Beruflich Dokumente
Kultur Dokumente
Congratulations on your purchase of the dB4LW-C wireless Computer - (Note: Battery is pre-installed) Remove the battery a) See Figure 5a and 5b for routing of cadence wire. d) Without using tie wraps - position the cadence sensor on the e) Once you have determined the approximate position of the Slide the computer onto the mounting bracket until it snaps
cycle computer with Cadence by FILZER Enterprises, Inc. - a cover from the bottom of the computer using a small coin. Fig. 2 Fig. 4a Fig. 4b left chain stay and the cadence magnet on the inside of the left sensor and cadence magnet - loosely put the cable ties on the firmly into position. Press the release button to remove the
Canadian Company. Packed with all the features that a Install the 3V battery with positive (+) pole facing the cover Computer crank. Position the sensor and magnet in such a way so that cadence magnet and cadence sensor. The magnet should be computer (Figure 7).
professional rider needs to keep track of during a workout, (Figure 1a). If the LCD shows irregular figures, take out the the magnet passes over the center portion of the sensor as maximum 2mm from the sensor and be on the inside face of
this computer is a perfect training tool for any cyclist. battery and install again. This will clear and restart the shown in figure 6a, 6b and 6c. the left crank arm.
computer's microprocessor. Max 60 cm
f) Test out the positioning of the cadence magnet and cadence
Your dB4LW-C cycling computer with Cadence will help you Battery is pre-installed Cable Ties sensor by rotating the cranks backwards to see if the computer
by providing your pedaling Cadence feedback that will allow Computer Unit x12
Fig. 1a registers a cadence value. If no value is registered reposition
you to modify your workout to achieve the maximum benefit. the sensor and magnet again.
Fig. 3 Make sure the magnet passes over the middle of the sensor as
Fig. 5a
FUNCTIONS shown in Figure 6c
Cadence Magnet Magnet Fig. 4c
Cadence ( RPM) Spoke
Transmitter Rubber Shim
Average Cadence ( RPM)
Fig. 6a
Speedometer (SPD) (0 TO 99.9 Km/hr or M/hr) Computer Battery Cable Ties
Tripometer (DST) (0 to 999.99 Km or M) (3V / CR 2032 ) Fig. 7
Magnet Transmitter
Odometer (ODO) (Up to 9999.9 Km or M) Wheel Transmitter - (Note: Battery is pre-installed) Install the Spoke
Transmitter Battery Computer battery
Auto trip timer (TM) (9:59:59) 12V battery in the wheel transmitter with the positive (+) pole Alignment Mark
Maximum Speed (MXS) (0 to 99.9 Km/hr or M/hr) facing the battery cap. Re-install the cap with a small coin and ( 12V/VR22/
L1028/A 23
) ( 3V / CR2032 )
Oversize Bracket 2mm Max.
Clock, 12/24 hour Selectable be sure it is tight to prevent moisture leakage (Figure 1b). Sensor
Left Chain
Front Wheel Stay Magnet 2mm Max. Fig. 6c
Average Speed (AVS) (0 to 99.9 Km/hr or M/hr)
Fig. 1b
Speed Comparator (+ or -) 2
Clamp the magnet on the spoke of front wheel with the screw g) Once you have positioned the magnet and sensor properly -
Speed Tendency Fig. 5b
provided and attach the sensor to the left fork using cable ties Attach the mounting bracket to the right side of the handlebar tighten up the cable ties securely and clip off the ends.
Odometer Program Function (ODO) Sensor by using a screwdriver (Figure 4a and 4b). Make sure the b) Make sure that there is enough wire clearance so the Speed
(Fig 2). Make sure the arc of magnet intersects the Sensor
Auto Scan mounting bracket is clamped tightly and will not slip on the handlebars can rotate fully in both directions without pulling at 2mm Max. h) Secure the rest of the cadence wire securely to the frame of
alignment mark on the sensor with 2mm clearance (Fig 3).
handlebar with the rubber shims provided. Adjust the position the cadence sensor wire. your bicycle with the remaining cable ties. Make sure that
Maintenance Required Functions ( ) Fig. 6b there are no dangling wires.
Transmitter Battery of the mounting bracket (Figure 4c) and fix it by locking the 3
screws tightly. c) Route the wire down the frame of your bike and to the left
(
12V/VR22/
L1028/A 23
) Mounting bracket
Rubber shims chain stay. Do NOT install tire cable ties yet. Release 1
x6
1 2 3 4 5 6 7 8 9