Beruflich Dokumente
Kultur Dokumente
Contents
Figures
Figure 1-6 Front view of the BTS3012AE cabinet under full configuration ....................................................1-8
Figure 1-7 Installation space for a BTS3012AE cabinet (in mm) ....................................................................1-9
Figure 3-4 Installation holes of the expansion bolts for a single cabinet..........................................................3-6
Figure 3-13 Fastening the cabinet on the base (Rear view) ............................................................................3-13
Figure 3-21 Process for installing a cabinet on the cement floor with insufficient bearing capacity .............3-19
Figure 3-22 Installation position of the BTS3012AE cabinet.........................................................................3-20
Figure 3-24 Fastening the U-bar supports on the cement plinths ...................................................................3-22
Figure 3-29 Fastening the cabinet on the base (Rear view) ............................................................................3-26
Figure 4-5 Hooking spanners on to the square holes of the subrack ................................................................4-7
Figure 5-2 Positions of the dummy panel and air deflector plate .....................................................................5-2
Figure 6-9 Power cable layout of the single-phase mains input .......................................................................6-6
Figure 6-10 Connection of power cables in single-phase mains and single-phase generator input modes ......6-7
Figure 6-11 Connection of power cables in three-phase mains input mode .....................................................6-8
Figure 6-12 Connection of power cables in three-phase mains and three-phase generator input mode ...........6-9
Figure 6-13 Installing the PGND cable for the power interface box ..............................................................6-12
Figure 6-14 75-ohm E1 coaxial cable.............................................................................................................6-13
Figure 6-17 Clamping the 120-ohm E1 cable to the 120-ohm digital unit .....................................................6-17
Figure 6-22 Structure of the RF RX signal cable and that of the TX signal cable..........................................6-22
Figure 6-23 Cable for the combiner on the DTRU .........................................................................................6-23
Figure 6-31 Cabling for the 100-AH configuration mode (1) ........................................................................6-30
Figure 6-32 Cabling for the 100-AH configuration mode (2) ........................................................................6-31
Figure 6-33 Cabling for the 150-AH configuration mode (1) ........................................................................6-33
Figure 6-34 Cabling for the 150-AH configuration mode (2) ........................................................................6-34
Figure 6-35 Cabling for the 150-AH configuration mode (3) ........................................................................6-35
Figure A-4 Connecting the cable core wires to the terminal crimping sleeve .................................................A-5
Figure A-5 Crimping molds for various power cables.....................................................................................A-5
Figure C-1 The label for the signal cable ........................................................................................................ C-2
Figure C-2 Label for power cables .................................................................................................................. C-3
Figure C-7 Printed parts on the label for signal cables.................................................................................... C-8
Figure C-8 Example of the label on the optical fiber between two devices .................................................... C-9
Figure C-9 Example of the label on the optical fiber between the device and the ODF................................ C-10
Figure C-10 Example of the label on the trunk cable between two devices .................................................. C-12
Figure C-11 Example of the label on the trunk cable between the device and the DDF ............................... C-13
Figure C-12 Example of the labels on the DC power cable .......................................................................... C-14
Tables
Table 6-5 Figure for reference in different power supply modes ......................................................................6-5
Table 6-6 Pins of the coaxial cable .................................................................................................................6-13
Table 6-7 Installation positions of the Boolean value input signal cable ........................................................6-26
Table C-2 Information on labels affixed to the fiber between two devices...................................................... C-8
Table C-3 Information on labels affixed to the fiber between the device and the ODF................................. C-10
Table C-4 Information on labels affixed to the trunk cable between two devices ......................................... C-11
Table C-5 Information on labels affixed to the trunk cable between the device and the DDF ...................... C-12