Beruflich Dokumente
Kultur Dokumente
Shaft A Shaft B
Vibration input Vibration input
1P/R CH-1 CH-6 1P/R CH-1 CH-5
88888
4. Coordinate polarity for nyquist plots is selectable 8. Easy change-over between single and dual shaft
The coordinate polarity (rotating direction) can be toggled between arrangements
clockwise and counterclockwise by means of a built-in switch. Change-over between single and dual shaft monitoring is made
easy by simply exchanging a card.
5. Choice between auto trigger and manual trigger No hardware changes are necessary.
Auto trigger with excellent followup response adopted as trigger for
the phase reference signal. Manual adjustment of the trigger 9. 5-digits digital display indicator of machine speed
threshold is also possible. Equipped with a digital display to provides a 5-digit readout of the
machine speed.
■ Signal Conditioning
Vibration sensor
Vibration sensor
Phase ref. sensor Band-pass filter
Gain
Rotor
RPM
Tracking
Phase ref. signal
Vibration signal Ao
(overall)
90
Band-pass output A
(filtered)
180 0
A
270
■ Specifications
Input channels
RPM range ■ Dual arrangement Shaft A/1 : Up to 6ch
Shaft B/1 : Up to 5ch
Single arrangement 1 to 12ch
■ 50 to 100,000rpm
Display
RPM ■ Readout 5 digits LED (red) 50 to 99,999rpm
Accuracy ±(0.003% of rdg.+1 digit) at 25°C (77°F)
Resolution 1 rpm
Trigger ■ LED (yellow)
Tracking filter
Operating range ■ 50 to 100,000rpm (0.83 to 1,666Hz)
Band width (BW) ■ 0.2Hz or 2Hz, selectable
BW select mode ■ Auto or Manual
Auto mode <1,000rpm=0.2Hz BW
>1,000rpm=2Hz BW
Filter response ■ 0.2Hz BW=0.6rpm/sec.
2Hz BW=60rpm/sec.
Dynamic range ■ 60dB or more
Analysis ratio ■ 1× (1N) or 2× (2N), selectable
Select analysis ratio ■ Manual select or TTL level select
TTL select signal L=1× (1N) (or OPEN)
H=2× (2N)
MF Series
MF-1220 Multichannel Vector Filter
Input signal
Vibration signal ■ Displacement or velocity, selectable
Input impedance 10kΩ
Input sensitivity Displacement transducer
4V/mm pk-pk, 5V/mm pk-pk, 8V/mm pk-pk
Velocity transducer
2.5 to 40mV/mm/sec. pk
Full scale range 100/200/500µm pk-pk F.S., selectable
Input channel Max. 12ch (rear panel screw terminal and BNC)
Phase reference signal input
■ Input impedance 10kΩ
Signal level 0.4 to 100V pk
Pulse width >10µs
Trigeer mode Auto or manual, selectable
Manual trigger level −20 to +20V
Trigger slope Positive or negative edge, selectable
Signal input Rear panel screw terminal and BNC
Output
RPM ■ 0.05 to 10VDC/50 to 10,000rpm or
0.005 to 10VDC/50 to 100,000rpm
Resolution 12 bit/F.S.
Overall amplitude ■ 0 to 10VDC/0 to full scale
Accuracy ±3% of F.S. at 25°C (77°F)
X,Y ■ X (real) : 0 to ±10VDC
Accuracy ±3% of F.S. at 25°C (77°F)
Y (imaginary) : 0 to ±10VDC
Accuracy ±3% of F.S. at 25°C (77°F)
Output impedance ■ 100Ω
X, Y coordinate polarity ■ CW (clockwise) or CCW (counter clockwise), selectable
Each signal output ■ Rear panel terminal and D-Sub (25p) connector
Trigger pulse ■ −0.5 to +0.5V(PL), 4 to 5V(PH)
(Front panel BNC)
180 180 -A 0 -A 0
270 270 0 +A 0 -A
A : 10V/F.S.
Others
Power supply ■ 100VAC±10%, 47 to 440Hz Max. 90VA
Insulation resitance ■ 100MΩ or more at 500VDC (power-ground)
Dielectric strength ■ 1,500VAC, 1 min. (power-ground)
Temperature range ■ Operating : 0 to 40°C (32 to 104°F)
Storage : 20 to 60°C (4 to 140°F)
Relative humidity : Up to 95% RH (noncondensing)
Front panel finish ■ Anodized aluminum, hair-line finish
Mass ■ Approx. 12kg
Accessory ■ Spare fuse (3A. 1pc.)
Power supply cable (2.5m. 1pc)
■ Outline Drawing
(Front view)
101.5
177
465 17
483 314.5
(Rear view)
446
Dimensions : mm