Beruflich Dokumente
Kultur Dokumente
INSTRUCTION 1 (20)
Prepared (also subject res ponsible if other) No.
Abstract
Application
Contents
1 Revision information 2
2 GENERAL 2
3 KNOWN BUGS AND LIMITATIONS 2
4 PREREQUISITES 2
5 DEPLOY THE CLONE IMAGE INTO AN APG43/2 3
5.1 Changing Parameters on an already installed machine 3
5.2 Post cloning steps 5
5.3 AP2 Reconfiguration 6
6 SPOE IP BACKUP Definition (both AP1 and AP2) 7
7 Setup AP1 and AP2 for APZ connection 8
7.1 AP1/AP2 configuration: Common Part 8
7.2 CS parameters 13
7.3 Data Disk Quota Configuration 14
8 Final Configuration Steps 15
9 Health Check 16
10 REFERENCES 18
11 ABBREVIATIONS AND TERMINOLOGY 18
12 APPENDIX: Post Cloning steps 18
13 APPENDIX1: Workaround for burbackup 19
Limited Internal
INSTRUCTION 2 (20)
Prepared (also subject res ponsible if other) No.
1 Revision information
2 GENERAL
Cloning Instruction includes all the post installation steps to be performed on
an APG43/2 system in order to have it working and ready to be connected to
an APZ.
After reconfiguration of the system each APG43/2 is identical to the other.
4 PREREQUISITES
Hardware and Firmware requirements
Info
Limited Internal
INSTRUCTION 3 (20)
Prepared (also subject res ponsible if other) No.
NOTE: The steps reported in this chapter, if not expressly specified, need to
be performed both on AP1 and AP2 systems
NOTE: The defined Forwarders (if any) will be removed from the system
by the CloConfig procedure and needs to be reset manually after the
reconfiguration is over.
Both nodes
Delete on both nodes the directory Clone under c:\temp running the following
script:
”c:\Program Files\AP\APOS\clone\CloCleanup.vbs” –deletetemp
Node A
When asked for the “Administrator’s password”, insert it and press enter.
A prompt to allow changing the parameters will appear.
Fill the fields with the new parameters and save the changes choosing
“Set parameters and configure the system”.
The reconfiguration will continue automatically.
Since the machine has changed Network Parameters, any previously stored
backup is no longer valid. Remove any reference to the already existing
backup using the procedure reported below:
One node:
- Delete Backup Images on K drive
echo y| del \\<clustername>\k$\images\nodea\*
rmdir \\192.168.169.2\c$\acs\data\bur\clusdb /s /q
Both-nodes
Both-nodes
Launch the following scripts in this section, using GUI or SSH connections
(DO NOT USE telnet connection, see TR HL46741), in order to apply the
correct configuration for the node:
4 Run the following post configuration batch file (in case of default time
zone):
c:\temp\PostCloning\PostCloning.bat
Check the result of the Post Cloning procedure looking at the log files
stored under c:\temp\PostCloning\logs on the Active node.
NOTE: The command given without parameters will set the default time
zone: “(GMT+01:00) Amsterdam, Berlin, Bern, Rome,
Stockholm, Vienna” bound at position “0”. In case a different time
zone needs to be bound, the correct syntax is reported below:
c:\temp\PostCloning\PostCloning.bat “TZ_name” TMZ_value
Skip the following printout which may eventually occur at the end of
PostCloning script execution:
Limited Internal
INSTRUCTION 6 (20)
Prepared (also subject res ponsible if other) No.
SSH regenerate keys on active node and copying of keys to passive node
plus ssh-server-config-tool.exe included in PostCloning.bat (see Appendix A:
Post Cloning steps in chapter 13).
NOTE: all the steps in this section, if not differently mentioned, need to be
performed on the AP2 node.
Launch the following scripts in this section, using GUI or SSH connections
(DO NOT USE telnet connection, see TR HL46741), in order to apply the
correct configuration for the node:
Active-node (Node A)
1. Execute the fewer clones AP2 configuration script on the active node
(node A) of AP2. Two input parameters are foreseen for this script:
c:\TEMP\PostCloning\FewerCloneConfig_PA17.bat AP2
NOTE: It is OK if the “prcstate –l” printout shows that not all the resources are
up and running as the two nodes are not aligned (one is configured as AP2,
while the other not yet)
4. Execute the fewer clones configuration script on the new active node
(node B) for AP2:
c:\TEMP\PostCloning\FewerCloneConfig_PA17.bat AP2
Both Nodes
Active-node
Active-node
1. Assign the Administrator user the right permission to connect to the CP:
c:\temp\PostCloning\Utils\Administrator_permission.bat
Done!
2. Perform a soft function change session in order to set the correct value
for ACS_APCONFBIN_CpAndProtocolType (see ref. [ 2]).
The possible values are:
1 AP Z2123x
2 AP Z21240
3 AP Z21250
4 AP Z21255 / IO BC System s / APZ21260
After executing the steps described in each chapter (according to the required
configuration) jump to chapter 7.2.
Limited Internal
INSTRUCTION 9 (20)
Prepared (also subject res ponsible if other) No.
• APZ21230
• APZ21233
• APZ21233/C
Active node
5. Restart CS services:
C:\temp\PostCloning\APZ21233x\restartCS_delay.bat
Limited Internal
INSTRUCTION 10 (20)
Prepared (also subject res ponsible if other) No.
• APZ 212 40
Active node
2. Restart CS services:
C:\temp\PostCloning\APZ21233x\restartCS_delay.bat
• APZ 212 50
Active node
2. Restart CS services:
C:\temp\PostCloning\APZ21233x\restartCS_delay.bat
Both nodes
NOTE: Do not launch the following script in parallel on both nodes (wait until
execution is over on one node before launching this script again on the other
node).
Where X can be any of the values described in chapter 7.2 (e.g. X=5 for Evo
configuration BSC/SCP in CBA environment).
In case of dual AP configuration, connect AP1 and AP2. Verify that the
communication link is up by pinging from the AP1 the “IP Address for SPOE” of
the AP2 (192.168.169.34).
AP1 Active-node
Go to chapter 7.3.
Limited Internal
INSTRUCTION 13 (20)
Prepared (also subject res ponsible if other) No.
7.2 CS parameters
Both nodes
NOTE: Do not launch the following script in parallel on both nodes (wait until
execution is over on one node before launching this script again on the other
node).
X
ACS _CS BIN_aptType ACS _CS BIN_nodeArchitecture ACS _CS BIN_i sMultipleCPSystem
value
1 MSC Component Based A rchitecture SCP
This chapter describes how to set the Data Disk Quota Configuration for CP
Systems (default BSC). The procedure needs to be applied on both AP1 and
AP2 systems.
Active-node
where <config> parameter depends on the configuration used and the size of
the Data Disks.
See some examples below:
AP1 systems:
MSCBC-A P1-8M450 MSC-S BC HD 450 GB
MSCBC-A P1-8M600 MSC-S BC HD 600 GB
MSC MSC in Single CP HD 147 GB
HLR MSC in Single CP HD 147 GB
BSC BSC in Single CP HD 147 GB
AP2 systems:
MSCBC-A P2-8M450 MSC-S BC HD 450 GB
MSCBC-A P2-8M600 MSC-S BC HD 600 GB
NOTE: For details about other configurations, see MAN ssucfg page 1/190
80-CNZ 222 166 or Application Information 2/155 18-ANZ 222 43/5.
Limited Internal
INSTRUCTION 15 (20)
Prepared (also subject res ponsible if other) No.
1. Update nodes
swmanage -s
AP1 Active-node
AP1/AP2 Active-node
3. Once the rebooted node is up again, repeat the previous step on the
other node now active.
Limited Internal
INSTRUCTION 16 (20)
Prepared (also subject res ponsible if other) No.
9 Health Check
Required Alan tool revision for AGM319 clone is:
Due to these bugs, the following ACL errors could be reported by ALAN:
The following folders/files on the active node (B-node) have corrupt ACL's:
Folder/File Unexpected/Missing ACE
------------------------------ ------------------------------
C:\winnt\system32\apaclset.exe AUTHORITY\Authenticated Users:R
C:\winnt\system32\apaclset.exe BUILTIN\Server Operators:C
C:\winnt\system32\apaclset.exe NT AUTHORITY\SYSTEM:F
C:\winnt\system32\integrityap.exe AUTHORITY\Authenticated Users:R
C:\winnt\system32\integrityap.exe BUILTIN\Server Operators:C
C:\winnt\system32\integrityap.exe NT AUTHORITY\SYSTEM:F
C:\Program Files\AP\ACS\bin\ACS_FCH_Server.exe Missing ACE - Everyone:R
C:\Program Files\AP\ACS\bin\ACS_FCH_Server.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchcommit.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchconf.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchdump.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchend.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchevent.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchfb.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchgen.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchrst.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchstart.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\bin\fchstate.exe Missing ACE - ACSADMG:F
C:\Program Files\AP\ACS\lib\libACS_FCH_R1A_DMDN7.dll Missing ACE - Everyone:R
C:\Program Files\AP\ACS\lib\libACS_FCH_R1A_DMDN7.dll Missing ACE - ACSADMG:R
C:\Program Files\AP\ACS\lib\libACS_FCH_R1A_DMDN7.dll Missing ACE - ACSUSRG:R
C:\acs\data\FCH Missing ACE - ACSADMG:F
C:\acs\data\FCH Missing ACE - ACSUSRG:R
Limited Internal
INSTRUCTION 17 (20)
Prepared (also subject res ponsible if other) No.
10 REFERENCES
1. AGM319 User Guide for Clone Deployment, 2/198 17-CXP9040180/43-319
Active-node
3 Link to a Time Zone value (TMZ) and a platform specific Time Zone (TZ).
Both nodes
5 Setting of security.
C:\temp\PostCloning\PostInstall.bat
Limited Internal
INSTRUCTION 19 (20)
Prepared (also subject res ponsible if other) No.
Passive Node:
5 In order to have the same hostkey files on both nodes, copy the tectia
server hostkey files (hostkey and hostkey.pub) from the active to the
passive node running:
C:\temp\PostCloning\TECTIA\copy_hostkey.vbs
This type of fault usually occurs when launching the backup from node B.
sc \\%COMPUTERNAME:~0,-1%B qc burserver
TYPE : 10 WIN32_OWN_PROCESS
START_TYPE : 2 AUTO_START
ERROR_CONTROL : 1 NORMAL
TAG : 0
DISPLAY_NAME : burServer
DEPENDENCIES : RpcSs
SERVICE_START_NAME : ITSAAP013D\S9CV1aCqYA1JSN3VcKva
Check that the service user belongs to the global group "Domain Admins":
net group "Domain Admins"