Beruflich Dokumente
Kultur Dokumente
SET.1 for
of 23
the
Date _______________
SEL-551 RelayText Settings (SET T Command)
Pickup
(OFF, 0.5–80.0 A in 0.1 A increments) (5 A nominal)
(OFF, 0.1–16.0 A in 0.1 A increments) (1 A nominal)
50P2P =
Pickup
(OFF, 0.5–80.0 A in 0.1 A increments) (5 A nominal)
(OFF, 0.1–16.0 A in 0.1 A increments) (1 A nominal)
50P4P =
Pickup
(OFF, 0.5–80.0 A in 0.1 A increments) (5 A nominal)
(OFF, 0.1–16.0 A in 0.1 A increments) (1 A nominal)
50P5P =
Pickup
(OFF, 0.5–80.0 A in 0.1 A increments) (5 A nominal)
(OFF, 0.1–16.0 A in 0.1 A increments) (1 A nominal)
50P6P =
Time Dial
0.50–15.00 for curves U1–U5
0.05–1.00 for curves C1–C5
Settings Sheets
SET.3 of
for23the
Date _______________
SEL-551 RelayText Settings (SET T Command)
Time Dial
0.50–15.00 for curves U1–U5
0.05–1.00 for curves C1–C5
51P2TD =
Pickup
(OFF, 0.5–80.0 A in 0.1 A increments) (5 A nominal)
(OFF, 0.1–16.0 A in 0.1 A increments) (1 A nominal)
50N2P =
Time Dial
0.50–15.00 for curves U1–U5
0.05–1.00 for curves C1–C5
51N1TD =
Pickup
(OFF, 0.5–80.0 A in 0.1 A increments) (5 A nominal)
(OFF, 0.1–16.0 A in 0.1 A increments) (1 A nominal)
50G2P =
Time Dial
0.50–15.00 for curves U1–U5
0.05–1.00 for curves C1–C5
51G1TD =
Pickup
(OFF, 0.5–80.0 A in 0.1 A increments) (5 A nominal)
(OFF, 0.1–16.0 A in 0.1 A increments) (1 A nominal)
50Q2P =
Time Dial
0.50–15.00 for curves U1–U5
0.05–1.00 for curves C1–C5
51Q1TD =
Time Dial
0.50–15.00 for curves U1–U5
0.05–1.00 for curves C1–C5
51Q2TD =
Reclosing Relay Open Interval Timer (see Reclosing Relay on page 3.22 )
Open Interval 1 Time
(0–54000 cycles in 0.125-cycle increments)
79OI1 =
Pickup Range
Phase Pickup
(OFF, 0.5–16.0 A in 0.1 A increments) (5 A nominal)
(OFF, 0.1–3.2 A in 0.1 A increments) (1 A nominal)
PDEMP =
Negative-Sequence Pickup
(OFF, 0.5–16.0 A in 0.1 A increments) (5 A nominal)
(OFF, 0.1–3.2 A in 0.1 A increments) (1 A nominal)
QDEMP =
Close Conditions
(other than automatic reclosing or CLOSE command)
CL =
Drive to Lockout
79DTL =
Settings Sheets
SET.11for
of 23
the
Date _______________
SEL-551 RelayText Settings (SET T Command)
79SKP =
Sequence Coordination
79SEQ =
Settings Sheets
SET.13for
of 23
the
Date _______________
SEL-551 RelayText Settings (SET T Command)
OUT2 =
Settings Sheets
SET.15for
of 23
the
Date _______________
SEL-551 RelayText Settings (SET T Command)
SLB3 =
Settings Sheets
SET.17for
of 23
the
Date _______________
SEL-551 RelayText Settings (SET T Command)
DP1_0 =
Communications Settings
LMD Prefix (@, #, $, %, &)
[PROTOCOL = LMD only]
PREFIX =
ADDRESS =
SPEED =
DATA_BITS =
SLAVE =
TIMEOUT =
AUTO =
RTS_CTS =
FAST_OP =
Protocol Settings
Set PROTOCOL = SEL for standard SEL ASCII protocol.
Set RTS_CTS = Y to enable hardware handshaking. With RTS_CTS = Y, the relay will not send characters
until the CTS input is asserted. Also, if the relay is unable to receive characters, it deasserts the RTS line.
Setting RTS_CTS is not applicable for the EIA-485 serial port option.
Set FAST_OP = Y to enable binary Fast Operate messages at the serial port. Set FAST_OP = N to block
binary Fast Operate messages. Refer to for the description of the SEL-551 Fast Operate commands.
Settings Sheets
SET.21for
of 23
the
Date _______________
SEL-551 RelayText Settings (SET T Command)
: Configuration, Fast Meter, and Fast Operate Commands
Appendix D
Appendix G
Appendix C
3.4
3.3
3.23
3.21
3.21
3.14
3.12
3.9
3.13
: Relay Elements and Logic
Section 3
4.6
4.5
3.21
3.26
3.24
3.14
4.10
3.12
4.10
4.1
: Setting Negative-Sequence Overcurrent Elements
Appendix F
3.12
: Setting Negative-Sequence Overcurrent Elements
Appendix F
3.8
4.10
4.1
3.11
3.7
4.10
4.1
3.10
3.6
4.10
4.1
3.9
4.10
4.1
3.9
3.5