Beruflich Dokumente
Kultur Dokumente
TH132 AF - G16C n DAY/HOUR/MIN—Set the day and clock settings. TH132-A The TH132 has two switches, located on the upper-left
part on the rear of the control module, which are used to
Owner’s Guide o PGM—Program the schedule (programs). This model has been designed to control a room’s ambi- set the following options:
p MODE—Select the operating mode. ent temperature.
Thank you for choosing the Aube TH132, a programma- Early Start
RETURN—To exit a function. The TH132-A has one temperature sensor located in the
ble thermostat that provides both energy savings and total
control module. When the Early Start function is enabled (disabled by
comfort. q To configure temperature setpoints: default), the TH132 calculates the optimum system start
TH132-AF - G16C - HMC4
Comfort, Economy and Vacation. time to obtain the desired temperature by the set time. To
r Adjust the floor temperature limit (AF only). This model is designed to use a floor sensor to control the enable this function:
room temperature.
s —Increase and decrease temperature. Position switch #1 down.
The TH132-AF has two temperature sensors:
t —Indicates the number of the current • The first one, installed in the control module, controls Note: When this function is enabled, the
program when Automatic mode is enabled. the ambient temperature. system can be activated before the pro-
gram’s start time.
u Current operating mode (auto / manual ). In • The second one, installed in the floor (and connected
Auto mode, the program’s associated setpoint icon is to the power base), limits the temperature of the floor Temperature Display
also displayed ( ). (the default setting of this limit is 82°F). By default, the TH132 displays the temperature in °C. If
v Indicates the room OR floor temperature. TH132-F you wish to change to °F:
w Heating indicators (see “Temperature Control” This model is designed to control floor heating systems. Position switch #2 up.
below). The TH132-F has one temperature sensor installed in the Note: When you switch from °C to °F or vice
floor (sensor is connected to the power base). versa, the , and setpoints must be
redefined.
Install the Control Module First Power ON Adjust the Temperature Setpoints Select the Operating Mode
Align the bracket tabs on the control module with the On the first installation, the screen displays:
Comfort and Economy Setpoints The TH132 offers three operating modes:
holes located on top of the power base. 0:00, MO, and temperature (room/floor).
This control module must be installed on a PB130 series These setpoints are associated with the schedule’s pro- Automatic —Executes the schedule.
power base.
For Floor Heating Installations: grams (prog. 1 & 3 = Comfort, prog. 2 & 4 = Economy)
and are preprogrammed as follows: n Press MODE to select . The current
One of the two following messages may be dis-
played when a problem occurs: program number is displayed.
Control module Air vents A & AF models— 68°F, 64°F
You can temporarily bypass the current
LO: The floor temperature is below 32°F (0°C), or F model— 82°F, 68°F program by setting a specific temperature setpoint
the temperature sensor is defective, or not
To modify a setpoint: or by selecting one of the pre-defined setpoint
connected.
n Set the temperature using and press and hold the buttons ( ). The new setpoint will be maintained
The heating indicator is displayed and until the beginning of the next program.
the relay is closed (energized). or button until it is displayed on the screen.
HI: The floor temperature is above o Press MODE/RETURN to exit. Manual —Maintains a constant temperature.
140°F (60°C), or the temperature sensor is
Vacation Setpoint n Press MODE to select .
defective.
The vacation setpoint is associated to the Vacation oper- o Set temperature or select one of the pre-
Air vents ating mode and is preprogrammed to 50°F. To modify this
Set the Time and Day setpoint, repeat above steps.
defined setpoint buttons ( ).
Vacation —Maintains the Vacation setpoint
Power base n Set the time (HOUR - MIN). Floor Temperature Setpoint (AF model only) during a prolonged absence.
The floor temperature limit is preprogrammed to 82°F to
o Set the day (DAY). Press .
Note: Keep the thermostat's air vents clean and free from avoid damage to your floor.
obstructions. To modify, press the adjustment button (below ) using a
If you remove the module from its base for more than pointed object, set the desired temperature using and
Note: The screw cannot be removed completely. 2 hours, the time and day will have to be reprogrammed. press MODE/RETURN to exit. 400-132-000-A
q Press PGM to select program 2.
Program Your Schedule Note: It is sometimes faster to program the same sched-
ule for the entire week and then to modify the exception
Programming Example
Set the time (8:30) using the HOUR and MIN buttons.
Programs MO TU WE TH FR SA SU
The schedule is used with the Automatic mode. The days. r Repeat step 4 for remaining programs:
6:00 6:00 6:00 6:00 6:00 6:00 6:00
schedule controls the heating system to automatically p Press PGM to select the program number (e.g. 1). program 3 (16:00) and program 4 (23:00).
switch between the Comfort and Economy temperature 8:30 8:30 8:30 8:30 8:30 --:-- --:--
q Press HOUR and MIN to set the start time. s When all programs are configured, press MODE/
setpoints at the times you have programmed. 16:00 16:00 16:00 16:00 16:00 --:-- --:-- RETURN to exit.
The schedule consists of 4 programs per day defined as r Repeat steps 3 to 4 for remaining programs (e.g. 2, 3
follows: and 4). 23:00 23:00 23:00 23:00 23:00 23:00 23:00 To erase programs 2 and 3 for Saturday and
s Press MODE/RETURN to exit. Sunday
Programs Setpoint Time i Comfort :
Note: After 60 seconds of inactivity, the thermostat will • Monday to Friday, between 6:00 and 8:30 and n Press PGM.
Wake-up
automatically exit programming mode. between 16:00 and 23:00. o Press PGM to select program 2.
Leave home
To clear a program time:
• Saturday and Sunday, between 6:00 and 23:00. p Press DAY to select SAturday (SA).
Back home When you clear a program time entry, the TH132 will Economy : q Press CLEAR to erase the time (--:--).
maintain the temperature setpoint of the last executed • Monday to Friday, between 8:30 and 16:00 and r Press DAY to select SUnday (SU).
Night between 23:00 and 6:00.
program until the beginning of the next program. s Press CLEAR to erase the time (--:--).
n Repeat steps 1 to 3 above. • Saturday and Sunday, between 23:00 and 6:00.
i. The programs’ start time can be different for each day of the week. t Press PGM to select program 3.
To enter the programs’ start time o Press CLEAR to erase the time entry. The time por- To program this schedule u Repeat steps 3 to 6.
To shorten programming, you simply have to enter the tion of the LCD indicates --:-- when the program is n Press PGM. v Press MODE/RETURN to exit.
inactive.
start time for each program. o Press and hold DAY for 3 seconds to select all days
n Press PGM. p Press MODE/RETURN to exit. of the week.
o Press DAY to select the day (hold for 3 seconds to p Press PGM to select program 1.
select all days of the week). Set the time (6:00) using the HOUR and MIN buttons.
Temperature Control Technical Specifications Warranty If you have any questions concerning the programming of
the TH132 programmable thermostat, call our technical
The TH132 thermostat works differently than conventional Model: TH132 A / AF / F AUBE TECHNOLOGIES INC. TWO (2) YEAR LIMITED WARRANTY support team at:
electromechanical thermostats. This product is guaranteed against workmanship defects
Display range: 32°F to 140°F (0°C to 60°C)
It is equipped with a proportional integral adaptive (PIA) for a two-year period following the initial date of purchase.
controller which determines heating cycles by analyzing Setting range (ambient): 40°F to 86°F (5°C to 30°C) During this period, AUBE Technologies Inc. will repair or
the temperature behavior history within the room. Setting range (floor): 40°F to 104°F (5°C to 40°C) replace, at our option and without charge, any defective 705 Montrichard 10 rue Ampère
The PIA controller reduces temperature swings providing Pre-programmed temperature setpoints: product which has been used under normal conditions. Saint-Jean-sur-Richelieu 95500 Gonesse
accurate temperature control while increasing user com- The warranty does not cover delivery costs and does not Quebec, Canada J2X 5K8 France
fort. Comfort: A/AF: 68°F (20°C) and F: 82°F (28°C)
apply to products poorly installed or randomly damaged
Economy: A/AF: 64°F (18°C) and F: 68°F (20°C) Tel.: (450) 358-4600 33 (0) 1 34 07 99 00
The controller determines the amount of power required following installation.
Toll Free: 1-800-831-AUBE
by the heating system to maintain the setpoint tempera- Vacation: A/F/AF: 50°F (10°C) This warranty cancels and replaces any other Fax: (450) 358-4650 33 (0) 1 34 07 99 19
ture. manufacturer's express or implied warranty as well as any Email: service@aubetech.com advaube@comintes.com
Floor limit: AF: 82°F (28°C)
When the heating system is activated, one of the following other company commitment. AUBE Technologies Inc.
icons is displayed: Temperature resolution display scale: 0.1°
cannot be held liable for related or random damages For more information on our products, visit us at:
Storage:-4°F to 120°F (-20°C to 50°C) following the installation of this product. www.aubetech.com
Software: Class A The defective product as well as the purchase invoice
Controller: Electronic must be returned to the place of purchase or mailed,
1 to 20% 21 to 40% 41 to 60% 61 to 80% 81 to 100%
prepaid and insured, to the nearest shipping address.
Temperature control: Proportional integral adaptive,
15-minute heating cycles
Programming protection: Protected memory ®
As an ENERGY STAR partner, Aube Technologies has
Clock protection: 2 hours determined that this product meets the ENERGY STAR
guidelines for energy efficiency.
Size (H/W/D): 3.3 x 3.1 x 0.5 in (83 x 79 x 13 mm)
26/08/2003 400-132-000-A
PB1 30A-230 Installation and Wiring
Installation Instructions n Remove the screw holding the
control module to the power base
230 V Li n e Vol tag e Power B ase and lift the lower part upwards. The
screw cannot be completely
removed.
Introduction
The PB130-230 power base is used to power a TH13x Series
o Before making the connections, make sure
that the base covers the electrical box
control module. The resistive load must not exceed 3450 watts entirely. If not, install a wall plate at the
(NI) @ 230 VAC (15 A). back of the base as shown.
Technical Specifications
Model: PB130A-230 s BEFORE installing the control
Supply: 230 VAC, 50 Hz module onto the base, set the
Load: 15 A maximum (resistive only) configuration switches (if any) on
Power: 3450 Watts (NI) @ 230 VAC the control module (refer to the
Conformity: EN60730-2-9 / EN50081-1 / EN50082-2 user guide).
Storage: -20°C to 50°C
Protection: Class 2
Protection degree: IP20
WARNING: This power base must be
Automatic action: Type 1.B used only with 15-minute heating cycles. If your control module
Environment: Normally polluted has a selector switch for choosing the heating cycle, ensure that the
Size (H • W • D) : 2.95 x 2.95 x 0.55 in. (75 x 75 x 14 mm) switch is correctly set.
NOTE: The terminals are designed to handle a cross-section of t Return power to the heating system.
wire measuring 0.33 to 3.1 mm2.