Beruflich Dokumente
Kultur Dokumente
Redundant FBM228s, shown above mounted on the same baseplate with fault-tolerant FCP270 Field
Control Processors, provide a redundant interface to FOUNDATION™ fieldbus H1 devices for I/A Series®
control stations such as the FCP270 or the ZCP270 Z-Form Control Processors.
Can be installed as a redundant pair providing H1 bus provides all the benefits of the traditional
maximum uptime, with fully redundant 4 to 20 mA standard, while providing greater data
communications between the FBM228 and fault- access to both control and system health
tolerant control processors. information.
Integrates H1 device data into an I/A Series FOUNDATION fieldbus (FF) enables you to take full
format for consistent operator display of alarms, advantage of intelligent field devices, resulting in
trends, and operator displays that are access to device maintenance information, reduced
independent of the protocol/communication bus equipment and wiring costs, and a wider selection of
used to bring them into the system. suppliers due to interoperability.
Compatible with a variety of power conditioning The FBM228 connects the H1 field devices to the
devices from Invensys and third-party versatile and robust I/A Series control system, where
manufacturers. control resources include new FOUNDATION fieldbus
specific blocks (FF blocks): AI, AO, DI, and DO and
Bus powering is a function of the type of field
an enhanced set of Distributed Control Interface
termination assembly. The typical non-intrinsic
(DCI) blocks.
safety termination assembly contains power
converters that provide from 300 mA to The FBM228 enables the control station to access
1 A of conditioned power to each H1 Link almost any block parameter in any H1 device.
(see “Power Options” on page 3. With FF blocks, parameters in the H1 device are
dynamically updated in the control station memory
Provides a Link Active Scheduler (LAS) for each
and are connectable to all other blocks in the station,
H1 Link.
thus allowing easy construction of control loops that
The FBM automatically detects and schedules all contain H1 function blocks and control station
devices on each H1 Link, providing faster start- blocks.
up, commissioning, and device replacement.
The enhanced DCI block set enables the control
The FOUNDATION fieldbus links conform station to access block parameters in an H1 device.
to ANSI/ISA S-50, IEC 61158, and The parameters specified by offset.subindex are the
CENELEC EN 50170. parameters in resource, transducer, and function
blocks. These DCI blocks can be used, for example,
The FBMs are suitable for installation in Class 1,
to source device diagnostic information for the
Division 2, and Zone 2 locations.
development of maintenance and alarm strategies.
OVERVIEW The blocks include:
The FOUNDATION fieldbus Redundant Interface BIN for binary input
Module (FBM228) provides a reliable, high-capacity IIN for integer values
interface between FOUNDATION fieldbus devices and RIN for real input
the I/A Series system. The FBM228, which can be ROUT for real output
used in single or redundant configurations, supports PAKIN for bit-enumerated parameters
four H1 Links for a maximum of 64 fieldbus devices. STRIN for string data.
The H1 fieldbus is a bi-directional, all digital
communication bus designed for the integration of
process measurement and control devices. The
PSS 21H-2Z28 B4
Page 3
When the control station is a ZCP270, the The galvanically isolating HD2-FBPS-1.500.
FBM228s are installed in a DIN Rail Mounted FBM
Figure 2 illustrates a typical generic setup usable for
system consisting of a Fieldbus Communications
any third-party power conditioners in either
Module 100 (FCM100), the FBM228, and other FBM
redundant or non-redundant configurations. A
types.
passive termination assembly (p/n P0922VC)
The subsystem is connected to the ZCP270 via provides a connection between the baseplate and
a 100 Mbps Ethernet network. For additional the power conditioning modules. The third party
information on this communication network, refer to modules are then connected using standard H1
the DIN Rail Mounted Subsystem Overview (PSS practices with respect to power conditioning,
21H-2W1 B3.) distances, bus termination, and safety certifications.
Example power conditioning options include:
POWER OPTIONS
Pepperl+Fuchs® KLD2-PC-1.1 IEC
Power to the H1 bus is always a function of the
selected power conditioners. To allow customers’ Relcom® FPS-1 redundant power system with
preferences in cabinet design and hazardous area terminators
configurations, the I/A Series FOUNDATION fieldbus is
Fieldbus Intrinsically Safe Concept (FISCO) power
designed to let customers select power conditioners
conditioners from Pepperl+Fuchs and MTL
from the many different solutions available on the
PSS 21H-2Z28 B4
Page 4
Module Fieldbus
(to next baseplate)
Fieldbus Modules
Operational Status
®
Operational Status
®
Operational Status
®
Power Conditioners
FBM201 FBM201 FBM201 FBM201
Channel Isolated Channel Isolated Channel Isolated
Channel Isolated
8 input, 0-20mA 8 input, 0-20mA 8 input, 0-20mA
8 input, 0-20mA
P0914SQ P0914SQ P0914SQ
P0914SQ
® ® ®
®
FBM228s
FOUNDATION Fieldbus
(Typical Topology)
Splitters/
Combiners FCP270
FCP270 Baseplate
Up to 16 Field Devices
per H1 Link
Terminator
FCP270 Baseplate
®
®
Baseplate and
Operational Status
Operational Status
Cabling provide
Redundant 2 Mbps
FBM201
Channel Isolated
8 input, 0-20mA
P0914SQ
®
FBM201
Channel Isolated
8 input, 0-20mA
P0914SQ
®
Module Fieldbus
FCM I dentificati on
Left Module Right Module
®
P0914ZM User Defined
Passive Termination
Assembly (P0922VC)
Splitters/ FCP270
Combiners
To Redundant
Bulk Power Third-party
Supplies Redundant Power
Conditioners
FOUNDATION Fieldbus
(Typical Topology)
Up to 16 Field Devices
per H1 Link
Terminator
Operating Vibration
TEMPERATURE 7.5 m/S2 (0.75 g) from 5 to 500 Hz
−20 to +70°C (−4 to +158°F) Storage
RELATIVE HUMIDITY TEMPERATURE
5 to 95% (non-condensing) −40 to +70°C (−40 to +158°F)
ALTITUDE RELATIVE HUMIDITY
−300 to +3,000 m (−1,000 to +10,000 ft) 5 to 95% (non-condensing)
Contamination ALTITUDE
Class G3 (Harsh) as defined in ISA Standard, S71.04. −300 to +12,000 m (−1,000 to +40,000 ft)
Pollution degree 2 as defined in IEC 664-1.
(1) The environmental limits of this module may be enhanced by the type of enclosure containing the module. Refer to the applicable
Product Specification Sheet (PSS) which describes the specific type of enclosure that is to be used.
P H Y S I C A L S P E C I F I C AT I O N S
33 Commercial Street Invensys, Foxboro, and I/A Series are trademarks of Invensys plc, its
Foxboro, MA 02035-2099 subsidiaries, and affiliates.
United States of America All other brand names may be trademarks of their respective owners.
www.foxboro.com
Inside U.S.: 1-866-746-6477
Outside U.S.: 1-508-549-2424 Copyright 2004-2007 Invensys Systems, Inc.
or contact your local Foxboro All rights reserved
representative.
Facsimile: 1-508-549-4999 MB 21A Printed in U.S.A. 0807