Beruflich Dokumente
Kultur Dokumente
Installation Guide
Legal Notices
This guide is copyrighted ©2012 by Avid Technology, Inc.,
(hereafter “Avid”), with all rights reserved. Under copyright
laws, this guide may not be duplicated in whole or in part
without the written consent of Avid.
003, 96 I/O, 96i I/O, 192 Digital I/O, 192 I/O, 888|24 I/O,
882|20 I/O, 1622 I/O, 24-Bit ADAT Bridge I/O, AudioSuite,
Avid, Avid DNA, Avid Mojo, Avid Unity, Avid Unity ISIS,
Avid Xpress, AVoption, Axiom, Beat Detective,
Bomb Factory, Bruno, C|24, Command|8, Control|24,
D-Command, D-Control, D-Fi, D-fx, D-Show, D-Verb, DAE,
Digi 002, DigiBase, DigiDelivery, Digidesign,
Digidesign Audio Engine, Digidesign Intelligent Noise
Reduction, Digidesign TDM Bus, DigiDrive, DigiRack,
DigiTest, DigiTranslator, DINR, DV Toolkit, EditPack, Eleven,
EUCON, HD Core, HD I/O, HD MADI, HD OMNI,
HD Process, Hybrid, Impact, Interplay, LoFi, M-Audio,
MachineControl, Maxim, Mbox, MediaComposer, MIDI I/O,
MIX, MultiShell, Nitris, OMF, OMF Interchange, PRE,
ProControl, Pro Tools, Pro Tools|HD, Pro Tools LE,
Pro Tools M-Powered, Pro Tools MP, QuickPunch, Recti-Fi,
Reel Tape, Reso, Reverb One, ReVibe, RTAS, Sibelius,
Smack!, SoundReplacer, Sound Designer II, Strike, Structure,
SYNC HD, SYNC I/O, Synchronic, TL Aggro, TL AutoPan,
TL Drum Rehab, TL Everyphase, TL Fauxlder, TL In Tune,
TL MasterMeter, TL Metro, TL Space, TL Utilities, Transfuser,
Trillium Lane Labs, Vari-Fi, Velvet, X-Form, Xpand! and
XMON are trademarks or registered trademarks of Avid
Technology, Inc. All other trademarks are the property of their
respective owners.
Documentation Feedback
At Avid, we are always looking for ways to improve our
documentation. If you have comments, corrections, or
suggestions regarding our documentation, email us at
techpubs@avid.com.
Contents
Contents iii
Chapter 6. HD Native Thunderbolt について. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
HD Native Thunderbolt の
パッケージ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
HD Native Thunderbolt システム . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
登録 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
システム要件と互換性 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
本ガイドで使用する表記法 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
www.avid.com について . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
The names of Commands, Options, and Settings Training and Education Study on your own using
that appear on-screen are in a different font. courses available online or find out how you can
learn in a classroom setting at a certified Pro Tools
The following symbols are used to highlight training center.
important information:
Products and Developers Learn about Avid prod-
User Tips are helpful hints for getting the ucts; download demo software or learn about our
most from your Pro Tools system. Development Partners and their plug-ins, applica-
tions, and hardware.
Important Notices include information that News and Events Get the latest news from Avid or
could affect your data or the performance of sign up for a Pro Tools demo.
your system.
HD Native Thunderbolt
HD Native Thunderbolt supports up to 64 channels of I/O for direct-to-disk recording and playback, and
supports up to 24-bit and up to 192 kHz audio streams. Additionally, the on-board FPGA (field-program-
mable gate array) provides dedicated signal routing for headphone monitoring.
Power LED Green Indicates that the audio output for head-
phone monitoring is active.
The LED lights red when the unit is connected to
your computer and the computer is powered on. Purple Indicates that the MCU (microcontroller
The LED changes color to indicate the status of unit) is being reset.
Headphone monitoring and whether or not a firm-
ware update is in progress. Headphone Jack
Red Indicates that the unit is connected and pow- HD Native Thunderbolt provides a single stereo
ered on, and that the audio output for headphone 1/4-inch headphone jack on the front panel. The
monitoring is muted. output to the headphone jack mirrors channel
outputs 1 and 2 on your primary Avid HD audio
interface.
HD Native Thunderbolt lets you adjust the head- If the Volume control stops working, reset the
phone volume using the Volume/Mute knob on MCU. Note that resetting the MCU may take a few
the front panel. Turn the knob counter-clockwise seconds.
to lower and clockwise to raise the headphone vol-
ume. You can also press the Volume/Mute knob to To reset the MCU:
mute and unmute headphone monitoring, as well 1 Make sure the Thunderbolt cable connecting
as to reset the MCU (microcontroller unit). HD Native Thunderbolt to your computer is dis-
connected, and that the computer is powered on.
Muting and Unmuting Headphone Monitoring
2 Press and hold the Volume/Mute knob.
To mute headphone monitoring:
3 Connect the Thunderbolt cable. HD Native
Press and momentarily hold the Volume/Mute
Thunderbolt powers on with the LED showing
knob so the Power LED turns red.
purple.
To unmute headphone monitoring: 4 Release the Volume/Mute knob.
Press and momentarily hold the Volume/Mute 5 Disconnect and reconnect the Thunderbolt
knob so the Power LED turns green. cable to power cycle the unit. HD Native Thun-
derbolt powers on with the LED showing red.
Use the Thunderbolt port to connect HD Native HD Native Thunderbolt is powered over the Thun-
Thunderbolt directly to any available Thunderbolt derbolt bus. However, you can also connect a stan-
port on your Avid-qualified computer using the dard AC adapter (sold separately) to power the unit
included Thunderbolt cable. Be sure that your independently.
computer is powered down when making the con-
nection. Once you have made the connection, you
can then power on your computer and use HD
Native Thunderbolt.
DigiLink Mini Cables
Use DigiLink Mini cables to connect HD I/O,
DigiLink Mini Ports HD OMNI, and HD MADI audio interfaces to HD
Native Thunderbolt. There are five different
HD Native Thunderbolt includes two DigiLink
lengths of DigiLink Mini cables:
Mini ports for connecting to Avid HD audio inter-
faces. Each port provides up to 32 channels of au- • 18” (0.46m) (included with HD I/O, HD OMNI,
dio input and output. and HD MADI audio interfaces)
• 12’ (3.6m) (one included with HD Native
DigiSerial Port Thunderbolt)
You can connect a SYNC peripheral to the DigiSe- • 25’ (7.62m) (sold separately)
rial port on HD Native Thunderbolt. This connec-
• 50’ (15.25m), the maximum length supported
tor is an 8-pin mini-DIN.
for 176.4 kHz and 192 kHz sessions (sold
The DigiSerial port on HD Native Thunderbolt separately)
does not support MachineControl connections. • 100’ (30.5m), the maximum length supported by
88.2 kHz and 96 kHz sessions (sold separately)
FPGA Reset Switch
• Flexible monitoring with fold-down from all ste- • Up to 16 channels of 24-bit D/A and A/D con-
reo and surround formats (up to 7.1 verters for superior analog input and output at
surround) sample rates of 44.1 kHz, 48 kHz, 88.2 kHz,
96 kHz, 176.4 kHz, and 192 kHz with Analog In
• Input mixer for low latency direct monitoring of
and Analog Out HD I/O cards
a variety of incoming signals (configured in the
Pro Tools Hardware Setup) • Soft Clip and Curv limiting circuits to protect
against clipping on analog input
Synchronization
Digital I/O
• Loop Sync input and output for connecting addi-
tional Avid HD audio interfaces and peripherals • Up to 16 channels of 24-bit digital I/O, using
AES/EBU, TDIF DB-25, or Optical at sample
• External Clock input and output for synchroniz-
rates of 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz,
ing HD OMNI with external Word Clock
176.4 kHz, and 192 kHz with a Digital HD I/O
devices
card
• Real-time sample rate conversion on digital in-
HD I/O Audio Interface puts with a Digital I/O card (up to 16 channels of
HD I/O is a multichannel digital audio interface AES/EBU, Optical, or TDIF)
designed for use with HD Native systems. HD I/O • Support for S/MUX Optical for sample rates of
features extremely high quality 24-bit analog-to- 88.2 kHz and higher
digital (A/D) and digital-to-analog (D/A) convert-
ers, and supports sample rates of up to 192 kHz. • Support for 2 channels of S/PDIF Optical
(enclosed) with sample rates of up to 96 kHz
HD I/O comes in three standard configurations: • 2 channels of AES/EBU I/O (enclosed) with
• 8 x 8 x 8 (8 analog in, 8 analog out, and support for sample rates up to 192 kHz
8 digital in and out) • 2 channels of 24-bit-capable S/PDIF I/O
• 16 x 16 analog in and out (enclosed) with support for sample rates up to
• 16 x 16 digital in and out 192 kHz
See the HD I/O Guide for more information. • External Clock input and output for synchroniz-
ing HD I/O with external Word Clock devices
4 Start your computer. You can also get a full 64 channels of I/O with
HD MADI connected to HD Native Thunderbolt
HD Native Thunderbolt is powered by the Thun- using 2 DigiLink Mini cables. However,
derbolt bus, so no additional power is required. HD MADI will be the only audio interface in the
However, in certain situations, you may want to system.
power HD Native Thunderbolt separately. If this is
the case, you can connect a DC power adapter Refer to the HD OMNI Guide, HD I/O Guide, or
(sold separately) to HD Native Thunderbolt. HD MADI Guide for specific details regarding:
Press the volume/mute knob to toggle the Front and back panel connectors and
mute status of the headphone output. indicators
Installation of optional expansion I/O cards
(HD I/O only)
• Connect the Primary Port of the secondary inter- To make Loop Sync connections:
face to the Expansion Port of the primary inter-
1 Connect the Loop Sync Out of each interface to
face with an additional DigiLink Mini cable.
the Loop Sync In of the next interface with the
• Connect the Primary Port of the secondary inter- BNC cables included in your I/O packaging.
face to DigiLink Mini Port 2 on HD Native
Thunderbolt. 2 Connect the Loop Sync Out of the last interface
18-inch DigiLink
HD I/O Mini cable
Loop Sync
HD I/O cables
HD I/O
The Prefs button opens the Avid CoreAudio Man- This option is grayed out for systems using
ager Preferences dialog. There are several options HD Native Thunderbolt. When using 003,
available configuring the Manager application. 003 Rack, 003 Rack+, Digi 002, or Digi 002 Rack,
When finished setting these options, click OK to enable this option to mirror the main outputs
close the Avid CoreAudio Manager Preferences through the digital outputs that are selected in the
window. Hardware Setup dialog.
Connect Button
Low Latency Monitoring is not available with To configure Low Latency Monitoring in the I/O
Core Audio–compatible software. Setup:
1 From the Output Path selector, assign each track 2 Click the Output tab.
to the selected Low Latency Monitoring Path 3 Enable the Low Latency Monitoring option.
(as set in the I/O Setup Output page). Only
tracks assigned to these outputs use Low La- 4 From the Low Latency Monitoring pop-up menu,
tency Monitoring. select the Output path you want to use for Low
Latency Monitoring.
2 Record enable audio tracks by clicking their Re-
cord Enable buttons.
3 Select Options > Low Latency Monitoring.
の
• HD I/O
HD Native Thunderbolt
パッケージ • HD MADI
システム要件と互換性 画面に表示されるコマンド、オプション、設定の名前
は、フォントが異なります。
H D N a t i v e T h u n d e r b o l t ハードウェアは、
Pro Tools HD ソフトウェアまたはサードパー 以下の記号は、重要な情報を示すのに使用されます。
ティー製 CoreAudio 互換ソフトウェアを実行す Pro Tools システムを活用するために役立つ
る、Avid の要件を満たすコンピューターで使用で アドバイス。
きます。
Avid は、動作確認が行われたハードウェアとソフ
トウェアに対してのみ互換性を保証し、サポート データやシステムの処理能力に作用する重
を提供します。 要な情報。
完全なシステム要件および要件を満たしたコン 便利なキーボードやマウスのショートカット。
ピューター、オペレーティング・システム、ハー
ド・ドライブ、サードパーティー製機器のリスト
については以下のサイトをご覧ください。 このガイドまたは他の Pro Tools ガイドの関
www.avid.com/compatibility 連セクション。
ご使用の HD Native Thunderbolt ハードウェア
は、Avid DigiTest を使用してテストすることが
できます。詳しくは、Avid DigiTest Guide.pdf を
ご参照ください(ダウンロードして、または
Pro Tools インストールの付属文書としてご覧い
ただけます)。
HD Native Thunderbolt
は、ダイレクト・ディスク・レコーディングとプレイバックに最大 64 チャンネ
HD Native Thunderbolt
ルの を提供し、最高 ビット /192kHz のオーディオ・ストリームに対応しています。さらに、内蔵
I/O 24
により、ヘッドフォン・モニタリング専用のシグナル・ルーティングを提供します。
FPGA
赤 本機が接続されて電源が入っており、ヘッド
を つ搭載しています。ヘッドフォン・ジャック
1
•
HD MADI について、詳しくは『 HD MADI ターフェイスや周辺機器(HD I/O 、HD OMNI、
ガイド』をご参照ください。 SYNC HD など)と同期させる BNC Loop Sync
I/O
Loop Sync
HD I/O ケーブル
HD I/O
Pro Tools ソフトウェアをインストール
しオーソライズする
ハードウェア
Pro Tools HD Native Thunderbolt
をコンピューターに接続できたら、Pro Tools HD
ソフトウェアをインストールしてオーソライズし
ます。
インストールとオーソライズについて詳し
くは、Pro Tools ソフトウェア・パッケージ
に付属の『Pro Tools インストール・ガイ
ド』をご参照ください。
2 以下のオプションからご使用のシステムのバッ
ファー・サイズを選択します。
• [ Maximum/Large ]バッファー・サイズ
または
• [ Minimum/Small ]バッファー・サイズ
第 4 章: CoreAudio を設定する 41
Apple の Audio MIDI 設定 5 左の[オーディオ装置]リストから[HD Native
Apple の[Audio MIDI 設定]を設定するには: ] を選択します。
Thunderbolt
4 [オーディオ装置]ウィンドウから[出力]タブ
をクリックします。
Proposition 65 Warning
Environmental Compliance
This product contains chemicals, including
Disposal of Waste Equipment by Users lead, known to the State of California to
in the European Union
cause cancer and birth defects or other
reproductive harm. Wash hands after
handling.
Perchlorate Notice
This product may contain a lithium coin battery. The State of
California requires the following disclosure statement:
“Perchlorate Material – special handling may apply, See
This symbol on the product or its packaging indicates that this www.dtsc.ca.gov/hazardouswaste/perchlorate.”
product must not be disposed of with other waste. Instead, it
is your responsibility to dispose of your waste equipment by
handing it over to a designated collection point for the
Recycling Notice
recycling of waste electrical and electronic equipment. The
separate collection and recycling of your waste equipment at
the time of disposal will help conserve natural res+ources and
ensure that it is recycled in a manner that protects human
health and the environment. For more information about
where you can drop off your waste equipment for recycling,
please contact your local city recycling office or the dealer
from whom you purchased the product.
12) For products that are not rack-mountable: Use only with a
cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the equipment. When a cart is
used, use caution when moving the cart/equipment
combination to avoid injury from tip-over.