Beruflich Dokumente
Kultur Dokumente
KPI Reference
Introduction: This is page one of the KPI Reference. It summarizes the KPI to let readers perform actions o
information about the KPIs, please see the corresponding explanation page in the KPI Reference.
Category Formula
Name
RA303G:Immediate Assignment
Success Rate = [
Immediate Assignment CA303J:Call Setup Indications
(Circuit Service)] x {100}/
CS Accessibili Success Rate [
CA300J:Channel Requests
(Circuit Service)]
RR370:Congestion Rate on
SDCCH per Cell (Due to Busy) =
Congestion Rate on [
K3001:Failed SDCCH Seizures
SDCCH per Cell (Due
CS Accessibili due to Busy SDCCH] x{100}/
to Busy) [
K3000:SDCCH Seizure
Requests]
ZTR104C:Call Drop Rate on
SDCCH = [
Call Drop Rate on CM30:Call Drops on SDCCH] x
{100}/
CS Accessibili SDCCH [
K3003:Successful SDCCH
Seizures]
RCA313:Assignment Success
Rate = [
Assignment Success CA313:Successful Assignments]
CS Accessibili Rate x {100}/
[
CA310:Assignment Requests]
K3041:TCH Congestion Rate
(Overflow) = {[
K3021:Failed TCH Seizures due
to Busy TCH (Signaling
Channel)]
+[
K3011A:Failed TCH Seizures due
to Busy TCH (Traffic Channel)]
+[
K3011B:Failed TCH Seizures in
TCH Congestion Rate TCH Handovers due to Busy
CS Accessibili (Overflow) TCH (Traffic Channel)]} x {100}/
{[
K3020:TCH Seizure Requests
(Signaling Channel)]
+[
K3010A:TCH Seizure Requests
(Traffic Channel)]
+[
K3010B:TCH Seizure Requests
in TCH Handovers (Traffic
Channel)]}
RH303A:Um-Interface Handover
Success Rate
= {[
CH313:Number of Successful
Outgoing Internal Inter-Cell
Handovers]
+[
Um-Interface Handover CH333:Successful Outgoing
External Inter-Cell Handovers]} x
CS Mobility KPSuccess Rate {100}/
{[
CH311:Number of Outgoing
Internal Inter-Cell Handover
Commands]
+[
CH331:Outgoing External Inter-
Cell Handover Commands]}
RH303B:Intra-BSC Handover
Success Rate
= {[
CH303:Successful Internal Intra-
Cell Handovers]
+[
CH323:Number of Successful
Intra-BSC Handover Incoming Internal Inter-Cell
CS Mobility KPSuccess Rate Handovers]} x {100}/
{[
CH300:Internal Intra-Cell
Handover Requests]
+[
CH320:Number of Incoming
Internal Inter-Cell Handover
Requests]}
RH303C:Um-Interface Intra-BSC
Handover Success Rate
= {[
CH303:Successful Internal Intra-
Cell Handovers]
+[
Um-Interface Intra-BSC CH323:Number of Successful
Incoming Internal Inter-Cell
Handover Success
CS Mobility KP Handovers]} x {100}/
Rate {[
CH301:Internal Intra-Cell
Handover Commands]
+[
CH321:Number of Incoming
Internal Inter-Cell Handover
Responses]}
TH343:Incoming Inter-BSC
Handover Success Rate
=[
Incoming Inter-BSC CH343:Successful Incoming
Handover Success External Inter-Cell Handovers] x
CS Mobility KP
Rate {100}/
[
CH340:Incoming External Inter-
Cell Handover Requests]
RH303D:Um-Interface Incoming
Inter-BSC Handover Success
Rate
Um-Interface Incoming = [
CH343:Successful Incoming
Inter-BSC Handover
CS Mobility KP External Inter-Cell Handovers] x
Success Rate {100}/
[
CH341:Incoming External Inter-
Cell Handover Responses]
TH333:Outgoing Inter-BSC
Handover Success Rate
=[
Outgoing Inter-BSC CH333:Successful Outgoing
Handover Success External Inter-Cell Handovers] x
CS Mobility KP
Rate {100}/
[
CH330:Outgoing External Inter-
Cell Handover Requests]
RH303E:Um-Interface Outgoing
Inter-BSC Handover Success
Rate
Um-Interface Outgoing = [
CH333:Successful Outgoing
Inter-BSC Handover
CS Mobility KP External Inter-Cell Handovers] x
Success Rate {100}/
[
CH331:Outgoing External Inter-
Cell Handover Commands]
1800/1900)
= {[
RH3031G:Incoming Internal
Inter-Cell Handover Requests
(900/850/810-1800/1900)]
+[
RH3033G:Incoming External
Inter-Cell Handover Requests
(900/850/810-1800/1900)]
+[
RH3035G:Outgoing External
Inter-Cell Handover Requests
(900/850/810-1800/1900)]
- {[
RH3031F:Failed Incoming
Internal Inter-Cell Handovers
Success Rate of Dual- (900/850/810-1800/1900)]
Band Handovers +[
CS Mobility KP(900/850/810- RH3033F:Failed Incoming
1800/1900) External Inter-Cell Handovers
(900/850/810-1800/1900)]
+[
RH3035F:Failed Outgoing
External Inter-Cell Handovers
(900/850/810-1800/1900)]}} x
{100}/
{[
RH3031G:Incoming Internal
Inter-Cell Handover Requests
(900/850/810-1800/1900)]
+[
RH3033G:Incoming External
Inter-Cell Handover Requests
(900/850/810-1800/1900)]
+[
RH3035G:Outgoing External
Inter-Cell Handover Requests
900/850/810)
= {[
RH3032G:Incoming Internal
Inter-Cell Handover Requests
(1800/1900-900/850/810)]
+[
RH3034G:Incoming External
Inter-Cell Handover Requests
(1800/1900-900/850/810)]
+[
RH3036G:Outgoing External
Inter-Cell Handover Requests
(1800/1900-900/850/810)]
- {[
RH3032F:Failed Incoming
Internal Inter-Cell Handovers
Success Rate of Dual- (1800/1900-900/850/810)]
Band Handovers +[
CS Mobility KP(1800/1900- RH3034F:Failed Incoming
900/850/810) External Inter-Cell Handovers
(1800/1900-900/850/810)]
+[
RH3036F:Failed Outgoing
External Inter-Cell Handovers
(1800/1900-900/850/810)]}} x
{100}/
{[
RH3032G:Incoming Internal
Inter-Cell Handover Requests
(1800/1900-900/850/810)]
+[
RH3034G:Incoming External
Inter-Cell Handover Requests
(1800/1900-900/850/810)]
+[
RH3036G:Outgoing External
Inter-Cell Handover Requests
CS413C:Number of MRs on
Uplink TCHH (Mean Receive
Quality Rank 3)]
+[
CS414C:Number of MRs on
Uplink TCHH (Mean Receive
Quality Rank 4)]}x{100}/
{[
CS410A:Number of MRs on
Uplink TCHF (Mean Receive
Quality Rank 0)]
+[
CS411A:Number of MRs on
Uplink TCHF (Mean Receive
Quality Rank 1)]
+[
CS412A:Number of MRs on
Uplink TCHF (Mean Receive
Rx_QUALITY(UPLINK) Quality Rank 2)]
CS Receive Qu +[
CS413A:Number of MRs on
Uplink TCHF (Mean Receive
Quality Rank 3)]
+[
CS414A:Number of MRs on
Uplink TCHF (Mean Receive
Quality Rank 4)]
+[
CS415A:Number of MRs on
Uplink TCHF (Mean Receive
Quality Rank 5)]
+[
CS416A:Number of MRs on
Uplink TCHF (Mean Receive
Quality Rank 6)]
+[
CS417A:Number of MRs on
Uplink TCHF (Mean Receive
CS413D:Number of MRs on
Downlink TCHH (Mean Receive
Quality Rank 3)]
+[
CS414D:Number of MRs on
Downlink TCHH (Mean Receive
Quality Rank 4)]}x{100}/
{[
CS410B:Number of MRs on
Downlink TCHF (Mean Receive
Quality Rank 0)]
+[
CS411B:Number of MRs on
Downlink TCHF (Mean Receive
Quality Rank 1)]
+[
CS412B:Number of MRs on
Rx_QUALITY(DOWNLI Downlink TCHF (Mean Receive
Quality Rank 2)]
CS Receive QuNK) +[
CS413B:Number of MRs on
Downlink TCHF (Mean Receive
Quality Rank 3)]
+[
CS414B:Number of MRs on
Downlink TCHF (Mean Receive
Quality Rank 4)]
+[
CS415B:Number of MRs on
Downlink TCHF (Mean Receive
Quality Rank 5)]
+[
CS416B:Number of MRs on
Downlink TCHF (Mean Receive
Quality Rank 6)]
+[
CS417B:Number of MRs on
Downlink TCHF
K3004:Traffic (Meanon
Volume Receive
SDCCH
Traffic Volume on =[
CS Resource SDCCH R3550M:Traffic Volume of
Signaling Channels (SDCCH)]
K3014:Traffic Volume on TCH
=[
AR3551A:Mean Number of Busy
TCHs (TCHF) (900/850/810
band)]
+[
AR3551B:Mean Number of Busy
Traffic Volume on TCH TCHs (TCHF) (1800/1900 Band)]
CS Resource +[
AR3552A:Mean Number of Busy
TCHs (TCHH) (900/850/810
band)]
+[
AR3552B:Mean Number of Busy
TCHs (TCHH) (1800/1900 Band)]
K3034:TCHH Traffic Volume
=[
AR3552A:Mean Number of Busy
TCHs (TCHH) (900/850/810
TCHH Traffic Volume
CS Resource band)]
+[
AR3552B:Mean Number of Busy
TCHs (TCHH) (1800/1900 Band)]
= {[
AR3027A:Mean Number of
Available Channels (TCHF)
(900/850/810 band)]
+[
AR3027B:Mean Number of
Available Channels (TCHF)
(1800/1900 Band)]
+[
AR3028A:Mean Number of
Available Channels (TCHH)
(900/850/810 band)]
+[
AR3028B:Mean Number of
Available Channels (TCHH)
(1800/1900 Band)]} x {100}/
{[
TCH Availability AR3017A:Mean Number of
CS Resource Dynamically Configured
Channels (TCHF) (900/850/810
band)]
+[
AR3017B:Mean Number of
Dynamically Configured
Channels (TCHF) (1800/1900
Band)]
+[
AR3018A:Mean Number of
Dynamically Configured
Channels (TCHH) (900/850/810
band)]
+[
AR3018B:Mean Number of
Dynamically Configured
Channels (TCHH) (1800/1900
Band)]}
Actual traffic volume divided by
the theoretical capacity (if the
TCH Resource Usage theoretical capacity exceeds
CS Resource 12000 Erl, take 12000 Erl for
calculation)
RK3255:TRX Usage
=[
S3656:Number of available TRXs
TRX Usage in a cell] x {100}/
CS Resource [
S3655:Number of configured
TRXs in a cell]
RR300:SDCCH Availability
= {[
AR3020A:Mean Number of
Available Channels (SDCCH)
(900/850/810 band)]
+[
AR3020B:Mean Number of
Available Channels (SDCCH)
(1800/1900 Band)]} x {100}/
SDCCH Availability {[
CS Resource AR3010A:Mean Number of
Dynamically Configured
Channels (SDCCH) (900/850/810
band)]
+[
AR3010B:Mean Number of
Dynamically Configured
Channels (SDCCH) (1800/1900
Band)]}
+[
K3013B:Successful TCH
Seizures in TCH handovers
(Traffic Channel)])
When the number of inter-RAT
handovers reaches the upper
limit, the value of this counter will
be greater than actual value if the
following formula is used:
Call drop rate on TCH per cell
(Including Handover) = X * 100/Y
Where,
X=[
Call Drops on Traffic Channel];
Y = ([
Successful TCH Seizures
(Signaling Channel)] + [
Call Drop Rate on TCH Successful TCH Seizures (Traffic
per Cell (Including Channel)] + [
CS Retainabili
Handover) Successful TCH Seizures in TCH
handovers (Traffic Channel)]);
Therefore, it is recommended
that the following formula be
used when inter-RAT handovers
are detected:
Call drop rate on TCH per cell
(Including Handover) = (X +
Number of times the outgoing
inter-RAT inter-cell handover
timer expires) * {100}/(Y +
Number of successful incoming
inter-RAT inter-cell handovers)
Notes:
Number of times the outgoing
inter-RAT inter-cell handover
timer expires = [H352C: Failed
Outgoing Inter-RAT Inter-Cell
Handovers (T8 Expired)];
CH3309A:Number of Outgoing
External Inter-Cell Handover
Requests(TCH)]
-[
CH3329A:Number of Failed
Outgoing External Inter-Cell
Handovers(TCH)])}
When the number of successful
outgoing inter-RAT handovers
reaches the upper limit, the value
of this counter will be negative or
even greater than {100} if the
following formula is used:
Call drop rate on TCH per cell
(excluding handover) = X *
{100}/Y
Where,
Call Drop Rate on TCH X = [Call Drops on Traffic
per Cell (Excluding Channel];
CS Retainabili Y = {([Successful TCH Seizures
Handover)
(Traffic Channel)]+[Number of
Incoming Internal Inter-Cell
Handover Requests (TCH)]-
[Number of Unsuccessful
Incoming Internal Inter-Cell
Handovers(TCH)]+[Number of
Incoming External Inter-Cell
Handover Requests(TCH)]-
[Number of Unsuccessful
Incoming External Inter-Cell
Handovers(TCH)]-([Number of
Outgoing Internal Inter-Cell
Handover Requests(TCH)]-
[Number of Unsuccessful
Outgoing Internal Inter-Cell
Handovers(TCH)]+[Outgoing
External Inter-Cell Handover
Requests(TCH)]-[Failed
ZTR308:Traffic Call DropOutgoing
Rate
per Cell = [
Traffic Call Drop Rate K3014:Traffic Volume on TCHs] x
{60} x {100}/
CS Retainabili per Cell [
CM33:Call Drops on Traffic
Channel]
RM333:Radio Drop Rate of TCH
= {[
CM330:Call Drops on Radio
Interface in Stable State (Traffic
Channel)]
+[
CM3606:Call Drops on Radio
Interface in Stable State
(Signaling Channel)(TCH)]} x
Radio Drop Rate of {100} /
CS Retainabili TCH {[
K3023:Successful TCH Seizures
(Signaling Channel)]
+[
K3013A:Successful TCH
Seizures (Traffic Channel)]
+[
K3013B:Successful TCH
Seizures in TCH handovers
(Traffic Channel)]}
RH333:Handover Drop Rate of
TCH = {[
RH3331:Call Drops on Signal
Channel (TCH)]
+[
K3012B:Call Drops in TCH
Handovers (Traffic Channel)]} x
{100}/
Handover Drop Rate of {[
CS Retainabili TCH K3023:Successful TCH Seizures
(Signaling Channel)]
+[
K3013A:Successful TCH
Seizures (Traffic Channel)]
+[
K3013B:Successful TCH
Seizures in TCH handovers
(Traffic Channel)]}
RA333B:Call Complete
Establishment Success Rate = [
Call Complete RA333A:BSS Call Establishment
Establishment Success Success Rate] x {1 - [
CS Retainabili ZTR304A:Call Drop Rate on TCH
Rate
per Cell (Excluding Handover)] x
{100}
A9513:Uplink Assignment
Success Rate
=[
Uplink Assignment A9502:Number of Successful
PS Accessibili Success Rate Uplink Assignments] x {100}/
[
A9501:Number of Uplink
Assignments]
A9514:Downlink Assignment
Success Rate
=[
Downlink Assignment A9508:Number of Successful
PS Accessibili Success Rate Downlink Assignments] x {100}/
[
A9507:Number of Downlink
Assignments]
Uplink TBF Establishment
Success Rate
={[
A9002:Number of Successful
Uplink GPRS TBF
Establishments]
Uplink TBF +[
Establishment Success A9202:Number of Successful
PS Accessibili Uplink EGPRS TBF
Rate Establishments]} x {100}/
{[
A9001:Number of Uplink GPRS
TBF Establishment Attempts]
+[
A9201:Number of Uplink EGPRS
TBF Establishment Attempts]}
={[
A9006:Number of Uplink GPRS
TBF Abnormal Releases due to
N3101 Overflow (MS No
Response)]
+[
A9007:Number of Uplink GPRS
TBF Abnormal Releases due to
N3103 Overflow (MS No
Response)]
+[
A9206:Number of Uplink EGPRS
TBF Abnormal Releases due to
Uplink TBF Drop Rate N3101 Overflow (MS No
PS Retainabili Response)]
+[
A9207:Number of Uplink EGPRS
TBF Abnormal Releases due to
N3103 Overflow (MS No
Response)]} x {100}/
{[
A9002:Number of Successful
Uplink GPRS TBF
Establishments]
+[
A9202:Number of Successful
Uplink EGPRS TBF
Establishments]}
Downlink TBF Drop Rate
={[
A9118:Number of Downlink
GPRS Intermit Transfers]
+[
A9318:Number of Downlink
EGPRS Intermit Transfers]} x
Downlink TBF Drop {100}/
PS Retainabili Rate {[
A9102:Number of Successful
Downlink GPRS TBF
Establishments]
+[
A9302:Number of Successful
Downlink EGPRS TBF
Establishments]}
Uplink EGPRS TBF Drop Rate
={[
A9206:Number of Uplink EGPRS
TBF Abnormal Releases due to
N3101 Overflow (MS No
Response)]
Uplink EGPRS TBF +[
A9207:Number of Uplink EGPRS
PS Retainabili Drop Rate TBF Abnormal Releases due to
N3103 Overflow (MS No
Response)]} x {100}/
[
A9202:Number of Successful
Uplink EGPRS TBF
Establishments]
Downlink EGPRS TBF Drop Rate
=[
A9318:Number of Downlink
Downlink EGPRS TBF EGPRS Intermit Transfers] x
{100}/
PS Retainabili Drop Rate [
A9302:Number of Successful
Downlink EGPRS TBF
Establishments]
=([
L9211:Total Number of Valid
Uplink EGPRS MCS1 RLC Data
Blocks]x{22}
+[
L9212:Total Number of Valid
Uplink EGPRS MCS2 RLC Data
Blocks]x{28}
+[
L9213:Total Number of Valid
Uplink EGPRS MCS3 RLC Data
Blocks]x{37}
+[
L9214:Total Number of Valid
Uplink EGPRS MCS4 RLC Data
Blocks]x{44}
+[
Average Throughput of L9215:Total Number of Valid
Uplink EGPRS RLC per Uplink EGPRS MCS5 RLC Data
PS Transmissi
Cell (kbit/s) Blocks]x{56}
+[
L9216:Total Number of Valid
Uplink EGPRS MCS6 RLC Data
Blocks]x{74}
+[
L9217:Total Number of Valid
Uplink EGPRS MCS7 RLC Data
Blocks]x{56}
+[
L9218:Number of Valid Uplink
EGPRS MCS8 RLC Data
Blocks]x{68}
+[
L9219:Total Number of Valid
Uplink EGPRS MCS9 RLC Data
Blocks]x{74}) x {8}/
({1024}x[
L9235:Total Duration of Uplink
=([
L9311:Total Number of Valid
Downlink EGPRS MCS1 RLC
Data Blocks]x{22}
+[
L9312:Total Number of Valid
Downlink EGPRS MCS2 RLC
Data Blocks]x{28}
+[
L9313:Total Number of Valid
Downlink EGPRS MCS3 RLC
Data Blocks]x{37}
+[
L9314:Total Number of Valid
Downlink EGPRS MCS4 RLC
Data Blocks]x{44}
+[
Average Throughput of L9315:Total Number of Valid
Downlink EGPRS RLC Downlink EGPRS MCS5 RLC
PS Transmissi Data Blocks]x{56}
per Cell (kbit/s)
+[
L9316:Total Number of Valid
Downlink EGPRS MCS6 RLC
Data Blocks]x{74}
+[
L9317:Total Number of Valid
Downlink EGPRS MCS7 RLC
Data Blocks]x{56}
+[
L9318:Total Number of Valid
Downlink EGPRS MCS8 RLC
Data Blocks]x{68}
+[
L9319:Total Number of Valid
Downlink EGPRS MCS9 RLC
Data Blocks]x{74}) x {8}/
({1024}*[
L9336:Total Duration of
Average Throughput of Uplink
Downlink
GPRS LLC per User (kbit/s)
=[
Average Throughput of L9422:Throughput of Uplink
Uplink GPRS LLC per GPRS Users LLC PDU]/
PS Transmissi
User (kbit/s) ([
L9421:Total Bytes of Uplink
GPRS Users LLC PDUs] x {8}/
{1024})
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None XPU %
None CPU %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None None kbit/s
None None ms
None None ms
None None ms
None None ms
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None CELL %
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
None
Test methods:
1. Use a dedicated tool (for example,
TEMS) to edit the commands for test.
2. Use the Ping command provided
with the operating system to perform
the test.
Test methods:
Use a dedicated tool (for example,
TEMS) to perform the test. A common
commercial MS cannot be used to
perform the test. Generally, the
dedicated tool supports the automatic
test, and generates a test report to
obtain the preceding counter.
Test methods:
Use a dedicated tool (for example,
TEMS) to perform the test. A common
commercial MS cannot be used to
perform the test. Generally, the
dedicated tool supports the automatic
test, and generates a test report to
obtain the preceding counter.
1. The upload test is different from the
download test. This counter is
appraised in the mode of download
test:
2. The Service Interruption Delay for
Cell Reselection (ms) is appraised
through the Um interface on some
networks. This counter is defined as
follows: the interval between the time
when the Cell Reselection message is
displayed with the MA test tool, such
as TEMS, and the time when the MS
initiates the Channel Request
message in a new cell. The signaling
shows the interval which is measured
manually.
3. The Service Interruption Delay for
Cell Reselection (ms) is impacted by
the following factors: Whether the
NACC and NC2 modes are enabled;
whether the 2G/3G inter-RAT cell
reselection is performed; whether the
cross-RA reselection is performed.
None
None
None
None
None
None
None
None