Beruflich Dokumente
Kultur Dokumente
This is the Multiples Choice Questions Part 9 of the Series in Modulation as one of
the Communications Engineering topic. In Preparation for the ECE Board Exam make
sure to expose yourself and familiarize in each and every questions compiled here
taken from various sources including but not limited to past Board Examination
Questions in Electronic System and Technologies, Communications Books, Journals and
other Communications References.
Modulation MCQs
PART 1: MCQs from Number 1 � 50 Answer key: PART I
PART 2: MCQs from Number 51 � 100 Answer key: PART II
PART 3: MCQs from Number 101 � 150 Answer key: PART III
PART 4: MCQs from Number 151 � 200 Answer key: PART IV
PART 5: MCQs from Number 201 � 250 Answer key: PART V
PART 6: MCQs from Number 251 � 300 Answer key: PART VI
PART 7: MCQs from Number 301 � 350 Answer key: PART VII
PART 8: MCQs from Number 351 � 400 Answer key: PART VIII
PART 9: MCQs from Number 401 � 450 Answer key: PART IX
PART 10: MCQs from Number 451 � 500 Answer key: PART X
SEE: More Questions and Answers in Modulation
Continue Practice Exam Test Questions Part IX of the Series
401. What is receiver desensitizing?
a. Desensitizing
b. Quieting
c. Cross-modulation interference
d. Squelch gain roll back
403. What is the term used to refer to a reduction in receiver sensitivity caused
by unwanted high-level adjacent channel signals?
a. Intermodulation distortion
b. Quieting
c. Desensitizing
d. Overloading
404. How can receiver desensitizing be reduced?
a. Intermodulation distortion
b. Cross-modulation interference
c. Receiver quieting
d. Capture effect
407. How can cross-modulation in a receiver be reduced?
a. Desensitization
b. Cross-modulation interference
c. Capture effect
d. Frequency discrimination
412. What is the process of detection?
a. By a balanced modulator
b. By a frequency discriminator
c. By a product detector
d. By a phase splitter
415. What is the mixing process?
a. Dynamic response
b. Gain
c. Noise figure performance
d. Bypass undesired signals
426. Which stage of a receiver primarily establishes its noise figure?
a. Noise figure
b. Blocking dynamic range
c. Signal-to-noise ratio
d. Audio output
429. What type problems are caused by poor dynamic range in a communications
receiver?
a. Filter bandwidth should be slightly greater than the received signal bandwidth
b. Filter bandwidth should be approximately half the received signal bandwidth
c. Filter bandwidth should be approximately two times the received signal bandwidth
d. Filter bandwidth should be approximately four times the received signal
bandwidth
434. How can receiver selectivity be achieved in the IF circuitry of a
communications receiver?
a. 600 millivolts
b. 600 microvolts
c. 300 millivolts
d. 300 mircovolts
436. An AM receiver is tuned to broadcast station at 600 kHz. Calculate the image
rejection in dB assuming that the input filter consists of one tuned circuit with a
Q of 40?
a. 19.28 dB
b. 39.65 dB
c. 38.57 dB
d. 19.83 dB
437. A receiver has two uncoupled tuned circuits before the mixer, each with a Q of
75. The signal frequency is 100.1 MHz. The IF is 10.7 Mhz. The local oscillator
uses high-side injection. Calculate the image rejection ratio.
a. 23.69 dB
b. 58.66 dB
c. 29.33 dB
d. 11.84 dB
438. What oscillator frequency is needed to heterodyne 626 kHz up to 3.58 MHz?
a. 2.954 MHz
b. 4.832 MHz
c. 4.210 MHz
d. 2.328 MHz
439. What is the undesirable effect of using too wide a filter bandwidth in the IF
section of a receiver?
a. Output-offset overshoot
b. Undesired signals will reach the audio stage
c. Thermal noise distortion
d. Filter ringing
440. What is the limiting condition for sensitivity in a communications receiver?
a. Bandwidth characteristics
b. Desired current gain
c. Temperature coefficient
d. Output-offset overshoot
442. What two factors determine the sensitivity of a receiver?
a. The number of kHz between the lowest and the highest frequency to which the
receiver can be tuned
b. The maximum possible undistorted audio output of the receiver referenced to one
milliwatt
c. The ratio between the minimum discernible signal and the largest tolerable
signal without causing audible distortion products
d. The difference between the lowest frequency signal detectable without moving the
tuning knob
445. Where is the noise which primarily determines the signal-to-noise ratio in a
VHF (150 MHz) marine band receiver generated?
a. Variable selectivity
b. The padder capacitor
c. Double spotting
d. Double conversion
448. A receiver has poor IF selectivity. It will therefore also have poor
a. Blocking
b. Double-spotting
c. Diversity reception
d. Sensitivity
449. If a FET is used as the first AF amplifier in a transistor receiver, this will
have the effect of
Comment Text*
Name*
Email*
Website
Notify me of follow-up comments by email. Notify me of new posts by email.
CONNECT WITH ME:
Connect with Me:
GET YOUR FREE REVIEW COURSE
Subscribe to our mailing list and get reviewers and updates to your email inbox.
RECENT POSTS
Complete List of Reviewers to Pass Engineering Board Exam
MCQ in Industrial Electronics: Principles and Applications Part 7 | �
MCQ in Tests and Measurements Part 4 | ECE Board �
MCQ in Tests and Measurements Part 3 | ECE Board �
MCQ in Power Generators, Sources, Principles, Applications Series | ECE �
PinoyBIX Engineering Copyright � 2018. Theme by MyThemeShop
About Me Copyright Terms of Use & Privacy Policy Advertise with Us
� 2014 PinoyBIX� Engineering. � 2018 All Rights Reserved | How to Donate?