operating speed (rpm) of the fan and
the belt speed. (m/s)
Answers :
i. 0.25
ii. 750 rpm
iii. 6.28 m/s or 394.8 m/min
24
BELT DRIVE KINEMATIC (Cont.’d)
Belt drive will slip if friction
force on the surface of contact
between belt and pulley is
reduced. This will cause the
pulley to rotate without holding
the belt. Normally slip is
expressed in percentage.
Consider a belt drive system with slip for the figure above. The
effective angular speed at driven pulley is :
26
BELT TENSION
TORQUE
torque = moment
= force x radius
M =F resultant xR
28
BELT ALIGNMENT
29
RPM AND VELOCITY MEASUREMENT
Tt
Tt
Ts
Ts
Tt, Ts = belt tension; Ts oppose the direction of motion of the belt measured relative
to the surface, while Tt acts in the direction of the relative belt motion;
because of friction, Tt > Ts.
μ = coefficient of static or kinetic friction between the belt and the surface of
contact.
β = angle of belt to surface contact, measured in radians
e = 2.718..., base of the natural logarithm
31
BELT TENSION (Cont.’d)
V - BELT TENSION
driven side µβ
sin(α / 2)
Tt = Ts e (V - belt)
Tt Ts
Tt, Ts = belt tension; Ts oppose the direction of motion of the belt measured relative
to the surface, while Tt acts in the direction of the relative belt motion;
because of friction, Tt > Ts.
μ = coefficient of static or kinetic friction between the belt and the surface of
contact.
β = angle of belt to surface contact, measured in radians
e = 2.718..., base of the natural logarithm
α = Groove angle measured in degree.
32
EXAMPLE
Answer : Ts = 51.1 N
Tt = 131.1 N
33
IN CLASS TUTORIAL
34
POSSIBLE QUESTIONS
35
STANDARDS
36
Motorcycle Chain vs Belt vs Shaft Drive
37
38
39
END
40