Beruflich Dokumente
Kultur Dokumente
Page 1 of 8
Cerrar SIS
Pantalla anterior
Desarmado y Armado
12H, 140H and 160H Motor Graders Machine Systems
Número de medio -RENR4124-06 Fecha de publicación -01/09/2007 Fecha de actualización -24/09/2007
i03636467
Drawbar - Install
SMCS - 6153-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
9U-7540 Lift Stand 1
A
4C-5809 Electric Hydraulic Pump Gp 1
B 138-7575 Link Bracket 4
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/02/2012
140H Motor Grader CCA00001-UP (MACHINE) POWERED BY 3176C Engine(SE... Page 2 of 8
Illustration 1 g01014943
1. Attach Tooling (B) and a suitable lifting device to circle drive (25) . The weight of circle drive (25) is
approximately 147 kg (325 lb).
4. Install nut (24) . Tighten nut (24) to a torque of 430 ± 60 N·m (317 ± 44 lb ft).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/02/2012
140H Motor Grader CCA00001-UP (MACHINE) POWERED BY 3176C Engine(SE... Page 3 of 8
Illustration 2 g01014941
Note: Inspect ball (20) for wear. Obtaining an end play measurement from the worn area can distort
the results. Rotate ball (20) to a new spot in order to obtain the correct measurement.
5. Install adapter (21) . Install ball (20) and bolts (19) . Tighten bolts (19) to a torque of 500 ± 65 N·m
(369 ± 48 lb ft).
6. Install shims (18) and adapter (17) . Adjust shims (18) in order to obtain a end play of 0.6 ± 0.2 mm
(0.02 ± 0.008 inch).
Illustration 3 g01028532
8. Attach a suitable lifting device to drawbar (15) . Install drawbar (15) . The weight of drawbar (15) is
approximately 907 kg (2000 lb).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/02/2012
140H Motor Grader CCA00001-UP (MACHINE) POWERED BY 3176C Engine(SE... Page 4 of 8
Illustration 4 g01014937
Note: Note the number of shims (13) and the location of shoes (14) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/02/2012
140H Motor Grader CCA00001-UP (MACHINE) POWERED BY 3176C Engine(SE... Page 5 of 8
Illustration 5 g01130996
16. Install centershift cylinder (6) . Refer to Disassembly and Assembly, "Centershift Cylinder - Remove
and Install".
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/02/2012
140H Motor Grader CCA00001-UP (MACHINE) POWERED BY 3176C Engine(SE... Page 6 of 8
Illustration 6 g01016574
19. Install Tooling (B) on swivel (2) . Attach a suitable lifting device to Tooling (B) .
20. Position swivel (2) and install bolts (4) . Remove Tooling (B) . The weight of swivel (2) is
approximately 41 kg (90 lb).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/02/2012
140H Motor Grader CCA00001-UP (MACHINE) POWERED BY 3176C Engine(SE... Page 7 of 8
Illustration 7 g01014931
21. Position drawbar (1) to the original location. Remove the suitable blocking. Remove Tooling (A) .
Illustration 8 g01016589
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/02/2012
140H Motor Grader CCA00001-UP (MACHINE) POWERED BY 3176C Engine(SE... Page 8 of 8
Illustration 9 g01016417
22. Stop the engine. Measure Dimension (B) between the strip and the circle. Dimension (B) must be no
larger than 0.50 mm (0.020 inch). Add or remove shims (22) in order to obtain the correct Dimension.
23. Loosen bolts (11) in order to allow movement in shoes (14) . Seat circle drive pinion (22A) in the
teeth on circle (22A) . Move circle (22A) in order to obtain dimension (C) . Dimension (C) must be
50.0 + 2.50 - 0.50 mm (2.0 + 0.098 - 0.020 inch).
24. Evenly adjust set screws (10) against shoes (14) in order to bring shoes (14) in contact with circle
(22A) . Back off set screws (10) in order to obtain Dimension (A) . Dimension (A) must be no greater
than 0.80 mm (0.032 inch).
25. Tighten bolts (11) and the nuts to 475 ± 60 N·m (350 ± 44 lb ft). Tighten nuts (9) to 200 ± 30 N·m
(148 ± 22 lb ft).
26. Start the engine and run the engine. Rotate the circle through the entire working range and check for
binding. The circle must rotate freely.
Copyright 1993 - 2012 Caterpillar Inc. Thu Feb 9 20:26:44 UTC-0400 2012
Todos los derechos reservados.
Red privada para licenciados del SIS.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/02/2012