Beruflich Dokumente
Kultur Dokumente
SERVICE MANUAL
CONTENTS
REVISED PAGE LIST ............................................................ 2-1
SPECIFICATIONS .................................................................. 3-1
PANEL LAYOUT ..................................................................... 3-2
DIMENSIONS ......................................................................... 3-3
CONNECTOR CIRCUIT DIAGRAM .......................................... 4
BLOCK DIAGRAM ..................................................................... 6
DISASSEMBLY PROCEDURE ................................................. 7
LSI PIN DESCRIPTION ........................................................... 11
IC BLOCK DIAGRAM .............................................................. 14
CIRCUIT BOARDS .................................................................. 16
INSPECTION ...................................................................... 21/23
TEST PROGRAM ............................................................... 26/31
ERROR MESSAGES ............................................................... 42
PARTS LIST
CIRCUIT DIAGRAM
PA 011505
HAMAMATSU, JAPAN 1
Copyright (c) Yamaha Corporation. All rights reserved. PDF-K- K ’01.03
****
AI8
SPECIFICATIONS 3-1
PANEL LAYOUT 3-2
DIMENSIONS 3-3
BLOCK DIAGRAM 6
DISASSEMBLY PROCEDURE 7,9
IC BLOCK DIAGRAM 14
CIRCUIT BOARDS 16~20
AC, IPC3, DR, PSB, LED1 16
DC, MB1 19
IFC2 20
INSPECTION 21~22
TEST PROGRAM 23~27
ERROR MESSAGES 42
<PARTS LIST>
ITEM PAGE
OVERALL ASSEMBLY 2, 3, 4
MOTHER ASSEMBLY 6
<CIRCUIT DIAGRAM>
ITEM PAGE
003 4
003 10
004 11
005 12
006 13
007 14
008 15
2-1
AI8
IMPORTANT NOTICE
This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that
basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and understood by
the users, and have therefore not been restated.
WARNING: Failure to follow appropriate service and safety procedures when servicing this product may result in personal
injury, destruction of expensive components and failure of the product to perform as specified. For these
reasons, we advise all Yamaha product owners that all service required should be performed by an authorized
Yamaha Retailer or the appointed service representative.
IMPORTANT: This presentation or sale of this manual to any individual or firm does not constitute authorization, certification,
recognition of any applicable technical capabilities, or establish a principal-agent relationship of any form.
The data provided is belived to be accurate and applicable to the unit(s) indicated on the cover. The research engineering, and
service departments of Yamaha are continually striving to improve Yamaha products. Modifications are, therefore, inevitable and
changes in specification are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist,
please contact the distributor's Service Division.
WARNING: Static discharges can destroy expensive components. Discharge any static electricity your body may have
accumulated by grounding yourself to the ground bus in the unit (heavy gauge black wires connect to this bus).
IMPORTANT: Turn the unit OFF during disassembly and parts replacement. Recheck all work before you apply power to the
unit.
WARNING
Components having special characteristics are marked and must be replaced with parts having specification equal to those
originally installed.
2-2
AI8
SPECIFICATIONS
Sampling frequency (external sync) 39.69 kHz – 50.88 kHz
USA and Canada: 120 V, 60 Hz
Power supply
Others: 230 V, 50 Hz
Power consumption 120 W
Dimensions (W x H x D) 480 mm x 141.5 mm x 466.8 mm
Weight 15.4 kg
Operating temperature 10 – 35 ˚C
Power cable length 2.1 m
Cooling fan speed always fixed
Accessories Connection cable (68-pin, D-sub, half-pitch) x 1, Length: 3 m
Digital I/Os
I/O connectors Level Type
OUTPUT A, B, C RS-422 D-sub, half-pitch, 68-pin connector (female)
WORD CLOCK IN TTL/75 Ω (ON/OFF) BNC Connector
WORD CLOCK OUT TTL/75 Ω BNC Connector
Slots
Card Input
LMY2-ML Channel 1A or 1B, 2A or 2B
LMY4-AD Channel 1 – 4
3-1
AI8
PANEL LAYOUT
PHANTOM MASTER
1 2 3 4 5 6 7 8
ON
UNIT NO.
+48V 2
PHANTOM MASTER
OFF
ON
+48V
OFF
POWER
ON/ OFF
POWER
ANALOG INPUT BOX
ON/ OFF
Rear Panel
5
CONTROL OUTPUT
PORT
A
4 B
C B A
C
CONTROL
PORT
A
C
OUTPUT
B A
WORD
CLOCK
B
C
WORD
CLOCK
IN
OFF
ON 75
OUT
6 IN
OFF
ON 75
7
OUT
3-2
AI8
DIMENSIONS
430
466.8
455
480
1 2 3 4 5 6 7 8
UNIT NO.
132 (3U)
PHANTOM MASTER
141.5
ON
+48V
OFF
POWER
ON/ OFF
9.5
3-3
AI8
FG **
[INPUT
CN702 CN701 UNIT ID]
3P 4P
5P CN127 LED1
4P CN126
6P CN103
3P
CN802 5P
CN002 6P CN124
CN800 CN101 4P
CN300 2P
2P CN001
4P 4P CN123
CN301 4P
CN302 2P
CN303 4P
6P CN122
CN200 12P
4P CN121
CN400 4P
CN102 20P 20P CN120
DC
CN101 30P 30P CN119
[A]
[CONTROL PORT] [B] CN200 5P 5P CN510
CN109
[C]
100P
CN509 14P
[ON]
[75 ]
[OFF]
UNC
CN108
[IN] CN508 8P 8P CN117
100P
[8]
[WORD CLOCK] CN300 5P 5P CN511
[OUT]
IPC3
CN107
100P
IPC1
100P
IPC1
100P
IPC1
100P
SLOT NO.
CN512 6P 8P CN118
IFC2 MB1
KEC-92522-2
4
AI8
Circuit Board CN No. Pin No. Circuit Board CN No. Pin No.
DC CN100 1 MB1 CN122 4
2 3
3 MB1 CN124 4
4 3
5 MB1 CN127 5
6 IFC2 CN103 1
7 2
8 MB1 CN122 2
9 1
10 MB1 CN124 2
11 1
12 MB1 CN127 3
13 IFC2 CN103 3
14 4
DC CN101 1 MB1 CN127 4
2 IFC2 CN103 5
3 6
DC CN200 1 MB1 CN121 4
2 3
3 MB1 CN123 4
4 3
5 MB1 CN125 4
6 3
7 MB1 CN121 1
8 MB1 CN123 1
9 MB1 CN125 1
DC CN300 1 DR CN800 1
2 2
DC CN301 1 MB1 CN122 6
2 MB1 CN124 6
DC CN302 1 MB1 CN127 2
2 1
DC CN303 1 MB1 CN122 5
2 MB1 CN124 2
DC CN400 1 LED1 CN101 1
2 2
3 3
4 4
IFC2 CN509 1 LED1 CN100 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 9
10 10
11 11
12 12
13 13
14 14
MB1 CN126 1 LED1 CN101 7
3 LED1 CN101 6
4 5
KEC-92522-3
5
6
AI8
SLOT NO.
BLOCK DIAGRAM
IC601
/CS1 I11
/CON1 [1] I12
DOA
DSP5 [OUTPUT]
IC401
WCIA
/CS2 I21 DIR2 Driver
/CON2 [2] I22 [A]
IC307 ID I/O Receiver
44.1K
DIR2
48K WCO
/CS3 I31 IPC1
/CON3 [3] I32
DOB
LOCK
IC402
/CS4 I41 WC SEL & SYNC DETECTOR WC
WCIB
/CON4 [4] I42 DIR2 Driver
[B]
ID I/O Receiver
/CS5 I51
WCO
/CON5 [5] I52 Decoder IPC1
Register
/CS6 DOC
I61 IC202 FPGA IC404
/CON6 [6] I62
WCIC
DIR2 Driver
IC301
[C]
ID I/O Receiver
/CS7 I71 DIR2 2 IC302
/CON7 [7] I72
WCO
MASTER
CLOCK
IPC1
/CS8 I81 IC405
/CON8 [8] I82 WCID [IN]
DIR2
[WORD CLOCK]
WCO
[ON] [OUT]
[OFF] [75 ]
MB1 48V
IFC2
[A]
[B]
[C]
[CONTROL PORT]
IPC3
[ON] 48V
Data Bus
Register [PHANTOM MASTER]
CPU [+48V]
Address Bus
Decoder
[INPUT UNIT ID]
IC101 [OFF]
LED1
RAM FLASH
UNC IC203 IC201
KEC-92520 1
AI8
DISASSEMBLY PROCEDURE
1. UNC Card Assembly
1-1 Remove the four (4) screws marked [470]. The UNC card
assembly can them be removed. (Fig. 1)
[450]
[400]
[452]
Mount bracket
<Left Side View>
Mount bracket [400] [500] x 32 [470] Mount bracket
[450]
[452]
Mount bracket
Fig. 1
7
AI8
[100]
PSB
Top panel
Fig. 2
6. Mother Assembly
6-1 Remove the UNC card assembly. (See Procedure 1.)
6-2 Remove the front panel assembly. (See Procedure 2.)
6-3 Remove the top panel. (See Procedure 4-3.)
6-4 Remove the seven (7) screws marked [280]. The mother
assembly can then be removed. (Fig. 3)
[280]
Mother assembly
[180]
[450]
IFC2
[200] [452]
[30] <Right Side View>
[70] Mount bracket Side panel assembly
[450]
[452]
<Rear View> [260]
[50] [260]
MB1
[30]: Bind Head Tapping Screw-B 3.0x6 MFZN2BL (EP600230) [200]: Bind Head Tapping Screw-B A4.0x8 MFZN2BL (VC688800)
[50]: Bind Head Tapping Screw-B 3.0x6 MFZN2BL (EP600230) [260]: Bind Head Tapping Screw-B A4.0x8 MFZN2BL (VC688800)
[70]: Bind Head Tapping Screw-B 3.0x6 MFZN2BL (EP600230) [450]: Oval Head Screw 4.0x8 MFZN2BL (VS153600)
[452]: Oval Head Screw B4.0x10 MFZN2BL (V6221000)
Fig. 4 Fig. 5
9
AI8
10. AC Assembly
10-1 Remove the side panel assembly. (See Procedure 9.)
10-2 Remove the three (3) screws marked [90]. The AC
assembly can then be removed. (Fig. 6)
11. DC Assembly
11-1 Remove the side panel assembly. (See Procedure 9.)
11-2 Remove the four (4) screws marked [60]. The DC
assembly can then be removed. (Fig. 6)
[D60]
DC assembly AC assembly
TR holder
DC
BR holder
[60] [90]
[D90]
[D80]
[60]: Bind Head Screw A4.0x6 MFZN2BL (EG340290) [D60]: Pan Head Screw SP4.0x8 MFZN2Y (EL200020)
[90]: Bind Head Tapping Screw-B A4.0x8 MFZN2BL (VC688800) [D80]: Pan Head Screw SP4.0x8 MFZN2Y (EL200020)
[D90]: Bind Head Tapping Screw-B 3.0x6 MFZN2BL (EP600230)
Fig. 6 Fig. 7
10
AI8
11
AI8
12
AI8
13
AI8
IC BLOCK DIAGRAM
1A 1 14 VDD
1A 1 14 VDD 1A 1 14 VDD
1B 2 13 4B
1Y 2 13 1Y 2 13
6A 6A
1Y 3 12 4A
2A 3 12 2A 3 12
6Y 6Y
4 4
2A 4 11 4Y
2Y 11 5A 2Y 11 5A
5 10 5 10
2B 5 10 3B
3A 5Y 3A 5Y
6 9 6 9 2Y 6 9 3A
3Y 4A 3Y 4A
3 D 12 A
1CK CK 2D 2 19
Select B 2 B Y0 15 YO A1 G
1PR 4 PR 11 18
CK 2CK 3 C Y1 14 A2 3 B1
C Y1
1Q 5 Q 10 17
PR 2PR G2A 4 G2A Y2 13 Y2 A3 4
B2
Output
6 Q 9 Enable 16
1Q Q 2Q 5 G2B Y3 12 A4 5 B3
G2B Y3
GND 7 Q 8 2Q 15
6 G1 Y4 11 A5 6 B4
G1 Y4
Output A6 7 14
Y7 7 Y7 Y5 10 Y5 B5
INPUTS OUTPUTS Y6
PR CLR CLK D Q Q A7 8 13
GND 8 9 Y6 B6
L H X X H L
A8 9 12 B7
H L X X L H
L L X X H H 11
GND 10 B8
H H f H H L
H H f L L H
H H L X QO QO
1A 1 16 Vcc
1Y 2 15 4A
INPUT A 1 16 Vcc
1 20 1Z 3 14 4Y -
CLEAR VCC
INPUT A 2 + 15
2 19 ENABLE G 4 13 4Z
- INPUT B
1Q Q Q 8Q
CL CL
+
3 D CK CK D 18 2Z 5 12
OUTPUT A 3 14 INPUT B
1D 8D ENABLE G
4 17 2Y 6 11 ENABLE 4 13 OUTPUT B
2D D CK CK D 7D 3Z
CL CL
2Q 5 Q Q 16 7Q 2A 7 10
OUTPUT C 5 12 ENABLE
3Y
3Q 6 15 6Q 3A INPUT C 6
+ 11 OUTPUT D
Q Q GND 8 9
CL CL
7 D CK CK D 14 INPUT C 7 - 10
3D 6D + INPUT D
INPUT ENABLES OUTPUTS
-
4D 8 D CK CK D 13 5D A G G Y Z GND 8 9 INPUT D
CL CL H H X H L
4Q 9 Q Q 12 5Q L H X L H
10 11
H X L H L
GND CLOCK
L X L L H
X L H Z Z
H= high level X= irrelevant
L= low level Z= high impedance (off)
14
AI8
1A 1 16 Vcc 1A 1 16 Vcc
1B 2 15 1S 1B 2 15 2F
2R 3 14 1R 1C 3 14 2E
2S 4 13 1Y 1D 4 13 2D
2A 5 12 3A 1E 5 12 2C
2B 6 11 3S 1F 6 11 2B
2Y 7 10 3R 1Y 7 10 2A
GND 8 9 3Y GND 8 9 2Y
Note: See parts list for details of circuit board component parts.
15
AI8
CIRCUIT BOARDS
AC Circuit Board DR Circuit Board
to FAN
AC Cord
to DC-CN300
Component side
toAC-CN701
IPC3 Circuit Board
A
Component side
INPUT PORT
to IFC2-CN510
CONTROL
B
IN
to IFC2-CN509
ON
CLOCK
WORD
75
to DC-CN400
OFF
OUT
Pattern side
Component side
3NA-V412870 2
18
19
AI8
Component side
to IFC2-CN512
to IFC2-CN101
MB1 Circuit Board
to IFC2-CN102
to IFC2-CN501 to IFC2-CN502 to IFC2-CN503 to IFC2-CN504 to IFC2-CN505 to IFC2-CN506 to IFC2-CN507 to IFC2-CN508
to MB1-CN127
to LED-CN101 IFC2-CN103
Component side
DC Circuit Board
3
DC: 3NA-V412850
MB1: 3NA-V412880
Power transformer to MB1-CN122 to MB1-CN127 to MB1-CN121 to MB1-CN122, CN124,
CN124 to DR-CN800 Power transformer CN123 CN127
CN125 IFC2-CN103
3NA-V412890 3
Pattern side
to IPC1 3/3-CN101 to IPC1 2/3-CN101
to MB1-CN119 to DC-CN100 to IPC1 3/3-CN102 to IPC1 2/3-CN102 to IPC1 1/3-CN102
to LED1-CN100 CN101
to MB1-CN118
Component side
to IPC1 1/3-CN101
IFC2 Circuit Board
to IPC1 1/3-CN103
to MB1-CN117 to MB1-CN116 to MB1-CN115 to MB1-CN114 to MB1 to MB1-CN112 to IPC1 3/3 to IPC1 2/3 to MB1-CN110
-CN113 -CN103 -CN104
to MB1-CN120 to IPC3 to IPC3 to IPC1 3/3 to MB1-CN111 to IPC1 2/3 to IPC1 1/3-CN104
AI8
20
AI8
INSPECTION
1. Range of Applicability
These specifications apply to the AI8, AI8-ML8, AI8-AD8, and AI8-ML4AD4.
2. Preparations
2-1. Conditions
For details on the connection method, refer to the Test Program Specifications KES-92652.
Unless otherwise specified, the conditions are as follows.
· Set the PHANTOM MASTER switch to On.
· Set WORD CLOCK IN 75 Ω to ON.
· Set the CONTROL INPUT PORT to A.
3. Inspection
3-1. Inspection with Test Program
· Inspect based on the Test Program Specifications KES-92652.
3-4. Sound
· The connections are as in the diagram below.
Connection diagram
LMY2-ML AI8 AO8 LMY4-DA
or 68-pin cable
LMY4-AD
OUTPUT A INPUT A
x8 x8
LMY2-ML
or BNC
LMY4-AD LMY4-DA
Function Generator
OMNI OUT INPUT
01V
ST OUT Power speaker
· Set the AI8 and AO8 sheet UNC DIP switch as below. DIP Switch 8 is not used.
DIP SW
1 2 3 4 5 6 7
AI8 OFF ON OFF OFF ON ON ON
AO8 OFF OFF OFF ON OFF OFF OFF
· For 01V, OSC1kHz is output from OMNI OUT and the signal input to INPUT is assigned to ST OUT.
· For AI8, insert the inspection LMY4-AD cards in Slot 1-8.
· For AI8-ML8, insert the shipping LMY2-ML cards in Slot 1-8.
· For AI8-AD8, insert the shipping LMY4-AD cards in Slot 1-8.
· For AI8-ML4AD4, insert the shipping LMY2-ML cards in Slot 1-4 and the shipping LMY4-AD cards in Slot 5-8.
21
AI8
4. Factory Settings
· Switch all the sheet UNC DIP switch settings On.
· Front panel
PHANTOM MASTER: OFF
· Rear panel
WORD CLOCK IN 75 Ω: On
CONTROL INPUT PORT: A
22
AI8
TEST PROGRAM
A. Preparations for Inspection
• Writing the firmware
This equipment requires firmware. When there are changes to the program for this equipment and during manufacturing processes,
it is necessary to download the new firmware to FlashRom from a PC. (If there is no firmware loaded or its checksum does not
match the correct value, when the power is first switched on, the LED on UNC flashes at one second intervals.)
The only sheet for which the firmware must be downloaded is UNC. There are two methods for writing this firmware: to write it
indirectly using the CS1D or DSP1D RS232C port or to write it directly to the AI8 UNC sheet. The detailed methods are given
below.
DSP1D RS232C
PC
AI8 Serial connection (Windows 95 or later)
D-sub 9-pin
OUTPUT A INTPUT 1 cross-cable
Serial PC
Serial connection
communications jig (Windows 95 or later)
1 2 3 4 5 6 7 8
D-sub 9-pin cross-cable
Only COM1 can be used.
UNC sheet For the connection diagram, refer to the
Connect the 5-pin PH connectors LMY-slot inspection jig specifications.
with a straight-wired cable.
1. Connect the D-sub 9-pin serial cables (cross) and DSP-CHECK board between the 5-pin connector for the target board and the
PC. At this time, do not connect other signal lines.
2. After PM1DLOAD starts up, select CardDirect with MODE SELECT, then press OK.
3. Use the setup menu to properly set the serial port to be used and then select AI8/A08 from the pull-down menu.
4. Check on the items for INPUT 1 on the list and click the write button.
5. After writing ends, end PM1DLOAD.
6. Switch off the power for AI8 and remove the PH connector, then switch the power for AI8. DSP1D on again and check that it
starts up normally. (Operation is normal if an " " is displayed in 7-segment display for AI8.)
23
AI8
Before starting inspection, refer to version.txt in the same directory as the firmware shown on the previous page and input the
version character string as instructed. (Please refer to page 24, 25)
B. Inspection Method
The inspection configuration is shown in the diagram below.
Install the inspection jig to the AI8 to be inspected as in the figure above. Send the inspection commands from the PC via the AI8 to the
LMY-slot inspection jig and take in at the PC the results returned from the LMY-slot inspection jig. Always switch on the Phantom
switch before starting the inspection. (The pop-up box is displayed on the PM1D inspection PC software when the checks start.)
AI8 AO8
Oscilloscope
IN OUT
This connection SERIAL
W.CLK I/O
LMY-slot is changed.
inspection jig OUT IN UNC Serial
communications jig
Jitter meter
DSA-1
W.CLK I/O
For jitter measurement, use either according
to the Overall Inspection Specifications. AI8 inspection jig
* Turn on the power supply for AO8 before making the connection between the AO8 on the jig side and the jig for serial
communication. Warning: Do not connect until " " is displayed on the AO8 7-segment display.
* Use the LMY-slot inspection jigs inserted into the LMY-slots. For details, see the LMY-slot inspection jig
specifications.
* Serial communications jigs are boards that convert the serial interface from the PC. For details, see the LMY-slot
inspection jig specifications.
* Set the DIP switches on the ID change jig for AI8 inspection as shown below. For details on the IC change jig, see
the LMY-slot inspection jig specifications.
SW 101 SW 102 SW 200
ID change jig
DIP switch settings
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
Input the latest version of AI8 UNC before starting the inspection. (This is necessary for the version check.) For the character string
to input, refer to version.txt in the same directory as the AI8/AI8 firmware. Details of each check item and the corresponding PC
software are shown on the following pages.
Version character string input example
Input the character string for the latest
Latest Version xxxxxxxx firmware version. When the version is
checked, this character string and the
Auto Test Start version actually written in the firmware
are compared. The value entered here
1. AI8-UNC Test OK can be retained in memory.
C. Inspection Items
The inspection items are as below. Details of the inspection items are shown on the following pages.
* However, 128 Fs Sync must be normal for the DSP to operate, so there is no special check item.
No. Item
1 AI8 - UNC test
2 AI8 - IFC2 test
3 AI8 - SLOT test
4 AI8 - IPC3, LED1 test
5 AI8 - IPC1 test
( )
SRAM OK: LED lit up
NG: LED flashes on (0.2 s) - Off (0.2 s) - On (0.2 s) - Off (0.1 s)
Flash OK: LED lit up
NG: LED flashes on (0.1 s) - Off (0.1 s) - On (0.1 s) - Off (0.1 s)
25
AI8
The +48V check assumes that the PHANTOM switch is On. The detected voltage is displayed and the
It must be switched on at the start of the AI8 inspection. percentage deviation from the ideal state
is displayed. This is shown for each slot.
26
AI8
4. AI8-IPC3, LED1 Test OK For the 75 switch item, the pop-up box is displayed below and the inspector
judges visually on the oscilloscope.
4. AI8-IPC3, LED1 Test
* Control Input Port SW OK Please check [WordClock 75ohm SW].
* W.CLK 75ohm SW OK Control Input Port SW: OK
* Phantom Master SW OK WordClock 75ohm SW: OK OK NG
Phantom Master SW: OK
* 7segments LED OK
7segments LED: OK Normal behavior on the
* W.CLK OK W.CLK: OK oscilloscope for 75 switch. ON OFF
In 48 kHz + 6%
In 44.1kHz - 10%
Jitter 48 kHz For the LED lighting order, see *1. If the LEDs light this way, they are OK.
Jitter 44.1kHz
DIR2 For the jitter ** kHz item, the pop-up box is displayed with the system in the
48/44.1 kHz output state to ask the user to measure the jitter. The inspector
In/Out
judges the jitter.
Please check [Jitter (48kHz)].
OK NG
When moving from the jitter measurement to the In/Out check, the the pop-up
Detects PLL for valid detection (IC301 of IFC3 sheet).
box is displayed to ask the user to change the connections.
Connect [AI8 BNC Out] to [AO8 BNC In].
OK
When other checks are necessary, the pop-up dialog box is displayed to ask the inspector
to select OK or NG and the system stands by until the inspector makes a selection.
Please check [Control Input Port SW].
The current switch status is displayed in real time and the inspector looks at the behavior Control Input Port SW= xxx
of the system and judges it OK/NG.
OK NG
When changing to the next port, a pop-up Change to [B port] and push OK button.
box like that on the right is displayed. OK
Change the connections and click the OK
button.
27
AI8
ERROR MESSAGES
If an error occurs in the connection to the DSP1D, or if the unit does not lock to the wordclock signal, one of the following
error indications appears.
ERROR MESSAGE DESCRIPTION
The AI8 is connected to the OUTPUT connector of the DSP1D/DSP1D-EX. Connect the AI8 to the
INPUT connector.
A cable is disconnected from the OUTPUT A, B, or C connector on the rear panel, or the connection
is made incorrectly. If the connection is proper, replace the cable.
(two dots and the ID number of the OUTPUT connector on the DSP1D/DSP1D-EX)
Illuminating or flashing dots mean that the AI8 is connected in Mirror mode from the DSP1D/DSP1D-EX.
If “.x .” lights up continuously during Mirror mode operation, the CONTROL PORT switch setting
matches the setting controlled from the CS1D and the system is operating normally.
If the control signal from the CS1D has changed the setting during Mirror mode operation and it
does not match the CONTROL INPUT PORT switch setting any more, this indicator changes in the
following order. “.x.” “. .”
“. .” “ ”( or “ ”)
“ ” means that the control signal from the CS1D has changed the setting to “A.”
“ ” means that the control signal from the CS1D has changed the setting to “B.”
During this time period, you can connect or disconnect the cable from the unselected output connector.
If you set the CONTROL PORT switch so that it matches the setting made via the control signal
from the CS1D, “.x .” lights up continuously.
28
ANALOG INPUT BOX
PARTS LIST
CONTENTS
OVERALL ASSEMBLY······························································································································ 2
SIDE PANEL ASSEMBLY ························································································································· 4
MOTHER ASSEMBLY······························································································································· 6
ELECTRICAL PARTS ························································································································· 7~12
WARNING
Components having special characteristics are marked and must be replaced with parts having
specification equal to those originally installed.
OVERALL ASSEMBLY
220 320 310 221 360
290 380 350
355
300
170 475 210
370
430 365
260
330
50 420
280
160
340
390
130 90
70 180
110
80 100
410
390b 120
390a
400 150
390c
500 480
460 140
280 240
470
270 230 530 540
560
280
460b 460a 190
40
200 285
460c
452 550 520
450
440
10
445
200 260
20
60 250
30 445 440
2
AI8
ACCESSORIES
* V4789400 Cable, SCSI DHK-HA2-3000 27
D60
70
D20
D30
D100
130
D50 120
40
30
D40 20
100 105
110 90
80b
D90 FZ400
FZ301
FZ300
D30 80a 80
D90 FZ200 D70
FZ100
D75
D10
D80
10
60
4
AI8
MOTHER ASSEMBLY
20
130 140
100
110 65
70
40
60 70
120
30
80
10 90
50
ELECTRICAL PARTS
REF NO. PART NO. DESCRIPTION REMARKS QTY RANK
CIRCUIT DIAGRAM
CONTENTS
UNC ···································································· 3
MB1····································································· 5
IFC2 ···································································· 9
IPC1 ·································································· 16
IPC3 ·································································· 17
AICOM ······························································ 18
LED1 ································································· 20
WARNING
Components having special characteristics are marked and must be replaced with parts having
specification equal to those originally installed.
P O N M L K J I H G F E D C B A
CPU 5
7
SYSTEM RESET
8
AND
AND
9
TRANSCEIVER
INVERTER AND
10
11
INVERTER
: Ceramic Capacitor
1
UNC CIRCUIT DIAGRAM 003 (AI8) AI8
TRANSCEIVER
AND
4
6
FLASH MEMORY 4M
SRAM 1M
10
11
AND
12 AND
DECODER
13
14
15
AND
DECODER
16
TRANSCEIVER : Ceramic Capacitor
10
11
10
11
10
11
2 to IFC2-CN512
to IFC2-CN505 to IFC2-CN501
from DC-CN200-1,2,7p
3
from DC-CN100-1,2,8,9p
-CN301-1p
to IFC2-CN101 to IFC2-CN506 to IFC2-CN502
from DC-CN200-3,4,8p
5 to IFC2-CN503
to IFC2-CN507 from DC-CN100-3,4,10,11p
-CN301-2p
6
from DC-CN200-5,6,9p
to IFC2-CN102
to IFC2-CN508 to IFC2-CN504
7 from LED1
from DC-CN100-5,12p
-CN101-1p
8 -CN302
10
11
INVERTER
2
from MB1-CN119
TRANSCEIVER 3
TRANSCEIVER
from DC-CN100-6,7,13,14p
-CN101-2,3p REGULATOR
8
from MB1-CN120 AND
TRANSCEIVER
AND
AND 10
AND INVERTER
11
6
FPGA
10
11
ERROM 1M
DIR2
DIR2
INVERTER
AND 8
DIR2
SYSTEM RESET
INVERTER
INVERTER
10
11
INVERTER INVERTER
4
DIR2 DIR2
INVERTER INVERTER
8
DIR2 DIR2
10
AND
11 INVERTER INVERTER
: Mylar Capacitor
from MB1-CN111
to LED1-CN100
from MB1-CN113
from MB1-CN114
TRANSCEIVER TRANSCEIVER 7
from MB1-CN115
from IPC3-CN200 8
from MB1-CN116
to MB1-CN118
from IPC3-CN300
from MB1-CN117
10
11
D-FF
4
DSP5
D-FF
D-FF
9
10
11
9
TRANSCEIVER TRANSCEIVER TRANSCEIVER
10
11
1
IPC1 CIRCUIT DIAGRAM (AI8) AI8
2 LINE DRIVER
from IFC2-CN701,705,709
LINE DRIVER
5
6
LINE DRIVER
9 LINE DRIVER
10
LINE RECEIVER
11
-CN702,706,710
LINE DRIVER
from IFC2
12
-CN703,707,711
13
from IFC2
14
-CN704,708,712
from IFC2
15
TRANSCEIVER
: Not Installed
16
to IFC2-CN510
2
LINE RECEIVER
to IFC2-CN511
LINE DRIVER
1
AICOM CIRCUIT DIAGRAM 002 (AI8) AI8
2 DC
3
to MB1-CN122-1,2,3,4p
REGULATOR +5V -CN124
REGULATOR +5V -CN127
4 REGULATOR +5V REGULATOR +3.3V IFC2-CN103
5 to MB1-CN127-4p
IFC2-CN103-5,6p
9
AC
to LED1-CN101
14
15 : Mylar Capacitor
: Metal Film Resistor
16
2
DR
from DC-CN300
not installed
to FAN
4
from IFC2-CN509
to MB1-CN126-1,3,4p
1
DC-CN400
3
2 5 1: V in 32
4 1
2: SW out
3: GND 1: OUTPUT
1: INPUT 1: INPUT
4: V os 1 1
2 2: COMMON 2 2: COMMON 2: INPUT
5: S.S 3 3: OUTPUT 3 3: OUTPUT 3: COMMON
TAB IS
GND
1
2
3 1: OUT
2: GND
3: IN