Beruflich Dokumente
Kultur Dokumente
E1205
advanced multi-function indicator
Description
General
This specification describes the
E1205 advanced multi-function
weight indicator, capable of
stand-alone operation, or of
integration into a larger system via
serial, FieldBus and Ethernet
interfaces.
It is a microprocessor-based
industrial weighing system with up
to 100,000 displayed increments for
analysing, displaying, storing and
transmitting gross and net weight
information.
2
Avery Weigh-Tronix Technical Specification E1205
Connection of Input
Direct wired (Buccaneer if supplied Analogue to Digital
with scale). Convertor
Excitation Display Update Rate
Direct current. 1, 2, 5, 10 per second.
Voltage A to D Rate
10 V dc. 120 per second.
Current A to D Type
Up to 460 mA Delta Sigma.
Remote Sense
Obtained from excitation, or Filter
Linked directly to reference input
connectors at the indicator. FIR & Dynamic Filtering
Seven programmable Options
Input Impedance
1MΩ paralleled with 2.2nF. Associated Filter Attributes
Filter Level Display Weight Noise Noise
Signal Response Time Sample Rate Amplitude Frequency
6-20 mV maximum. (seconds) (Hz)
uV/ per Division 0 0.20 8.13 Lowest Highest
0.6
1 0.35 8.13
Resolution 2 0.53 8.13
Approved 10,000 3 0.96 8.13
Non- Approved 100,000 4 1.45 8.13
Digital Input 5 2.09 8.13
Connects to T301 digital load cells 6 2.85 8.13 Highest Lowest
via T301 junction box.
Requires Digital Option Card.
Dynamic Filter
Applied after the FIR filter. Balance/Zero
Calibration Set the filter window size in
divisions (0 - 99). A high value will Setting
Full digital multi-point (ten point) have a large damping effect on the Keyboard push button.
calibration. weight display.
This significantly slows the scale Operation
Theoretical calibration possible if response to a legitimate change in Ignore or recall limit exceeded.
parameters known. weight.
Size of Balance Range
Provides over load report. Harmonizer™ Digital Filter Normally 2%, up to 100%.
Three programmable parameters:
Increment Multiplier Zero Indication
1, 2, 5,10, 20, 50, 100, 200, 500. Samples to Average - sets number Within 2% of maximum capacity.
of A-D conversions which will be
AVR averaged to give a weight reading. Under Range Indication
Three stage. Displays ‘Under Range’.
IIR Filter - sets how much
Gravity Compensation damping the Harmonizer™ applies Zero Tracking
Set gravity for calibration and to the weight reading. Typically Configurable
installation site. between 1 (low) - 8 (higher).
Motion Detection
Threshold Level - sets the Configurable.
minimum weight change (in
calibration units) which the
Harmonizer™ will not attempt to
filter out as noise.
3
E1205 Avery Weigh-Tronix Technical Specification
4
Avery Weigh-Tronix Technical Specification E1205
5
E1205 Avery Weigh-Tronix Technical Specification
6
Avery Weigh-Tronix Technical Specification E1205
Weight Dimensions
3.5 kg
292 188
Shipping Specification
Net
3.5 kg
Gross
4.8 kg
292
330
Measurement
345 mm x 270 mm x 335 mm
7
E1205 Avery Weigh-Tronix Technical Specification
© Avery Weigh-Tronix group of companies 2009. All rights reserved. Avery Weigh-Tronix is a registered trade mark of the Avery Weigh-Tronix group of companies. This publication is issued to provide outline information only which,
unless agreed by an Avery Weigh-Tronix group company in writing, may not be regarded as a representation relating to the products or services concerned. This publication was correct at the time of going to print however,
Avery Weigh-Tronix reserves the right to alter without notice the specification, design, price or conditions of supply of any product or service at any time.