Sie sind auf Seite 1von 3

DI–218

DIAGNOSTICS – ELECTRO–HYDRAULIC POWER STEERING


DI7CB–01

DTC C1552/52 PIG Power Source Drop Voltage

CIRCUIT DESCRIPTION
This circuit provides power to the vane pump assembly with motor.
DTC No. DTC Detection Condition Trouble Area
Conditions 1. and 2. continue for 1 sec. or more: S Open EHPS relay circuit
C1552/52 1. Power steering ECU terminal MH voltage is 2 V or less S EHPS relay
2. EHPS relay is ON S Vane pump assembly with motor

Fail safe function:


If the vane pump assembly with motor detects the malfunction of the power source circuit, the vane pump
assembly with motor prohibits the motor from operating and informs the malfunction by lighting up P/S warn-
ing light.

WIRING DIAGRAM
W Vane Pump Assembly
with Motor
4 4
FL Block, 1 1 EHPS 1
B B–G
4A 5 3 W–G P6 MH
J/B No. 1 IA2 4
IG Switch 1 2
1 1A
1 2 5
B–R 4 W–L P7 MRLY
AM1 IG1 R/B No. 3, 1 2 4
B–Y

W–L
J/B No. 3 EHPS Relay
2 3 3 R/B No. 4, J/B No. 4
ALT

1
ECU–IG

1
IG1 Relay

5
1
AM1

2 1
B–R
1 1 1 2 P8 IGB
2
B–L 3

FL 1 3A 3 3 2
W–B
Main 13 P6 PGND
W–B

B
IF1 W–B W–B
B–R
Battery
IE BL BM

F11480

INSPECTION PROCEDURE

1 Check P/S warning light.

NG See combination meter troubleshooting on


page BE–2.

OK

2000 MR2 (RM760U)

AuthorĂ: DateĂ: 382


DI–219
DIAGNOSTICS – ELECTRO–HYDRAULIC POWER STEERING

2 Check voltage between terminal 5 of R/B No. 4 (for EHPS relay) and body
ground.

LOCK PREPARATION:
R/B No. 4 Remove the EHPS relay from the R/B No. 4.
CHECK:
Measure the voltage between terminal 5 of the R/B No. 4 (for
EHPS relay) and body ground.
OK:
(+) (–) Voltage: 10 – 14 V

5 NG Check and repair harness or connector be-


F11482
tween R/B No. 4 and battery.

OK

3 Check EHPS relay

PREPARATION:
Remove the EHPS relay from the R/B No. 4.
CHECK:
5 3
Check the continuity between each terminal of the EHPS relay.
1 2 OK:
Terminals 1 and 2 Continuity (Reference value 80Ω)
Terminals 3 and 5 Open
Open 1
CHECK:
5 (a) Apply battery positive voltage between terminals 1 and 2.
(b) Check the continuity between the terminals.
OK:
Terminals 3 and 5 Continuity
3 2
Continuity

Continuity 1

3 2
NG Replace EHPS relay.
F11788

OK

2000 MR2 (RM760U)

AuthorĂ: DateĂ: 383


DI–220
DIAGNOSTICS – ELECTRO–HYDRAULIC POWER STEERING

4 Check continuity between terminal 3 of R/B No. 4 (for EHPS relay) and terminal
MH (P6–1) of vane pump assembly with motor connector.

R/B No. 4 CHECK:


Check the continuity between terminal 3 of the R/B No. 4 (for
EHPS EHPS relay) and terminal MH (P6–1) of the vane pump assem-
Relay 3
bly with motor connector.
OK:
Continuity
Vane Pump
Assembly
with Motor
MH (1) P6 F11483 NG Repair or replace harness or connector.

OK

Check and replace vane pump assembly with


motor.

2000 MR2 (RM760U)

AuthorĂ: DateĂ: 384

Das könnte Ihnen auch gefallen