Beruflich Dokumente
Kultur Dokumente
Hardware Description
Compiled by Thunder-link.com
No part of this document may be reproduced or transmitted in any form or by any means
without prior written consent of Huawei Technologies Co., Ltd.
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their
respective holders.
Notice
The purchased products, services and features are stipulated by the contract made between
Huawei and the customer. All or part of the products, services and features described in this
document may not be within the purchase scope or the usage scope. Unless otherwise
specified in the contract, all statements, information, and recommendations in this document
are provided "AS IS" without warranties, guarantees or representations of any kind, either
express or implied.
The information in this document is subject to change without notice. Every effort has been
made in the preparation of this document to ensure accuracy of the contents, but all
statements, information, and recommendations in this document do not constitute a
warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
OAU1
Contents
3.2.26.6 OAU1
3.2.26.6.1 Version Description
3.2.26.6.2 Update Description
3.2.26.6.3 Application
3.2.26.6.4 Functions and Features
3.2.26.6.5 Working Principle and Signal Flow
3.2.26.6.6 Front Panel
3.2.26.6.7 Valid Slots
3.2.26.6.8 Characteristic Code for the OAU1
3.2.26.6.9 Optical Interfaces
3.2.26.6.10 Parameters Can Be Set or Queried by NMS
3.2.26.6.11 OAU1 Specifications
3.2.26.6 OAU1
OAU1: optical amplifier unit
Version Description
The available functional versions of the OAU1 board are TN11, TN12
and TN13.
Update Description
This section describes the hardware updates in V100R006C01 and later
versions as well as the reasons for the updates. Any product versions
that are not listed in the document means that they have no hardware
updates.
Application
As a type of optical amplifier unit, the OAU1 board amplifies optical
signals at the transmit end or receive end.
Front Panel
There are indicators, interfaces, and laser hazard level label on the
front panel of the OAU1 board.
Valid Slots
Two slots house one TN11OAU1 board or TN12OAU1 board, and one slot
houses one TN13OAU1 board.
Optical Interfaces
This topic describes the interface information on the U2000.
OAU1 Specifications
Specifications include optical specifications, dimensions, weight,
and power consumption.
TN11OAU Y Y Y Y N N Y Y
1
TN12OAU Y Y Y Y Y Y Y Y
1
TN13OAU Y Y Y Y Y Y Y Y
1
Type
Table 1 lists the types of the OAU1 board.
Function:
The TN11OAU1 board does not support adjustment of input optical
power, whereas the TN12OAU1 and TN13OAU1 board supports. For
details, see Working Principle and Signal Flow.
Appearance:
The TN11, TN12 and TN13 versions have different front panels.
For details, see Front Panel.
Specification:
Substitution Relationship
TN11OAU1 TN13OAU1 The TN13OAU1 can be created as OAU1 on the NMS. The
former can substitute for the latter at type
01,03,05, without any software upgrade. After
substitution, the TN13OAU1 function as the
TN11OAU1.
A TN13OAU1 board occupies one slot, and a TN11OAU1
board occupies two slots. To use a TN13OAU1 board
to substitute for a TN12OAU1 board, install the
TN11OAU1 board into the right-side slot of the two
slots that the TN11OAU1 board originally occupies
and keep the left-side slot of them vacant.
TN13OAU1 None -
Changed the default value The default value of the parameter is changed
of Channel Number Mode to based on the actual situation.
"/".
Added the TN13OAU1 board. Compared with the TN12OAU board that
occupies?two slots, the TN13OAU board
occupies?one slot.
3.2.26.6.3 Application
As a type of optical amplifier unit, the OAU1 board amplifies optical
signals at the transmit end or receive end.
For the position of the OAU1 board in the WDM system, see Figure 1.
Figure 1 Position of the OAU1 board in the WDM system
includes the noise, and the value is bigger than that of nominal gain.
Gain lock The EDFA inside the board has the gain lock function.
function Adding or dropping one or more channels or optical
signal fluctuation does not affect the signal gain of
other channels.
Working mode Supports the gain locking and power locking modes.
In the gain locking mode, the gain of the board is
tunable and users can query the actual gain of the
board. The gain locking mode is enabled by default.
The power locking mode applies to scenarios in which
there is only dummy light to lock the output power of
the board.
Transient control The EDFA inside the board has the transient control
function function. When channels are added or dropped, the board
can suppress the fluctuation of the optical power in the
path so as to implement the smooth upgrading and
expansion.
Optical-layer Supported
ASON NOTE:
The TN11OAU1 board does not support the setting of Equalization Based
OD for Optical Signal-Wavelength Commissioning.
Signal Flow
One channel of multiplexed optical signal received through the IN
interface is input to the EDFA optical module. The EDFA optical
module amplifies the optical power of the signal and locks the gain
of the signal. Then the signal is sent to the DCM through the TDC
interface for dispersion compensation and returns to the EDFA optical
module through the RDC interface. At last, the amplified multiplexed
signal is output through the OUT interface.
The VI interface receives the multiplexed signals sent from the
upstream station. After the optical power adjustment by VOA, the
signals are transmitted through the VO interface. Then, the IN
interface receives the adjusted multiplexed signals.
Module Function
VOA
Adjusts optical power of optical signals according to system
requirements.
EDFA optical module
Multiplexed signal light and pump light enter the erbium-doped
fiber for amplification. The erbium-doped fiber that is excited
by the pump laser can amplify the optical signal to implement
the optical power amplification function.
The splitter splits some optical signals from the main optical
path for optical power detection.
The splitter splits some optical signals from the main optical
path and provides them to the MON interface for detection.
Indicators
Four indicators are present on the front panel:
Interfaces
Table 1 lists the type and function of each interface.
NOTE:
For OptiX OSN 8800:
The rear connector of the board is mounted to the backplane along the right slot
in the subrack. Therefore, the slot number of the OAU1 board displayed on the NM
is the number of the right one of the two slots.
For example, if slots IU1 and IU2 house the OAU1 board, the slot number of the
OAU1 board displayed on the NM is IU2.
The rear connector of the board is mounted to the backplane along the right slot
in the subrack. Therefore, the slot number of the OAU1 board displayed on the NM
is the number of the right one of the two slots.
For example, if slots IU1 and IU2 house the OAU1 board, the slot number of the
OAU1 board displayed on the NM is IU2.
IN 1
PAOUTa 2
BAINa 3
OUT 4
RDC/TDC 5
MON 6
a: Virtual port
IN 1
PAOUTa 2
a
BAIN 3
OUT 4
RDC/TDC 5
MON 6
VI 7
VO 8
a: Virtual port
Nominal Gain (dB) Value of Nominal Specifies the expected gain of the
Gain Lower signal optical power.
Threshold (dB) to You can obtain the value range of
Value of Nominal this parameter by querying the
Gain Upper corresponding Nominal Gain Lower
Threshold (dB) Threshold (dB) and Nominal Gain
Default: The Upper Threshold (dB) parameters.
specific value is See Nominal Gain (dB) (WDM
related to the Interface) for more information.
module.
Launch Power (dBm) -60.0 to 60.0 When the incident optical power of
the transmission fiber is less than
the nominal output power of the
transmitting OA board, set Launch
Power for the transmitting OA board
to ensure desired ALC adjustment
effects.
See Setting Incident Optical Power
for more information.
a
Noise figure (NF) dB <= 8 <= 5.5 <= 5.5
Multi-channel gain slope dB/dB <= 2.0 <= 2.0 <= 2.0
Table 1 Optical specifications of the TN12OAU100 board
Pump leakage at input dBm < -30 < -30 < -30
Dynamic dB 20
attenuation
range
Adjustment accuracy dB 1
a: The gain can be adjusted continuously. The noise figure varies with the
gain. The previous table lists the noise figure when the noise figure uses
the typical value.
NOTE:
The board supports a ±2.5 dB extended gain. The extended gain is only for the temporary use because
it affects the gain flatness.
Nominal gain dB 20 26 31
Input power 40 channels dBm -32 to -16 -32 to -22 -32 to -27
range per
channel 80 channels dBm -32 to -19 -32 to -25 -32 to -30
Channel gain dB 20 to 31
Multi-channel gain slope dB/dB <= 2.0 <= 2.0 <= 2.0
Pump leakage at input dBm < -30 < -30 < -30
Dynamic dB 20
attenuation
range
b
Adjustment accuracy dB 1
a: The gain can be adjusted continuously. The noise figure varies with the
gain. The previous table lists the noise figure when the noise figure uses
the typical value.
Nominal gain dB 20 26 31
Input power 40 channels dBm -32 to -19 -32 to -25 -32 to -30
range per
channel 80 channels dBm -32 to -22 -32 to -28 -32
Table 3 Optical specifications of the TN11OAU102/TN12OAU102 board
Channel gain dB 20 to 31
Pump leakage at input dBm < -30 < -30 < -30
Dynamic dB 20
attenuation
range
Adjustment accuracyb dB 1
a: The gain can be adjusted continuously. The noise figure varies with the
gain. The previous table lists the noise figure when the noise figure uses
the typical value.
NOTE:
The board supports a ±2.5 dB extended gain. The extended gain is only for the temporary use because
it affects the gain flatness.
Nominal gain dB 24 29 36
Channel gain dB 24 to 36
Pump leakage at input dBm < -30 < -30 < -30
Dynamic dB 20
attenuation
range
b
Adjustment accuracy dB 1
a: The gain can be adjusted continuously. The noise figure varies with the
gain. The previous table lists the noise figure when the noise figure uses
the typical value.
b: The items are supported on the TN12OAU1 and TN13OAU1.
NOTE:
The board supports a ±2.5 dB extended gain. The extended gain is only for the temporary use because
it affects the gain flatness.
Nominal gain dB 23 30 34
Input power 40 channels dBm -32 to -16 -32 to -23 -32 to -27
range per
channel 80 channels dBm -32 to -19 -32 to -26 -32 to -30
a
Noise figure (NF) dB < 8.5 < 6 < 6
Channel gain dB 23 to 34
Pump leakage at input dBm < -30 < -30 < -30
Dynamic dB 20
attenuation
range
Adjustment accuracyb dB 1
a: The gain can be adjusted continuously. The noise figure varies with the
gain. The previous table lists the noise figure when the noise figure uses
the typical value.
Nominal gain dB 16 19 23
Input power 40 channels dBm -24 to -12 -24 to -15 -24 to -19
range per
channel 80 channels dBm -24 to -15 -24 to -18 -24 to -22
power
Channel gain dB 16 to 23
Pump leakage at input dBm < -30 < -30 < -30
loss
Dynamic dB 20
attenuation
range
Adjustment accuracy dB 1
a: The gain can be adjusted continuously. The noise figure varies with the
gain. The previous table lists the noise figure when the noise figure uses
the typical value.
NOTE:
The board supports a ±2.5 dB extended gain. The extended gain is only for the temporary use because
it affects the gain flatness.
Nominal gain dB 19 22 27
Input power 40 channels dBm -25 to -12 -25 to -15 -25 to -20
range per
channel 80 channels dBm -25 to -15 -25 to -18 -25 to -23
Channel gain dB 19 to 27
Pump leakage at input dBm < -30 < -30 < -30
optical power
Dynamic dB 20
attenuation
range
Adjustment accuracy dB 1
a: The gain can be adjusted continuously. The noise figure varies with the
gain. The previous table lists the noise figure when the noise figure uses
the typical value.
NOTE:
The board supports a ±2.5 dB extended gain. The extended gain is only for the temporary use because
it affects the gain flatness.
Nominal gain dB 19 22 27
Input power 40 channels dBm -25 to -13 -25 to -16 -25 to -21
Table 7 Optical specifications of the TN13OAU107 board (Maximum
total output optical power 23dBm)
range per 80 channels dBm -25 to -16 -25 to -19 -25 to -24
channel
Channel gain dB 19 to 27
Pump leakage at input dBm < -30 < -30 < -30
Dynamic dB 20
attenuation
range
Adjustment accuracy dB 1
a: The gain can be adjusted continuously. The noise figure varies with the
gain. The previous table lists the noise figure when the noise figure uses
the typical value.
NOTE:
The board supports a ±2.5 dB extended gain. The extended gain is only for the temporary use because
it affects the gain flatness.
Nominal gain dB 19 22 27
Table 9 Optical specifications of the TN13OAU107 board (Maximum
total output optical power 21dBm)
Input power 40 channels dBm -25 to -14 -25 to -17 -25 to -22
range per
channel 80 channels dBm -25 to -17 -25 to -20 -25
a
Noise figure (NF) dB <= 7.5 <= 6 <= 5.5
Channel gain dB 19 to 27
Pump leakage at input dBm < -30 < -30 < -30
Table 9 Optical specifications of the TN13OAU107 board (Maximum
total output optical power 21dBm)
Dynamic dB 20
attenuation
range
Adjustment accuracy dB 1
a: The gain can be adjusted continuously. The noise figure varies with the
gain. The previous table lists the noise figure when the noise figure uses
the typical value.
NOTE:
The board supports a ±2.5 dB extended gain. The extended gain is only for the temporary use because
it affects the gain flatness.
Mechanical Specifications
Dimensions of front panel:
Power Consumption
a: The maximum power consumption is the power consumed by the board when it
works normally under the highest ambient temperature.